Danfoss NLV12.6CN Data sheet
Datasheets
NLV12.6CN
Variable Speed Drive Compressor
R290, 220-240V 50/60Hz with 105N4710 Controller
General
Code number (without electronic unit) 105H6355
Electronic unit 105N4710
Approvals EN 60335-2-34, CCC
Compressors on pallet 80
Application
Application LBP/MBP
Frequency Hz 50 60
Evaporating temperature °C -40 to 10 -40 to 10
Voltage range V 198 - 254 198 - 254
Max. condensing temperature continuous (short) °C 60 (65) 60 (65)
Max. winding temperature continuous (short) °C 125 (135) 125 (149)
Cooling requirements
Frequency Hz 50 60
Application
32°C F2F2– F2F2–
38°C F2F2– F2F2–
43°C F2F2– F2F2–
Remarks on application:
Features
Speed range rpm 2000 - 4500
Thermostat
Protections current, speed, temperature
Protection class (electronic unit) IP54
Motor
Motor type permanent magnet
LRA (rated after 4 sec. UL984), A electronic cut off
Maximum current A 7.0
Resistance, all 3 windings (25°C) Ω 5.3
LBP MBP HBP LBP MBP HBP
integrated,
electronic
This product is approved for
R290 regarding explosion
safety according to standard
EN 60335-1 and EN 603352-34
S = Staticcoolingnormallysufcient
O = Oil cooling
F1 = Fan cooling 1.5 m/s
(compressor compartment temp.
equal to ambient temperature)
F2 = Fan cooling 3.0 m/s necessary
SG = Suction gas cooling normally
sufcent
– = not applicable in this area
Design
Displacement cm
Oil quantity (type) cm
Maximum refrigerant charge g 150
Free gas volume in compressor cm
Weight - Compressor/Electronic unit kg 11.6 / 1.2
Dimensions
Height mm A 203
Suction connector location/I.D. mm | angle C 8.2 | 45°
material | comment Copper | Rubber plug
Process connector location/I.D. mm | angle D 6.2 | 25°
material | comment Copper | Rubber plug
Discharge connector location/I.D. mm | angle E 6.2 | 15°
material | comment Copper | Rubber plug
Oil cooler connector location/I.D. mm | angle F –
material | comment –
Connector tolerance I.D. mm ±0.09
Accessories Code number
Cover 103N2008
Mounting accessories Code number
Bolt joint for one compressor Ø: 16 mm 118-1917
Bolt joint in quantities Ø: 16 mm 118-1918
Snap-on in quantities Ø: 16 mm 118-1919
3
3
3
320 (polyolester)
B 197
12.55
2360
© Danfoss | DCS (CC) | 2017.09
DEHC.ED.100.J2.02 | 1
LBP: ASHRAE 220V, 50/60Hz, fan cooling F
Speed (rpm) 2000 2250 2500 2750 3000 3500 4000 4500 Test conditions
Capacity [W] 422 481 541 597 653 748 843 938 Evaporation pressure -23.3˚C
Power cons. [W] 251 280 309 340 370.7 436 500 565 Condensing presssure 54.4˚C
Current cons. [A] 1.23 1.36 1.49 1.63 1.77 2.06 2.35 2.64 Liquid temperature 32.2˚C
COP [W/W] 1.68 1.72 1.75 1.76 1.76 1.72 1.69 1.66 Return gas temperature 32.2˚C
2
LBP: CECOMAF 220V, 50/60Hz, fan cooling F
Speed (rpm) 2000 2250 2500 2750 3000 3500 4000 4500 Test conditions
Capacity [W] 316 360 404 448 492 562 633 703 Evaporation pressure -25˚C
Power cons. [W] 243 269 296 326 357 419 482 545 Condensing presssure 55˚C
Current cons. [A] 1.19 1.31 1.43 1.57 1.70 1.99 2.27 2.55 Liquid temperature 55˚C
COP [W/W] 1.30 1.34 1.37 1.37 1.38 1.34 1.31 1.29 Return gas temperature 32˚C
LBP: EN12900 220V, 50/60Hz, fan cooling F
Speed (rpm) 2000 2250 2500 2750 3000 3500 4000 4500 Test conditions
Capacity [W] 257 281 306 333 360 430 500 570 Evaporation pressure -35˚C
Power cons. [W] 189 203 217 239 261 311 361 411 Condensing presssure 40˚C
Current cons. [A] 0.91 0.98 1.04 1.13 1.22 1.44 1.66 1.87 Liquid temperature 40˚C
COP [W/W] 1.36 1.38 1.41 1.39 1.38 1.38 1.38 1.39 Return gas temperature 20˚C
MBP: ASHRAE 220V, 50/60Hz, fan cooling F
Speed (rpm) 2000 2250 2500 2750 3000 3500 4000 4500 Test conditions
Capacity [W] 750 849 947 1040 1132 1310 1489 1667 Evaporation pressure -6.7˚C
Power cons. [W] 343 390 436 475 514 612 710 808 Condensing presssure 54.4˚C
Current cons. [A] 1.66 1.87 2.08 2.26 2.44 2.89 3.33 3.78 Liquid temperature 46.1˚C
COP [W/W] 2.18 2.18 2.18 2.19 2.20 2.14 2.10 2.06 Return gas temperature 35˚C
MBP: CECOMAF 220V, 50/60Hz, fan cooling F
Speed (rpm) 2000 2250 2500 2750 3000 3500 4000 4500 Test conditions
Capacity [W] 598 679 760 832 905 1046 1188 1329 Evaporation pressure -10˚C
Power cons. [W] 330 375 419 456 493 585 677 769 Condensing presssure 55˚C
Current cons. [A] 1.58 1.78 1.99 2.15 2.32 2.73 3.15 3.56 Liquid temperature 55˚C
COP [W/W] 1.81 1.81 1.81 1.83 1.83 1.79 1.75 1.73 Return gas temperature 32˚C
2
2
2
2
MBP: EN12900 220V, 50/60Hz, fan cooling F
Speed (rpm) 2000 2250 2500 2750 3000 3500 4000 4500 Test conditions
Capacity [W] 686 769 852 932 1011 1183 1354 1525 Evaporation pressure -10˚C
Power cons. [W] 320 359 398 434 471 559 647 735 Condensing presssure 45˚C
Current cons. [A] 1.47 1.64 1.80 1.96 2.12 2.49 2.87 3.25 Liquid temperature 45˚C
COP [W/W] 2.14 2.14 2.14 2.15 2.15 2.12 2.09 2.07 Return gas temperature 20˚C
Optimization Point 220V, 50/60Hz, fan cooling F
Speed (rpm) 2000 2250 2500 2750 3000 3500 4000 4500 Test conditions
Capacity [W] 428 481 535 583 630 737 844 951 Evaporation pressure -25˚C
Power cons. [W] 217 238 259 284 309 368 427 486 Condensing presssure 35˚C
Current cons. [A] 1.08 1.17 1.26 1.38 1.49 1.76 2.02 2.29 Liquid temperature 35˚C
COP [W/W] 1.972 2.025 2.069 2.052 2.038 2.002 1.976 1.956 Return gas temperature 32˚C
Optimization Point 220V, 50/60Hz, fan cooling F
Speed (rpm) 2000 2250 2500 2750 3000 3500 4000 4500 Test conditions
Capacity [W] 701 786 870 952 1033 1208 1383 1558 Evaporation pressure -10˚C
Power cons. [W] 305 342 379 413 448 532 616 700 Condensing presssure 45˚C
Current cons. [A] 1.47 1.64 1.80 1.96 2.12 2.49 2.87 3.25 Liquid temperature 45˚C
COP [W/W] 2.30 2.30 2.30 2.30 2.31 2.27 2.25 2.23 Return gas temperature 32˚C
Optimization Point 220V, 50/60Hz, fan cooling F
Speed (rpm) 2000 2250 2500 2750 3000 3500 4000 4500 Test conditions
Capacity [W] 1197 1330 1462 1618 1774 2070 2366 2662 Evaporation pressure 5˚C
Power cons. [W] 372 410 447 502 556 664 772 879 Condensing presssure 45˚C
Current cons. [A] 1.77 1.94 2.11 2.36 2.60 3.09 3.57 4.06 Liquid temperature 45˚C
COP [W/W] 3.22 3.25 3.27 3.22 3.19 3.12 3.07 3.03 Return gas temperature 32˚C
2
2
2
2
© Danfoss | DCS (CC) | 2017.09
DEHC.ED.100.J2.02 | 2
Loading...