Danfoss ECpipeheat 10 V3 Data sheet

Data Sheet

YEAR

WARRANTY

Product specifications

Product

ECpipeheat 10 V3

The ECpipeheat 10 V3 is a self-limiting heating cable that is used for frost protection of pipes.
The self-limiting capability of the cable ensures that the output of the cable increase or

decrease according to ambient temperature.
A new self-limiting cable can be installed inside and outside water pipes. It is suitable for

drinking and common water pipes and is designed to be installed on pipe in all countries
and inside pipe in certified countries (DK, FI, SE, NO, RU). The product range cable on drum,
cut-to-length, ready-made cable with cold lead.

The product range: drum cable and cable with cold lead mains plug. All self-limiting
heating cables must be over-temperature protected by a thermostat, as the output
will decrease, but never be zero , and be protected by a RCD with a maximum trip
current of 30 mA.

Note 1: It is the full responsibility of the installer/designer to use proper cold lead dimensioned for
the purpose and assembly sets that establish sufficient mechanical strength, flammability resist­ance and water tightness - and to design the heating unit with correct output for the specific
application to avoid overheating of the cable or building materials.

Benefits

• Cut to length on site

• Ready-made lengths

• Small cable dimentions

• Inside and outside pipe installation

• Installation inside drinking water pipes

Approvals:

Standard compliance

• EN/IEC 60335-1:2012

• IEC 60800:2009

Nominal voltage 230 V~
Nominal output (tolerance) 10 W/m @ 10 °C (7,5-13,5 W/m @ 10 °C )
Max. permissible use temperature, powered 65 °C

Max. permissible use temperature, unpowered 65 °C

Minimum installation temperature - 5 °C

Max. water temperature (inside water pipe
installation)

Max. water pressure (inside water pipe
installation)

Heating cable dimensions 8,75 mm × 5,15 mm
Outer sheath HDPE + blue PVDF
Minimum Screen Coverage 100% aluminium foil
Maximum resistance protective braid 36 Ω/Km
Bending Ø, min. 50 mm (inside of the cable)
Cold lead with plug 2 m, 3 х 0,75 mm²
IP Class for ready made unit

IP Class for heating part and end termination

23 °C

10 bar

IP67
IP68

Types: Ready-made with Schuko plug

Ite m no. Cable length

088L1310 2 m 20 W 2 m 5703466250112
08 8 L1311 4 m 40 W 2 m 5703466250129

088 L1312 6 m 60 W 2 m 5703466250136
088 L1313 8 m 80 W 2 m 5703466250143
088L1314 10 m 100 W 2 m 5703466250150
088L1315 12 m 120 W 2 m 5703466250167
088L1316 14 m 140 W 2 m 5703466250174
088L1317 16 m 160 W 2 m 5703466250181
088L1318 19 m 190 W 2 m 5703466250198
088L1319 22 m 220 W 2 m 5703466250204
088L1320 25 m 250 W 2 m 5703466250211

Nominal output

@ 10 °C

Cold lead EAN no.

Electrical heating · ©Danfoss AI392949700379en-010102

Types: Drum

Ite m no.

Cable

length

088L13 0 0 300 m 300 m 1 10 W/m 5703466250044
088L13 01 900 m 900-1100 m 2, between 100 & 1100 m 10 W/m 5703466250051

Maximum heating circuit length on a pipe, with circuit breaker with C-characteristic

Switch on

temperature

10 °C 100 60

0 °C 96 -

-20 °C 77 -

ECpipeheat 10 V3

10 A

on pipe in pipe

Power output characteristic

Output of heating cable installed and measured on a pipe.

W/m

40

Min-max length

per drum

Number of length
allowed per drum

Nominal

output @ 10 °C

EAN no.

35

30

25

20

15

10

5

0

0 10 20 30 40 50 60

ECpipeheat 10 V3

Pipe temperature (°C)

AI392949700379en-010102Electrical heating · ©Danfoss