DAP Audio GIG-124CFX Service Manual

GIG-124CFX V1
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Order code: D2285
ENGLISH
GIG-124CFX
Order code: D2285
Table of contents
Warning ............................................................................................................................................................................... 2
Unpacking Instructions ................................................................................................................................................. 2
Safety Instructions ......................................................................................................................................................... 2
Operating Determinations .......................................................................................................................................... 4
Return Procedure .......................................................................................................................................................... 4
Claims .............................................................................................................................................................................. 4
Description of the device ................................................................................................................................................. 5
Features .......................................................................................................................................................................... 5
Overview ........................................................................................................................................................................ 5
Installation ........................................................................................................................................................................... 6
Introduction .................................................................................................................................................................... 6
Ready to start ................................................................................................................................................................ 6
Control Elements ................................................................................................................................................................ 7
Modules .............................................................................................................................................................................12
Option One - SMP-S (Order code: D2290) .............................................................................................................12
Option Two - SMP-R (Order code: D2291) .............................................................................................................14
Option Three - Bluetooth Version 2.1 (Order code: D2292) ................................................................................15
Installation and connection ..........................................................................................................................................16
Connection Cables .........................................................................................................................................................17
Block Diagram .................................................................................................................................................................18
Preset List GIG-124CFX ...................................................................................................................................................19
Technical Specifications ................................................................................................................................................20
Dimensions ........................................................................................................................................................................22
1
GIG-124CFX
Order code: D2285
Your shipment includes:
GIG-124CFX mixing console 3-pin IEC power cable User manual
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Safety Instructions
Every person involved with the installation, operation and maintenance of this system has to:
be qualified
follow the instructions of this manual
Before you initial start-up, please make sure that there is no damage caused by transportation. Should there be any, consult your dealer and do not use the system.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the system are not subject to warranty.
This system contains no user-serviceable parts. Refer servicing to qualified technicians only.
2
GIG-124CFX
Order code: D2285
Disposing of this product should not be placed in municipal waste and should be separate collection.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the system.
Never let the power-cord come into contact with other cables! Handle the power-cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit. Never use anything to cover the ground contact. Never leave any cables lying around. Do not insert objects into air vents. Do not connect this system to a dimmer pack. Do not switch the system on and off in short intervals, as this would reduce the system’s life. Do not open the device and do not modify the device. Do not drive the inputs with a signal level bigger, than required to drive the equipment to full output. Do not plug Mics into the console (or stage box) while Phantom Power is on. Also mute the monitor /
Pa system when turning Phantom Power on or off. Allow the system to adjust for a couple of seconds, before setting the input gains.
Only use system indoor, avoid contact with water or other liquids. Avoid flames and do not put close to flammable liquids or gases. Always disconnect power from the mains, when system is not used. Only handle the power-cord by
the plug. Never pull out the plug by tugging the power-cord.
Always operate the unit with the AC ground wire connected to the electrical system ground. Make sure you don’t use the wrong kind of cables or defective cables. Make sure that the signals into the mixer are balanced, otherwise hum could be created. Make sure you use DI boxes to balance unbalanced signals; All incoming signals should be clear. Make sure that the available voltage is not higher than stated on the rear panel. Make sure that the power-cord is never crimped or damaged. Check the system and the power-
cord from time to time.
Please turn off the power switch, when changing the power cord or signal cable, or select the input
mode switch.
Extreme frequency boosts in connection with a high input signal level may lead to overdriving your
equipment. Should this occur, it is necessary to reduce the input signal level by using the INPUT control.
To emphasize a frequency range, you don’t necessarily have to move its respective control upward;
try lowering surrounding frequency ranges instead. This way, you avoid causing the next piece of equipment in your sound path to overdrive. You also preserve valuable dynamic reserve (“headroom”)
Avoid ground loops! Always be sure to connect the power amps and the mixing console to the
same electrical circuit to ensure the same phase!
If system is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your system. Leave the system switched off until it has reached room temperature.
If your Dap Audio device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material)and return it to your Dap Audio dealer for service.
Repairs, servicing and electric connection must be carried out by a qualified technician. For replacement use fuses of same type and rating only. WARRANTY: Till one year after date of purchase.
3
GIG-124CFX
Order code: D2285
Return Procedure
Operating Determinations
This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
The minimum distance between light-output and the illuminated surface must be more than 0.5
meter.
The maximum ambient temperature t The relative humidity must not exceed 50 % with an ambient temperature of 35° C. If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
= 45°C must never be exceeded.
a
You endanger your own safety and the safety of others!
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short­comings and/or visible defects, or perform this check after our announcement that the goods are at their disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping. Transportation damage has to be reported to us within one day after receipt of the delivery. Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless otherwise agreed in writing. Complaints against us must be made known in writing or by fax within 10 working days after receipt of the invoice. After this period complaints will not be handled anymore. Complaints will only then be considered if the client has so far complied with all parts of the agreement, regardless of the agreement of which the obligation is resulting.
4
GIG-124CFX
Order code: D2285
Description of the device
Features
Ultra-low noise discrete MIC Preamps with +48V Phantom Power. 4 MIC Input Channels with XLR and balanced Line Input, Insert I/O and Compressor control. Low Cut for each MIC Input. 2 Stereo Input Channels with mono XLR Input and TRS Jack. 2 Stereo Input Channels with RCA Jack and TRS Jack. 3-band EQ and Peak LED on each MIC channel. 2-band EQ and Peak LED on Stereo channels. 1 AUX Send POST/PRE per channel for monitoring or external effects, 1 FX send POST Fader for internal
effects or monitoring.
Mute and PFL function for each channel, 60mm Fader for level control. GR1/2 and Main L/R bus assign for each channel. 2-Track Input assignable to Main Mix or Control Room/Headphone Output. Balanced XLR & TRS outputs for Main Mix. Built-in 24-bit DSP effect with 100 presets. Optional MP3 player or Bluetooth player. Internal switch-mode power supply for maximum flexibility 100-240V.
Overview
5
GIG-124CFX
Order code: D2285
Installation
Introduction
This is a professional compact mixer, which gives you great quality and better reliability than ever before. You will get the smooth, accurate, more natural and open sound from this device. It is really ideal for gigs, recording and fixed PA installations.
The GIG-124CFX Mixing Console is packed with features that cannot be found in other consoles of its size:
4 mono (provided with ultra-low noise microphone pre-amplifiers and Phantom Power at +48 Volt ) 4 stereo input channels, each of them provided with a 3-band equalizer for HI, MID and LOW control 2 auxiliary controls highly accurate 12-segment bar graph meter 2-track input assignable to main mix, control room/phones outputs, etc.
This unit is very easy to operate, but we advise you to go through each section of this manual carefully.
Ready to start
01) Please check the available AC voltage in your country before connecting your mixer to the AC
socket.
02) Be sure that the main power switch is turned off before connecting the mixer to the AC socket. You
should also make sure that all input and output controls are turned down. This will avoid damage to your speakers and avoid excessive noise.
03) Always turn on the mixer before you turn on the power amplifier; turn off the mixer after the power
amplifier is turned off.
04) Before connecting and disconnecting the unit from the power source, always turn off the unit.
05) Cleaning: Disconnect the mains power supply and then wipe the mixer with a damp cloth. Do not
immerse in liquid. Do not use alcohol or solvents.
6
GIG-124CFX
Order code: D2285
1. MIC INPUT JACKS (CHs 1 to 7/8)
The balanced XLR input connects to microphones, DI boxes and multicores.
2. LINE INPUT JACKS (CHs 1 to 4)
This is a ¼" jack connector which connects to line-level signal sources (for example, keyboards, CD players and wireless microphone receivers). The input is balanced (TRS connector) but can also be used with unbalanced connectors (TS connector).
3. LINE INPUT JACKS (CHs 5/6 to 11/12)
The stereo channels consist of two line inputs (¼" jacks), one for the left and one for the right channel. The inputs are unbalanced (TS connectors). These channels can also be used as mono channels by connecting to the jack labeled “L” (left).
4. LINE INPUT JACKS (CH 9/10 to 11/12)
These are unbalanced stereo RCA pin jacks. NOTE: Where an input channel provides both a MIC input jack and a LINE input jack or a LINE input jack and RCA pin jack, you can only use one pair of jacks at a time but not both pairs at the same time. Please connect to only one jack on each channel.
5. INSERT JACKS
The INS(ert) connector (¼" stereo jack connector) is used to connect to external signal processors. Here you can hook up a compressor, noise gate or equalizer to process the signal of a single channel. The insert jack is placed before the fader, EQ and aux send. Please use an insert cable to connect to the insert point.
6. GAIN CONTROL
The GAIN CONTROL adjusts the input gain. Be sure to set this control fully counter-clockwise before you connect or disconnect a signal source to or from one of the inputs. MONO: The first value range between 0 and +50 refers to the microphone input, indicating the degree of amplification applied to the input's signal. The second value range between +15 and -35 dB refers to the amplification of the line input. STEREO: The first value range between 0 and +40 refers to the microphone input, indicating the degree of amplification applied to the input's signal. The second value range between +20 and -20 dB refers to the amplification of the line input.
7. LOW CUT
Press the LOW CUT switch to activate the high-pass filter which blends out low-frequency noise (100 Hz, 18 dB/octave).
8. COMPRESSOR CONTROL
Adjust the amount of compression applied to the channel. Turn the control to the right to increase the compression ratio and the output gain will automatically be adjusted. The result is smoother, more even dynamics, because louder signals are attenuated when the overall level is boosted.
Control Elements
7
GIG-124CFX
Order code: D2285
9. EQUALIZER
Hi
The high-frequency range is processed with a shelving filter above 12 kHz. You can boost or cut the bands up to 15 dB. When in center position (0 dB), the equalizer has a flat response.
MID
The HIGH MID control adjusts the mid frequency range. This Is a peak filter which boosts and cuts the frequencies centered at 2,5 kHz. You can boost or cut the bands up to 15 dB. When in center position (0 dB), the equalizer has a flat response.
Low
The low-frequency range is processed with a shelving filter below 80 Hz. You can boost or cut the bands up to 15 dB. When in center position (0 dB), the equalizer has a flat response.
10. AUX
The aux bus is used as additional, flexible send path for various applications. The AUX control adjusts the volume level of the channel signal in the aux bus.
11. PRE/POST
Press the PRE/POST switch to change the routing of the aux path from “post-fader” to “pre-fader.” This way the volume level of the effects signal is not affected by the channel fader.
12. FX/POST
The FX bus is used as send path to the internal effect unit. The signal is tapped after the channel fader and therefore is affected by the position of the channel fader. The FX control adjusts the volume level of the channel signal to the effects unit.
13. PAN/BAL CONTROL.
The PAN control determines the position of the channel signal in the stereo mix as well as the subgroup, to which the channel signal is routed.
14. MUTE
The MUTE switch mutes the channel. This means that the channel signal has been removed from the main mix and subgroups. At the same time the FX, monitor and aux paths of the respective channel are muted as well. The corresponding MUTE LED indicates, that the channel has been muted.
15. PFL
Press the PFL switch to hear the signal on your headphones and simultaneously see it on the monitor display. The corresponding LED lights up when the solo function is activated.
16. PEAK LED
The PEAK LED lights up as soon as the channel's level is too high. In this case, reduce the channel's input amplification with the GAIN control. The Peak LED lights at a level of 3 dB below clipping.
8
GIG-124CFX
Order code: D2285
17. GR1-2
Each channel is equipped with a GR1-2 switch, which allow you to feed multiple channels to a stereo mix down. The volume level can be adjusted using the GR1-2 LEVEL fader.
18. MAIN
Each channel is equipped with a MAIN switch, pressing this button will send the signal to the MAIN MIX bus.
19. LEVEL
The channel fader adjusts the level of the channel signal as part of the main mix (or subgroup).
20. MAIN MIX LEVEL
Use this high-precision MAIN fader to control the output level of the main mix.
21. GR1-2 LEVEL
Use this high-precision GROUP1-2 fader to control the output level of the subgroup mix.
22. FX LEVEL
The FX LEVEL fader adjusts the volume level of the returned effect signal in the MIAN MIX.
23. 2-TRACK SIGNAL PATH
If you push down the 2 TRACK SIGNAL PATH switch, the 2 TRACK IN signal will be routed to the CONTROL ROOM output. Push the switch again, the 2TRACK IN signal will be routed into the MAIN MIX output.
24. 2-TK IN/MP3
This control allows you to adjust the level of the 2-tk in/mp3.
25. MAIN MIX/GR1-2
If you push down the MAIN MIX/GR1-2 button, the signal from GR1-2 will be routed into the CONTROL ROOM output. Push the switch again, the signal from MAIN MIX will be routed into the CONTROL ROOM output.
26. PHONES/CONTROL ROOM
The PHONES/CONTROL ROOM control adjusts the volume level of all signals routed to the headphone and the CONTROL ROOM outputs.
27. OUTPUT LEVEL
This stereo 12 segments LED meter will indicate the level of the overall output signal.
28. FX
This is the master FX control for adjusting the volume of all FX send signals at the input of the built-in effect processor.
9
GIG-124CFX
Order code: D2285
29. AUX SEND
The Master AUX SEND control adjust the signals volume level of the respective aux send connector. This way you adjust the sum of the AUX signal on the input channels.
30. ST RETURNS TO AUX
This control assigns the ST RETURN signal to their respective AUX SEND outputs.
31. ST RETURNS TO MAIN
This control assigns the ST RETURN signal to their respective MAIN MIX outputs.
32. FX TO AUX
This control is used to assign the signal from the FX to the AUX SEND output.
33. PROGRAM(PUSH) Adjust this knob to select the desired effect. There are 100 options: Echo, Vocal, Plate and versatile two­effect combination.
34. DIGITAL EFFECTS
It displays the selected preset.
35. PHANTOM LED
This LED indicates when the phantom power is switched on for the microphone inputs.
36. PWR LED
This LED indicates when the power is switched on.
37. 2TK IN / OUT
TAPE IN
The CD/TAPE input connectors are used to hook up CD players, tape decks or other line-level sources.
TAPE OUT
The CD/TAPE output connectors provide the stereo main mix signal to a tape deck or DAT recorder to record your mix.
38. MAIN MIX OUTPUT The MAIN MIX outputs are balanced XLR connectors - 1/4" TRS sockets and provide the main mix signal.
39. ST RETURNS
The ST RETURNS inputs L and R let you connect the mixer to additional equipment (players, effects processors, sub mixers, etc.).
40. CTRL-ROOM
The CTRL-ROOM outputs will be used to send the signal to studio monitor speakers.
41. FOOT SWITCH
This socket is used to connect an external foot switch. It has the same function as the FX MUTE switch.
42. AUX SEND
The AUX SEND output provides the signal of the AUX bus.
43. GR1/2 OUT
The GR1/2 SEND output provides the signals of the GROUP1/2 bus.
10
GIG-124CFX
Order code: D2285
44. PHONES
The PHONES output lets you plug in your headphones.
45. FX SEND
The FX SEND output provides the signal of the FX bus.
46. OPTIONAL MODULES SECTION
This section can be selected and installed according to the user's requirements. Open the cover and connect the module to connector CN6. The optional modules are: SMP-R, SMP-S, & Bluetooth-2.1. The signal for module playback can be assigned to Main Mix by 2TK routing. When using SMP-R recording function, the Cn12 needs to be connected. The signal comes from the Main Mix.
11
GIG-124CFX
Order code: D2285
A USB port: Allows the connection of any USB memory stick.
B PRE: Use this button to go back to the beginning of the current track or select a previous track for playing.
C NEXT: Use this button to skip to the next track.
D PLAY / PAUSE: Use this button to start playback. Press once to start playback, twice to set the pause mode and again to resume playback.
E STOP: Press this button to stop playback.
F DISPLAY: All the USB player information is monitored through this display.
Modules
Option One - SMP-S (Order code: D2290)
The file system should be FAT16 or FAT32. This player can only decode MP3. It has a maximum of 7 rank subordinate folders.
Operation Instruction for Song Module
A When no USB memory stick is inserted, the display will show Fig. 01 (see next page)
B Insert a USB memory stick, the USB player starts searching and the display shows "Searching". At
the end of the search, the display will show the menu as shown in Fig. 02 (see next page). By using the PRE / NEXT buttons, you can select one of following three menu options ("Playing", "Program" and "Folder List"). Press Playing, the unit will enter into the corresponding operation mode.
C "Playing" mode - single song play
1). In Fig. 02 (see next page), select Playing mode. This display shows the names of all the folders containing MP3 files. By using the PRE / NEXT buttons, you can scan the folders, then press PLAY / PAUSE. It will open the corresponding folder. Press STOP to return to Fig. 02 (see next page).
2). After opening the folder, the display will show Fig. 03 (see next page). This display shows the MP3 file list. You can scroll through the list by using the PRE / NEXT buttons. Choose the desired song. Press PLAY / PAUSE and the selected song playback will start. In order to stop playback, you just need to press the STOP button. Then, if you press PLAY / PAUSE, the song playback will start from the pause point, if you press again the STOP button, the system will return to Fig. 03 (see next page).
12
GIG-124CFX
Order code: D2285
Fig. 01
Fig. 02
Fig. 03
Fig. 04
Fig. 05
Fig. 06
Fig. 07
D "Program" mode
1) In Fig. 02, select "Program" to enter into the following interface: "Play list Set ": Set the play list. "Playing List": Play list. Press the PRE / NEXT buttons to select, press the STOP button to return the Fig. 02.
2) After entering the "Play List Set", the display will show as seen in Fig. 03. When selecting the desired folder, the display will show the following interface. The display will show all the MP3 files, the selected song will be inserted into the play list and a mark will appear. Press again and the song will be deleted from the play list and the mark will disappear. Press the
STOP button and you will return to Fig. 02. The play list can store up to 20 songs and it will
show the list according to song insert order.
3) The display will show the following interface. Press the PRE / NEXT buttons, you can select the starting song. Then press the PLAY/PAUSE button and the selected song playback will start. Press the PLAY / PAUSE button again or press STOP button, the play back will stop. Press the PLAY / PAUSE button again or press STOP button, the playback will start again from the same point. Press the STOP button twice, the USB player will return to Fig. 03.
E Folder List:
Fig. 03 shows the MP3 file folder names. Use the PRE / NEXT buttons to scan. Press the PLAY / PAUSE button to enter the corresponding folder. In order to return to Fig. 05, you just need to press the STOP button.
13
GIG-124CFX
Order code: D2285
A USB port: Allows the connection of any USB memory stick.
B PRE: Use this button to go back to the beginning of the current track or select a previous track for playing.
C NEXT: Use this button to skip to the next track.
D RPT: Use this button to repeat one track, one folder or all tracks. Repeat All: Plays the complete medium several times, the symbol on the screen is . Repeat: Repeats a single track several times, the symbol on the screen is . Play in order: play all the tracks in order, the symbol on the screen is blank. Random play: All tracks will be played back in random order, the symbol on the screen is A.
E PLAY / PAUSE: Use this button to start playback. Press once to start playback, twice to set the pause mode and again to resume playback.
F REC: Press this button to enable the recording preparation state. Press REC again to start recording. Any other operation is not available in the recording state, until POWER is pressed to stop recording.
G POWER(Push & Hold): When the power switch is pressed for 2-3 seconds, the device turns on.
H DISPLAY: All the USB player information is monitored through this display
Option Two - SMP-R (Order code: D2291)
The file system of USB memory for USB players is FAT16 and FAT32and these players can only decode MP3. It has a maximum of 7 rank subordinate folders.
14
GIG-124CFX
Order code: D2285
A DISPLAY These two LEDs are used to display different working states:
1) The first time the module is powered on, it is in stand-by state and the right LED flashes
twice for 2 seconds.
2) Matching state, two LEDs alternately flash quickly.
3) After connecting the device, the right LED lights up constantly.
B PRE: Use this button to go back to the beginning of the current track or select a previous track for playing.
C NEXT: Use this button to skip to the next track.
D VOL-: Press the VOL- button to decrease the volume. The default factory setting is maximum.
E VOL+: Press the VOL+ button to increase the volume.
F PLAY / PAUSE: Use this button to start playback. Press once to start playback, twice to set the pause mode and again to resume playback.
F REC: Press this button to enable the recording preparation state. Press REC again to start recording. Any other operation is not available in the recording state, until POWER is pressed to stop recording.
G PAIR: Press this button and hold for 2-3 seconds, the player will change to matching state. In this state, the two LEDs alternately flash quickly and you can use your mobile phone, tablet or PC Bluetooth adapter to find devices, BT-2.1. If your device's Bluetooth version lower than
2.0, you should enter the password "0000". If your device's Bluetooth version higher than 2.0, you do not need to enter a password.
Option Three - Bluetooth Version 2.1 (Order code: D2292)
Can be paired with mobile phones, tablets or PC Bluetooth adapters to play stereo audio.
15
GIG-124CFX
Order code: D2285
47. AC INLET WITH FUSE HOLDER
Before connecting the unit to the mains, ensure that the voltage setting matches your local voltage. Blown fuses should only be replaced by fuses of the same type and rating. To disconnect the unit from the mains, pull out the main cord plug.
48. POWER ON / OFF Use the POWER switch to turn on the mixing console. The POWER switch
should always be in the “Off” position when you are about to connect
your unit to the mains.
49. PHANTOM ON / OFF Phantom power is used for operating a capacitor microphone. As a rule, dynamic microphones can still be used with phantom power, provided they are wired in a balanced configuration.
Installation and connection
At this point you are in a position to successfully operate your GIG-124CFX Mixing Console. However, we advise you to carefully read the following section to be a real master of your own mixer. Not paying enough attention to the input signal level, to the routing of the signal and the assignment of the signal will result in unwanted distortion, a corrupted signal or no sound at all. So you should follow these procedures for every single channel:
Before connecting mics or instruments, make sure that the power of all your system components,
including the mixer, are turned off. Also, make sure that all the input and output controls are turned down. This will avoid damage to your speakers and avoid excessive noise.
Properly connect all external devices such as mics, power amplifiers, speakers, effect processor, etc. First, turn on the power of any peripheral devices, then power up the mixer. Set the output level of your mixer or the connected power amplifier at no more than 75%. Set the CONTROL ROOM/PHONE level at no more than 50%. Position HI, MID and LOW EQ controls on middle position. Position panoramic (PAN/BAL) control on center position. While speaking into the mic (or playing the instrument), adjust the channel level control so that the
PEAK LED will occasionally blink, in this way you will maintain good headroom and dynamic range.
You can shape the tone of each channel by adjusting the equalizer controls as desired. Now repeat the same sequence for all the input channels. The main LEDs can move up into the red
section, in this case you can adjust the overall output level through the MAIN MIX control.
16
GIG-124CFX
Order code: D2285
Headphone
Unbalanced
Balanced
Connection Cables
Take care of your cables, always holding them by the connectors and avoiding knots and twists when coiling them: This gives the advantage of increasing their life and reliability. Periodically check your cables. A great number of problems (faulty contacts, ground hum, discharges, etc.) are caused entirely by using unsuitable or faulty cables.
For these applications the unit provides 1/4" TRS and XLR connectors to easily interface with most professional audio devices. Follow the configuration examples below for your particular connection.
Unbalanced
Balanced
17
GIG-124CFX
Order code: D2285
Block Diagram
18
GIG-124CFX
Order code: D2285
No.
Preset
Description
Parameter
00~09
Echo
Reproduce the sound input on the output after a lapse of time or delay.
Delay Time: 145~205ms
10~19
Echo + Verb
Echo with Room effect.
Delay Time: 208~650ms Decay time: 1.7~2.1s
20~29
Tremolo
Amplitude modulation of the signal.
Rate: 0.6 Hz~5 Hz
30~39
Plate
Simulate the transducers sound like classic bright vocal plate.
Decay time: 0.9s~3.6s
40~49
Chorus
Recreate the illusion of more than one instrument from a single instrument sound.
Rate : 0.92Hz ~1.72Hz
50~59
Vocal
Simulate a small space with slight decay time.
Rev. decay time: 0.8~0.9s Pre-delay: 0~45ms
60~69
Rotary
Simulate the sound effect achieved by rotating horn speakers and a bass cylinder.
Modulation depth: 20%~80%
70~79
Small Room
Simulate a bright studio room.
Decay time: 0.7~2.1s Pre-delay: 20~45ms
80~89
Flanger + Verb
Simulate to play with another person carrying out the same notes on the same instrument and reverb.
Decay time: 1.5~2.9s Rate: 0.8Hz ~2.52Hz
90~99
Large Hall
Simulate a large acoustic space of the sound.
Decay time: 3.6~5.4s Pre-delay: 23~55ms
Preset List GIG-124CFX
19
GIG-124CFX
Order code: D2285
MODEL:
GIG-124CFX mixing console
Mono channels
Microphone input
XLR balanced
Frequency response
10Hz to 55KHz,+/-3dB
Distortion(THD+N)
<0.03% at +0dB ,22Hz~22KHz A-weighted
Gain range
0dB to 50dB
Max. Input
+15 dB
LOW CUT
100Hz
SNR
<-100dBr A-weighted
Phantom power
+48V with switch control
Line input
1/4' TRS balanced
Frequency response
10Hz to 55KHz,+/-3dB
Distortion(THD+N)
<0.03% at +0dB ,22Hz~22KHz A-weighted
Sensitivity range
+15dB~ -35dB
COMPRESSOR GAIN:0~9dB
THRESHOLD:20dB---> ↓5dB
Stereo input channels
Mic input
XLR balanced
LOW CUT
100Hz
Line input
1/4' TRS or TRS/RCA un-balanced
Frequency response
10Hz to 55KHz,+/-3dB
Distortion(THD+N)
<0.03% at +0dB ,22Hz~22KHz A-weighted
Sensitivity range
-20dBu~ +20dBu
SNR
<-100dBr A-weighted
Channels EQ
mono channel
stereo channel
High
+/-15dB@12KHz
+/-15dB@12KHz
Mid
+/-15dB@2.5KHz
+/-15dB@2.5KHz
Low
+/-15dB@80Hz
+/-15dB@80Hz
2-TRACK IN
TAPE IN
RCA jack
Frequency response
10Hz to 55KHz,+/-3dB
Distortion(THD+N)
<0.03% at +0dB ,22Hz~22KHz A-weighted
Gain range
OFF to 15dB
AUX RETURNS
Input
1/4' TRS un-balanced
Frequency response
10Hz to 55KHz,+/-3dB
Distortion(THD+N)
<0.03% at +0dB ,22Hz~22KHz A-weighted
GAIN range
OFF TO +15dB
SNR
<-100dBr A-weighted
Impedances
Microphone input
1.8K
All other input
10KΩ or greater
Tape out
1K
All other out
120
DSP section (options)
A/D and D/A converters
24bit
Type of effects Echo ,Echo+Verb, Tremolo, Plate, Chorus, Vocal
Rotary , Small Room , Flange + Verb , Large Hall
Controls Mute switch & Foot-switching with LED indicator
100 position preset selector(10 preseter * 10 variation)
FOOT-SW
TIP:FX
SLEEVE:GND
Main mix section
Max. MAIN MIX output
+22dBu XLR balanced (+16dBu un-balanced)
Technical Specifications
20
GIG-124CFX
Order code: D2285
AUX range
OFF to +15dB
Fader range
OFF to +10dB
PHONES/CONTROL-ROOM range
OFF to +15dB
Hum & Noise
<-80dB@20Hz~22KHz A-weighted 1 channel & MAIN level:0dB, the other: minimum
Crosstalk
<-80dB@0dB 20Hz~22KHz A-weighted MAIN level: 0dB, the other: minimum
Power supply
Main voltage
100-240V~ 50/60Hz
Fuse
T1.6A AC250V
Rated power consumption
40W
Design and product specifications are subject to change without prior notice.
Website: www.Dap-audio.info
Email: service@highlite.nl
21
GIG-124CFX
Order code: D2285
Dimensions
22
©2016 DAP Audio
Loading...