Datasheets
NLE11MF.2
Energy-optimized MBP Compressor
R134a, 220-240V 50Hz
General
Code number 105G6197
Approvals
Compressors on pallet 80
Application
Application LBP/MBP
Frequency Hz 50 60
Evaporating temperature °C -25 to 10 –
Voltage range V 198 to 242/254 –
Max. condensing temperature continuous (short) °C 60 (70) –
Max. winding temperature continuous (short) °C 125 (135) –
Cooling requirements
Frequency Hz 50 60
Application
32°C F2F2– – – –
38°C F2F2– – – –
43°C F2F2– – – –
Remarks on application:
Voltage range: without run capacitor: 198 to 242V / with run capacitor: 198 to 254V
Motor
Motor type CSIR/RSIR/RSCR
LRA (rated after 4 sec. UL984), HST | LST A 13.1 11.4
Cut in Current, HST | LST A 13.1 15.7
Resistance, main | start winding (25°C) Ω 8.8 19.0
EN 60335-2-34 w. Annex AA, CCC
LBP MBP HBP LBP MBP HBP
S =Staticcoolingnormallysufcient
O = Oil cooling
F1 = Fan cooling 1.5 m/s
(compressor compartment temperature
equal to ambient temperature)
F2 = Fan cooling 3.0 m/s necessary
SG =Suctiongascoolingnormallysufcent
– = not applicable in this area
Design
Displacement cm
Oil quantity (type) cm
Maximum refrigerant charge g 600
Free gas volume in compressor cm
Weight without electrical equipment kg 10.9
Dimensions
Height mm A 203
Suction connector location/I.D. mm | angle C 8.2 | 45°
material | comment Copper | Rubber plug
Process connector location/I.D. mm | angle D 6.2 | 25°
material | comment Copper | Rubber plug
Discharge connector location/I.D. mm | angle E 6.2 | 15°
material | comment Copper | Rubber plug
Oil cooler connector location/I.D. mm | angle F –
material | comment –
Connector tolerance I.D. mm ±0.09
Remarks:
3
3
3
320 (polyolester)
B 197
B1 –
B2 –
11.15
2360
© Danfoss | DCS (CC) | 2017.04
DEHC.ED.200.F5.02 | 1
EN 12900 LBP 220V, 50Hz, fan cooling F
Evap. temp. in °C -45 -40 -35 -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 5 7.2 10 15 20
Capacity in W 311 340 404 516 649 749 805 985 1192 1292 1428
Power cons. in W 224 234 254 286 320 342 354 387 418 431 447
Current cons. in A 1.72 1.76 1.83 1.92 2.00 2.04 2.07 2.15 2.24 2.28 2.35
COP in W/W 1.38 1.45 1.59 1.80 2.03 2.19 2.27 2.55 2.85 3.00 3.20
2
EN 12900 MBP 220V, 50Hz, fan cooling F
Evap. temp. in °C -45 -40 -35 -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 5 7.2 10 15 20
Capacity in W 290 318 378 484 611 706 759 931 1129 1226 1356
Power cons. in W 231 241 261 295 331 355 368 405 441 457 476
Current cons. in A 1.78 1.82 1.89 1.97 2.05 2.11 2.14 2.23 2.35 2.41 2.49
COP in W/W 1.26 1.32 1.45 1.64 1.85 1.99 2.06 2.30 2.56 2.68 2.85
ASHRAE LBP 220V, 50Hz, fan cooling F
Evap. temp. in °C -45 -40 -35 -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 5 7.2 10 15 20
Capacity in W 300 331 396 513 654 761 821 1018 1246 1357 1508
Power cons. in W 224 235 257 293 334 362 377 421 466 485 510
Current cons. in A 1.79 1.82 1.89 2.00 2.11 2.19 2.24 2.38 2.56 2.65 2.78
COP in W/W 1.34 1.41 1.54 1.75 1.96 2.10 2.18 2.42 2.68 2.80 2.96
ASHRAE MBP 220V, 50Hz, fan cooling F
Evap. temp. in °C -45 -40 -35 -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 5 7.2 10 15 20
Capacity in W 268 295 353 457 582 678 731 905 1107 1205 1339
Power cons. in W 222 232 254 290 330 358 373 416 460 479 503
Current cons. in A 1.79 1.82 1.89 2.00 2.11 2.19 2.24 2.38 2.56 2.65 2.78
COP in W/W 1.21 1.27 1.39 1.57 1.76 1.89 1.96 2.17 2.41 2.51 2.66
2
2
2
Accessories for NLE11MF.2 Figure Code number Test conditions
ePTC starting device 6.3 mm spade connectors
4.8 mm spade connectors 103N0050 Ambient temperature 32°C 32°C 32.2°C 35°C
Starting relay 6.3 mm spade connectors a2 117U6003 Suction gas temperature 20°C 20°C 32.2°C 35°C
Start. capacitor 80 µF 6.3 mm spade connectors c 117U5015 Liquid temperature no subcooling 32.2°C 46.1°C
Cover b 103N2010
Cord relief d 103N1010 Mounting accessories Code number
Protection screen for PTC g – Bolt joint for one comp. Ø: 16 mm 118-1917
a1
– Condensing temperature 40°C 45°C 54.4°C 54.4°C
Bolt joint in quantities Ø: 16 mm 118-1918
Snap-on in quantities Ø: 16 mm 118-1919
© Danfoss | DCS (CC) | 2017.04
EN 12900
LBP MBP
DEHC.ED.200.F5.02 | 2
ASHRAE
LBP MBP
Loading...