Danfoss TL4GH Data sheet

TL4GH

Heat Pump Compressor

R134a

220-240V 50/60Hz

General

Code number						102G4455
Approvals				EN 60335-2-34, UL984
Compressors on pallet						125
Application
Application						HBP
Frequency		Hz		50					60
Evaporating temperature		°C	-15 to 15					-15 to 15
Voltage range		V	198 - 254					198 - 254
Max. condensing temperature continuous (short)		°C		60 (70)				60 (70)
Max. winding temperature continuous (short)		°C	125 (135)					125 (135)
Cooling requirements
Frequency		Hz		50					60
Application			LBP		MBP	HBP		LBP	MBP	HBP
32°C			–		–	F2		–	–	F2
38°C			–		–	F2		–	–	F2
43°C			–		–	F2		–	–	F2
Remarks on application:
Motor
Motor type						CSIR
LRA (rated after 4 sec. UL984), HST | LST		A		5.7					–
Cut in Current, HST | LST		A		5.7					–
Resistance, main | start winding (25°C)		Ω		14.5					14.8
Design
Displacement		cm3				3.86
Oil quantity (type)		cm3			280 (polyolester)
Maximum refrigerant charge		g				600
Free gas volume in compressor		cm3				1690
Weight without electrical equipment		kg				7.5
Dimensions
Height		mm	A			173
			B			169
			B1				–
			B2				–
Suction connector	location/I.D. mm | angle		C			6.2 | 30°
	material | comment			Cu-plated steel | Al cap
Process connector	location/I.D. mm | angle		D			6.2 | 31.5°
	material | comment			Cu-plated steel | Al cap
Discharge connector	location/I.D. mm | angle		E			5.0 | 28°
	material | comment			Cu-plated steel | Al cap
Oil cooler connector	location/I.D. mm | angle		F				–
	material | comment						–
Connector tolerance	I.D. mm		±0.09, on 5.0 +0.12/+0.20
Remarks:

S

= Static cooling normally sufficient

O

= Oil cooling

F1

= Fan cooling 1.5 m/s

(compressor compartment temperature

equal to ambient temperature)

F2

= Fan cooling 3.0 m/s necessary

SG

= Suction gas cooling normally sufficent

–= not applicable in this area

Dec 2011

Manufactured by Secop for Danfoss - DEHC.ED.400.P7.02 / 520N1220

1/2

EN 12900 Household (CECOMAF)					220V, 50Hz, fan cooling F2
Evap. temp. in °C	-45	-40		-35	-30		-25		-23.3				-20	-15	-10	-6.7	-5		0	5	7.2	10	15	20
Capacity in W														104	140	167	182		230	287	315	353	429
Power cons. in W														109	121	129	134		146	159	164	171	181
Current cons. in A														0.97	1.01	1.03	1.05		1.09	1.12	1.14	1.16	1.20
COP in W/W														0.96	1.16	1.29	1.36		1.57	1.81	1.92	2.07	2.37
EN 12900 Household (CECOMAF)					220V, 60Hz, fan cooling F2
Evap. temp. in °C	-45	-40		-35	-30		-25		-23.3				-20	-15	-10	-6.7	-5		0	5	7.2	10	15	20
Capacity in W														118	160	191	208		264	328	360	403	489
Power cons. in W														123	139	150	156		174	193	202	213	232
Current cons. in A														0.89	0.95	1.00	1.02		1.09	1.16	1.19	1.23	1.31
COP in W/W														0.96	1.15	1.27	1.33		1.51	1.70	1.78	1.90	2.11
ASHRAE HBP					220V, 50Hz, fan cooling F2
Evap. temp. in °C	-45	-40		-35	-30		-25		-23.3				-20	-15	-10	-6.7	-5		0	5	7.2	10	15	20
Capacity in W														129	173	206	225		285	356	391	439	535
Power cons. in W														109	121	129	134		146	159	164	171	181
Current cons. in A														0.97	1.01	1.03	1.05		1.09	1.12	1.14	1.16	1.20
COP in W/W														1.18	1.43	1.60	1.68		1.95	2.24	2.38	2.57	2.95
ASHRAE HBP					220V, 60Hz, fan cooling F2
Evap. temp. in °C	-45	-40		-35	-30		-25		-23.3				-20	-15	-10	-6.7	-5		0	5	7.2	10	15	20
Capacity in W														146	198	236	257		327	408	447	501	609
Power cons. in W														123	139	150	156		174	193	202	213	232
Current cons. in A														0.89	0.95	1.00	1.02		1.09	1.16	1.19	1.23	1.31
COP in W/W														1.19	1.43	1.57	1.65		1.88	2.11	2.22	2.36	2.63

Accessories for	TL4GH	Figure	Code number
PTC starting device	6.3 mm spade connectors	a1	–
	4.8 mm spade connectors		–
Starting relay	6.3 mm spade connectors	a2	117U6000
Start. capacitor 60 µF	6.3 mm spade connectors	c	117U5014
Cover		b	103N2011
Cord relief		d	103N1010
Protection screen for PTC		g	–

Test conditions	EN 12900/	ASHRAE
	CECOMAF	HBP
Condensing temperature	55°C	55°C
Ambient temperature	32°C	32°C
Suction gas temperature	32°C	32°C
Liquid temperature	55°C	32°C

Mounting accessories			Code number
Bolt joint for one comp.	Ø: 16	mm	118-1917
Bolt joint in quantities	Ø: 16	mm	118-1918
Snap-on in quantities	Ø: 16	mm	118-1919

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.

All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

2/2

Manufactured by Secop for Danfoss - DEHC.ED.400.P7.02 / 520N1220

Dec 2011