Daikin BYFQ60C3W1W, BYFQ60C3W1S Installation Manual
MODELS
BYFQ60C3W1W
BYFQ60C3W1S
INSTALLATION MANUAL
Decoration panel
English
Read these instructions carefully before installation.
Keep this manual in a handy place for future reference.
This manual should be left with the equipment owner.
Lire soigneusement ces instructions avant l’installation.
Conserver ce manuel à portée de main pour référence ultérieure.
Ce manuel doit être donné au propriétaire de l’équipement.
Lea cuidadosamente estas instrucciones antes de instalar.
Guarde este manual en un lugar a mano para leer en caso de tener alguna duda.
Este manual debe permanecer con el propietario del equipo.
Français
Español
6
1
2
4
3
1
A
B
90°
2 3
0.16-0.31 in. (4-8 mm)
1
3
2
4
5
2
3
1
7
5
13
1
2
3
A
B
4 5 7
2
6
2
1
4
6
3
5 (X105A)
BYFQ60C3W1W
BYFQ60C3W1S
Decoration panel
Installation manual
The English text is the original instruction. Other languages
are translations of the original instructions.
Read this manual attentively before installation. Do not throw
it away. Keep it in your les for future reference.
Improper installation or attachment of equipment or
accessories could result in electric shock, short-circuit,
leaks, re or other damage to the equipment. Be sure only to
use accessories made by Daikin that are specically
designed for the use with the equipment and have them
installed by a professional.
If unsure of installation procedures or use, always contact
your dealer for advice and information.
Before installation
Leave the unit inside its packaging until you reach the installation
site.
Rotary fan
Cut off the main power before opening the grille.
Refer to the installation manual of the indoor unit for items not
described in this manual.
NOTE
To the installer
Be sure to instruct the customer how to properly
operate the system showing him or her the operation
manual of the indoor unit.
Accessories
Installation manual
Screws (4x)
Grille hinge (2x)
Preparation before installation
For this unit, you are able to select airow directions. To discharge air
in 2 or 3 directions, it is necessary to purchase the optional blocking
pad kit for sealing air discharge outlets.
Handling of the decoration panel
To prevent any damage to the decoration panel, take care of the
following:
- Never place the decoration panel facing down.
- Never let the decoration panel lean against a wall.
- Never place the decoration panel on a sharp or projecting
object.
- Never touch or put pressure on the swing ap in order to
prevent malfunction of the swing ap.
Preparing the decoration panel for installation
1 Remove the suction grille from the decoration panel.
1 Decoration panel
2 Suction grille
3 Lever
Remove the transporting tape from the decoration panel suction
grille and aps.
Push the suction grille lever (3) inward and open the suction grille
(2). (See gure 1)
Detach the suction grille from the decoration panel by lifting the
suction grille up approximately 90 degrees (A) until the position is
reached on which removal of the suction grille is possible (B).
(See gure 2)
Installation of the decoration panel to the
indoor unit
Refer to the installation manual of the indoor unit for details on
installing the indoor unit.
1 Install the decoration panel (See gure 3)
1 Temporary latch
2 Hook
3 Swing ap motor lead wire
4 Piping area
5 Piping side mark
6 Drain area
7 Drain side mark
1 Hold the decoration panel against the indoor unit by matching the
piping side and drain side marks on the decoration panel with the
position of the piping area and drain area of the indoor unit.
2 Turn 2 panel temporary latches up into the hooks of the indoor
unit so the decoration panel is temporarily xed to the indoor unit.
(See gure 3)
3 Make sure that the swing ap motor lead wire isn’t caught
between the decoration panel and the indoor unit.
4 Attach 4 supplied screws and check whether the decoration
panel is properly aligned with the indoor unit and ceiling.
5 Tighten all 4 screws until the thickness between of the sealing
material between the decoration panel and the indoor unit
reduces to 0.16-0.31 in. (4-8 mm). (See gure 4)
1 Indoor unit
2 Ceiling
3 Sealing material
4 Decoration panel
5 Air outlet
English
1
Precautions
Improper tightening of the screws - (See gure 5) - may cause air to
leak into the unit and between the ceiling and the decoration panel
(1), resulting in formation of contamination (2) and dew (3).
If there is a gap remaining between the ceiling and the decoration
panel after tightening the screws, re-adjust the indoor unit body
height. The indoor unit must be kept leveled and the drain piping
kept unaffected.
2 Wiring of the decoration panel (See gure 6)
Make sure to turn off the power supply before wiring!
1 Screws (2)
2 Switch box
3 Swing ap motor lead wire
4 Swing ap motor lead wire xed by tie wrap to the rest of the wires
(See detail in gure 6)
5 Connector of the indoor unit PCB (X105A)
6 Tie wrap
1 Remove the electric components box lid. Loosen 2 screws and
slide the electric components box lid in the direction of the
arrows.
2 Securely connect the connector of swing ap motor lead wire
installed on the decoration panel. Attach the swing ap motor
lead wire to the rest of the wires rmly by tie wrap (from indoor
unit accessory set). (See gure 6)
3 Replace the electric components box lid reversing the procedure
to remove it.
Make sure that the swing ap motor lead wire is not
caught between the indoor unit and the decoration
panel and inbetween the electric component box lid.
Installation of the suction grille to
decoration panel
Install the suction grille (See gure 7)
1 Decoration panel
2 Suction grille
3 Suction grille hinge (attached to decoration panel)
1 Remove the transportation tape which is securing 2 suction grille
hinges in place.
2 Attach the suction grille to hinges by pressing the hinge and
inserting both ends of hinge to holes on the suction grille.
(See gure 7)
3 Make sure that the suction grille is attached to the decoration panel
properly by 2 hinges.
4 Close the suction grille by reversing the procedure shown in
“Preparing the decoration panel for installation” on page 1.
The suction grille may be installed in 4 directions by simply turning it
90 degrees.
Change the direction when adjusting the direction of the suction
grille of multiple units or to comply with the demands of the
customer.
2
English
Loading...