Danze DC023230, DC022221 Installation Manual [en, es, fr]
CALL 1-888-328-2383 OR VISIT WWW.DANZE.COM
© 2007 DANZE, INC. ALL RIGHTS RESERVED.
Español, página “Español - 1”
Français, page “Français - 1”
Installation Instructions
Cirtangular™ Collection
Two Piece Toilet
DC023230-DC022221
Pub No. IM-DC023230-DC022221/08-07.01
IntroductIon to danze
Thank you for choosing Danze. We believe that elements in your bathroom should
awaken your senses like a splash of cool water. That’s what you will experience
with Danze.
Danze is a manufacturer of high quality decorative plumbing products for your
powder room, kitchen and bath. We offer a broad variety of products, designs &
finishes to suit your own particular needs. You can feel confident that our products will provide years of beauty and trouble-free performance.
danze VItreous chIna Products
Danze vitreous china products include toilets, bidets and lavatories. Our fixtures
reflect state-of-the-art design and engineering, and meet or exceed the most
rigorous plumbing codes throughout North America. Operating fixtures are
equipped with first quality valves and accessories to give you years of troublefree service.
Should you have questions about your Danze purchase, contact us at our website
www.danze.com, or call our technical service center during business hours at
888-328-2383.
Danze, Inc. reserves the right to make product specification changes and to
change or discontinue models without notice or obligation in North America.
This toilet has been designed for easy installation. Conventional fittings have
been used throughout so that the working parts and operation of this assembly
may be easily understood. Local Plumbing and Building Codes should be followed for all installations.
Do not expose plastic trim parts to strong oxidizing agents, chlorine, or acid levels of lower than 5.0 pH. Most bowl/ tile cleaners contain such agents.
Tank type bowl cleaners can cause tank component failure and damage. Our warranty excludes such failures.
BeFore InstaLLatIon
Check to make sure you have the following parts included in the toilet tank
package:
( B ) Toilet Tank For Toilet Bowl Model DC023230 only
(M) Toilet Tank Cover
(Q) Toilet Tank assembly bag containing
( C ) Toilet Tank Mounting Bolts (2 each)
(D) Rubber Toilet Tank Bolt Washers (2 each)
( E ) Plastic Wing Nuts (4 each)
( F ) Toilet Tank to Bowl Gasket (1 each)
2
( G ) Channel Pads (2 each)
19”
5 3/4”
5
7/8”
2 3/8”
5/8”
12”
8”
6”
7
1/8”
15 1/4”
12 1/4”
3/8” S.P.S. SUPPLY
5 1/2”
SLOT (1/2”x1”)
8 3/4”
4 3/8”
29 1/4”
14 3/4”
18
1/2”
31
3/4”
16 1/2”
FINISHED
WALL
FINISHED
FLOOR
G
H
F
M
Q
O
N
C
D
E
A
B
( H ) Coupling Nut and Cone Washer (1 each)
( V ) Welcome to Danze kit
(W) Installation Instructions
( X ) Homeowner Care Manual
( Y ) Warranty Parts Guide
Check to make sure you have the following parts included in the toilet bowl
package:
( A ) Toilet Bowl For Toilet Tank Model DC022221 only
( N ) Toilet Seat
( O ) Ceramic Floor Bolt Cover Plates (2 each)
( V ) Welcome to Danze kit
( P ) Hook and Loop Tapes (6 strips)
(W) Installation Instructions
( X ) Homeowner Care Manual
( Y ) Warranty Parts Guide
Product dImensIons
tooLs requIred
Putty Knife Wax Ring (1 required) Floor Mounting Bolts,
* optional, only required if not already in place or the existing supply line needs to be replaced
Regular Screwdriver Safety GlassesCarpenter’s Level
Washers and Nuts
(2 each required)
Adjustable wrench
Flexible Water Supply Line*
InstaLLatIon InstructIons
1. Turn off and disconnect water supply. Unbolt
and remove old toilet. Remove old wax ring and
clean floor flange area with putty knife.
3
4
2. Install new wax ring (not included) on the bot-
tom of the toilet bowl (A) making sure not to
cover the toilet bowl outlet. (Alternate Method:
The wax ring may also be placed onto the floor
flange.)
3. Install the new floor mounting bolts (not included) upright in the slots of the floor flange.
Place the toilet bowl (A) over the floor flange/
waste line opening by aligning the floor mount-
ing bolts in the toilet floor bolt holes. Press
down firmly and twist toilet bowl (A) slightly to
compress wax ring and assure a seal between
the toilet bowl (A) and floor.
4. Place one floor mounting bolt washer (not
included) over each floor mounting bolt and as-
semble the floor mounting bolt nut to the floor
mounting bolt. Tighten floor mounting bolt
nut carefully until the floor mounting bolt nut
is just snug.
5. Install the ceramic floor bolt cover plates (O)
(included) by firmly pressing the ceramic floor
bolt cover plates (O) into the recesses in the side
wall of the toilet bowl (A). (Six additional strips
of hook and loop tape (P) are provided should
replacements be needed in the future.)
7. Assemble toilet tank mounting bolts (C) in toilet tank (B) with rubber toilet tank bolt washers
(D) and plastic wing nuts (E). Plastic wing nuts
(E) should be tightened by hand sufficiently to
compress rubber toilet tank bolt washers (D) and
insure water seal.
8. Assemble toilet tank to bowl gasket (F) to
flush valve shank so that lock nut is enclosed in
recess, making sure that the entire surface of the
toilet tank to bowl gasket (F) is in contact with
the toilet tank bottom.
9. Place two channel pads (G) onto the posts on
back of toilet bowl ledge to prevent china-tochina contact.
10. Place toilet tank assembly in position. Tighten the plastic wing nuts (E) sufficiently by hand
to prevent rocking. Since the toilet tank mounting bolts (C) are already sealed, the toilet tank
(B) can be leveled by the relative amount that
each plastic wing nut (E) is pulled down on the
three points of contact- toilet tank to bowl gasket (F) and two channel pads (G).
11. The fill valve coupling nut (H) is provided to
connect the water supply line to the fill valve.
6. Before assembling toilet tank (B) to toilet
bowl (A) check tightness of lock nuts on both
flush valve and fill valve.
5
Do not use pipe dope! Hand tightens only!
Over tightening may split the fill valve and will
void the warranty.
6
Loading...