Danfoss FCM 300 Fact sheet

VLT® DriveMotor FCM 300

The VLT® DriveMotor FCM 300 series is an integrated drive-motor solution which combines
a VLT® frequency converter and a high standard quality motor in a single product.

IE2

motors for high
efficiency combined
with a high­performance, energy
saving VLT ®.

The frequency converter is attached
in place of the motor terminal box
and it is no higher than the standard
terminal box nor wider or longer than
the motor.

Incorporated to a high standard
quality motor, the VLT® DriveMotor
FCM 300 is also available in a multi­tude of variants, individualised to
meet customer requirements.

On the motor
The VLT® electronic motor control
together with the motor totally
eliminates motor cables and thereby
minimises EMC problems. Heat from
the drive is dissipated together with
the motor heat.

Feature Benet

Reliable Maximum uptime

Robust enclosure Withstands harsh environments
No power cable length limitation Increased exibility
Thermal protection Total motor-inverter protection

Straightforward EMC compliance

User-friendly Saves commissioning and operating cost

Motor and drive perfectly matched
to each other

No panel space required – the DriveMotor is
placed on the machine

Flexible mounting – foot/ange/face/
foot-ange/foot-face

Retrot without mechanical changes Easy service

Set-up and controlled through a remote control
panel or eldbus communication and dedicated
MCT 10 set-up software

Power range

0.55 – 7.5 kW, 3 x 380 – 480 V

Enclosure

IP 55 (standard)
IP 65/IP 66 (optional)

Motor type

2-pole
4-pole

Mounting versions
B03 foot
B05 ange
B35 foot + ange
B14 face
B34 foot + face

No problem with electromagnetic
interferences

Saves commissioning time

Saves space

Meets customer requirements

Easy commissioning

Facts about our products

Control panel

A Local Control Panel is used for
operating, setup and diagnostics. The
LCP can be handheld or mounted in a
panel front (IP 65).

Sleep Mode

In Sleep Mode the motor will stop in a
no load situation. When the load
returns, the frequency converter will
restart the motor.

Specications

Mains supply (L1, L2, L3)

Supply voltage 3 x 380/400/415/440/460/480V ± 10%
Supply frequency 50/60 Hz
Power factor (cos φ) Max. 0.9/1.0 at rated load
Max. imbalance of supply voltage ±2% of rated supply voltage
Switching on supply input Once every 2 minutes

Control Characteristics (frequency converter)

Frequency range 0 – 132 Hz
Overload torque 160% for 60 sec.
Resolution on output frequency 0.1%
System response time 30 msec. ± 10 msec.

Speed accuracy

Digital inputs

Programmable digital inputs 4
Voltage level 0 – 24 V DC (PNP positive logic)

Analogue inputs

Analogue inputs 2 (1 voltage, 1 current)
Voltage/current level 0 – 10 V DC / 0/4 – 20 mA (scaleable)

Pulse input

Programmable pulse inputs 1 (24 V DC)
Max. frequency 70 kHz (push-pull) / 8 kHz (open collector)

Analogue/digital output

Programmable analogue/digital outputs 1
Current/voltage range 0/4 – 20 mA / 24 V DC

Relay output

Programmable relay outputs 1
Max. terminal load 250 V AC, 2 A, 500 VA

Fieldbus communication

FC Protocol, Modbus RTU Built-in
Probus DP Optional (integrated)

Externals

Vibration test 1.0 g (IEC 60068)
Max. relative humidity 95% (IEC 60068-2-3)
Ambient temperature Max. 40˚C (24 hour average max. 35˚C)
Min. ambient temperature in full operation 0˚C
Min. ambient temperature at reduced

performance

±15 RPM (open loop, CT mode,
4-pole motor 150 – 1500 RPM)

-10˚C

Also available:

Forced ventilation

For constant operation at low speed
without torque reduction.

Motor drain holes

For applications where formation of
condensate water might occur.

Sensorless Pump Control
– OEM version

Oers precise pressure (head) control
without using a pressure transmitter.

Danfoss VLT Drives, Ulsnaes 1, DK-6300 Graasten, Denmark, Tel. [phone], Fax [phone]
www.danfoss.com/drives • E-mail: [e-mail]

DKDD.PFP.701.A2.02 VLT® is a trademark of Danfoss A/S Produced by PE-MMSC 2014.09

Technical Data

FCM 305 307 311 315 322 330 340 355 375

Motor output
[HP]
[kW]

Motor torque
2-pole [Nm]
4-pole [Nm]

Frame size [mm] 80 80 90 90 100 100 112 132 132
Input current [A] 380 V

2-pole
4-pole

Input current [A] 480 V
2-pole
4-pole

1)

at 400 V, 3000 RPM

2)

at 400 V, 1500 RPM

1)

2)

0.75

0.55

1.8

3.5

1.5

1.4

1.2

1.1

1.0

0.75

2.4

4.8

1.8

1.7

1.4

1.3

1.5

1.1

3.5

7.0

2.3

2.5

1.8

2.0

2.0

1.5

4.8

9.6

3.4

3.3

2.7

2.6

3.0

2.2

7.0

14.0

4.5

4.7

3.6

3.7

4.0

3.0

9.5

19.1

5.0

6.4

4.0

5.1

5.0

4.0

12.6

25.4

8.0

8.0

6.3

6.3

7.5

10.0

5.5

7.5

17.5

24.0

35.0

48.0

12.0

15.0

11.0

15.5

9.5

11.9

8.7

12.3