Danfoss BD1.4F-FSD Data sheet

BD1.4F-FSD Direct Current Compressor R134a, 12-24V DC & 100-240V AC 50/60Hz

General

Code number (without electronic unit) 109Z0305

Electronic unit - Fixed Speed 101N2600, 30 pcs: 101N2601

Electronic unit - Fixed Speed w. AC/DC converter 101N5200, 30 pcs: 101N5201

Approvals VDE, UL, CCC, C-Tick

Compressors on pallet 180

Application

Application LBP/MBP

Evaporating temperature °C -30 to 0

Voltage range DC VDC 9.6 - 17 / 19 - 34

Voltage range AC V/Hz 100 - 240 / 50 - 60

Max. condensing temperature continuous (short)

Max. winding temperature continuous (short) °C 125 (135)

Cooling requirements

Application LBP MBP HBP

32°C S S –

38°C S S –

43°C S S –

Remarks on application:

°C 60 (70)

S = Static cooling normally sufcient O = Oil cooling F

= Fan cooling 1.5 m/s

(compressor compartment temperature equal to ambient temperature) F2 = Fan cooling 3.0 m/s necessary SG = Suction gas cooling normally sufcent – = not applicable in this area

Motor

Motor type permanent magnet, brushless DC

Speed rpm 3000

Resistance, all 3 windings (25°C) mΩ 210

Design

Displacement cm

Oil quantity (type) cm

Maximum refrigerant charge g 150

Free gas volume in compressor cm

Weight - Compressor/Electronic unit kg 2.1 / 0.11 (DC) / 0.29 (AC/DC)

Standard battery protection settings

Voltage (0.1 steps) Min. value Default Max. value

± 0.3V DC,

12V

all values

± 0.3V DC,

24V

all values

Dimensions

Height mm A 96.25

Suction connector location/I.D. mm | angle C 6.2 | 25°

Process connector location/I.D. mm | angle D 6.2 | 25°

Discharge connector location/I.D. mm | angle E 5.0 | 0°

Connector tolerance I.D. mm ±0.09, on 5.0 +0.12/+0.20

Cut out VDC 9.6 10.4 17

Cut in diff. VDC 0.5 1.3 10

Cut out VDC 19 21.3 27

Cut in diff. VDC 0.5 1.3 10

(refer to 101N2600/5200 Instructions for optional settings)

material | comment Cu-plated steel | Al cap

B 91.25

B1 88.00

B2 25.20

75 (polyolester)

1.41

500

September 2013 Manufactured by Secop for Danfoss - DEHC.ED.100.X4.02 / 520N1500 1/2

EN 12900 Household (CECOMAF)

Evap. temp. in °C -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 Capacity in W 4.7 13.2 16.4 23.3 35.2 49.4 60.1 66.0 85.4 Power cons. in W 15.7 22.6 24.8 28.8 34.5 39.6 42.8 44.4 48.7 Current cons. in A 1.30 1.73 1.88 2.16 2.57 2.98 3.24 3.37 3.76 COP in W/W 0.30 0.58 0.66 0.81 1.02 1.25 1.40 1.49 1.75

EN 12900 Household (CECOMAF)

Evap. temp. in °F -20 -13 -10 0 10 14 20 30 32 Capacity in W 6.5 13.2 16.4 28.3 42.8 49.4 60.2 80.9 85.4 Power cons. in W 17.3 22.6 24.7 31.4 37.4 39.6 42.8 47.8 48.7 Current cons. in A 1.40 1.73 1.88 2.34 2.80 2.98 3.24 3.68 3.76 COP in W/W 0.38 0.58 0.66 0.90 1.14 1.25 1.41 1.69 1.75

ASHRAE LBP

Evap. temp. in °F -20 -13 -10 0 10 14 20 30 32 Capacity in BTU/h 29.1 57.3 70.7 121.1 182.1 210 256 343 362 Power cons. in W 17.5 22.8 24.9 31.4 37.3 39.5 42.7 47.5 48.4 Current cons. in A 1.41 1.75 1.89 2.35 2.80 2.97 3.24 3.66 3.75 ERR in BTU/h 1.66 2.52 2.84 3.85 4.88 5.31 5.99 7.22 7.48

Operational errors (TOOL4COOL® or LED ashes)

Error code

or LED

ashes

Can be read out in the software TOOL4COOL®

Thermostat failure

(If the NTC thermistor is short-circuit or has no connection, the electronic unit will enter manual mode).

Thermal cut-out of electronic unit

(If the refrigeration system has been too hea vi ly loaded, or if the ambient tem pe ra ture is high, the electronic unit will run too hot).

Minimum motor speed error

(If the refrigeration system is too heavily loaded, the motor cannot maintain minimum speed at approximately 1,850 rpm).

Motor start error

(The rotor is blocked or the differential pressure in the refrigeration system is too high (>5 bar)).

Fan over-current cut-out

(The fan loads the electronic unit with more than

0.65A

peak

Battery protection cut-out

(The voltage is outside the cut-out setting).

Error type

ASHRAE LBP

Evap. temp. in °C -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 Capacity in W 6.4 16.8 20.8 29.2 44.0 61.5 74.8 82.2 106 Power cons. in W 16.0 22.8 24.9 28.9 34.5 39.5 42.6 44.2 48.4 Current cons. in A 1.32 1.75 1.89 2.16 2.57 2.97 3.23 3.37 3.75 COP in W/W 0.40 0.74 0.83 1.01 1.28 1.56 1.75 1.86 2.19

Test conditions EN 12900/CECOMAF ASHRAE LBP

Condensing temperature 55°C 54.4°C Ambient temperature 32°C 32°C Suction gas temperature 32°C 32°C Liquid temperature no subcooling 32°C

101N2600

Wire Dimensions DC

Size Max. length* Max. length*

Cross AWG 12V operation 24V operation

section

[mm

] [Gauge] [m] [ft.] [m] [ft.]

2.5 12 2.5 8 5 16 4 12 4 13 8 26 6 10 6 20 12 39

10 8 10 33 20 66

*Length between battery and electronic unit

Accessories for BD1.4F-FSD Code number

Bolt joint for one compressor Ø: 16 m m 118-1917 Bolt joint in quantities Ø :16 m m 118-1918 Snap-on in quantities Ø:16 m m 118-1919 Terminal cover for electronic unit 105N9120

Automoblie fuse DIN 7258

Main switch

12V: 15A 24V: 15A

min. 20A

Not

deliverable

from Secop

101N5200

refer to 101N2600 and 101N5200 Instructions for details

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

2/2 Manufactured by Secop for Danfoss - DEHC.ED.100.X4.02 / 520N1500 September 2013