Data Sheet
Steel Valve with Air-Vent for Convectors in
Two-Pipe Heating Systems
Application
Code no. and technical
data
The steel valve is designed for welding into
convectors by the manufacturer. The complete valve consists of a steel valve body, an
air-vent and a valve insert with integrated
presetting of max. flow through the convector. The insert has connection for all
Danfoss RA 2000 thermostatic sensors.
The flow capacity of this valve is designed
for conventional two-pipe heating systems.
Part Code no.
Valve insert with RA 2000 sensor connection 013G0394
Steel valve body, straight pattern, welding connections 013G1803
Air-vent 640G0168
Cover cap, black 013G8439
Valve body, insert, airvent and cap 013G1810
Spare part: Gland seal for 013G0394, 10 pcs./pack 013L0669
Code no. Sensor connection Presetting
kv-value
1 2 3 4 5 6 7 N N
013G1810 RA2000 0.09 0.14 0.19 0.28 0.46 0.61 0.72 0.79 0.95
1)
vs
k
Code no. Max. water
temp.
°C bar bar bar bar
013G1810 120 0.05-0.2 0.6 25 16
1)
kv-values indicate the flow volume (Q) in m3/h at a pressure loss (∆p) across the valve of 1 bar.
kv = Q / √∆p. At setting N, the kv-value in accordance with EN 215 can be stated as Xp = 2 K. At lower
preset values, Xp will be reduced until approximately Xp 0.5 at presetting 1. The table shows the average measured values for integrated valves with radiator. The kvs-values indicate the valve capacity,
when the valve is fully open.
2)
The technical differential pressure indicates the upper limit for a proper valve function. In most twopipe systems the recommended differential pressure is sufficient. In order to achieve a noiseless function we recommend in smaller systems to apply automatic bypass valves or automatic balancing
valves. If pump differential pressure exceeds the recommended max. valve differential pressure it is recommended that an automatic balancing valve type ASV-P/PV is added to the system.
Danfoss Heating Solutions VDFOG102 © Danfoss 10/2012 1
Differential pressure
Rec. Tech.
2)
Test pres-
sure
Work. pres-
sure
Data Sheet Steel Valve with Air-Vent for Convectors in Two-Pipe Heating Systems
Presetting
Materials in contact with
water
The presetting values of the integrated valves
can be adjusted easily and accurately without the
use of tools (factory setting: ‘N’):
Remove the protective cap or the thermo-
▪
static sensor
Find the reference mark
▪
Turn the setting ring until the desired pre-
▪
setting number aligns with the reference
mark.
Presetting can be selected within the range of 1
to 7. At setting ‘N’ the valve is fully open. Setting
in the shaded areas of the drawing should be
avoided.
Valve body Steel
Valve top Ms 58
Valve seat Ms 58
Throttle nozzle PPS
Setting dial ABS Plastic
O-rings NBR/EPDM
Valve spindle PPS
Valve cone NBR
Pressure pin and valve spring Chrome steel
Air vent/plug Brass
Setting ‘N’ is used when flushing the system.
When the thermostatic sensor is fitted, the presetting is hidden and thus protected against unintended alteration.
To avoid calcification and corrosion, it is important for the composition of the circulating water
to comply with the VDI 2035 guidelines.
2 VDFOG102 © Danfoss 10/2012 Danfoss Heating Solutions
5 7 10 20 30 40 50 70 100 200 300 400 500 700 1000
1
2
3
4
5
6
8
kPa
20
30
40
50
60
80
100
1
0,8
0,6
0,5
0,4
0,3
0,2
0,1
0,08
0,06
0,05
0,04
0,03
0,02
0,01
10
p
p
Q [l/h]
[ ]
[
bar
]
0,1
0,2
0,3
0,4
0,5
0,6
0,8
1
2
3
4
5
6
8
10
p
1 2 3
4
5 6
7
N
107543210,70,50,40,30,20,1
200,2 0,3 0,4 0,5 0,7 1 2 3 4 5 7 10
kW
kW
t=15 C
o
o
t=20 C
]
mwg
[
2000
20 30
30 40
2
t=10 C
0,40,1
o
0,2 0,3 0,5 0,7 1 103 4 75 20
kW
0,07
013G1810 RA-N
Data Sheet Steel Valve with Air-Vent for Convectors in Two-Pipe Heating Systems
Capacities without Convectors
Capacities at Xp = 2K with Danfoss radiator thermostats are measured without convector and
connection fittings.
Danfoss Heating Solutions VDFOG102 © Danfoss 10/2012 3
Max.
70°C
Min. 120 mm
Data Sheet Steel Valve with Air-Vent for Convectors in Two-Pipe Heating Systems
Dimensions
Mounting Instructions
Built-in valve, type RA-N, code no. 013G0394
Lubricate valve insert by dipping in water. Insert the built-in valve into the steel valve
housing
4 VDFOG102 © Danfoss 10/2012 Danfoss Heating Solutions
x 12
30Nm
10Nm
1)
2)
10 Nm
Data Sheet Steel Valve with Air-Vent for Convectors in Two-Pipe Heating Systems
Fasten built-in valve, with a torque of 30 Nm +/- 10%.
21M Spanner.
Fasten air-vent, with a torque of 10 Nm +/10%. 13M spanner.
Fit protection cap. Tighten cap.
Replacement of gland seal
Replace the gland seal, code no. 013L0669. Can be done
without draining the heating system.
1)
17M spanner for fixing the setting dial,
2)
10M spanner
Test operation of valve spindle, by
pushing the pin.
Danfoss Heating Solutions VDFOG102 © Danfoss 10/2012 5
Data Sheet Steel Valve with Air-Vent for Convectors in Two-Pipe Heating Systems
6 VDFOG102 © Danfoss 10/2012 Danfoss Heating Solutions
Data Sheet Steel Valve with Air-Vent for Convectors in Two-Pipe Heating Systems
Danfoss Heating Solutions VDFOG102 © Danfoss 10/2012 7
Data Sheet Steel Valve with Air-Vent for Convectors in Two-Pipe Heating Systems
Danfoss A/S
Heating Solutions
Haarupvaenget 11
8600 Silkeborg
Denmark
Phone: +45 7488 8000
Fax: +45 7488 8100
Email: heating.solutions@danfoss.com
www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective
companies. Danfoss Heating Solutions and the Danfoss Heating Solutions logotype are trademarks of Danfoss A/S. All rights reserved.
8 VDFOG102 © Danfoss 10/2012 Danfoss Heating Solutions
Loading...