Danfoss EKF 1A, EKF 2A Data sheet

Data Sheet
Stepper Valve driver Type EKF 1A, EKF 2A
Driver for stepper motor valves
Stepper Valve Driver EKF series is for use where stepper valves must be accurately controlled typically in commercial air conditioning, heat pumps, commercial refrigeration and food retail applications
Features:
• Support both Bipolar and Unipolar stepper motor valves
• Fast installation and setup
• Lost step prevention
• Open circuit detection
• LED indication for valve movement and alarm/warnings
• On board DIP switch for quick selection
• Plug and play
• 4 pole terminal block and JST-XHP 5 pin connections
• Phoenix connector terminals
• Digital output for alarm signal
• 1 and 2 valve driver version available
AI383967949152en-000102
Features
EKF 1A
EKF 2A
Code number
080G5030
080G5035
Power supply
24 V AC/DC
24 V AC/DC
Number of valves
1 stepper motor valve
2 stepper motor valves
Valve type
Unipolar/Bipolar
Unipolar/Bipolar
Analog inputs
1
2
Digital outputs
1
1
Dip switch
1
2
Battery backup support
Yes
Yes
Mounting
35 mm, 4 DIN
35 mm, 4 DIN
Dimension (H x W)(mm)
110 x 70
110 x 70
EKE 2U Backup power module
Power supply
EKE 2U Backup power module ensures sucient power in case of power failures to the controller / driver to ensure closure of the electronic valves.
AK-PS
Input: 100 - 240 V AC/45 - 65 Hz Output: 24 V DC: available with 18 VA, 36 VA and 60 VA
ACCTRD
Input: 230 V AC, 50 - 60 Hz Output: 24 V AC, available with 12 VA, 22 VA and 35 VA
Stepper Valve driver, type EKF 1A, EKF 2A
Portfolio overview
Table 1: Portfolio overview
Table 2: Related Products
© Danfoss | Climate Solutions | 2022.03 AI383967949152en-000102 | 2
AI1
AI2
Unit programmable controller
ETS Colibri
AI1
Digital out
ETS Colibri
AI1
AI2
ETS Colibri
Digital out
Unit programmable controller
Analog input signal 1
Analog input signal 2
Stepper Valve driver, type EKF 1A, EKF 2A
Applications
EKF series stepper valve drivers can be used in application where accurate control of stepper motor valves are needed using analog input signals (0-10V, 0-5V, 4-20 mA, 0-20 mA) from unit programmable controllers. The product can be used for both Bipolar and Unipolar type valves. General applications include use in commercial air conditioning, heat pumps, commercial refrigeration and food retail application
Figure 1: EKF 1A
Figure 2: EKF 2A
© Danfoss | Climate Solutions | 2022.03 AI383967949152en-000102 | 3
Supply voltage
EKF 1A: 24 V AC / DC 50 / 60 Hz EKF 2A: 24 V AC / DC, 50 / 60 Hz
Power consumption
Idle operating: < 1 W (without valve) Data below shows power consumption for using 1 valve. When using two valves sum the power consumption of each valve.
CCMT 16 – CCMT 42 ETS 5M, ETS 6 ETS 12C – ETS 100C, KVS C ETS 12.5 – 400 ETS 500P, 800P CCMT 2- CCMT 8 CTR 20 CCMT L
25 VA / 15 W 20 VA / 10 W 30 VA /15 W 10 VA / 5 W 28 VA / 20 W 10 VA / 5 W 14 VA / 10 W 20 VA / 10 W
Analog inputs
EKF 1A: 1 input AI1
0-5 V, 0-10 V, 4-20 mA, 0-20 mA
EKF 2A: 2 inputs AI1 and AI2
0-5 V, 0-10 V, 4-20 mA, 0-20 mA
Max. 15 V Analog input voltage. Do not connect voltage sources to unpowered units without limiting the current to analog in­puts (overall 40 mA per input). Input Impedance: >50 kΩ (Voltage Input) 120 Ω ± 2% (Current Input)
Digital outputs
1 output for EKF1A / EKF 2A: D01 (open collector), sink current max 10 mA
Valve support
EKF 1A: 1 stepper motor valve output, EKF 2A: 2 stepper motor valve output STEPPER 1: A1, A2, B1, B2 STEPPER 2: A1, A2, B1, B2 Bipolar and unipolar stepper motor output:
- Danfoss ETS / KVS / ETS C / KVS C / CCMT 2 – CCMT 42 / CTR / CCMT L Valves
- ETS 6 / ETS 5M Valves Open circuit HW diagnostics is present.
Battery backup
1 input for EKF 1A / EKF2A: Vbat BAT, GND: Nominal 18 – 24 V DC, Min 16 V DC - Max 28 V DC (EKE 2U recommended) Max. battery current: 2 A at 18 V (valve depended) Battery alarm/warning will be activated below 16 V DC.
Enviroment
Storage
-30 – 80 °C / -22 – 176 °F
Operating
-20 – 60 °C / -4 – 140 °F
Humidity
< 90% RH, non-condensing
DIN Mounting
4 DIN, 35mm
Stepper valve driver
Product description
EKF 2A
Product type designation
080G5035
Product code number
24V AC/DC 50/60 Hz
Input power rating
PV01
Product version
SW1v00
Software version
QR code
Danfoss product information website
Made in Denmark
Country of origin
Danfoss A/S, 6430 Nordborg, Denmark
Company address
Stepper Valve driver, type EKF 1A, EKF 2A
Product specication
Table 3: Technical data
Identication
Product label is positioned behind the product.
Figure 3: Product label
Above product label is an example.
Table 4: Description
© Danfoss | Climate Solutions | 2022.03 AI383967949152en-000102 | 4
Koolprog PC Tool
Koolkey
DIP Switch1
Koolkey
Koolprog PC Tool
Stepper Valve driver, type EKF 1A, EKF 2A
Connection diagrams
Figure 4: EKF 1A
Figure 5: EKF 2A
NOTE:
There is both 4 pin terminal and JST 5 pin terminal available on the board per stepper drive output.
Only one of the terminals should be used per valve.
Do not connect valves to both 4 pin terminal and JST terminal of the same stepper driver output.
© Danfoss | Climate Solutions | 2022.03 AI383967949152en-000102 | 5
Description
Code No.
Stepper Valve Driver EKF 1A
080G5030
Stepper Valve Driver EKF 2A
080G5035
Stepper Valve driver, type EKF 1A, EKF 2A
Ordering
Table 5: Product part numbers
© Danfoss | Climate Solutions | 2022.03 AI383967949152en-000102 | 6
Stepper Valve driver, type EKF 1A, EKF 2A
Certicates, declarations, and approvals
The list contains all certicates, declarations, and approvals for this product type. Individual code number may have some or all of these approvals, and certain local approvals may not appear on the list.
Some approvals may change over time. You can check the most current status at danfoss.com or contact your local Danfoss representative if you have any questions.
Table 6: Approvals
© Danfoss | Climate Solutions | 2022.03 AI383967949152en-000102 | 7
Online support
Danfoss oers a wide range of support along with our products, including digital product information, software, mobile apps, and expert guidance. See the possibilities below.
The Danfoss Product Store
The Danfoss Product Store is your one-stop shop for everything product related—no matter where you are in the world or what area of the cooling industry you work in. Get quick access to essential information like product specs, code numbers, technical documentation, certications, accessories, and more. Start browsing at store.danfoss.com.
Find technical documentation
Find the technical documentation you need to get your project up and running. Get direct access to our ocial collection of data sheets, certicates and declarations, manuals and guides, 3D models and drawings, case stories, brochures, and much more.
Start searching now at www.danfoss.com/en/service-and-support/documentation.
Danfoss Learning
Danfoss Learning is a free online learning platform. It features courses and materials specically designed to help engineers, installers, service technicians, and wholesalers better understand the products, applications, industry topics, and trends that will help you do your job better.
Create your Danfoss Learning account for free at www.danfoss.com/en/service-and-support/learning.
Get local information and support
Local Danfoss websites are the main sources for help and information about our company and products. Find product availability, get the latest regional news, or connect with a nearby expert—all in your own language.
Find your local Danfoss website here: www.danfoss.com/en/choose-region.
© Danfoss | Climate Solutions | 2022.03 AI383967949152en-000102 | 8
Loading...