Danfoss CSV 2, CSV 22 Installation guide

32F866_02

32B04-CN-CSV

V

ss

32F868

ss

32F867

32F895_01

Installation guide

Solenoid valve

Types CSV 2 - CSV 22 (NC)

Refrigerants / 制冷剂:

R22, R134a, R404A, R507, R407C, R513A, R452A, R600,
R600a, R1234ze and R290.

032R9010

For other refrigerants, contact Danfoss.

有关与其它制冷剂的适用性问题，请联 系丹佛斯销售。

Note: Please follow specific selection criteria

Max. working pressure /

最大工作压力:

PS / MWP: 35 bar /508 psig

Max. operation pressure
differential (MOPD):

Coil dependent

最大开阀压差：
依 据 所 选 线 圈 型 号 ，参 考 样
本参数

Medium temperature / 介质温度:

-40 – 105 °C / -40 – 221 °F

Ambient temperature / 环境温度:

-20 – 55 °C / -4 – 131 °F

stated in the data-sheet for these particular
refrigerants.请遵照产品手册的选型准则来选取适合

特殊冷媒的产品

CSV 2, 3, 6
(NC solder)

(常闭 焊接接口)

Danfoss

32B01-CN-CSV

CSV 2,3,6
(NC flare)

(常闭 螺纹接口)

Danfoss

CSV 10, 15, 20, 22
(NC solder)

(常闭 焊接接口)

For CSV 3 and CSV 6 type valve, Danfoss recommends that a suitable filter or filter drier (max. size of 40 - 50 μm) is installed ahead of each solenoid
valve to keep scale, solder material and other foreign dirt and particles out of the valve.

注 意 ：对 于 CSV 3和CSV 6电磁阀，丹佛斯推荐在阀前安干燥过滤器（最大规格为 40-50μm 或其它过滤装置，以防止系统中的杂质、焊渣残留物以及
其它外部污垢和细小颗粒 进入阀体。

Mounting angle

安装角度

Danfoss

32B02-CN-CS

Danfoss

32B03-CN-CS0

032R9010

Danfoss

Soldering

焊接

Max. / 最高温度

700 °C / 1300 °F

Max. / 最高温度

100 °C / 212 °F

Min. 15% Ag 焊料最少含银量15%

Be sure that the
O-ring is in place

请确保O型圈安装在正
确的位置。

© Danfoss | DCS (sb) | 2020.10

Flare

螺纹

Danfoss

Danfo

To ensure correct sealing between coil and valve, mount the coil in
the proper position and make sure that the coil is fully clicked on to
the valve.

请确保密封圈正确安装于线圈和阀体之间,
并将线圈完全安装在阀体上，此时会听到‘咔’的一声。

Warning / 注意

Always disconnect power from
the coil when dismounted from
the valve.
The coil may be damaged
and there is risk of injuries and
burns.

当线圈没有完全安装在阀体上
时，禁止给线圈通电（拆除线圈
时，务必提前断电），否则会引
起线圈损坏甚至烧毁。

Danfoss

Danfo

32F869

AN34705422346901-000201 | 1