Danfoss BD100CN Data sheet

BD100CN Direct Current Compressor R290 12-24V DC

General

Code number (without electronic units) 101Z0401

Electronic unit - High Speed 101N0290, 28 pcs: 101N0291

Approved compressor - electronic unit combinations refer to Instructions for 101N0290

Additional approvals e4, C-Tick

Compressors on pallet 150

Application

Application LBP

Evaporating temperature °C -40 to -10

Voltage/max. voltage VDC 9.6 - 17 / 21.3 - 31.5

Max. condensing temperature continuous (short)

Max. winding temperature continuous (short) °C 125 (135)

Cooling requirements

Application LBP MBP HBP

32°C S – –

38°C S – –

43°C S – – Remarks on application: for stationary use only

°C 55 (65)

S = Static cooling normally sufcient O = Oil cooling F

= Fan cooling 1.5 m/s

(compressor compartment temperature equal to ambient temperature) F2 = Fan cooling 3.0 m/s necessary SG = Suction gas cooling normally sufcent – = not applicable in this area

Motor

Motor type Variable speed

Resistance, all 3 windings (25°C) Ω 1.8

Design

Displacement cm

Oil quantity (type) cm

Maximum refrigerant charge g 120

Free gas volume in compressor cm

Weight - Compressor/Electronic unit kg 4.3/0.32

Standard battery protection settings

Voltage 12V 24V

Cut out VDC 10.4 22.8

Cut in VDC 11.7 24.2

Dimensions

Height mm A 137

Suction connector location/I.D. mm | angle C 6.2 | 40°

Process connector location/I.D. mm | angle D 6.2 | 45°

Discharge connector location/I.D. mm | angle E 5.0 | 21°

Connector tolerance I.D. mm ±0.09, on 5.0 +0.12/+0.20

Remarks

(refer to 101N0290 Instructions for optional settings)

material | comment Cu-plated steel | Al cap

150 (polyolester)

B 135

B1 128

B2 73

2.00

870

July 2013 Manufactured by Secop for Danfoss - DEHC.ED.100.H7.02 / 520N1482 1/2

Capacity (EN 12900 Household/CECOMAF) 12V DC, static cooling watt

rpm \ °C -40 -35 -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 2,500 30.6 40.2 51.9 66.0 71.4 82.9 103 126 3,100 36.0 49.0 64.6 83.0 90.0 105 130 160 3,800 40.5 56.6 75.6 98.0 106 124 154 189 4,400 44.6 62.4 83.4 108 117 137 170 209

Capacity (ASHRAE LBP) 12V DC, static cooling watt

rpm \ °C -40 -35 -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 2,500 34.1 44.8 57.9 73.6 79.7 92.5 115 141 3,100 40.1 54.6 72.0 92.6 100 117 145 178 3,800 45.1 63.1 84.3 109 119 138 172 211 4,400 49.7 69.6 93.0 121 131 153 190 233

Power consumption 12V DC, static cooling watt

rpm \ °C -40 -35 -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 2,500 35.7 39.8 44.8 50.5 52.5 56.4 62.3 67.8 3,100 41.9 48.9 56.3 64.0 66.7 71.8 79.4 86.5 3,800 48.7 58.6 68.6 78.5 81.8 88.1 97.5 106 4,400 57.4 69.1 80.8 92.5 96.4 104 115 125

Current consumption

(for 24V applications the following must be halfed) A

rpm \ °C -40 -35 -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 2,500 2.97 3.32 3.74 4.21 4.38 4.70 5.19 5.65 3,100 3.49 4.07 4.69 5.34 5.56 5.98 6.61 7.20 3,800 4.06 4.88 5.71 6.54 6.82 7.35 8.12 8.86 4,400 4.78 5.76 6.74 7.71 8.04 8.66 9.58 10.44

COP (EN 12900 Household/CECOMAF) 12V DC, static cooling W/W

rpm \ °C -40 -35 -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 2,500 0.86 1.01 1.16 1.31 1.36 1.47 1.65 1.86 3,100 0.86 1.00 1.15 1.30 1.35 1.46 1.64 1.85 3,800 0.83 0.97 1.10 1.25 1.30 1.41 1.58 1.78 4,400 0.78 0.90 1.03 1.17 1.22 1.32 1.48 1.66

COP (ASHRAE LBP) 12V DC, static cooling W/W

rpm \ °C -40 -35 -30 -25 -23.3 -20 -15 -10 -5 0 5 7.2 2,500 0.96 1.13 1.29 1.46 1.52 1.64 1.84 2.08 3,100 0.96 1.12 1.28 1.45 1.51 1.63 1.83 2.06 3,800 0.93 1.08 1.23 1.39 1.45 1.57 1.77 1.99 4,400 0.87 1.01 1.15 1.30 1.36 1.47 1.65 1.86

Test conditions EN 12900/CECOMAF* ASHRAE LBP*

Condensing temperature 45°C 45°C Ambient temperature 32°C 32°C Suction gas temperature 32°C 32°C Liquid temperature no subcooling 32°C

Operational errors errors shown by LED (optional)

Error code

Thermal cut-out of electronic unit

(If the refrigeration system has been too hea vi ly loaded, or if the ambient tem pe ra ture is high, the electronic unit will run too hot).

Minimum motor speed error

(If the refrigeration system is too heavily loaded, the motor cannot maintain minimum speed at approximately 2,450 rpm).

Motor start error

(The rotor is blocked or the differential pres-sure in the refrigeration system is too high (>5 bar)).

Fan over-current cut-out

(The fan loads the electronic unit with more than 1A

peak

Battery protection cut-out

(The voltage is outside the cut-out setting).

Error type

Compressor speed

Electronit unit Resistor

(R1) [Ω]

Code number

calculated

values [rpm]

Motor

speed

Control

circuit

current

[mA]

0 AEO 6

101N0290 with AEO

203 2,500 5 451 3,100 4 867 3,800 3

1700 4,400 2

In AEO (Adaptive Energy Optimizing) speed mode the BD comressor will always adapt its speed to the actual cooling demand.

Wire Dimensions DC

Size Max. length* Max. length*

Cross AWG 12V operation 24V operation

section

] [Gauge] [m] [ft.] [m] [ft.]

[mm

6 10 2.5 8 5 16

*Length between battery and electronic unit

Accessories for BD100CN Code number

Bolt joint for one compressor Ø :16 mm 118-1917 Bolt joint in quantities Ø: 16 mm 118-1918 Snap-on in quantities Ø:16 m m 118-1919 Remote kit (without cable) 105N9210

Standard automoblie fuse 12V: 30A DIN 7258 Main switch

24V: 15A

min. 30A

Not

deliverable

from Secop

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

2/2 Manufactured by Secop for Danfoss - DEHC.ED.100.H7.02 / 520N1482 July 2013