Danfoss SV10-35-02 Technical Information
Solenoid Valves Technical Information
5 Way, 3 Position Spool
SV10-35-02
OPERATION
This is a direct acting, 3-position, 5-way spool type solenoid valve. When
de-energized, the SV10-35-02 blocks ow at all ve ports. When coil S1 is energized,
the spool shifts to allow ow from port 5 to port 4 (with load sense reference to
port 1) and port 2 to port 3. When coil S2 is energized, the spool shifts to allow ow
from port 5 to port 2 (with load sense reference to port 1), and from port 4 to 3. The
SV10-35-02 comes standard with a one-direction, push-pin manual override. When
the manual override is pushed, the spool shifts following the logic of energizing S2.
APPLICATIONS
The SV10-35 family is designed to control the direction of ow in load sensing
systems. Having the load sense port integrated into the spool eliminates the
need for check and/or shuttle valves between the SV10-35 and the work function.
It is recommended to apply an orice or ow regulator to bleed down the
signal, if this feature is not included in the pump. Apply a check or shuttle valve
at port 1 for your load sense signal. With a 02-spool, in the center position, work
ports are blocked. In load holding applications, pilot to open check or counter
balance valves are recommended. When controlling a cylinder, the base or cap
end can be connected to either ports 2 or 4, providing symmetrical metering.
For use with the PAP override, load sense pressure must be limited to 150 bar.
SPECIFICATIONS SCHEMATIC
Rated Pressure* 230 bar [3330 psi]
Maximum Rated Flow at 7 bar
[100 psi]
Weight including coil 0.9 kg [1.98 lbs]
Cavity SDC10-5
Standard Coil M16 26 Watt
Robust Coil R16 20 Watt
* Rated Pressure based on NFPA fatigue test standards (at 1 Million Cycles).
18 l/min
[4.8 US gal/min]
Robust Nut P/N 173804910
(no coil O-rings needed)
Shown with Standard Coils,
Deutsch Connectors
2
S2
53
4
S1
1
PERFORMANCE CURVES
25
20
15
10
5
0
0
Pressure drop
20 30 4010
4
2
6
5-4
8
4-3
10
5-2
2-3
l/min
US gal/min
26 cSt [121 SUS] hyd.oil at 50°C [122 °F]
psi
bar
350
280
210
140
70
0
BC332375861112en-000101 • February 2020
psi
3500
3000
2500
2000
1500
1000
500
Operating envelope
bar
240
210
180
S2 Energized
150
120
90
60
30
0
0
0
10 403020
2
4
S1 Energized
6
8
10
l/min
US gal/min
SV - 227
Solenoid Valves Technical Information
[Ø1.04]
5 Way, 3 Position Spool
SV10-35-02
DIMENSIONS
mm [in]
EXAMPLE CIRCUITS
24 mm
9-11 Nm
[80-97 lbf*in]
Coil Nut Kit P/N 17400031
S2
COIL NOT SHOWN FOR CLARITY
INSTALL O-RING (4) PLCS AS SHOWN
Cross-sectional view
45-50 Nm [33-37 lbf*ft]
27 mm
S1
[0.20]
205.3
[8.08]
5.0
1
Ø26.5
LS
T
P
B
5
4
78.0
[3.07]
A
3
2
ORDERING INFORMATION
SV10-35-02-12D-DE-PB-B-00
Solenoid Valve
3 position, 5 way, 10-Size.
Coil voltage
00 = No Coil
12 VDC
24 VDC
Coil termination
Description
No Coil
Flying Lead
Deutsch
AMP SuperSeal 1.5
Amp Junior
Metri-Pack 150 Type 2
Flying Lead with Diode
Deutsch with Diode
AMP SuperSeal with Diode
Amp Junior with Diode
Metri-Pack 150 with Diode
DIN 43650
Standard Coil
00
12D
24D
Robust Coil
Standard
Coil Code
00
FL
DE
AS
AJ
-
FLD
DED
ASD
AJD
-
DN
00
R12D
R24D
IP
Rating
IP65
IP69K
IP67
IP67
IP65
IP69K
IP67
IP67
IP65
BC332375861112en-000101 • February 2020
-
-
-
Robust
Coil Code
00
FL
DE
AS
- -
M3
FLDB
DEDB
ASDB
-
M3DB
-
IP
Rating
-
IP69K
IP69K
IP69K
IP69K
IP69K
IP69K
IP69K
IP69K
Housings
Code
Ports & Material
00
Cartridge Only
6S
#6 SAE, AL
#8 SAE, AL
8S
S8S
#8 SAE, Steel
3/8 BSP, AL
L3B
L4B
1/2 BSP, AL
S4B
1/2 BSP, Steel
Seals
Manual Override
Code
Omit Push Pin (Standard)
PB
SPS
-
-
OPS
PAT
PAP
Material
Code
Buna-N
B
Viton
V
Manual Override
Push Button
Screw Style (Push-Type Valve)
Push Pin Nut for Protection & Actuation
Push and Twist
Push and Pull
Body Nomenclature
No Body
SDC10-5-6S
SDC10-5-8S
SDC10-5-S8S
SDC10-5-L3B
SDC10-5-L4B
SDC10-5-S4B
Seal kit
11192395
11192396
SV - 228
Loading...