Daewoo MAYTAG User Manual

TOP FREEZER

Table of Contents

Important Safety Instructions.... 1-2

Installation ..................................... 3-6

Temperature Controls ...................... 7

Looking Inside

Ice Service ....................................... 10

Food Storage Tips .................... 11-13

Form No. E/11/05 Part No. 3013912910 www.maytag.com

............................... 8-9

Use & Care Guide

Storing the Refrigerator................ 14

Care & Cleaning ....................... 14-15

Troubleshooting........................ 16-18

Warranty & Service ........................ 19

Guide d’utilisation et

d’entretien

Guía de uso y Cuidado.................. 40

................................... 20

Important Safety Instructions

Installer: Please leave this manual with this appliance.

onsumer:Please read and keep this Use & Care Guide

for future reference. This manual provides proper use and maintenance information.

Keep sales receipt and/or cancelled check as proof of purchase.

If you have questions, call:

1-800-688-9900 U.S.A. or 1-800-688-2002 Canada 1-800-688-2080 (U.S. TTY for hearing or speech impaired) (Mon.-Fri., 8 a.m.-8 p.m. Eastern Time)

Have complete model and serial number identification of your refrigerator. This is located on a data plate inside the refrigerator compartment, on the upper left side. Record these numbers below for easy access.

Model Number ____________________________________

Serial Number_____________________________________

Date of Purchase __________________________________

In our continuing effort to improve the quality and performance of our appliances, it may be necessary to make changes to the appliance without revising this guide.

What You Need to Know About Safety Instructions

Warning and Important Safety Instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining or operating appliance.

Always cont manufacturer about problems or conditions you do not understand.

act your dealer

, distributor

, service agent or

DANGER

To reduce risk of injury or death, follow basic precautions, including the following:

IMPORTANT:

are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they sit out for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors. Leave the shelves in place so

• children may not easily climb inside.

This appliance is equipped with a three-pronged grounding plug for your protection against possible electric grounding receptacle. Where a standard two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded three-prong wall receptacle. Do not under any circumstances, cut or remove the third (ground) prong from the power cord. Do not use an adapter plug.

al shock hazards. It must be plugged into a

Power supply cord with

three-prong grounding plug

Child entrapment and suffocation

Recognize Safety Symbols, Words, Labels

DANGER

DANGER – Immediate hazards which WILL result in severe personal injury or death.

WARNING

WARNING – Hazards or unsafe practices which

OULDresult in severe personal injury or death.

CAUTION

CAUTION – Hazards or unsafe practices which

ULD

damage.

sult in minor personal injury or proper

Grounding type

wall receptacle

Important Safety Instructions

WARNING

To reduce risk of fire, electric shock, serious injury or death when using your refrigerator, follow these basic precautions, including the following:

13. Always disconnect refrigerator from electrical supply before attempting any service. Disconnect power cord by grasping the plug, not the cord.

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not sure this appliance is properly grounded.

5. Do not ground to a gas line.

6. Do not ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate 115 volt, 15 amp., 6

8. Do not modify plug on power cord. If plug does not fit electrical outlet, have proper outlet installed by a qualified electrician.

9. Do not use a two-prong adapter, extension cord or power strip.

Do not remove warning tag from power cord.

10.

11. Do not tamper with refrigerator controls.

12. Do not service or replace any par unless specific Guide or published user-repair instructions. Do not attempt service if instructions are not understood or if they are beyond personal skill level.

0 cycle line.

t of refrigerator

ally recommended in Use & Care

14. Install refrigerator according to Installation Instructions. All connections for water, electrical power and grounding must comply with local codes and be made by licensed personnel when required.

15. Keep your refrigerator in good condition. Bumping or dropping refrigerator can damage refrigerator or cause refrigerator to malfunction or leak. If damage occurs, have refrigerator checked by qualified service technician.

16. Replace worn power cords and/or loose plugs.

17. Always read and follow manufacturer’s storage and ideal environment instructions for items being stored in refrigerator.

Your refrigerator should not be operated in the

18. presence of explosive fumes.

Children should not climb, hang or stand on any

19. part of the refrigerator.

20. Clean up spills or water leakage associated with water inst

allation.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Installation

Your new refrigerator was packed carefully for shipment. Remove and discard shelf packing and tape.

Location

• Allow for a free flow of air through the front base grille.

• Install the refrigerator where the room temperature will not go below 55° F (13° C). With temperatures below 55° F (13° C), the refrigerator will not run frequently enough to maintain proper temperature in the freezer.

• Allow a minimum back for ease of installation. If refrigerator is placed with the door hinge side against a wall, you may want to allow additional space so the door can be opened wider.

• Use caution when installing the unit on vinyl or hardwood floors so as not to mark or otherwise damage the flooring. A piece of plywood, a rug or other material should be used to protect the floor while positioning the unit.

Leveling

To enhance its appearance and to maintain performance, your refrigerator should be leveled after it has been rolled into its final loc

• Adjust the leveling/lock screws beneath each front corner at the base of the cabinet. Turn these leveling/lock screws clockwise to raise a cabinet corner and counterclockwise to lower a cabinet

corner

⁄2" clearance on the sides, top and

ation.

TURN CLOCKWISE TO

RAISE CABINET CORNER

URN COUNTER-CLOCKWISE TO

Figure 2

OWER CABINET CORNER

Front Base Grille (on select models)

The front base grille (select models) which was packaged inside the refrigerator for shipment and should be installed after the refrigerator has been leveled.

“Snap on” style:

• To install, align the spring clips with the round openings in the cabinet and push each end in until the grille locks into place.

• To remove this style of base grille, grasp both ends and pull straight out.

“Screw on” style:

• Use a Phillips screwdriver to remove the two Phillips head screws at the base of the refrigerator.

• Align the base grille to the screw holes. (The cut out side on the base grille installs around the lower hinge of the door

• Secure the base grille into place by reinstalling the Phillips screws back into their original screw holes.

Reverse the

•

se steps to remove this style of base grille.

Energy Saving Tips

• Locate the refrigerator away from heat producing

appliance vents and direct sunlight.

s such as the range or dishwasher

, heat

o raise

To lower

cabinet

• If the floor is not level and it is necessary to raise the rear of the c wheels onto a piece of plywood or other shim material.

• Refrigerator models that have adjustable wheels can be leveled by removing the base grille and adjusting the wheels with a 1/ figure 2.)

abinet, we sugge

4" socket or screwdriver. (See

st rolling the rear

T cabinet

• Level the refrigerator and do not block ventilation around the front base grille.

et hot dishe

• refrigerator or freezer.

Cover liquids.

•

• Keep the freezer full to near capacity so less cold air will escape during door openings. When the freezer is

ss than

le the freezer

•

Wipe moisture from the outside of containers before placing them into the refrigerator.

• Avoid opening the doors too often.

s cool slightly before putting into the

⁄3 full, place milk c

artons half full of water in

Installation

WARNING

To avoid electrical shock which can cause severe personal injury or death:

• Disconnect power to refrigerator before reversing doors.

Reversing Doors

Tools Required:

•

⁄1

" end wrench

• Phillips screwdriver

• Putty knife

•

⁄16" socket and ratchet

Unplug the refrigerator.

1. Pry off hinge cap with a putty knife and set aside.

2. With a

the upper hinge and set aside.

3. Carefully lift and remove freezer door (including the

upper hinge) off the center hinge.

4. With a

and middle hinge from the top of refrigerator door. With a putty knife, pry out the plug buttons and replace them on the opposite side.

⁄16" socket and ratchet, remove screws from

⁄16" socket and ratchet, remove the screws

14. Attach the middle hinge with the screws removed from the opposite side and secure them using a wrench.

15. Carefully place freezer door on top of hinge arm. Use foam door spacer to set gap.

Note

• Do not discard the foam door spacer. Doors may settle with use.

16. Slide top hinge into place on freezer door and secure screws with

Confirm that all screws have been tightened securely.

17. Snap hinge cap securely in place. Replace front base grille (see p. 3).

18.

Remember to plug in your refrigerator and reset the controls to the appropriate setting(s).

⁄16" wrench.

⁄16”

Carefully lift and remove refrigerator door.

6. Remove front base grille and set aside (see p. 3).

7. With a

⁄16" socket and ratchet, remove hinge plate

from lower corner of refrigerator and secure it on the opposite side.

8. Remove plate from the underside of refrigerator door and secure it on the opposite side with a

⁄16"

socket and ratchet.

9. With a

⁄16" socket and ratchet, remove the door

stop from the underside of the freezer door and secure it on the opposite side.

10. With a putty knife, pry out the plug button(s) from tops of freezer and refrigerator doors and replace them on the opposite side.

Remove screw hole plugs from top of c

11.

abinet and

replace on the opposite side.

12. With a

⁄16" socket and ratchet, remove washers and

stem from the inside of the hinge plate and place them on the outside of the hinge plate.

13. Carefully replace refrigerator door on the hinge plate in lower corner

Installation

Note: P

installation.

hillips screw driver is required for

Freezer Door Handle Installation

STEP 1

Fasten with screw

STEP 2

Align handle

HANDLE

STEP 3

Rotate handle

with mounting screw

SCREW

STEP 4

Secure bottom end of handle with two screws.

SCREW

Refrigerator Door Handle Installation

STEP 1

Fasten with screw

STEP 2

Align handle

HANDLE

with mounting screw

STEP 3

Push handle down

CREW

STEP 4

Secure top end of handle with two screws

SCREW

Do not over-tighten

Reversing Door Handles

To remove the handles, reverse the above steps. Flip the handles 180° and mount them on the opposite doors.

Do not over-tighten

Installation

Connecting the Water Supply

(select models)

WARNING

To reduce the risk of injury or death, follow basic precautions, including the following:

• Read all instructions before installing ice maker.

• Do not attempt installation if instructions are not understood or if they are beyond personal skill level.

• Observe all local codes and ordinances.

• Do not service ice maker unless specifically recommended in Use & Care Guide or published user-repair instructions.

• Disconnect power to refrigerator before installing ice maker.

• Water damage due to an improper water connection may cause mold/mildew growth. Clean up spills or leakage immediately.

Materials Needed

•

⁄4" outer diameter flexible copper tubing

• Shut-off valve (requires a water supply line before valve attachment)

• Adjustable wrench

•

⁄4" hex nut driver

⁄4" hole to be drilled into

Note

• Add 8' to tubing length needed to reach water supply for creation of service loop.

1. Create service loop with copper

tubing (minimum 2’ diameter). Avoid kinks in the copper tubing when bending it into a service loop.

2. Remove plastic cap from water valve inlet

port.

2’ diameter

minimum

CAUTION

To avoid property damage or possible injury, follow basic precautions, including the following:

• Consult a plumber to connect

tubing to household plumbing to assure compliance with loc

•

Confirm water pressure to water valve is between 35 and 100 pounds per square inch. 20 pounds per square inch if there is not a water filter.

Do not use a self-piercing, or

• Both reduce water flow and can become clogged over time, and may c attempted.

• Tighten nuts by hand to prevent cross threading. Finish tightening nuts with pliers and wrenches. Do not overtighten.

ait 2-3 hours before placing refrigerator into final

• position to check and correct any water leaks. Recheck for leaks after 24 hours.

erify the copper tubing under the sleeve is

• smooth and free from defects. Do not reuse an old sleeve.

al code

ause leaks if repair is

⁄4” O.D. copper

s and ordinance

addle valve.

⁄16" s

3. Place brass nut (A) and sleeve (B) on copper tube end as illustrated. Reminder: Do not use an old sleeve.

4. Place end of copper tubing into water valve inlet port. Shape tubing slightly straight into inlet port.

5. Slide brass nut over sleeve and screw nut into inlet port. Tighten nut with wrench.

IMPORTANT: Do not overtighten. Cross threading may occur.

6. Pull on tubing to confirm connection is secure. Connect tubing to frame with water tubing clamp (C) and turn on water supply. Check for leaks and correct if necessary. Continue to observe the water supply connection for two to three hours prior to moving the refrigerator to it loc

7. Monitor water connection for 24 hours. Correct leaks, if necessary.

. Do not kink – so that tubing feeds

s permanent

ation.

Temperature Controls

COLDEST COLD

FREEZER CONTROL

INITIAL SETTING

In some models the fresh food control is located at the top of the fresh food compartment and the freezer control is located at the back of the freezer compartment as show below:

In other models, both controls are loc the fresh food compartment as shown below:

ated at the top of

• Except when starting the refrigerator, do not change either control more than one number at a time.

• Allow 24 hours for temperatures to stabilize before resetting.

• Changing either control will have some effect on the temperature of the other compartment.

TEMPERATURE CONTROL GUIDE

Fresh Food Compartment too Warm

Fresh Food Compartment too Cold

Freezer too Warm

Freezer too Cold

Turn Refrigerator “OFF”

Adjust fresh food control to next higher setting.

Adjust fresh food control to next lower setting.

Adjust freezer control to next colder setting.

Adjust freezer control to next warmer setting.

Set fresh food control to “OFF”.*

Initial Settings

• The fresh food control has settings from 1 (cold) to 7 (colde

• The freezer control, when located at the back of the freezer, has settings from cold to coldest. Initially set this control at the mid-line initial setting.

• When the freezer control is located at the top of the fresh food compartments, it has settings from 1 (cold) to 7 (coldest). Initially set this control on 4.

st). Initially set this control on 4.

Note

• Your refrigerator will run continuously for several hours when you first start it. This is normal.

• Let the refrigerator run at least four hours before adding food.

Adjusting the Temperature Controls

• 24 hours after adding food, you may decide that one or both compartments should be colder or warmer. If so, adjust the control(s) as indicated in the following

able.

* Turning the fresh food control to “OFF” stops cooling

in both compartments. It does not shut off power to the refrigerator.

No Defrosting

Your refrigerator is designed to defrost automatically.

Note

During the automatic defrost c

• a red glow/reflection in the vents on the back wall of the freezer compartment and you may hear the sound of water droplets coming into contact with the defrost heater. This is normal during the defrost c

ycle.

ycle, you may notice

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be warm to the touch. This is a normal occurrence that helps prevent moisture from condensing on the cabinet. The condition will be more noticeable when you first start the refrigerator, during hot weather and after exce

ssive or lengthy door openings.

Looking Inside

Fresh Food Compartment

Shelves (style may vary)

CAUTION

To avoid personal injury or property damage:

• Never attempt to adjust a shelf when it is loaded with food.

• Confirm that shelf is secure prior to loading items onto it.

• Handle glass shelves with care. Shelves may break suddenly if nicked, scratched or exposed to sudden temperature changes.

Select models are equipped with wire or glass full width shelves that are supported by rails molded into the interior walls of the fresh food compartment. These shelves can easily be adjusted to alternate positions within the compartment.

To Adjust a Full Width Shelf:

The bucket-style container sizes and shapes.

To Remove:

• Grasp the shelf on each end.

• Lift the shelf up and out.

To Reinstall:

• While holding the shelf on each end, slide the shelf in and down.

• Push down on the interior center of the shelf to snap it completely into place.

The Crispers provide a storage area for fruit and vegetables. Some crisper drawers have slide humidity controls.

Door Shelves accommodate a variety of

• Grasp each side of the shelf.

• Pull the shelf forward approximately 1".

• While suppor shelf from underneath, lift it up and out.

• Slide the shelf into the

sired alternate

de position.

Shelves in other models hook into support rails located on the back wall of the fresh food compartment.

To Remove:

• Slightly tilt up the front and lift up the rear of the shelf pull the shelf straight out.

To Lock Into Another Position:

• Tilt up the front edge of the shelf.

• Insert the hooks into the desired frame openings and let the shelf settle into place.

Be sure the shelf is securely locked at the rear

• On cer

• on rails formed into the side of the fre compartment.

ting the

, then

tain models the outside edge of the shelf rests

sh food

For fruit storage, slide the control (select models) to the left to provide lower humidity conditions in the drawer.

For vegetable storage, slide the control (select models) to the right to provide higher humidity conditions in the drawer.

For best results, keep the crispers tightly closed.

To Remove:

ull out the crisper until it stops.

•

• Tilt the drawer up slightly and pull it out.

To Reinstall:

ith the drawer tilted up slightly

• tracks and slide in.

The

Crisper Top serves as the lower refrigerator shelf.

o Remove:

• Remove the crisper drawers. Slightly lift up the front of the shelf.

• Suppor

• of the cabinet.

To Reinstall:

• With the shelf front tilted slightly upward, carefully insert the crisper top back into the c

• let the crisper top settle into place.

t the shelf from underneath to lift it up and then out

osition the rear and side

s of the shelf on the suppor

, align the drawer in the

abinet.

s and

Looking Inside

Can Rack (select models)

The Can Rack slides out from underneath a shelf. It can hold up to twelve 12-ounce beverage cans.

To Remove:

• Pull rack out to full extension. Tilt up the front of rack and pull straight out.

To Install:

• Insert rack into frame rails and push back into place.

Tall Bottle Retainer/Snugger

(select models)

The Tall Bottle Retainer prevents tall bottles from

ainer

tipping forward. T can be placed above any removable door bucket.

he Ret

Freezer Compartment

CAUTION

To avoid personal injury or property damage:

• Never attempt to adjust a shelf when it is loaded with food.

• Confirm that shelf is secure prior to loading items onto it.

Some refrigerators have a full-width shelf in the freezer compartment. This shelf can be adjusted to accommodate a variety of frozen food loads.

To Adjust the Shelf:

• Slide the shelf to the left.

• Lift the left support bars out of the wall support cups.

• Reposition the shelf in the alternate position.

The

Snugger attached to the Tall Bottle Retainer keeps

s and other containers in place when the door is

bottle opened or closed. Adjust the Snugger by sliding from side to side. Select models also feature snuggers in the door bucket itself.

Egg Tray With Handle

(style may vary/select models)

The Egg Tray with Handle holds a “dozen-plus” eggs. It can be removed to carry to a work area or to be washed.

Dairy Compartment

Dairy Compartment is

covered and designed to store spreadable food items such as butter or margarine.

o use this compar

T raise the lid to store or retrieve items.

tment, simply

The Slide Out F found in the main freezer compartment. It is a convenient storage area, providing easy access to items stored in the rear of the freezer out to reach or store frozen foods.

emov

o r

•

ull the basket until it stops.

• Lift and pull the basket out. To replace the basket, reverse the removal procedure.

T found on the lower shelf of the freezer door provides space for frozen food items that tend to shift or slide (such as bagged vegetables).

op Down F

reezer Basket

e the basket:

eezer Basket

(select models) is

. Slide the basket

(select models) is

his area

. T

This compartment can be removed for cleaning. Rotate the cover open. Grasp the dairy compartment from the bottom and lift out.

On select models, this compar on the left or right side of the door

tment c

an be inst

alled

Ice Service

OFF

100

ICE

100

10 0

ICE

LEVE L

ICE

LEVE L

10 0

Ice Cube Trays

Select models are equipped with ice cube trays. To release the ice cubes from a tray, hold the tray upside down over a container and twist both ends.

Automatic Ice Maker (optional)

Note

• Energy rating guides that are posted on the refrigerator at the time of purchase do not include optional ice maker energy usage.

Select models are automatic ice maker ready. The number of the appropriate ice maker kit needed for

allation into these models appears on the data

inst plate. The kit contains installation instructions and water connection instructions.

Other models have a factory installed ice maker. Connect the ice maker to the water supply as

instructed in the separate instructions furnished with the ice maker.

refrigerator is essential for optimal ice maker performance.

After your refrigerator has been connected to the water supply, move the sensor arm into the down position. The ice maker will fill with water when the freezer reache

s the proper temperature.

Some ice makers are equipped with an adjustable sensor arm that allows you to adjust the amount of ice in your ice storage tray for time needed.

Proper water flow and a level

s when le

Wire Lever Arm

ss ice is

• When the ice cubes are ejected it is normal for several cubes to be joined together at the ends. They can easily be broken apart. The ice maker will continue to make ice until the supply of ice cubes raises the sensor arm, shutting the ice maker off.

• Certain sounds may accompany the various cycles of the ice maker. The motor may have a slight hum, the cubes will rattle as they fall into an empty storage pan and the water valve may click or “buzz” occasionally.

• If the ice is not used frequently, the ice cubes will become cloudy, shrink, stick together and taste stale. Empty the ice storage bin periodically and wash it in lukewarm water. Be sure to dry the bin before replacing it.

• To remove the ice bin, pull it forward, away from the ice maker. To avoid the ice maker dumping ice while the bin is removed, turn the ice maker off by lifting the sensor arm.

• To replace the ice bin, reverse the above procedure. Turn the ice maker on by lowering the sensor arm.

• Beverage and foods should not be placed in the ice storage bin for quick chilling. These items can block the sensor arm, causing the ice maker to malfunction.

• Turn off (arm up) the ice maker when the water supply is to be shut off for several hours.

WARNING

To avoid personal injury or property damage:

Do not place fingers or hands on the automatic ice

• making mechanism while the refrigerator is plugged in. This will help protect you from possible injury. It will also prevent interference with moving parts of the ejector mechanism and the heating element that release

s the cube

Sensor

Arm

To adjust the amount of ice produced: (select models) Rotate the wire lever arm to provide the desired level of ice production. The 100% setting provide

•

s maximum ice production.

It may be 8 to 12 hours before the ice maker furnishe

s any usable ice cubes. The first one or two batches will probably contain undersized and irregular cube

he initial batch may also cont

• new water supply piping. Therefore, all cubes from the first two or three batches should be discarded.

ause of air in the supply line.

s bec

ain impuritie

s from the

• Under certain rare circumstances, ice cubes may be discolored, usually appearing with a greenbluish hue. The cause of this unusual discoloration can be a combination of factors such as certain characteristics of loc

al waters, household plumbing and the accumulation of copper salts in an inactive water supply line which feeds the ice maker. Continued consumption of such discolored ice cubes may be injurious to health. If such discoloration is observed, disc and cont

act your dealer to purchase and install a

ard the ice cube

water line filter.

ater damage due to improper water connection

• may cause mold/mildew growth.

Food Storage Tips

Fresh Food Storage

• The fresh food compartment of a refrigerator should be kept between 34° F (1° C) and 40° F (4° C) with an optimum temperature of 37° F (3° C). To check the temperature, place an appliance thermometer in a glass of water and place in the center of the refrigerator. Check after 24 hours. If the temperature is above 40° F (4° C) adjust the control as explained on page 7.

• Avoid overcrowding the refrigerator shelves. This reduces the circulation of air around the food and results in uneven cooling.

Fruits and Vegetables

• Storage in the crisper drawers traps humidity to help preserve the fruit and vegetable quality for longer time periods (see page 8).

• Sort fruits and vegetables before storage and use bruised or soft items first. Discard those showing signs of decay.

• Always wrap odorous foods such as onions and cabbage so the odor does not transfer to other foods.

Frozen Food Storage

• The freezer compartment of a refrigerator should be kept at approximately 0° F (-18° C). To check the temperature, place an appliance thermometer between the frozen packages and check after 24 hours. If the temperature is above 0° F (-18° C), adjust the control as explained on page 7.

• A freezer operates more efficiently when it is at least

⁄3 full.

Packaging Foods for Freezing

• To minimize dehydration and quality deterioration use aluminum foil, freezer wrap, freezer bags or airtight containers. Force as much air out of the packages as possible and be sure they are tightly sealed. Trapped air can cause the food to dry out, change color and develop an off-flavor (freezer burn).

• Overwrap fresh meats and poultry with suitable freezer wrap prior to freezing.

•

Do not refreeze meat that has completely thawed.

Loading the Freezer

s need a certain amount of humidity

• While veget to remain fresh, too much moisture can shorten storage time veget

able

s (especially leafy items). Drain

ables well before storing.

Meat and Cheese

• Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or

faces does not occur.

sur

• Occasionally mold will develop on the surface of

wiss, Cheddar

s (S

hard chee least an inch around and below the moldy area. K your knife or instrument out of the mold it

Do not try to save individual cheese slices, soft cheese,

age chee

cott mold appears.

se, cream, sour cream or yogurt when

, Parmesan). Cut off at

eep

self.

Dairy Food

Most dairy foods such as milk, yogur

• and cott cartons for appropriate length of storage. Store these foods in the original carton and refrigerate immediately after purchasing and after each use.

age cheese have freshness dates on their

t, sour cream

• Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing and can raise the temperature of frozen foods.

• Leave a space between the packages so cold air can circulate freely possible.

• Avoid storing hard-to-freeze foods such as ice cream and orange juice on the freezer door shelves. These foods are best stored in the freezer interior where the temperature varie

, allowing food to freeze as quickly as

ss with door openings.

s le

Food Storage Tips

Food Storage Chart

Storage times are approximate and may vary depending on type of packaging, storage temperature, and the quality of the food when purchased.

FOODS DAIRY PRODUCTS

Butter Milk and cream

Cream cheese, cheese spread and cheese food

age cheese

Cott

Sour cream

Hard cheese (Swiss, Cheddar and Parmesan)

EGGS

Eggs in the shell Leftover yolks or whites

FRUITS

Apples

REFRIGERATOR

1 month

1 week

1-2 weeks

3-5 days

10 days

1-2 months

3 weeks 2-4 days

1 month

FREEZER

6-9 months

Not recommended

4-6 months

May become crumbly

Not recommended

9-12 months

8 months (cooked)

STORAGE TIPS

Wrap tightly or cover. Check carton date. Close tightly.

Don’t return unused portions to original container. Don’t freeze cream unless whipped.

Wrap tightly.

Store in original c carton date.

Wrap tightly. Cut off any mold.

Refrigerate small ends down. For each cup of yolks to be frozen,

add 1 tsp. sugar for use in sweet, or 1 tsp. salt for non-sweet dishes.

May also store unripe or hard apples at 60-70° F (16-21° C).

arton. Check

Bananas

Pears, plums, avocados Berries, cherries, apricot Grapes Citrus fruits

Pineapples, cut

VEGETABLES

Asparagus

Brussels sprouts, broccoli, cauliflower, green peas, lima beans, onions, peppers

Cabbage, celery

Carrots, parsnips, beets, and turnips

Lettuce

2-4 days

3-4 days 2-3 days 3-5 days

1-2 weeks

2-3 days

1-2 days

3-5 days

1-2 weeks

7-10 days

6 months (whole/peeled)

Not recommended

6 months

1 month (whole)

Not recommended

6-12 months

8-10 months

10-12 months

8-10 months

Not recommended

Ripen at room temperature before refrigerating. Bananas and

ados darken when refrigerated.

avoc

0° F (16

May also store at 6

. If refrigerated, store uncovered.

Will not ripen after purchase. Use quickly.

Don’t wash before refrigerating. Store in crisper.

Wrap odorous foods. Leave peas in pods.

rap odorous foods and refrigerate

W in crisper

Remove tops. Wrap odorous foods and refrigerate in the crisper

0-7

-21

Food Storage Tips

FOODS POULTRY AND FISH

Chicken and Turkey, whole

hicken and Turkey, pieces

ish

MEATS

Bacon Beef or lamb, ground

Beef or lamb, roast and steak Ham, fully cooked, whole

half slices

Luncheon meat

Pork, roast Pork, chops Sausage, ground Sausage, smoked Veal Frankfurters

REFRIGERATOR

1-2 days

-2 days

7 days

1-2 days

3-5 days

7 days 5 days 3 days

3-5 days

3-5 days 3-5 days 1-2 days

7 days

3-5 days

7 days

FREEZER

12 months

months

-6 months

1 month

3-4 months

6-9 months 1-2 months 1-2 months 1-2 months 1-2 months

4-6 months

4 months 1-2 months 1-2 months 4-6 months

1 month

STORAGE TIPS

Keep in original packaging for refrigeration. Place in the Meat and Cheese Drawer. When freezing longer than 2 weeks, overwrap with freezer wrap.

Fresh meats can be kept in original packaging for refrigeration.

Place in the Meat and Cheese Drawer. When freezing longer than 2 weeks, overwrap with freezer wrap.

Unopened, vacuum-packed luncheon meat may be kept up to 2 weeks in the Meat and Cheese Drawer.

Processed meats should be tightly wrapped and stored in the Meat and Cheese Drawer.

Sources: United States Department of Agriculture; Food Marketing Institute;

Cooperative Extension Service, Iowa State University

Storing the Refrigerator

Vacations*

If you will be gone for a month or less, leave the controls at the usual settings.

During longer absences:

1. Remove all food.

2. Shut off the ice maker (if installed) and the valve where you tapped into the water line to supply the refrigerator.

3. Disconnect the refrigerator from the electrical outlet.

4. Bleed the water from the ice maker fill line and dry the ice maker thoroughly.

* If using an automatic ice maker, discard first two or three ice harvests, when refrigerator is put back into service.

5. Clean and dry the refrigerator thoroughly.

6. Leave the doors open to prevent odors.

WARNING

Water damage due to improper disconnection and drainage may cause mold/mildew growth.

Moving*

When moving, follow instructions listed in Vacations. In addition, remove and carefully pack any items that are easily removable. Ship the refrigerator in an upright position with the doors taped shut.

Care & Cleaning

Refer to the char refrigerator cleaning guidelines.

t on the following page for specific

WARNING

To avoid electrical shock which can cause severe personal injury or death:

• Disconnect the power cord before moving or

cleaning the refrigerator.

• Disconnect the power cord before replacing the light

bulb.

CAUTION

To avoid personal injury:

Wear gloves when changing a light bulb to protect

•

against possible broken glass.

To prevent an accidental spill, drain any defrost water

3. which may have accumulated in the defrost drain pan. This pan is located behind the front base grille. To remove the pan, push down on both sides and slide it out.

4. If your model has been connected to a water supply for an automatic ice maker, turn off the water before moving the refrigerator.

5. Pull the refrigerator out from the wall.

Replacing a Light Bulb

0 watt appliance bulb.

ays use a standar

Alw Fresh Food Compartment

The light bulb is located under the top of the fresh food compartment.

d 4

No Clean™ Condenser

A clean condenser means more efficient refrigerator operation. Thanks to the unique design of the No Clean™ Condenser condenser cleaning in normal home usage surroundings.

Some operating environments may be particularly dusty or greasy. In these situations, the condenser can be periodic

, there is no longer a need for routine

ally cleaned to insure maximum efficienc

Cleaning Under the Refrigerator

Disconnect the power cord.

2. Raise the locking feet, if engaged (see page 3).

• Remove light shield, if present.

• Unscrew the light bulb and replace.

eezer Compartment

The freezer light (select models) is located on the back wall, near the upper right corner.

To remove the bulb cover:

• Grasp the top and bottom of the bulb cover. Press in the areas of the att unhook the t and remove.

• Unscrew the lightbulb and replace.

• Replace the bulb cover by pivoting it back into place and snapping the tabs into the appropriate slots.

achment t

abs. At the same time, pivot the cover down

abs, applying enough pressure to

Care & Cleaning

WARNING

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before cleaning. After cleaning, connect power.

Refrigerator Cleaning Chart

PART REFRIGERATOR

EXTERIOR Front base grille

Condenser

Door handles

Painted metal surfaces: Cabinet, doors

Defrost Drain Pan

Stainless steel doors (select models)

Stainless look exterior finish

Mild detergent and warm water. Mild liquid sprays. Vacuum cleaner attachment.

Cleaning brush (Part No.

20001017) available from your dealer.

Mild detergent and warm water. Mild liquid sprays.

Mild detergent and warm water.

Light cleaning: mild detergent and warm water.

Moderate soil: Bon Ami*. Discolorations: Cameo

Stainless Steel Cleaner*.

ash with a clean, soft cloth or

W sponge and a mild detergent in warm water.

CAUTION

To avoid personal injury or property damage, observe the following:

• Do not touch refrigerated surfaces with wet or damp hands, they may stick to the cold metal surfaces.

• Before cleaning the freezer, allow it to warm up.

• Allow glass shelves to warm up before immersing in warm water.

TIPS AND PRECAUTIONS

Remove the front base grille (see page 3).

No need for cleaning unless environment is particularly greasy, dusty or there is significant pet traffic in the home (see page 14).

Dry with a clean, soft cloth. Do not wipe the refrigerator with a soiled dishwashing cloth or wet towel. These may leave residue that can scratch and weaken the paint. Do not use scouring pads, powdered cleansers, bleach or cleaners containing bleach. These products can scratch and erode the paint finish. Do not wax plastic or vinyl parts.

Routine cleaning usually not necessary unless environment is particularly humid or dusty. Pan should be drained and cleaned prior to moving the refrigerator (see page 14).

Use a soft cloth or sponge. Always wipe with the grain of the stainless steel. Do not use chlorine bleach or a cleaning product that contains chlorine bleach. After cleaning, rinse and dry. To retore luster and remove

t No.

ss Steel Magic Spray* (P

streaks follow with St 2000000

Do not use abrasive or harsh cleaners, or cleaners designed for Stainless Steel. Dry thoroughly with a soft cloth.

8).

ainle

RIGERATOR AND

R I

F Door gasket

Glass shelves

Interior and door liner

awers, bins,

es, etc.

shelv

* Brand name

IOR

NTE

Baking soda and warm water. Mild detergent and warm water

Mild detergent and warm water. Glass cleaner Mild liquid sprays.

Mild detergent and warm water. Baking soda and warm water

Mild detergent and warm water

s are the trademarks of the re

spective manufacturer

Use 1-2 tablespoons baking soda per quart of water. Be sure to wring out exce when cleaning around controls, lights, or electrical par

Allow the glass to warm up to room temperature

e immersing in warm water. Never use hot

bef

ater

See above for baking soda solution. Do not use abrasive cleaners, concentrated detergent bleache clean the refrigerator interior.

Dry thoroughly Do not wash in automatic dishwasher

s, cleaning waxe

ss water from sponge or cloth

s, solvent

s or polish cleaners to

Troubleshooting

DEFROST TIMER: Frost-free refrigerators have a defrost timer that will generate a clicking sound when it cycles the unit into and out of defrost cycle.

ICE MAKER: (if equipped) The ice maker will occasionally generate a rattling sound when the ice cubes are ready to drop down into the ice bin. Also, the motor that ejects the ice from its tray prior to dropping the ice may also be detectable. These are normal sounds necessary for making ice.

FREEZER COMPARTMENT CONTRACTION AND EXPAN- SION: A popping sound may

occur in the freezer when the unit starts up due to contraction or expansion of the materials in the freezer area.

DEFROST HEATER: During the automatic defrost cycle, a sizzling sound may be heard as water droplets come into contact with the defrost heater. This is a normal sound heard during defrost.

REFRIGERANT FLOW: The flow of the refrigerant in your refrigerator may cause a gurgling or rattling sound when the unit is running or just after the unit cycles off. The refrigerant is still flowing in the tubing.

AIRFLOW SOUNDS: Both the freezer evaporator fan and the condenser fan at the bottom of the cabinet will create airflow sounds. The evaporator fan is circulating the cold air throughout the refrigerator and freezer compartments. The condenser fan is removing the heat generated when the unit is cooled.

WATER VALVE (if equipped): A buzzing sound may be detected in the back of the unit when the ice dispenser calls for the water valve to open to fill the ice maker tray. Following the ejection of the ice, there may be some water dripping sounds when the trays are being filled.

CABINET LEVELING: An unlevel cabinet may cause rattling or vibrating noises. This can be fixed by adjusting the wheels or levelers properly.

COMPRESSOR: In order for a new refrigerator to run more efficiently, the refrigeration system may run longer to keep food at the desired temperatures for freshness. That new, high efficiency compressor may run longer and generate sounds such as a higher pitched hum or pulsation.

Normal Operating Sounds

Improvements in refrigeration design may produce sounds in your new refrigerator that are different or were not present in an older model. These improvements were made to create a refrigerator that is better at preserving food, is more energy efficient, and is quieter overall. Because new units run quieter, sounds may be detected that were present in older units, but were masked by higher sound levels. Many of these sounds are normal. Please note that the surfaces adjacent to a refrigerator, such as hard walls, floors and cabinetry may make these sounds seem even louder. The following are some of the normal sounds that may be noticed in a new refrigerator.

Troubleshooting

Review this chart of troubleshooting tips first…you may not need to call for service at all.

PROBLEM

Won’t run

Runs too long, too frequently

Light not working

GENERAL OPERATION

Visible glow in freezer vents

Warm air from cabinet bottom

Cabinet vibrates Odor in cabinet Noise, sounds

eezer, r

ations

efriger

and vibr

NOISETEMPERATURE

F too warm

POSSIBLE CAUSES

Power cord not plugged in.

No power to outlet. Fresh food control set to “OFF” position.

Refrigerator is in automatic defrost.

Room temperature less than 55° F (13° C).

Today’s refrigerators start and stop more often to maintain even temperatures.

Normal at startup for new or recently installed units.

rolonged or frequent door openings.

Door not sealing.

Front base grille blocked.

Bulb burned out.

No power to unit.

Appearance of a red glow or reflection is normal during the defrost cycle.

This is normal air flow for condenser circulation.

Cabinet not level. Weak floor.

Odor producing foods not covered.

Normal noise.

Cabinet not level.

ator

Control set too warm. Prolonged door openings.

Room temperature less than 55° F (13° C).

WHAT TO DO

Push plug into outlet.

Replace fuse, reset circuit breaker.

Set fresh food control (see page 7).

Wait 25 minutes for defrost cycle to end.

Relocate unit to proper climate (see Installation on page 3).

Wait 24 hours for refrigerator to completely cool down

Temperature Controls on page 7).

(see

This is normal. Minimize door openings.

Check to see if something is preventing door from closing.

Unblock to allow warm air to exit unit.

Unplug refrigerator and change bulb (see page 14).

Check to see if power cord is completely plugged in properly.

Level cabinet (see page 3).

Cover or wrap odorous foods tightly. Clean cabinet.

Normal Operating Sounds (page 16).

See

abinet (see page 3).

evel c

Adjust temperature control (see page 7). Minimize door openings.

Unit will not run often enough to maintain proper temperature

eezer, r

F too cold

efrigerator

Products with high sugar content may not harden completely when frozen.

Control set too cold.

Adjust temperature control (see page 7).

Troubleshooting

PROBLEM

utomatic icemaker

A not working

Ice cubes have odor/taste

ICEMOISTURE

Ice cubes sticking in tray

Ice cubes evaporating

Moisture on cabinet surface between doors

Moisture on inside cabinet walls or in crisper

POSSIBLE CAUSES

ensor arm in up position.

abinet not level.

Water supply not connected or restricted.

Freezer too warm.

Old cubes.

Bad water quality.

Food transmitted odor/taste to ice.

Residue from minerals in the water.

Limited use of ice.

Not unusual during periods of high humidity.

Hot humid weather.

Frequent or prolonged door openings.

Door not closed properly.

WHAT TO DO

djust sensor arm down to “ON” position.

evel unit (see page 3).

Connect water supply, or clear obstructions.

Adjust freezer temperature control (see page 7).

Discard; ice cubes may absorb odors which affect taste.

Contact local water treatment company.

Wrap foods tightly.

Wipe trays with vinegar-soaked cloth until clean.

Dump old ice cubes.

Normal.

Minimize door openings.

Check to see if something is preventing door from closing.

Foods dry out

Excessive moisture in crisper

Food not wrapped properly.

Crisper not tightly closed.

Temperature controls set too cold.

Packages not wrapped or sealed properly.

Hot, humid weather.

Humidity slide on crisper needs adjustment.

Too much moisture on fresh produce before storing.

Foods not stored properly.

Wrap or cover all foods tightly.

Close crisper all the way.

Adjust temperature controls (see page 7).

Wrap or cover all foods tightly.

Minimize door openings.

Slide control to “Fruit” setting to allow more moisture to leave the drawer.

Do not wash items prior to storage. Wait to wash fresh items until right before use.

Store leafy vegetables in a loosely closed plastic bag. Store items with an outer skin (i.e. apple pears, grapes, cucumbers, etc.) in a vented bag or unwrapped in the drawer. Store mushrooms and berries in original vented cartons or boxes, not in plastic bags.

s, orange

Warranty & Service

Warranty

Limited One Year Warranty Parts and Labor

For one (1) year from the original retail purchase date, any part which fails in normal home use will be repaired or replaced free of charge.

Canadian Residents

The above warranties only cover an appliance installed in Canada that has been certified or listed by appropriate test agencies for a compliance to a National Standard of Canada unless the appliance was brought into Canada due to transfer of residence from the United States to Canada.

The specific warranties expressed above are the ONLY warranties provided by the manufacturer. These warranties give you specific legal rights, and you may also have other rights which vary from state to state.

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. MAYTAG CORPORATION SHALL NOT BE LIABLE

ENTAL OR CONSEQUENTIAL

R I

F DAMAGES. SOME STATES AND

OVINCES DO NOT ALLOW THE

ION OR LIMITATION OF

L OR CONSEQUENTIAL

I DAMAGES, OR LIMITATIONS ON THE

ATION OF IMPLIED WARRANTIES OF

ABILITY OR FITNESS, SO

M THESE EXCLUSIONS OR LIMITATIONS

AY NOT APPLY TO YOU. THIS

ANTY GIVES YOU SPECIFIC LEGAL

W RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY STATE TO

R PROVINCE TO PROVINCE.

TE O

What is Not Covered By These Warranties

1. Conditions and damages resulting from any of the following: a. Improper installation, delivery, or maintenance. b. Any repair, modification, alteration, or adjustment not authorized by the

anufacturer or an authorized servicer.

. Misuse, abuse, accidents, unreasonable use, or acts of God.

c d. Incorrect electric current, voltage, electrical and/or gas supply. e. Improper setting of any control.

2. Warranties are void if the original serial numbers have been removed, altered, or cannot be readily determined.

3. Light bulbs, water filters and air filters.

4. Products purchased for commercial or industrial use.

5. The cost of service or service call to: a. Correct installation errors. For products requiring ventilation, rigid metal

ducting must be used. b. Instruct the user on the proper use of the product. c. Transport the appliance to and from the servicer.

6. Any food loss due to refrigerator or freezer product failures.

7. Expenses for travel and transportation for product service in remote locations.

8. Outside of the United States and Canada this warranty does not apply. Contact your dealer to determine if another warranty applies.

9. Consequential or incidental damages sustained by any person as a result of any breach of these warranties. Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusion may not apply.

If You Need Service

First see the Troubleshooting section in your Use and Care Guide or call the dealer from whom your appliance was purchased or call Maytag Services, LLC, Customer Assistance at 1-800-688-9900 USA and 1-800-688-2002 Canada to locate an authorized servicer.

• Be sure to retain proof of purchase to verify warranty status. Refer to WARRANTY ther information on owner’s responsibilities for warranty service.

for fur

• If the dealer or service company cannot resolve the problem, write to Maytag

Services, LLC, Attn: CAIR 1-800-688-9900 USA and 1-800-688-2002 Canada. U.S. customers using

Y for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

• User’s guides, service manuals and parts information are available from Maytag

Services, LLC, Customer Assistance.

Center, P.O. Box 2370, Cleveland, TN 37320-2370, or call

Notes: When writing or calling about a service problem, please include:

a. Your name, address and telephone number; b. Model number and serial number; c. Name and address of your dealer or servicer; d. A clear description of the problem you are having; e. Proof of purchase (sales receipt).

+ 44 hidden pages

Daewoo MAYTAG User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual