Dansons Group V-200, V-50 User Manual

Dear VULCAN “V” SERIES Pellet Stove Owner:

CONGRATULATIONS on the purchase of your VULCAN “V” SERIES wood pellet appliance! You have selected the finest in residential wood pellet heating technology.

Let us pass on a few "tips" concerning installing your stove and heating with wood pellets.

1. Whether you install your stove yourself or hire a professional installer, a quality installation is a must for the safety of your family and for efficient, satisfactory operation of your stove.

2. Initial Burn Setup of the stove is the most important step to ensure the efficient and satisfactory

operation of your appliance for many years to come.

3. Know the quality and characteristics of the pellets you burn. Pellets can vary greatly from company to company, from load to load and occasionally from bag to bag.

4. Be extra diligent in your cleaning program.

5. Remember that most operational dilemmas with a pellet stove are usually traced back to Improper installation, poor quality pellets and/or a lack of timely cleaning.

With just a minimum of daily care your VULCAN “V” SERIES pellet appliance will provide years of clean, efficient, comfortable and environmentally sound heating.

Thank you for selecting a VULCAN “V” SERIES wood pellet appliance.

Sincerely,

Canadian Comfort Industries & Dansons Group Inc.

UPDATES and REGISTRATION

Up to date additions, product information, product registration and warranty extension registration can be found on

our website www.dansons.com/support

No part of this manual may be copied, transmitted, transcribed, stored in a retrieval system, in any form or by any means without the expressed written permission of,

Canadian Comfort Industries; 26319 Twp Rd 531, Acheson, AB, Canada T7X 5A3

Canadian Comfort Industries V05 2 VULCAN “V” SERIES OWNERS MANUAL

Dansons Group Inc.

TABLE OF CONTENTS

GENERAL INFORMATION

SAFETY PRECAUTIONS --------------------------------------------------------------------- SAFETY TESTING --------------------------------------------------------------------- HOW YOUR VULCAN “V” SERIES STOVE WORKS --------------------------------- AUTOMATIC SAFETY FEATURES ---------------------------------------------------------- SPECIFICATIONS ------------------------------------------------------------------------------

INSTALLATION

INSTALLATION PLANNING & CHECK LISTS ----------------------------------------- INSTALLATION OPTIONS ------------------------------------------------------------------ EXHAUST SYSTEMS -------------------------------------------------------------------------- SIZING ----------------------------------------------------------------------------------------- TERMINATION ------------------------------------------------------------------------------ CLEARANCES ------------------------------------------------------------------------------- OUTSIDE AIR ------------------------------------------------------------------------------------ FREESTANDING INSTALLATION STOVE PLACEMENT ---------------------------------------------------------------------- FLOOR PROTECTION --------------------------------------------------------------------- CLEARANCES ------------------------------------------------------------------------------ ALCOVE ---------------------------------------------------------------------------------------- THROUGH THE WALL DIRECT INSTALLATION --------------------------------- VERTICAL INSTALLATIONS ------------------------------------------------------------ MOBILE HOME INSTALLATION ------------------------------------------------------------- INSERT / BUILT-IN INSTALLATION IN A WOOD OR COAL BURNING FIREPLACE ------------------------------------ IN A WALL OR MANTEL -------------------------------------------------------------------

OPERATION

LIGHTING A FIRE ------------------------------------------------------------------------------ THE ACUTRON CONTROLS ---------------------------------------------------------------- SHUTTING THE STOVE OFF --------------------------------------------------------------- ACUTRON WALL THERMOSTAT (OPTIONAL) --------------------------------------- INITIAL BURN SETUP ------------------------------------------------------------------------- PERFORMANCE ENHANCEMENT TIPS -------------------------------------------------

PELLETS

PELLET QUALITY ----------------------------------------------------------------------------- PELLET CONSUMPTION -------------------------------------------------------------------- FACTORS EFFECTING PELLET FEED RATES -------------------------------------- FINE TUNING THE PELLET FEED RATES --------------------------------------------- ASH and CLINKERS -------------------------------------------------------------------------- FINES -------------------------------------------------------------------------------------------- PFI PELLET STANDARDS -------------------------------------------------------------------

MAINTENANCE

INSERTING, REMOVING, AND ADJUSTING THE BURN GRATE --------------- REQUIRED CLEANING ----------------------------------------------------------------------- PERIODIC MAINTENANCE ------------------------------------------------------------------ TROUBLE SHOOTING -------------------------------------------------------------------------

LIMITED WARRANTY ------------------------------------------------------------------------- APPENDIX “A” - VULCAN “V” SERIES OPTIONS -----------------------------APPENDIX “B” – VULCAN “V” SERIES ACCESSORIES --------------------SERVICE LOG ----------------------------------------------------------------------------

4,5

5 6 7 8

9 10 11 11 12 12 13

14 14 14 15 16 17 18

19 21

23 24 25 26 27 28

29 29 29 29 30 30 30

31 32

33 35 36 37

38 40

adian Comfort Industries V05 3 VULCAN “V” SERIES OWNERS MANUAL

Can

Dansons Group Inc.

SAFETY PRECAUTIONS

IMPORTANT: Read, save and follow the instructions in this manual. It contains important Safety, Operating and Maintenance instructions you will need.

• BEFORE installing or having the pellet appliance installed contact the local building officials to obtain the necessary permits and information on any installation restrictions or inspection requirements in your area and notify your insurance company you have installed a pellet appliance.

• This unit must be properly installed to prevent the possibility of a house fire. The instructions and local building codes requirements must be strictly adhered to. Do not; use makeshift methods or material that may compromise the installation.

• When the pellet appliance is installed in a mobile home, the heater must be bolted to the floor, have outside air, and MUST NOT BE INSTALLED IN THE BEDROOM (Per H.U.D. requirements). Check with local building officials.

• NEVER try to repair or replace any part of the heater unless instructions for consumer are given in this manual or instructed by Dansons Customer Service Department. A trained technician should do all other work.

• Educate all children of the danger of a high-temperature heater. Young children should be supervised when they are in the same room as the heater.

• This heater is designed and approved for pelletized wood fuel only. Any other type of fuel burned in this heater will void the warranty and safety listing. Keep foreign objects out of the hopper.

• NEVER use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or “freshen up” a fire in this appliance. Keep all such liquids well away from the appliance while it is in use.

• This heater must be connected to a standard 115 V., 60 Hz grounded electrical outlet. A grounded surgeprotection unit is recommended.

• Do not use an adapter plug or sever the grounding prong on the electrical plug.

• Do not route the electrical cord underneath, in front of, or over the heater.

• Do not unplug the stove if you suspect a malfunction. Push the “OFF” Touch Pad and inspect the heater.

• The heater will not operate during a power outage. If a power outage does occur, check the heater for

smoke spillage and open a window if any smoke spills into the room.

• DO NOT operate the heater if you smell smoke coming from the heater. Push the “OFF” Touch Pad, monitor your pellet appliance, and call your local authorized dealer.

• Do not place clothing or other flammable items on or near the heater. When installed with a thermostat there is a possibility of the heater turning on and igniting any items placed on or near the unit.

• CAUTION: NEVER put fingers in or near pellet feed auger. The pellet fuel is fed to the burn pot by a screw auger that is driven by a high torque motor. This auger can start and stop anytime automatically without warning while stove is operating.

adian Comfort Industries V05 4 VULCAN “V” SERIES OWNERS MANUAL

Can

Dansons Group Inc.

SAFETY PRECAUTIONS . . . Continued

• DO NOT operate the stove if the flame becomes dark and sooty or if the firepot overfills with pellets. Push the OFF Touch Pad and inspect the heater. (See Operating Your Stove). Soot or creosote may accumulate in the exhaust vent system when the stove is operated under incorrect conditions such as an extremely rich burn. The flame will have a lazy orange color with black tips. This indicates poor pellet fuel combustion.

• NEVER block free airflow through the open vents of the unit. The viewing door and ash pan must be closed and latched during operation.

• The pellet appliance exhaust system works with negative combustion chamber pressure and a positive chimney pressure, therefore the exhaust system must be completely airtight and properly installed. All exhaust system vent joints must be sealed, gas tight, with HI-TEMP RTV silicone sealant, and/or at least 3 sheet metal screws per joint and to the heater also.

• Your heater requires periodic maintenance and cleaning (Refer to ”Routine Cleaning” section of the manual). Failure to maintain your heater may lead to smoke spillage in your home.

• Disconnect the power cord from the electrical outlet before performing any maintenance. Pushing ”OFF” Touch Pad does not disconnect all power to the heater.

• BEFORE carrying out any maintenance or cleaning, allow the heater to cool. Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface or on the ground, well away from all combustible materials, pending final disposal.

• The exhaust system should be checked twice a year minimum for any build-up of soot or creosote. Do not touch the hot surfaces of the heater.

Note: Canadian Comfort Industries grants no warranty, implied or stated, for the installation or maintenance of your heater, and assumes no responsibility of any consequential damage(s).

SAFETY TESTING

In accordance with the procedures and specifications listed in UL1482 – 1998 & ASTM E 1509-95, and ULC-S627-00 and ULC-S628-M93 for solid fuel room heater, the Canadian Comfort Industries pellet stove has been independently tested and listed by I.T.S. (an accredited testing laboratory) to UL, ULC and CSA standards. It is tested and listed for residential installation according to current national and local building codes as:

• A Freestanding Room Heater

• A hearth insert when installed into a masonry or factory built fireplace.

• A Mobile Home Heater.

• A Built-In Heater.

The Safety Listing Label is located on the rear inspection panel for model FPP and on the side panel for model IPP. Please read the label carefully. It contains important information about installation and operation of your pellet appliance. Note that your STOVE’S serial number is located on the safety label. Your appliance serial number is preceded by a “WH-“ (example WH-00000)

adian Comfort Industries V05 5 VULCAN “V” SERIES OWNERS MANUAL

Can

Dansons Group Inc.

HOW YOUR STOVE WORKS

The operations and maintenance of your VULCAN “V” SERIES stove are unique and should not be considered to be like a wood, coal stove, gas, electric, propane or oil heater.

Cautions:

Do not try to operate your stove with viewing door open. Pellets will not feed under these circumstances and a safety concern may arise from sparks or fumes entering room.

Burn only pellet fuel that complies with PFI standards. Burning other types of fuels may result in the formation and leakage of Carbon Monoxide which if undetected can be deadly.

If you are not drawing combustion air from outside, care must be taken to allow for adequate air make up, to avoid possible room air starvation when stove or other exhaust fans are in operation.

It is recommended that you install a high quality smoke detector in the room where stove is installed.

Fuel in the form of wood pellets is stored in the hopper. An auger delivers the pellets to the burn grate. The fuel rate, or heat output, is set by adjusting the feed rate touch pad, (settings 1 to 4). A fan provides combustion air to the burn grate. The amount of combustion air in the burn grate is adjustable and automatically changes as the fuel rate changes. The higher the fuel rate, the larger the amount of combustion air and visa versa. The fuel burns in the burn grate, producing heat. Some heat radiates out the front of your stove. The majority of the heat passes around the heat exchange tubes and air plenum around the firebox and is then moved into the room by the room air fan. A small amount of heat must pass out the exhaust of your stove, along with gases, into the atmosphere.

Care should be taken to make sure detector is in working order at all times.

Your stove's heat output can be adjusted from setting 1-4, through the FEED RATE touch pad, to vary your heat output from Low to High. The room air fan can be manually adjusted through the FAN SPEED to run faster or slower to correspond to the amount of heat being produced. The room air fan is also on a limit switch, controlled to run on high when the stove reaches higher temperatures and then resume the speed you had selected once it cools to a lower temperature.

Your stove can run efficiently over extended periods of time and at different heat output levels as long as the fuel supply is uninterrupted and timely cleaning and maintenance is performed. An example of how improper cleaning effects operations is; the exhaust pressure switch will shut the pellet supply off and your stove will shut off if the exhaust system becomes plugged.

Heat Tubes

Tube Scraper

Hopper

Auger

Window

Auger Motor

Fan Motors

Exhaust

Burn Pot

Air Intake

“Super” Grate

(Optional)

Pedestal

adian Comfort Industries V05 6 VULCAN “V” SERIES OWNERS MANUAL

Can

Dansons Group Inc.

AUTOMATIC SAFETY FEATURES

L120 LOW LIMIT SWITCH

This limit switch is mounted on the exhaust blower housing and has 2 main functions.

1. Should the fire happen to go out, for any reason, this limit switch will shut the stove off when the exhaust temperature drops below 120deg F.

2. Upon starting the appliance, the AcuTron control board has a 15 minute “Lighting Mode”, if the stove exhaust does not reach 120deg F in that 15 minutes the stove will shut off. As soon as the stove exhaust does reach 120deg F, the limit switch opens and the

F140 FAN LIMIT SWITCH

Your pellet appliance has a convection fan control limit switch. The room air fan's (F140) temperature limit snap switch automatically sets the fan on high when your stove is producing heat faster than the fan is carrying it into the room. This may occur when the heat control lever is set at [3 or 4] and the FAN SPEED is set to a very low or off setting. After the fan runs at this automatic high setting a few minutes, it may cycle back to its lower setting and may continue to cycle between [HIGH] and your selected setting. The circulation (room air) fan cycling from high to low is a normal condition as well as a safety feature of your appliance. To compensate for the fan cycling, adjust the FAN SPEED to a higher setting.

L250 HIGH LIMIT SWITCH

Your pellet appliance has a high temperature limit switch installed. If the temperature at the back of the firebox reaches approximately 250deg F., the switch will shut off the electricity going to the Vacuum Switch and to the Auger Motor. The auger will automatically stop, and the appliance will shut down when the exhaust temperature cools (120deg F). If this happens call your dealer or Dansons Customer Service (1-866-456-9269).

IT IS IMPORTANT TO FIND THE REASON WHY THE UNIT OVERHEATED.

VACUUM SWITCH

This safety device (mounted on the back panel pillar) detects vacuum in the exhaust system, firebox, and air intake. If the exhaust blower fails, the vent pipe becomes plugged, the viewing door is open, or if you are out of pellets, this switch will sense that there is a lack of vacuum and will stop the auger from continuing to feed pellets.

If the power does go out, the pellet appliance will stop running. When the power comes back on, the stove will not restart if the switch is in the manual mode. If the exhaust temperature is above 120deg F or the switch is in the manual position, the stove will start to feed pellets again and may relight itself.

NOTE: If power outages are a concern you may wish to purchase a back-up generator system. For further information contact your local Specialty Retailer, Certified HVAC Service Depot, or Dansons

Group Inc. Customer Service Department at 1-866-456-9269.

AcuTron enters a 5 minute “Safety Delay” mode.

adian Comfort Industries V05 7 VULCAN “V” SERIES OWNERS MANUAL

Can

Dansons Group Inc.

SPECIFICATIONS

HEATING SPECIFICATIONS

Approx. Heating capacity (sq. feet) * 800 – 2,000 Approx. Fuel burn rate per hour ** 1.5 – 5 lbs Hopper Capacity - Traditional Stove / Insert 40 lbs Approx. Burn time at lowest setting 27 hrs Hopper Capacity – Bay View Free Standing 60 lbs Approx. Burn time at lowest setting 48 hrs Hopper Capacity – Bay View Insert / Built-In 40-60 lbs Approx. Burn time at lowest setting 27-48

* Heating capacity will vary depending on floor plan layout of your home, degree of insulation, and the outside temperature. Fuel size, quality, density and moisture level will also have an effect. ** Pellet size may effect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as much as 20%. Use

PFI listed fuel for best results.

DIMENSIONS

adian Comfort Industries V05 8 VULCAN “V” SERIES OWNERS MANUAL

Can

Dansons Group Inc.

PLANNING & INSTALLATION CHECK LIST

Unless you are knowledgeable and experienced in stove installation, we recommend your VULCAN “V” SERIES stove receive a Pre-delivery Check and be installed by your local Specialty Retailer or Certified HVAC Service Depot.

COMPLETE THIS CHECK LIST PRIOR TO INSTALLING YOUR PELLET APPLIANCE:

_____ Carefully read this "Owner's Manual”. SAVE THIS MANUAL.

_____ Have your local Dealer demonstrate all the operational, cleaning and maintenance steps necessary

_____ Select a location. The design of your home and the stove placement will determine its value as a

Existing Chimneys, Pellet Fuel Storage, Aesthetic Considerations, Roof Design (rafter

_____ The installation of this appliance must conform to local codes and applicable state and federal

_____ Sign and keep a copy of the Pre-delivery Check List supplied by your Authorized VULCAN “V”

______ Register your purchase online at www.dansons.com/support.

COMPLETE THIS CHECK LIST WHILE INSTALLING YOUR PELLET APPLIANCE:

_____ Carefully read the ENTIRE installation section first.

_____ Read the Freestanding or Insert or Built-In section (which ever applies)

_____ Determine the location and measurement needed your chosen location.

_____ Be sure to pre-fit all items before you install, fasten or install the stove permanently. Remember

_____ Ensure ALL joints of “PL” vent and single wall stainless steel liner are tightly connected, sealed

COMPLETE THIS CHECK LIST PRIOR TO LIGHTING YOUR FIRST FIRE:

_____ Obtain final inspection and approval by local building officials.

_____ Carefully clean all marks off the brass, nickel or pewter parts before the first fire is lit. Use a soft cloth

_____ Polish the hopper to remove the oil type coating used in manufacturing.

_____ The high temp. stove paint used on your stove may take several hours of burning at a high fuel setting to

_____ Review and follow the Lighting and Controls Instructions.

_____ Fill the hopper with quality pellets to prime the unit; Using the CCI “AcuTron”, (figure 5), PUSH the

for your stove.

source of heat. A pellet appliance depends primarily on air circulation to disperse its heat. There are other practical considerations, which must be considered before a final placement is decided on:

locations & roof pitch), Room Traffic, Clearances to Combustibles, and Existing Wiring.

requirements. Becoming familiar with these requirements before installation is essential.

SERIES Dealer, OR “Dansons Certified Installer”, found inside our appliance or available online. Register online at www.dansons.com/support

for Extended Warranty.

measure twice, cut once.

with RTV Silicone, including to the exhaust connector, and is correctly installed. (Follow vent

manufacturer’s instructions.)

and a gentle type cleaner. Caution: Never use an abrasive cleaner on any part of your stove.

fully cure. During this time an odor, which is not harmful, may be evident. The area around the stove should be well ventilated.

FEED RATE Touch Pad and this will start the auger and the combustion fan.

adian Comfort Industries V05 9 VULCAN “V” SERIES OWNERS MANUAL

Can

Dansons Group Inc.

INSTALLATION OPTIONS

READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR

VULCAN “V” SERIES HEATER. FAILURE TO FOLLOW INSTRUCTIONS MAY

RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH!

(See specific Installation details for clearances and other installation requirements)

The two VULCAN “V” SERIES models are the: “FPP” Freestanding: a Traditional styled stove mounted on a pedestal (figure 1) or Leg platform (figure 2), and a Bay View style(figure 3); and the “IPP” Fireplace Insert / Built-In: a Traditional style (figure 4), and a Bay View style (figure 5). Both models are available in black, pewter or gold plated doors, legs, and louvers.

All models may be installed to code in both conventional and mobile homes.

INSTALLATION OPTIONS INCLUDE:

1. A FREESTANDING STOVE: Set on a pedestal or legs and placed on a non-combustible floor pad. (figure 1,2 & 3)

2. An ALCOVE: Set on a pedestal and placed on a non-combustible floor pad in compliance with clearance requirements for an installation in an alcove.

3. A HEARTH STOVE: When installed with or without a pedestal on a non-combustible hearth of a masonry or factory built wood or coal burning fireplace.

4. A FIREPLACE INSERT: When installed, with a shroud, in a masonry or a factory built, wood or coal burning fireplace.

(figure 4 & 5)

5. A BUILT-IN INSERT: When installed on a non-combustible pad, in a wall or custom built mantel and where adequate airflow around the stove is provided. (figure 4 & 5)

(figure 1, 2 & 3)

(figure 1,2 & 3)

adian Comfort Industries V05 10 VULCAN “V” SERIES OWNERS MANUAL

Can

Dansons Group Inc.

EXHAUST SYSTEMS (GENERAL)

PELLET VENT MUST MAINTAIN A MINIMUM 3” CLEARANCE TO ANY COMBUSTIBLE

(INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER).

DO NOT CONNECT THE PELLET VENT TO A VENT SERVING ANY OTHER APPLIANCE

OR STOVE.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.

PELLET VENT TYPE:

Must be an approved 3” or 4” Diameter Type ”PL” vent, vented to the outside (fig. 7) or connect the vent to a factory built type “A” chimney using an adaptor; and/or “All Fuel” Stainless Steel chimney liner for masonry fireplace installations (fig. 8) . Use 4” dia. vent if vent or liner height is over 15’ or if installation is over 4,000’ above sea level.

MAXIMUM VENTING SIZE:

Max imum ventin g he ight is 33’. Maximum horizontal offset is 10’. Use no more than 18 0 of elbow s (two 90 elbows, or two 45 elbows & one 90 elbow, et c), plus termination.

Vent must have a support bracket every 5’ when on the exterior wall.

If appliance is installed above 4,000’ elevation, always use 4” diameter venting.

4”

Use Diameter “PL” Vent If venting outside of shaded area.

3” 4”

Use or Diameter “PL” Vent, if venting in shaded area.

33’

30’

25’

20’

15’

Vent height and run

exceed the distance

not

shown in the un-shaded region of chart.

To achieve optimum performance, keep vent runs as short as possible. Esp ecial ly on horizont al installations.

must

10’

5’

0’

5’

10’

VENT INSTALLATION:

Termination must exhaust above the air inlet elevation, and parallel or above the exhaust output of the pellet appliance. It is recommended that at least 3’ of vertical pipe be installed to create some natural

Can

draft. This is to help prevent the possibility of smoke or odor during the appliance shut down.

Horizontal sections must have a ¼” rise every 12” of travel after 3’ long.

Pellet Vent connections must be sealed with HI-Temp RTV Silicone and screwed together with at least 3 x 3/8” long stainless steel screws. Seal each vent section by injecting a liberal amount of HITEMP RTV silicone sealant into the gap.

adian Comfort Industries V05 11 VULCAN “V” SERIES OWNERS MANUAL

Dansons Group Inc.

EXHAUST SYSTEMS . . . Continued

PELLET VENT TERMINATION: (Figures 7 & 8)

Termination must be a minimum of 6” above the chimney (B) (note: the chimney must meet local codes for height above the roof or other obstructions)

Must have an approved cap (to prevent water from entering) or a 45* elbow downturn

If the termination is located on a windy side of house, an approved house shield is recommended to prevent soot from accumulating on the side of the house.

Must not be located where snow or other materials will plug it.

Must have a “Metal Seal Plate” or “Wall Thimble” at point (A)

Figure 7 Figure 8

VENT TERMINATION CLEARANCES:

• Horizontal terminations must protrude 12” from the wall, vertical terminations 24”

A Minimum 4’ clearance below or beside any door or window which opens. B Minimum 1’ clearance above any door or window that opens. C Minimum 3’ clearance from any adjacent building. D Minimum 7’ clearance above any grade when adjacent to public walkways.

NOTE: Vent may not terminate in covered walkway or breezeway. E Minimum 2’ clearance above any grass, plants, or other combustible material. F Minimum 3’ clearance from any forced air intake of any other appliance. G Minimum 2’ clearance below eves or overhang. H Minimum 1’ clearance horizontally from combustible wall X Must be a minimum of 36” above the roof and 24” above the highest point of the roof within 10’.

3’

10’

Figure 9

adian Comfort Industries V05 12 VULCAN “V” SERIES OWNERS MANUAL

Can

Dansons Group Inc.

+ 28 hidden pages

Dansons Group V-200, V-50 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual