Daikin BYCQ140E2W1, BYCQ140E2W1W, BYCQ140E2W1B Installation manuals
INSTALLATION MANUAL
Decoration panel
BYCQ140E2W1
BYCQ140E2W1W
BYCQ140E2W1B
23
1
2
4
2
a
b
3
a
b
≤
c
b
3
e
2
b
415
1
5
3
1
1
45
2
2
5
2
3
1
4
4+6
5
6
g
1
1
f
d
5
g
2
4
65
1
3
h
g
12 mm
a
6
3 4
44355
8
126
7
1
9
2×
8×
1
2
10
4×
4×
BYCQ140E2W1
BYCQ140E2W1W
BYCQ140E2W1B
Decoration panel
Installation manual
■ The BYCQ140E2W1W has white insulations.
Be informed that formation of dirt on white insulations
is visibly stronger and that it is consequently not
advised to install the BYCQ140E2W1W decoration
panel in environments exposed to concentrations of
dirt.
When using the BYCQ140E2W1W decoration panel it
is advised to change the filter cleaning display
indications on the remote controller from light to
heavy. Changing the setting to heavy corresponds to
filter cleaning display indications in case of higher
contamination of the air. Refer to the indoor unit
installation manual under paragraph "setting air filter
sign" or "field setting", depending on the type of indoor
unit.
■ Read this manual attentively before installation. Do
not throw it away. Keep it in your files for future
reference.
Improper installation or attachment of equipment or
accessories could result in electric shock, shortcircuit, leaks, fire or other damage to the equipment.
Be sure only to use accessories made by Daikin
which are specifically designed for the use with the
equipment and have them installed by a professional.
If unsure of installation procedures or use, always
contact your dealer for advice and information.
The English text is the original instruction. Other languages are
translations of the original instructions.
- Never touch or put pressure on the swing flap in order to
prevent malfunction of the swing flap.
- Be careful not to damage the 4 tabs at
the back of the corner decoration cover.
Preparing the decoration panel for installation
1 Remove the suction grille from the decoration panel.
■ Push the suction grille lever (5) inward and open the grille (2).
(See figure 1)
1 Decoration panel
2 Suction grille
3 Corner decoration cover
4 Swing flaps
5 Lever
■ See figure 2. Detach the suction grille from the decoration
panel by lifting the grille up approximately 45 degrees (1) until
the position is reached on which removal of the grille is
possible (2).
■ Remove the transporting cardboard (3) from the decoration
panel (in 4 locations).
■ Remove the transporting tape (4) from the back of the suction
grille (5) (in 4 locations).
Before installation
■ Leave the unit inside its packaging until you reach the
installation site.
■ Refer to the installation manual of the indoor unit for items not
described in this manual.
NOTE
To the installer
Be sure to instruct the customer how to properly
operate the system showing him or her the
operation manual of the indoor unit.
Accessories
1× 1×4× 4× 4×
Preparation before installation
For this unit, you are able to select air flow directions. To discharge
air in 2 or 3 directions, it is necessary to purchase the optional
blocking pad kit for sealing air discharge outlets.
Handling of the decoration panel
To prevent any damage to the decoration panel, take care of the
following:
- Never place the panel facing down.
- Never let the panel lean against a wall.
- Never put it down on a projecting object.
2 Remove the corner decoration cover on each corner by pulling it
up in the direction of the arrow. (See figure 3)
Installation of the decoration panel to the indoor unit
Refer to the installation manual of the indoor unit for details on
installing the indoor unit.
1 Install the decoration panel (See figure 5)
a Mounting bracket
b Hook
c Piping section
d "Piping side" marking
e Drain section
f "Drain side" marking
g Temporary latch
h Swing flap motor lead wire
1 Hold the decoration panel against the indoor unit by matching the
piping side and drain side marks on the decoration panel with the
position of the piping section and drain section of the indoor unit.
2 Temporarily install the decoration panel to the indoor unit by hanging
the temporary latch into the hooks of the indoor unit body. (2
locations)
3 Hook the 4 mounting brackets on the corner sections of the
decoration panel onto the hooks around the indoor unit body.
Make sure that the swing flap motor lead wire is not caught between
the indoor unit and the decoration panel.
4 Screw all 4 hexagon head screws located in the corner section in for
approximately 5 mm. The panel will rise.
5 Adjust the decoration panel by turning it in the direction indicated by
the arrows on the figure so that the ceiling opening is completely
covered.
BYCQ140D7W1 + BYCQ140D7W1W
Decoration panel
4P552012-1A 2018.12
Installation manual
1
Loading...