Danfoss CPI(R)-2933F Safety guide

CPI(R)-2933F (IBC) 5402036P01B
This material is to be used for research purposes only under the supervision of a technically qualified individual. The toxicological properties may have not been completely characterized. To determine your responsibilities under the EC Seventh amendment Directive 92 /32/EEC, please see the Regulatory Information Section. If this material has been supplied to you under the terms of a secrecy or non-analysis agreement, the information included in this MSDS is hereby identified as "Confidential Information."
Prepared according to Commission Regulation (EU) No 453/2010.
Section 1 Identification of substance/mixture and of the company/undertaking
CPI(R)-2933F (IBC) 5402036P01B - 160MPZ
Synonyms None.
1.2 Relevant identified uses of the substance or mixture and (uses advised against) Relevant identified uses (see section 7.3 for information on REACH registered uses)
Refrigeration Lubricants.
1.3 Details of the supplier of the safety data sheet
CPI Fluid Engineering 2300 James Savage Rd. Midland, MI 48642 Phone: 989-496-3780 Fax: 989-496-0316
E-mail contact EUSDS@lubrizol.com (Lubrizol Safety Data Sheets can be obtained at www.mylubrizol.com)
1.4 Emergency Telephone number
FOR TRANSPORT EMERGENCY call CHEMTREC: (+1) 703-527-3887 (outside the U.S.), 1-800-424-9300 (in the U.S.)
Section 2 Hazards Identification
2.1 Classification of the substance or mixture (EC) No 1272/2008
This product does not meet the classification requirements of the current European legislation.
67/548/EC or 1999/45/EC
This product does not meet the classification requirements of the current European legislation.
For a full text of R- and H- phrases: See section 16
2.2 Label elements (EC) No 1272/2008
Avoid release to the environment. All disposal practices must be in accordance with local, national and international regulations.
Supplemental label information
None.
2.3 Other hazards
None identified.
Section 3 Composition/Information on Ingredients
3.2 Mixtures
(EC) No 1272/2008
EC No. Registration Number Percentage (by wt.) Name Classification
204-881-4 01-2119565113-46 From 0 to 10.0 percent 2,6-Di-tert-butyl-p-cresol Aquatic Acute 1; H400
CPI(R)-2933F (IBC) 5402036P01B [2014/7/21]
Page1/7
Aquatic Chronic 1; H410
67/548/EC or 1999/45/EC
EC No. Registration Number Percentage (by wt.) Name Classification
67/548/EC
204-881-4 01-2119565113-46 From 0 to 10.0 percent 2,6-Di-tert-butyl-p-cresol N
R50/53
600, 700, 800 and 900 ECHA List Numbers do not have any legal significance; rather they are purely technical identifiers and are displayed for informational purposes only.
Section 4 First Aid Measures
4.1 Description of first aid measures Skin
Wash with soap and water. Get medical attention if irritation develops. Launder contaminated clothing before reuse.
Eyes
Flush with water at least 30 minutes. Get medical attention if eye irritation develops or persists.
Inhaled
Remove exposed person to fresh air if adverse effects are observed.
Swallowed
DO NOT INDUCE VOMITING. Get immediate medical attention.
Advice for first-aid providers
When providing first aid always protect yourself against exposure to chemicals or blood born diseases by wearing gloves, masks and eye protection. After providing first aid wash your exposed skin with soap and water.
4.2 Most important symptoms and effects, both acute and delayed
See section 11.
4.3 Indication of any immediate medical attention and special treatment needed
Note to physician: Treat symptomatically.
Section 5 Fire Fighting Measures
5.1 Extinguishing Media
CO2, dry chemical, or foam. Water can be used to cool and protect exposed material.
5.2 Special hazards arising from substance or mixture
See section 10 for additional information.
5.3 Advice for firefighters
Recommend wearing self-contained breathing apparatus.
Section 6 Accidental Release Measures
6.1 Personal precautions, protective equipment and emergency procedures
Personal protective equipment must be worn. Ventilate area if spilled in a confined space or other poorly ventilated area.
6.2 Environmental precautions
Take precautions to avoid release to the environment. Prevent from entering into soil, ditches, sewers, waterways and/or groundwater.
6.3 Methods and material for containment and cleaning up
Pick up free liquid for recycle and/or disposal. Residual liquid can be absorbed on inert material.
6.4 Reference to other sections
See sections 8 and 13 for additional information.
Section 7 Handling and Storage
7.1 Precautions for safe handling
Keep containers closed when not in use. Do not discharge into drains or the environment, dispose to an authorized waste collection point. Use appropriate containment to avoid environmental contamination. Wash thoroughly after handling. Launder contaminated clothing before reuse. Empty container contains product residue which may exhibit hazards of product. Dispose of packaging or containers in accordance with local, regional, national and international regulations.
CPI(R)-2933F (IBC) 5402036P01B [2014/7/21]
Page2/7
Pumping Temperature
Not determined.
Maximum Handling Temperature
Not determined.
Maximum Loading Temperature
Not determined.
7.2 Conditions for safe storage, including any incompatibilites
Take precautions to avoid release to the environment. See section 10 for incompatible materials.
Maximum Storage Temperature
Not determined.
7.3 Specific end use(s)
End uses are listed in an attached exposure scenario when one is required.
Section 8 Exposure Controls/Personal Protection
8.1 Control parameters
Country Substance Long Term (8 Hours T.W.A.) Short Term (15 mins.)
Austria 2,6-Di-tert-butyl-p-cresol 10 mg/cu. M N/E Denmark 2,6-Di-tert-butyl-p-cresol 10 mg/cu. M N/E Finland 2,6-Di-tert-butyl-p-cresol 10 mg/cu. M 20 mg/cu. M France 2,6-Di-tert-butyl-p-cresol 10 mg/cu. M N/E Greece Butyl-hydroxyl-toluene 10 mg/cu. M N/E Ireland 2,6-Ditertiary-butyl-para-cresol 10 mg/cu. M N/E Portugal 2,6-Di-tert-butyl-p-cresol 2 mg/cu. M N/E Slovenia 2,6-Di-tert-butyl-p-cresol 10 mg/cu. M N/E Switzerland 2,6-Di-tert-butyl-p-cresol 10 mg/cu. M 40 mg/cu. M Germany (TRGS 900) 2,6-Di-tert-butyl-p-cresol 10 mg/cu. M N/E UK 2,6-Di-tert-butyl-p-cresol 10 mg/cu. M 30 mg/cu. M
Other Exposure Limits
Contains synthetic basestock. Under conditions which may generate mists, observe the OSHA PEL of 5 mg per cubic meter, ACGIH TWA of 5 mg per cubic meter for mineral oil mists.
8.2 Exposure controls
Use with adequate ventilation.
Eye/face protection
Safety Glasses.
Skin protection
Neoprene. Long sleeve shirt is recommended. Launder contaminated clothing before reuse.
Respiratory Protection
Use respirator with a combination organic vapor and high efficiency filter cartridge if recommended exposure limit is exceeded. Use self-contained breathing apparatus for entry into confined space, for other poorly ventilated areas and for large spill clean-up sites.
Hygiene Measures
Wash thoroughly after handling this product.
Environmental exposure controls
See section 6 for details.
Section 9 Physical and Chemical Properties
9.1 Information on basic physical and chemical properties Appearance Clear to yellow liquid. Odour Mild Odour Threshold Not determined. pH Not determined. Melting / Freezing
Point
Not determined.
Boiling Point Not determined. Boiling Point Range Not determined.
CPI(R)-2933F (IBC) 5402036P01B [2014/7/21]
Page3/7
Flash Point 251°C,485.1°FCOC(Typical) Evaporation Rate Not determined. Flammability
(solid,gas)
Not applicable.
Lower flammability or explosive limit
Not determined.
Upper flammability or explosive limit
Not determined.
Vapour Pressure Not determined. Vapour Density Not determined. Relative density 0.98(20°C) Bulk Density 8.17 Lb/gal, 0.98 Kg/L Water Solubility Insoluble. Other solubilities Not determined. Partition coefficient:
n-octanol/water
Not determined.
Autoignition Point Not determined. Decomposition
Temperature
Not determined.
Viscosity 32.5Centistokes(40°C)
5.7Centistokes(100°C)
Explosive properties Material does not have explosive properties. Oxidising properties Material is a non-oxidising substance.
9.2 Other information
The above data are typical values and do not constitute a specification.
Section 10 Stability and Reactivity
10.1 Reactivity
Carefully review all information provided in sections 10.2 - 10.6.
10.2 Chemical stability
Material is normally stable at moderately elevated temperatures and pressures.
10.3 Possibility of hazardous reactions
Will not occur.
10.4 Conditions to avoid
Not determined.
10.5 Incompatible materials
Strong acids. Strong bases. Oxidizing agents.
10.6 Hazardous decomposition products
Smoke, carbon monoxide, carbon dioxide, aldehydes and other products of incomplete combustion.
Section 11 Toxicological Information
11.1 Information on toxicological effects
Acute toxicity
Oral
The LD50 in rats is > 2000 mg/Kg. Based on data from components or similar materials.
Dermal
The LD50 in rabbits is > 2000 mg/Kg. Based on data from components or similar materials.
Inhalation
No data available to indicate product or components may be a toxic inhalation hazard.
Skin corrosion / irritation
Not expected to be a primary skin irritant. Based on data from components or similar materials. Prolonged or repeated contact may cause dermatitis.
Serious eye damage / irritation
Not expected to cause eye irritation. Based on data from components or similar materials.
CPI(R)-2933F (IBC) 5402036P01B [2014/7/21]
Page4/7
Respiratory Irritation
If material is misted or if vapors are generated from heating, exposure may cause irritation of mucous membranes and the upper respiratory tract. Based on data from components or similar materials.
Respiratory or skin sensitization
Skin
No data available to indicate product or components may be a skin sensitizer.
Respiratory
No data available to indicate product or components may be respiratory sensitizers.
Germ cell mutagenicity
No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic.
Carcinogenicity
No data available to indicate any components present at greater than 0.1% may present a carcinogenic hazard.
Reproductive Toxicity
No data available to indicate either product or components present at greater than 0.1% that may cause reproductive toxicity.
STOT repeated exposure
No data available to indicate product or components present at greater than 1% are chronic health hazards.
Other information
No other health hazards known.
Section 12 Ecological Information
12.1 Toxicity
Freshwater fish
Not determined.
Freshwater invertebrates
The acute EC50 is 10 - 100 mg/L based on component data.
Algae
Not determined.
Saltwater fish
Not determined.
Saltwater invertebrates
Not determined.
Bacteria
Not determined.
12.2 Persistence and degradability
Substance Pct. (weight) Test type Duration (days) Pct. degradation
2,6-Di-tert-butyl-p-cresol From 0 to 10.0 percent MITI 2 14 30 2,6-Di-tert-butyl-p-cresol From 0 to 10.0 percent MITI 1 28 4.5
12.3 Bioaccumulative potential
Substance Pct. (weight) Test type Duration (days) Log Kow or BCF
2,6-Di-tert-butyl-p-cresol From 0 to 10.0 percent Octanol-Water Coefficient 0.1 5
12.4 Mobility in soil
Not applicable.
12.5 Results of PBT and vPvB assessment
Not Available
12.6 Other adverse effects
None known.
Section 13 Disposal Considerations
13.1 Waste treatment methods
All disposal practices must be in accordance with local, regional, national and international regulations. Do not dispose in landfill.
CPI(R)-2933F (IBC) 5402036P01B [2014/7/21]
Page5/7
Dispose of packaging or containers in accordance with local, regional, national and international regulations.
Section 14 Transport Information
14.1 UN number
ADR/RID Not regulated ICAO Not regulated IMDG Not regulated
14.2 UN proper shipping name
ADR/RID Not regulated ICAO Not regulated IMDG Not regulated
14.3 Transport hazard class(es)
ADR/RID Not regulated ICAO Not regulated IMDG Not regulated
14.4 Packing group
ADR/RID Not regulated ICAO Not regulated IMDG Not regulated
14.5 Environmental hazards
ADR/RID Not applicable. ICAO Not applicable. IMDG Not applicable.
14.6 Special precautions for users
Review classification requirements before shipping materials at elevated temperatures.
14.7 Transport in bulk according to Annex II of Marpol 73/78 and the IBC code
Not determined.
Section 15 Regulatory Information
15.1 Safety, health and environment regulations / legislation specific for the substance or mixture
Global Chemical Inventories
Australia All components are in compliance with chemical notification requirements in Australia. Canada All components are in compliance with the Canadian Environmental Protection Act and are present on the Domestic Substances List. China This product may require notification in China. EU To obtain information on the REACH compliance status of this product, please visit Lubrizol.com/REACH, or e-mail us at
REACH_MSDS_INQUIRIES@Lubrizol.com
Japan This product may be imported to Japan only by Lubrizol Japan. Korea All components are in compliance in Korea. New Zealand May require notification before sale under New Zealand regulations. Philippines All components are in compliance with the Philippines Toxic Substances and Hazardous and Nuclear Wastes Control Act of 1990 (R.A.
6969).
Switzerland All components are in compliance with the Environmentally Hazardous Substances Ordinance in Switzerland. Taiwan All components of this product are listed on the Taiwan inventory. USA All components of this material are on the US TSCA Inventory or are exempt.
German water hazard classes
WGK =1 according to the Water Hazardous Directive, VwVwS, dated May 17, 1999.
15.2 Chemical safety assessment
No chemical safety assessment has been carried out.
Section 16 Other Information
Created by
Product Safety and Compliance Department (440-943-1200)
Created Date
10 January 2011
CPI(R)-2933F (IBC) 5402036P01B [2014/7/21]
Page6/7
Revision date
21 July 2014
SDS No.
14346231-1125457-2095421-102103
HMIS Codes
Health Fire Reactivity
1 1 0
Relevant R Phrases
R50/53 -- Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Relevant hazard phrases
H400 - Very toxic to aquatic life. H410 - Very toxic to aquatic life with long lasting effects.
Revision Indicators
Section: 15 Phillppines. Changed: 7 February 2014 Section: 15 Taiwan Changed: 7 February 2014
As the conditions or methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of this product. Information contained herein is believed to be true and accurate but all statements or suggestions are made without warranty, expressed or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof. Compliance with all applicable federal, state, and local regulations remains the responsibility of the user.
CPI(R)-2933F (IBC) 5402036P01B [2014/7/21]
Page7/7
Loading...