Danfoss EvaKool SupaKool Instruction Manual
Instruction Manual
1 |
P a g e
Nexberg Pty Ltd T/a Evakool
16 Enterprise St CALOUNDRA
QLD 4551
Tel : 07 5492 7777
Fax : 07 5492 7733
Please read this manual and the Safety Instructions carefully before using
your refrigerator.
1. Safety Instructions Page 2
2. Notes on using the product Page 2
3. Operation Page 2-4
4. WiFi Operation Page 5-12
5. Cleaning and Maintenance Page 13
6. Troubleshooting Page 13
7. Error Codes Page 14
8. Warranty Statement Page 15
Instruction Manual
2 |
P a g e
Features:
• Reliable cooling system with Danfoss designed compressor manufactured by SECOP
• Efficient electronic technology, low energy consumption
• Multi-voltage system (DC 12-24 Volt) and (AC 100-120/220-240 Volt)
• Digital Battery Protection - protects your vehicle battery effectively
1. Safety Instructions
• Warning: Do not touch exposed cables.
• Warning: Do not use fridge if you suspect any connections could be wet.
• When using the fridge please ensure the circuit being used is fused.
• Any installation of DC power sources should be handled by a qualified professional.
• Make sure the source voltage is correct. The technical data label shows the voltage data.
• Do not place any electrical devices inside the refrigerator as moisture could harm these
devices.
2. Notes on using the product
Your refrigerator requires good ventilation, especially around the vents of the refrigerator;
allow a gap of at least 200mm around the vents and 100mm around the rest of the unit.
Avoid humidity: Humidity inside the appliance can form frost and impair cooling. Do not
allow frost to build up.
Never wash the appliance using a hose or running water and never submerge the unit, as
water will damage the electronics.
Avoid placing your refrigerator near a heat source. A cooler environment helps the refrigerator
to work more efficiently and keep the contents cool.
Place the refrigerator on a flat surface and away from any edges. When using the fridge in a
vehicle, please use a fastening device to secure it.
3. Operation
Power
：：：：
The refrigerator can be powered by a multi-voltage system utilizing either 12/24
Volts or 240 Volts. The electronic module controls the compressor motor and has the added
function of a three stage battery protection. When the input voltage drops below the minimum,
the compressor will cut out; when the voltage comes back up to the cut-in value, the
compressor will restart automatically.
Battery Protection: The Danfoss compressor requires over 10.8 Volts (12 Volt System) or
23.0 Volts (24V System) to operate. If the voltage drops below this the fridge will stop
operating.
Instruction Manual
3 |
P a g e
Cable Specification
The DC cables must have a suitable cross-section for their length, according to this table:
*Note: The length is from the battery to the refrigerator.
Display Panel
Using the Fridge
• TO TURN ON: Plug in the DC or AC power cable. The LED display on the control panel
will light up and the interior temperature will be displayed.
• NOTE: IF THE UNIT IS OFF, ONLY AN ORANGE LED WILL BE ILLUMINATED. TO
TURN ON YOUR UNIT PLEASE HOLD THE ON/OFF SWITCH DOWN UNTIL THE
POWER LED CHANGES TO GREEN AND THE LED DISPLAY IS ILLUMINATED.
Cable Area 12V Max Cable
Length*
24V Max Cable
Length*
[mm2] AWG [m] [ft.] [m] [ft.]
2.5 12 2.5 8 5 16
4 12 4 13 8 26
6 10 6 20 12 39
10 8 10 33 20 66
Instruction Manual
4 |
P a g e
• SETTING THE TEMPERATURE:
• Press SET once and then the display will flash then press the + and - buttons to adjust the
temperature. Press the button + to increase and the button - to decrease the temperature. To
lock in the target temperature press SET three times. The display board will display the
current temperature inside the unit after the target temperature is set. After approximately 5
minutes the displayed temperature will start to decrease.
• Temperature setting range：-20ºC～+10ºC, -4ºF～+50ºF；
• If the power supply is cut off, the refrigerator will switch off automatically and then
automatically switch on again when the unit receives power.
• To change the fridge between ºC and ºF. Press SET twice and then + or - to change the
setting. Press SET twice to lock this in.
• CHANGING BATTERY VOLTAGE PROTECTION: To change the battery voltage
setting press the SET button three times and then use the + or - to change the setting.
Press SET once to lock this in. The three voltage settings are as follows :-
(Evakool recommends you keep the setting on LO)
o LO – 10.8 Volts
o NE – 11.4 Volts
o HI – 12.2 Volts
NOTE – Accuracy may be +/- 0.3V depending on installation
USB Charging Port and Thermostat Override Switch
USB Port – This USB port can be used to charge small devices. E.g. mobile phones. The socket is
rated to 500mA / 5 Volts.
Thermostat Override switch – If your digital thermostat fails and you are unable to set the
temperature, turn this switch to Emergency override. This enables the fridge to run until you reach a
service centre to replace the faulty component.
o If emergency override is enabled the compressor will attempt to run 100% of the time. As this
removes the ability to set the internal temperature and will increase power usage, it is not
recommended for everyday use.
Instruction Manual
5 |
P a g e
4. WiFi OPERATION
The fridge has been designed with the latest technology. You are able to easily download the
EVAKOOL APP from the Google Play store or the Apple iTunes Store.
Once the APP is installed please follow these easy instructions to be able to control and monitor your
fridge.
SCREENSHOT SHOWING WIRELESS NETWORK CREATED BY THE FRIDGE
To use your Smartphone with your fridge you must first be on the same Wireless Network as the
fridge. The fridge creates its own wireless network which you must connect to in the settings of your
phone.
Please take note of the Fridge ID number as it will be required for the APP. To connect to the wireless
network you will need a pass code which is “55555555” (8x 5’s). If you have any issues connecting
to the WiFi network please review the troubleshooting area at the end of this section.
Loading...