|
|
INSTRUCTIONS |
|
|||
|
|
RLV-D lockshield valve |
|
|||
|
|
with push-fit elbow |
|
|||
<![if ! IE]> <![endif]>013R9330 |
|
|
|
|
|
<![if ! IE]> <![endif]>013R9330 |
Plastic pipes |
Copper pipes |
|
|
|||
|
|
|
|
|||
|
According to BS 7291: |
According to BS 2871 |
|
|
|
|
|
Max. 92 °C, 3 bar. |
part 1 / BS EN 1057: |
|
|
|
|
|
|
Max. 92 °C, 3 bar. |
|
|
|
|
|
Cutting the pipes |
|
|
|
|
|
|
1. Cut the pipe square ensuring it is free of score |
|
||||
|
marks. For plastic pipes we recommend the |
|
|
|
||
|
use of a plastic pipe cutter. Do not use a |
|
|
|
||
|
hacksaw. |
|
|
|
|
|
|
2. To avoid damage to the pipe insert make sure |
|
|
|
||
|
burrs and sharp edges are removed. |
|
|
|
||
|
3. Insert the pipe insert into the plastic pipe. Do |
|
|
|
||
|
not use any lubricant. |
|
|
|
|
|
|
|
IMPORTANT: Always |
|
|
||
|
|
|
|
|
||
|
|
|
use inserts of same |
|
|
|
|
|
|
make/brand as the pipe. |
|
|
|
|
|
|
|
|
|
|
|
Mounting |
|
|
|
|
|
|
Ensure the pipe is pushed to the |
IMPORTANT: |
|
|||
|
Both nuts have to be tightened. |
|
||||
|
pipe stop. |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
It is good practice to check the fitting |
|
|
|
|
|
|
before use; pull the pipe back to check |
|
|
|
|
|
|
it is secure. |
|
|
|
|
|
|
|
|
|
|
Dismounting |
|
|
IMPORTANT: |
|
|
|
|
|
|
Ensure system is depressurised |
|
|
|
|
|
|
before removing fitting. |
|
|
|
|
|
|
Push in collet squarely against |
|
|
|
|
|
|
face of fitting. With the collet |
|
|
|
|
|
|
held in this position, the pipe can |
|
|
|
|
|
|
be removed. The fitting can then |
|
|
|
|
|
|
be re-used. |
|
|
|
|
|
|
|
|
|
DKCD
VI.35.C1.02 09-2001
Collet cover and collet clip
Collet covers or collet clips provide added security against unintended pipe disconnection.
Collet clip, |
Collet cover, |
code no. 013G4913 (10 pcs.) |
code no. 013G4912 (10 pcs.) |
|
|
Removal of |
|
protective cap |
|
|
|
Blocking |
|
6 mm |
|
Allen key |
|
|
|
Setting and |
|
regulation |
¼ - 4 |
|
|
6 mm |
|
Allen key |
|
Turn till stop. |
Turn back: ¼ - 4 rev. |
DKCD
VI.35.C1.02 09-2001