Datasheets
NLE11CNL Energy-optimized LBP Compressor
R290, 115-127V 60Hz
General
Code number |
|
|
|
|
105H5981 |
|
|
|
||
Approvals |
|
|
|
|
UL984 |
|
|
|
||
Compressors on pallet |
|
|
|
|
80 |
|
|
|
||
Application |
|
|
|
|
|
|
|
|
|
|
Application |
|
|
|
|
LBP |
|
|
|
||
Frequency |
|
Hz |
|
50 |
|
|
|
60 |
|
|
Evaporating temperature |
|
°F |
|
– |
|
|
-31 to 14 |
|||
Voltage range |
|
V |
|
– |
|
|
95 - 135 |
|||
Max. condensing temperature continuous (short) |
°F |
|
– |
|
|
149 (149) |
||||
Max. winding temperature continuous (short) |
°F |
|
– |
|
|
257 (275) |
||||
Cooling requirements |
|
|
|
|
|
|
|
|
|
|
Frequency |
|
Hz |
|
50 |
|
|
|
60 |
|
|
Application |
|
|
LBP |
MBP |
HBP |
|
LBP |
MBP |
|
HBP |
90°F |
|
|
– |
– |
– |
|
F2 |
– |
|
– |
100°F |
|
|
– |
– |
– |
|
F2 |
– |
|
– |
110°F |
|
|
– |
– |
– |
|
F2 |
– |
|
– |
Remarks on application: |
|
|
|
|
|
|
|
|
|
|
Motor |
|
|
|
|
|
|
|
|
|
|
Motor type |
|
|
|
CSIR/RSCR |
|
|||||
LRA (rated after 4 sec. UL984), HST | LST |
A |
|
28.7 |
|
|
|
29.9 |
|
|
|
Cut in Current, HST | LST |
|
A |
|
28.7 |
|
|
|
39.2 |
|
|
Resistance, main | start winding (77°F) |
Ω |
|
1.10 |
|
|
|
3.61 |
|
|
|
Design |
|
|
|
|
|
|
|
|
|
|
Displacement |
|
cu.in |
|
|
0.68 |
|
|
|
||
Oil quantity (type) |
|
fl.oz. |
|
10.2 (polyolester) |
|
|||||
Maximum refrigerant charge |
|
oz. |
|
|
5.3 |
|
|
|
||
Free gas volume in compressor |
|
fl.oz. |
|
|
79.8 |
|
|
|
||
Weight without electrical equipment |
lbs. |
|
|
26.7 |
|
|
|
|||
Dimensions |
|
|
|
|
|
|
|
|
|
|
Height |
|
inch |
A |
|
7.99 |
|
|
|
||
|
|
|
B |
|
7.76 |
|
|
|
||
|
|
|
B1 |
|
|
– |
|
|
|
|
|
|
|
B2 |
|
|
– |
|
|
|
|
Suction connector |
location, I.D. in. | angle |
C |
0.320-0.327 | 45° |
|
|
|||||
|
material | comment |
|
Copper | Rubber plug |
|
||||||
Process connector |
location, I.D. in. | angle |
D |
0.252-0.259 | 25° |
|
|
|||||
|
material | comment |
|
Copper | Rubber plug |
|
||||||
Discharge connector |
location, I.D. in. | angle |
E |
0.252-0.259 | 15° |
|
|
|||||
|
material | comment |
|
Copper | Rubber plug |
|
||||||
Oil cooler connector |
location, I.D. in. | angle |
F |
|
|
– |
|
|
|
||
|
material | comment |
|
|
|
– |
|
|
|
||
Remarks: |
|
|
|
|
|
|
|
|
|
|
This product is approved for R290 regarding explosion
safety according to standard EN 60335-1 and EN
60335-2-34
S |
= Static cooling normally sufficient |
O |
= Oil cooling |
F1 |
= Fan cooling 1.5 m/s |
|
(compressor compartment temperature |
|
equal to ambient temperature) |
F2 |
= Fan cooling 3.0 m/s necessary |
SG |
= Suction gas cooling normally sufficent |
–= not applicable in this area
© Danfoss | DCS (CC) | 2017.08 |
DEHC.ED.100.G1.22 | 1 |
Loading...