Daikin BYFQ60C2W1W, BYFQ60C2W1S, BYFQ60C4W1W, BYFQ60C4W1S Installation manuals

INSTALLATION MANUAL

Decoration panel

BYFQ60C2W1W BYFQ60C2W1S BYFQ60C4W1W BYFQ60C4W1S

4 5

90°

2 3

4-8 mm (0.16-0.31 in)

4 5 7

(X36A)

BYFQ60C2W1W

Rotary fan

1 Indoor unit

2 Ceiling

3 Sealing material

4 Decoration panel

5 Air outlet

BYFQ60C2W1S BYFQ60C4W1W BYFQ60C4W1S

Decoration panel

Installation manual

The English text is the original instruction. Other languages are translations of the original instructions.

Read this manual attentively before installation. Do not throw it away. Keep it in your files for future reference.

Improper installation or attachment of equipment or accessories could result in electric shock, short-circuit, leaks, fire or other damage to the equipment. Be sure only to use accessories made by Daikin that are specifically designed for the use with the equipment and have them installed by a professional.

If unsure of installation procedures or use, always contact your dealer for advice and information.

Before installation

 Leave the unit inside its packaging until you reach the

installation site.

Cut off the main power before opening the grille.

 Refer to the installation manual of the indoor unit for items not

described in this manual.

NOTE

Accessories

To the installer

Be sure to instruct the customer how to properly operate the system showing him or her the operation manual of the indoor unit.

Preparing the decoration panel for installation

1 Remove the suction grille from the decoration panel.

1 Decoration panel

2 Suction grille

3 Lever

 Remove the transporting tape from the decoration panel

suction grille and flaps.

 Push the suction grille lever (3) inward and open the suction

grille (2). (See figure 1)

 Detach the suction grille from the decoration panel by lifting

the suction grille up approximately 90 degrees (A) until the position is reached on which removal of the suction grille is possible (B). (See figure 2)

Installation of the decoration panel to the indoor unit

Refer to the installation manual of the indoor unit for details on installing the indoor unit.

1 Install the decoration panel (See figure 3)

1 Temporary latch

2 Hook

3 Swing flap motor lead wire

4 Piping area

5 Piping side mark

6 Drain area

7 Drain side mark

Installation manual

Screws (4x)

Grille hinge (2x)

Preparation before installation

For this unit, you are able to select air flow directions. To discharge air in 2 or 3 directions, it is necessary to purchase the optional blocking pad kit for sealing air discharge outlets.

Handling of the decoration panel

To prevent any damage to the decoration panel, take care of the following:

- Never place the decoration panel facing down.

- Never let the decoration panel lean against a wall.

- Never place the decoration panel on a sharp or projecting object.

- Never touch or put pressure on the swing flap in order to prevent malfunction of the swing flap.

Hold the decoration panel against the indoor unit by matching the piping side and drain side marks on the decoration panel with the position of the piping area and drain area of the indoor unit.

Turn 2 panel temporary latches up into the hooks of the indoor unit so the decoration panel is temporarily fixed to the indoor unit. (See figure 3)

Make sure that the swing flap motor lead wire isn’t caught between the decoration panel and the indoor unit.

Attach 4 supplied screws and check whether the decoration panel is properly aligned with the indoor unit and ceiling.

Tighten all 4 screws until the thickness between of the sealing material between the decoration panel and the indoor unit reduces to 4-8 mm. (See figure 4)

BYFQ60C2W1(W/S) + BYFQ60C4W1(W/S) Decoration panel 4P340850-1D – 2020.04

Installation manual

+ 5 hidden pages