D.A.S. Action 12A, Action 215A, Action 18A, Action M12A, Action 218A User Manual
...
User’s Manual
action active series
Antes de utilizar el equipo, lea la sección
“Precauciones de seguridad” de este manual.
Conserve este manual para futuras consultas.
Before operating the device, please read the
“Safety precautions” section of this manual.
Retain this manual for future reference.
CONTENTS
SAFETY PRECAUTIONS
WARRANTY
DECLARATION OF CONFORMITY
INTRODUCTION
CONFIGURATIONS
2x action 12A (action 15A)
2x action 12A (action 15A) + 1x action 18A
2x action 12A (action 15A) + 2x action 18A
2x action 12A (action 15A) + 2x action 218A
2x action 215A
4x action M12A
LINE DRAWINGS
AMPLIFIER
Description
ON / OFF
Overload indicators
Equalisation
Overheating
Low mains voltage
3
4
5
6 a 7
8 a 13
14
15 a 17
Current consumption
Troubleshooting
SPECIFICATIONS
RIGGING SYSTEM
APPENDIX
Line connections: unbalanced and balanced
18
19 a 20
21
Manual del Usuario / action active / User’s Manual
Precauciones de Seguridad
action active series
Cajas acústicas activas / Self-powered loudspeaker enclosures
Safety Precautions
El signo de exclamación dentro de un triángulo indica la
existencia de importantes instrucciones de operación y
mantenimiento en la documentación que acompaña al producto.
Conserve y lea todas estas instrucciones. Siga las advertencias.
ATENCIÓN: Es un producto clase A, por lo que en entornos
domésticos puede causar radio-interferencias, en cuyo caso el
usuario tendrá que tomar las medidas oportunas.
De acuerdo con EN55103-2, usar el equipo sólo en entornos E1,
E2, E3 ó E4.
No desconecte la tierra en el conector de alimentación pues es
peligroso e ilegal. Equipo de Clase I.
El signo del rayo con la punta de flecha, alerta contra la
presencia de voltajes peligrosos no aislados. Para reducir el
riesgo de choque eléctrico, no retire la cubierta.
Sólo use este equipo con el cable de red de alimentación
adecuado para su país.
No instale el aparato cerca de ninguna fuente de calor como
radiadores, estufas u otros aparatos que produzcan calor. Debe
instalarse siempre sin bloquear la libre circulación de aire por las
aletas del radiador.
Si los altavoces action se utilizan al aire libre en un día soleado,
colocar los altavoces en un área sombreada o a cubierto. Los
amplificadores de los altavoces tienen circuitos de protección
que silenciarán temporalmente el altavoz cuando las
temperaturas que se alcanzan sean extremadamente altas. Esto
puede suceder en los días calurosos cuando el altavoz esté
expuesto a la luz solar directa.
No exponga este equipo a la lluvia o humedad. No use este
aparato cerca del agua (piscinas y fuentes, por ejemplo). No
exponga el equipo a salpicaduras ni coloque sobre él objetos
que contengan líquidos, tales como vasos y botellas. Equipo IP-
20.
Este símbolo indica que el presente producto no puede ser
tratado como residuo doméstico normal, sino que debe
entregarse en el correspondiente punto de recogida de equipos
eléctricos y electrónicos.
Equipo diseñado para funcionar entre 15ºC y 42ºC con una
humedad relativa máxima del 95%, con un rango de ±10% de la
tensión nominal de alimentación indicada en la etiqueta trasera
(según IEC 60065:2001). Si debe sustituir el fusible preste
atención al tipo y rango.
El cableado exterior conectado al equipo requiere de su
instalación por una persona instruida o el uso de cables flexibles
ya preparados.
Si el aparato es conectado permanentemente, la instalación
eléctrica del edificio debe incorporar un interruptor multipolar con
separación de contacto de al menos 3mm en cada polo.
Desconecte este aparato durante tormentas eléctricas,
terremotos o cuando no se vaya a emplear durante largos
periodos.
No emplace altavoces en proximidad a equipos sensibles a
campos magnéticos, tales como monitores de televisión o
material magnético de almacenamiento de datos.
Para las cajas con vaso para trípode, la altura máxima de
seguridad desde el suelo a la base de la caja montada sobre
trípode modelo TRD-2, con pies a 55 cm del eje del trípode, es:
The exclamation point inside an equilateral triangle is intend to
alert the users to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the product. Heed all warnings. Follow all
instructions. Keep these instructions.
WARNING: This is a class A product. In a domestic environment
this product may cause radio interferences in which case the
user may be required to take adequate measures.
Use this product only in E1, E2, E3 or E4 environments
according to EN55103-2.
Do not remove mains connector ground, it is dangereous and
illegal. Class I device.
The lightning and arrowhead symbol warns about the presence
of uninsulated dangerous voltage. To reduce the risk of electric
shock, do not remove the cover.
Only use this equipment with an appropriate mains cord for your
country.
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus that produce heat. The
circulation of air through the heatsink must not be blocked.
If action loudspeakers are used outdoors on a sunny day, place
the loudspeakers in a shaded or covered area. The loudspeaker
amplifiers have protection circuits that temporarily shut the
loudspeaker off when extremely high temperatures are reached.
This can happen on hot days when the loudspeaker is in direct
sunlight.
Do not expose this device to rain or moisture. Do not use this
apparatus near water (for example, swimming pools and
fountains). Do not place any objects containing liquids, such as
bottles or glasses, on the top of the unit. Do not splash liquids
on the unit. IP-20 equipment.
This symbol on the product indicates that this product should
not be treated as household waste. Instead it shall be handed
over to the appicable collection point for the recycling of
electrical and electronic equipment.
Working temperature ranges from 15ºC to 42ºC with a relative
humidity of 95%, with ±10% of the rated main voltage value
indicated on the rear label (according to IEC 60065:2001). If the
fuse needs to be replaced, please pay attention to correct type
and ratings.
The outer wiring connected to the device requires installation by
an instructed person or the use of a flexible cable already
prepared.
If the apparatus is connected permanently, the electrical system
of the building must incorporate a multipolar switch with a
separation of contact of at least 3mm in each pole.
Unplug this apparatus during lightning storms, earthquakes or
when unused for long periods of time.
Do not place loudspeakers in proximity to devices sensitive to
magnetic fields such as television monitors or data storage
magnetic material.
For enclosures with tripod socket, the maximum safety height
from floor to bottom of enclosure when mounting on a TRD-2
tripod, with legs spread 55cm from the central pole, is:
action-12A ------------->115 cm
action-15A ------------->105 cm
El colgado del equipo sólo debe realizarse utilizando los herrajes
de colgado recomendados y por personal cualificado. No
cuelgue la caja de las asas.
No existen partes ajustables por el usuario en el interior de este
equipo. Cualquier operación de mantenimiento o reparación
debe ser realizada por personal cualificado. Es necesario el
servicio técnico cuando el equipo se haya dañado de alguna
forma, como que haya caído líquido o algún objeto en el interior
del aparato, haya sido expuesto a lluvia o humedad, no funcione
correctamente, haya recibido un golpe o su cable de red esté
dañado.
Limpie con un paño seco. No use limpiadores con disolventes.
La reventa del producto sólo es posible incluyendo el manual de
usuario. Cualquier cambio producido en el producto tiene que
ser documentado por escrito y aprobado por el comprador en el
momento de la reventa.
Manual del Usuario / action active / User’s Manual
55 cm
action-12A ------------->115 cm
action-15A ------------->105 cm
The appliance should be flown only from the rigging points and
by qualified personnel. Do not suspend the box from the
handles.
No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
Clean only with a dry cloth. Do not use any solvent based
cleaners.
Reselling of the product is only possible if the user manual is
aviable. Any changes made to the product have to be
documented in writing and passed on to the buyer in the event
of resale.
3
GARANTÍA
Todos nuestros productos están garantizados por un periodo de 24
meses desde la fecha de compra.
Las garantías sólo serán válidas si son por un defecto de
fabricación y en ningún caso por un uso incorrecto del producto.
Las reparaciones en garantía pueden ser realizadas,
exclusivamente, por el fabricante o el servicio de asistencia técnica
autorizado.
Otros cargos como portes y seguros, son a cargo del comprador
en todos los casos.
Para solicitar reparación en garantía es imprescindible que el
producto no haya sido previamente manipulado e incluir una
fotocopia de la factura de compra.
WARRANTY
All D.A.S. products are warrantied against any manufacturing defect
for a period of 2 years from date of purchase.
The warranty excludes damage from incorrect use of the product.
All warranty repairs must be exclusively undertaken by the factory
or any of its authorised service centers.
To claim a warranty repair, do not open or intend to repair the
product.
Return the damaged unit, at shippers risk and freight prepaid, to
the nearest service center with a copy of the purchase invoice.
4
Manual del Usuario / action active / User’s Manual
DECLARACIÓN DE CONFORMIDAD
DECLARATION OF CONFORMITY
D.A.S. Audio, S.A.
C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España
(Spain).
Declara que la serie action:
Declares that action series:
Cumple con los objetivos esenciales de las Directivas:
Abide by essential objectives relating Directives:
lDirectiva de Baja Tensión (Low Voltage Directive) 2006/95/CE
lDirectiva de Compatibilidad Electromagnética (EMC) 2004/108/CE
lDirectiva RoHS 2002/95/CE
lDirectiva RAEE (WEEE) 2002/96/CE
Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:
lEN 60065:2002 Audio, video and similar electronic
apparatus. Safety requirements.
lEN 55103-1:1996 Electromagnetic compatibility.
Product family standard for audio, video, audiovisual and entertainment lighting control apparatus
for professional use. Part 1:Emission.
lEN 55103-2:1996 Electromagnetic compatibility.
Product family standard for audio, video, audiovisual and entertainment lighting control apparatus
for professional use. Part 2:Immunity.
Manual del Usuario / action active / User’s Manual
5
INTRODUCTION
The action series inherits the exceptional sound quality and rugged build that have made D.A.S.
professional systems an internacional sound reinforcement standard. Designed from “real-world” experience,
they offer users outstanding performance, absolute reliability, and unparalleled convenience. Whether it is in a
high-profile venue or on the stage of a major event, the action series will provide the power and definition
needed to make your performance a success.
Features
action 12A
-Two-way powered system
-12" bass loudspeaker
-Compression driver with titanium diaphragm
-Asymmetric enclosure design for stage monitor
use
-Built-in rigging points (eyebolt based)
-Stand mountable
The action 12A is a powered loudspeaker (2
channel Class D amplifier), that utilizes a 12” low
frequency transducer and a 1” exit compression
driver. The multi-angle cabinet is constructed of
Birch plywood protected by an environmentally
friendly black paint finish. Two bar handles and a
steel grille are provided. A 35mm tripod socket
allows for stand mounting.
action M12A
-Dedicated powered stage monitor
-12" bass loudspeaker
-Compression driver with titanium diaphragm
-Low profile enclosure design for minimum
visual impact
-Black paint finish
-Stand mountable
The action M12A is a dedicated powered stage
monitor (2 channel Class D amplifier). The
enclosure is constructed from Birch plywood and
is protected with a black paint finish. Two side
located handles facilitate handling and a steel grille
protects the components. A pole mount socket
adds versatility to the action M12A.
action 15A
-Two-way powered system
-15" bass loudspeaker
-Compression driver with titanium diaphragm
-Asymmetric enclosure design for stage monitor
use
-Built-in rigging points (eyebolt based)
-Stand mountable
This is a powered loudspeaker (2 channel
Class D amplifier), utilizes a 15” low frequency
transducer and a 1” exit compression driver with
titanium diaphragm. The cabinet is constructed of
Birch plywood and finished with an environmentally
friendly black paint finish. Two bar handles are
provided and a steel grille protects components. A
35 mm tripod socket allows for stand mounting.
Rigging points provide a safe and simple solution
for suspending the action 15A.
6
Manual del Usuario / action active / User’s Manual
action 215A
-2-way powered system
-2 x 15" bass loudspeaker
-Compression driver with titanium diaphragm
-Two steel-reinforced handles
The action 215A is a powered loudspeaker (2
channel Class D amplifier), that utilizes two 15”
bass loudspeakers for extra low frequency punch
and higher SPL. High frequencies are handled by a
1” compression driver with titanium diaphragm. The
trapezoidal cabinet is constructed using Birch
plywood and protected with a hard-wearing black
paint finish. Two bar handles and a steel grille
sealed against corrosion using a polyamide powder
coat finish are provided. Rigging points provide a
safe and simple way to fly the action 215A cabinets.
action 18A
-Bass-reflex powered subwoofer system
-18" low frequency transducer
-Precise and powerful bass reproduction
-Top located pole mount socket
The action 18A bass powered system (Class D
amplifier) incorporates a 18” low frequency
transducer with a 4 " voice coil mounted as a
direct radiator into a bass-reflex cabinet. The
loudspeaker is protected by a perforated steel
grille, sealed against corrosion using a powder
coat finish. The action 18A is designed for use in
biamped systems. A top located pole-mount
socket permits mounting full-range systems above
the action 18A and two bar handles makes moving
easy.
-High output bass-reflex powered subwoofer
system
-Twin 18" loudspeakers
-Durable black paint finish
-Side located bar handles
This bass-reflex powered subwoofer system
uses dual 18" bass loudspeakers equipped with 4"
voice coils. The exceptional power handling
capacity and efficiency provide high sound
pressure levels of powerful bass. Two hand
locations facilitate handling. The cabinet is
designed to be stacked in the vertical position in
order to reduce the units "on-stage" footprint.
Manual del Usuario / action active / User’s Manual
action 218A
7
Loading...