Proportional Valves Technical Information
Proportional Flow Divider
PFD10-OD
OPERATION
PDF10-OD: Proportional Flow Divider, 10 Size, Normally Open, Divider This is a proportional, compensated, normally open, flow dividing, pre-
engineered HIC. When there is no current applied to the coils, the inlet flow is divided equally between ports A and B. As an example, if inlet flow is 40 LPM, the flow out Ports A and B will divide equally 20 LPM. The performance curve below shows input flow examples of 40, 20 and 10 LPM. Minimum inlet flow is 10 LPM (2.6 GPM). The flow ratio between ports A and B will proportionally vary as current is provided to coils S1 or S2. As current increases to coil S2, the flow to Port B will proportionally increase, while Port A decreases, as shown in the graph. Inversely, as current increases to coil S1, the flow to Port A will proportionally increase, while Port B decreases.
Note that this is not a combiner, the flow only exits Ports A and B. Connect the drain port DR to tank, limiting the pressure on this port to 50 bar (720 psi).
APPLICATIONS
Proportionally divide the input flow between two motors or hydraulic circuits (like HICs). Circuits that can take advantage of this pre-engineered HIC include any function where the motors or the HICs continuously require flow, and you only need to proportionally manage the amount of flow between them. Achieve repeatable, load-
independent flow dividing with the built-in pressure compensator. See performance curve below for compensation capabilities.
Note: For optimal performance, install with the solenoid valve in the horizontal position, reducing the chance for
SPECIFICATIONS |
|
|
SCHEMATIC |
|
|
|
|
Rated Pressure |
230 bar [3335 psi] |
|
|
Maximum Rated Flow |
40 l/min |
|
|
|
[10.6 US gal/min] |
|
|
Maximum Pressure in |
50 bar |
|
|
Port DR |
[ 720 psi ] |
|
|
Minimum Inlet Flow |
10 l/min [2.6 US gal/min] |
|
|
Weight including Coil |
1.15 kg [2.53 lb] |
|
|
Coil |
M16 |
26 Watts |
|
Coil Voltage |
12 V |
24 V |
|
Max. Control Current |
1.5 Amp |
0.75 Amp |
|
|
|
|
|
Hysteresis |
< 4% |
|
|
|
|
|
|
THEORETICAL PERFORMANCE
BC332375973113en-000101 • February 2020 |
PV - 53 |
Proportional Valves Technical Information
Proportional Flow Divider
PFD10-OD
DIMENSIONS mm [in]
235.3 |
[9.26] |
20mm
4-6 Nm [35-53 lbf * in]
Coil Nut Kit P/N 1740031 |
|
S2 |
S1 |
109 |
8 |
|
|
[4.29] |
|
||
[0.31] |
|
||
n8.5 [0.335] |
82 |
||
|
|||
|
[3.23] |
||
THRU HOLES 2 PLACES |
|
||
|
|
<![endif]>98 [3.50] 105 [4.13] APPROX 123 [4.85]
EXAMPLE CIRCUITS
Proportionally dividing |
Proportionally dividing |
flow between two motors |
flow between two hydraulic |
|
systems (HICs) |
ORDERING INFORMATION
BC332375973113en-000101 • February 2020 |
PV - 54 |