Daewoo LSE-09 Service Manual

Download

S/M No. :

LSE0900001

Service Manual

Drum Washing Machine

Model: LSE09

✔ Caution

: In this Manual, some parts can be changed for improving, their

performance without notice in the parts list. So, if you need the

latest parts information, please refer to PPL(Parts Price List) in

Service Information Center (http://svc.dwe.co.kr).

Nov. 2010

DRUM WASHING MACHINE

SERVICE MANUAL

1. WHAT IS DRUM WASHING MACHINE? ......................................1

2. WASHER SPECIFICATION ..........................................................3

3. PARTS LIST BY ASS'Y .................................................................4

4. CONTROL PART FUNCTION SPECIFICATION ........................17

5. ELECTRONIC FIELD PARTS LIST AND SPECIFICATION .......26

6. WIRING DIAGRAM .....................................................................27

1. WHAT IS DRUM WASHING MACHINE?

1. Drum Washing Machine

Water consumption is reduced by using the power of the laundry falling (free-fall) created when rotating

the drum. With temperature control system, this drum washing machine saves energy and improves

washing performance at the same time.

2. Key Features

◈ Waist Care Designed by the waist, and the most comfortable

angle eject into the laundry is convenient and easy to manipulate.

◈ Star Drum Using Star Drum is able to show users higher

Washing Performance and Minimal damage of laundry, water consumption.

◈ Luxury Audio Dial Using the advanced Audio Dial is luxury design of

exterior.

◈ DD inverter motor The direct-drive type of which motor is directly

connected to drum without an interim clutch, significantly reduces noise and vibration.

◈ Self-Cleaning Course of Drum. Enables the machine to do Self-Cleaning of Drum.

◈ Digital Condensing Dry System. Condensing Dry System with saveing energy.

3. Power System

LAUNDRY

Pump Drainage

• DD Control: Direct drive type of direct connection between drum and motor

• Rotation by powerful high-performance BLDC motor

BLDC

2. WASHER SPECIFICATION

1. Product Specification

MODEL NO. LSE09

Power Source AC220V / 60Hz AC127V / 60Hz

Power Consumption 2100W, 9.5A 1350W, 10.6A

Dimension (WxHxD,mm) 600 x 645 x 850 mm

Maximum mass of textile(Kg) 9Kg

Unit Weight (net/gross) 76 Kg / 80Kg

Standard Water Consumption 65 ℓ

Operating Water Pressure 0.3kgf/cm² ~ 8kgf/cm² (0.03MPa ~ 0.8MPa)

3. PARTS LIST BY ASS'Y

1. PANEL AS

F29

F05

F06

F07

F04

F03

F02

F01

F10 F11 F12

F08 F09

F15

F28

F16

F30

F13

F17

F18

F14

F20

F19

F21

F23

F22

F27

F25

F24

F26

F31

No. PARTS NAME CODE SPECIFICATIONS Q’TY REMARK

F01 CASE DETERGENT AS 36111T1P20 LSE09 1

F02 CAP SOFTENER 3610916600 PP 1

F03 CASE DETERGENT 36111T1J00 PP 1

F04 PANEL*F 36142T3800 ABS WH-011A 1

F05 SCREW TAPPING 7122401608 T2S TRS 4*16 SUS430 2

F06 CASE HANDLE 36111T2S00 ABS WH-011A(SILK) 1

F07 HANDLE CAP 3612613700 ABS(SPRAY) 1

F08 DECORATOR WINDOW 36116DGM00 ABS(PLATE)GY-349A 1

F09 WINDOW DISPLAY 3615511400

0 BUTTON FUNCTION 3616647100 ABS(SPRAY)GY-349A 1

F11 DECORATOR FUNCTION 36116DGN00 ABS 1

F12 BUTTON DOOR LOCK 3616647000 ABS WH-011A 1

TR-ABS(TRANSPARENCY)BK-5503AT(LG)

F13 DECORATOR POWER 36116DGP00 ABS 1

F14 POWER AS - ABS 1

F15 DECORATOR FILM RD-2Y201J- 1/2 200 OHM J 1

F16 CUSTOM LED 3613058320 ABS 1

F17 POWER SW TACT 5S50101401 2PIN 8*8*13 1

F18 HOLDER POWER 3613048800 ABS 1

F19 BUTTON DIAL IN 3616646800 ABS WH-011A 1

F20 GASKET BUTTON 3612321500 SPONGE,OD=29,T5,HOLE=9 1

F21 BUTTO

F22 BUTTO

F23 HOLDER COURSE OUT 3613064000 ABS(SPRAY) 1

F24 HOLDER COURSE IN 3613063900 TR-ABS(TRANSPARENCY) 1

F25 HOLDER COURSE NAIN 3613063800 HIPS 1

F26 PCB AS PRPSSWL076 C-LD1442 1

F27 SCREW TAPPING 7122401211 T2S TRS 4*12 MFZN 7

F28 CASE PCB FRONT 36111T2R00 HIPS 1

F29 PANEL FRONT AS PRPAFR LDAO LD1442EC 1

F30 SW TACT 5S50101402 2PIN, 6*6*5 9

F31 P

N DIAL MIDDLE 3616646900 ABS(GLOSSY DISPOSTION) 1

N DIAL OUT 3616646700 TR-ABS(TRANSPARENCY) 1

ANEL *F OUTER AS 36142T3810 LSE09 PANEL *FRONT AS 1

2. INLET BOX AS

B15

B10

B12

B02

B14

B06

B13

B09

B07

B01

B08

B11

B04

B05-1

B05

B03

No. PARTS NAME CODE SPECIFICATIONS Q’TY

B01 NOZZLE *T 3618111100 PP 1

B02 NOZZLE *U 3618111000 PP 1

B03 BOX INLET 3610526500 PP 1

B04 HOSE INLET 3613274600 EPDM 1

B05 CLAMP AS 3611203200 ID=60, WIRE+GUIDE+BOLT+NUT 1

B05-1 SPECIAL BOLT 3616030100 M4x50, DWD-100DR, CLAMP AS 1

VALVE INLET 3615415050 220~240V,3WAY,RINSE GUIDE,PP/BRACKET 1 Elux

B06

VALVE INLET 3615415070 100~130V,3WAY,RINSE GUIDE,PP/BRACKET 1 Elux

B07 HOSE WATER SUPPLY 3613270900 EPDM ID9.5 OD14.5, WASHING 1

B08 HOSE WATER SUPPLY 3613270900 EPDM ID9.5 OD14.5, PRE.WASH 2

B09 CLAMP HOSE 3611205800 100H, ID=13.8 W=10.0 0.9T 10

VALVE INLET 3615414800 220-240V 1-WAY HOT PP-BRACKET 1 Elux

B10

VALVE INLET 3615415700 100-130 1-WAY HOT PP-BRACKET 1 Elux

B11 HOSE WATER SUPPLY 3613270900 EPDM ID9.5 OD14.5, HOT 1

B12 HOSE WATER SUPPLY 3613270900 EPDM ID9.5 OD14.5, STEAM 1

PIPE JOINT I 3614426000 PP 1

B13

PIPE JOINT(HOSE INLET)

3614413300 PP , T-type 1

REMARK

PIPE JOINT

B14 Unit Steam AS 36189M2U00 L-SERIES STEAM UNIT 900W 1 option

B15 INLET BOX AS 3617511103 C-L GEN HOT NST 1

3614413100 ABS 1 Elux

3. CABINET F ASSY

C04

C01

C03

C18

C11

C19

C02

C05

C06

C07

C13

C12

C10

C09

C14

C15

C16

C17

C06

No. PARTS NAME CODE SPECIFICATIONS Q’TY REMARK

C01 CABINET FRONT AS

C02 CABINET FRONT SUB AS 3610814010

C03 SWITCH DOOR LOCK

C04 PLATE HINGE SUPPORT 3614539800 SPG 0.8T, DWD-T110R 1

C05 FRAME DOOR *O 36122UD800 ABS 1

C06 PROTECTOR GLASS 3618345500 ABS 1

C07 DECORATOR DOOR *O 3611695900 ABS 1

C08 HOOK DOOR 3613100900 ZNDC 1

C09 SPRING HOOK 3615115400 SUS304, 1

C10 HOOK SHAFT 3613101000 SUS, D=3.0 1

C11 FRAME DOOR *I 36122UD600 PP 1

C12 HINGE DOOR 3612903800 AL, DWD-T110R 1

C13 CAP HINGE DOOR 3610916500 POM 4

C14 DOOR GLASS 361A113300 GLASS 1

C15 CASE PUMP AS 36111T1K10 CASE PUMP(PP)+PAD 1

C16 CASE PUMP 36111T1K00 PP 1

PRCAFRDL24 LSE09(127V/60Hz) 1

PRCAFRDL00 LSE09(220V/60Hz) 1

C/D-L/S CKD CABINET PAINTING WH

3619047230

3619047210

DL-S2,250V,16A,BITRON,VE-TYPE

DL-S1,124V,16A,BITRON

C17 COVER PUMP 3611431500 ABS 1

C18 DOOR AS 36117ACE01 D-LU1012 1

C19 SCREW TAPPING 7115402029 T1S FLT 4x20 STS430 NATURAL 17

4. TUB ASSY(DD MOTOR)

D09

D07

D04

D10

D05

D08

D06

D48

D21

D11-2

D11-1

D22-1

D11-4

D22-3

D11-3

D22-5

D19

D18

D17

D11-5

D22

D22-4

D47

D20

D46

D11

D11-6

D45

D44

D01

D02

D28

D03

D36

D34

D35

D30

D37

D27

D29

D38

D40

D39

D41

D33

D31

D42

D32

D44-1

D49

D43

D43-1

No. PARTS NAME CODE SPECIFICATIONS Q’TY REMARK

D01 BALANCER WEIGHT L 3616110600 PP, D-LU1011, 6.6KG 1 D02 SPECIAL SCREW 3616029400 SWCH 8.5X30 8 D03 BALANCER WEIGHT R 3616110500 PP, D-LU1011, 6.6KG 1 D04 CLAMP GASKET AS 3611207000 C-LU1011 1 D05 GASKET 3612325300 EPDM , WASH , D-LU1011 1 D06 GASKET 3612325400 EPDM , DRY , C-LU1011 1 FOR DRY D07 NOZZLE SHOWER 3618111200 PP 1 D08 CLAMP GASKET BUSHING 3611206800 D09 SPECIAL SCREW 3616029810 SWCH 6.5X45 4 D10 DUCT B AS 3610DUTL00 C-L E 1 FOR DRY D11 HOSE DRAIN AS 3613268810 LD HOSE DRAIN + AIR TRAP + CLAMP 1

D11-1 HOSE DRAIN *I 3613275200 EPDM D-LU1011 1 D11-2 CLAMP AS 3611203210 ID=61, WIRE+GUIDE+BOLT, GS 1 D11-3 CLAMP HOSE 3611204700 D26 1 D11-4 CLAMP HOSE 3611201401 HSW3,YW,D2.6,ID36,W44.5 1 D11-5 AIR TRAP 361A500101 PP 1 D11-6 HOSE AIR(PRESSURE) 3613266930 ID=4,OD=8, L=680MM(L-SERIES) 1

D17 DAMPER FRICTION 361A700110 D18 DAMPER PIN 361A700200 AKS D=14.5 2 D19 TUB FRONT 3618830000 FRPP, C-LU1011 1 D20 SPRING SUSPENSION 3615116800 KGF 2 D21 SPECIAL SCREW 3616029800 SWCH 6.5X30 14 D22 DRUM AS 3617012500 D-LU1011 1

D22-1 SPECIAL SCREW 3616029500 SUS430 8*25 3 D22-2 LIFTER WASH 361A401300 PP,1PIECE,TWIST 3 D22-3 SCREW TAPPING 7122401408 T2S TRS 4X14 SUS,STS 3 D22-4 DRUM SUB AS 3617012600 D-LU1011 1 D22-5 SPIDER AS 361A301200

D27 WATER SEAL 361A600100 NBR 1 D28 SEALING TUB 3612321601 EPDM L1600(-0~ +10) 1 D29 FIXTURE HEATER 3612006700 SUS 1 D30 BEARING INNER 3616303100 6206Z 1 D31 DAMPER FRICTION 361A700130 D32 DAMPER PIN 361A700200 AKS D=14.5 2 D33 TUB REAR AS 36100T1400 D-LU1011 1

D33-1 TUB REAR 3618830100 FRPP, C-LU1011 1 D33-2 BEARING HOUSING 3616305000 ALDC, D-LU1011 1

D34 BALANCER WEIGHT T 3616110400 PP, C-LU1011, 2.48KG 1 FOR DRY D35 BALANCER WEIGHT T(WASH) 3616110700 PP, D-LU1011, 2.48KG 1 D36 SPECIAL SCREW 3616029400 SWCH 8.5X30 2 D37 CLAMP HOSE 3611204700 D26 1 D38 SPECIAL SCREW 3616007400 T2S TRS 4X10+24 2 OPTION D39 UNIT BUBBLE GENERATOR 36189L4177 D40 HOSE VENT 3613267100 EPDM 1 D41 BEARING OUTER 3616303200 6205Z 1

HEATER WASH 3612802400 220V 2KW.1R0A721001.RW8TF.IRCA,NPB 1 ELECTROLUX

D42

HEATER WASH 3612802420 240V 2KW.1R0A721003.RW8TF.IRCA 1 HEATER WASH 3612802440 120V 1KW.1R0A721005.RW8TF1PE.IRCA 1 ELECTROLUX HEATER WASH 3612803700 230V 2000W.1R5A721002.IRCA FUSE 2EA 1

D43 PIPE DUCT AS 3614414001 C-L PIPE DUCT+HOSE+CLAMP 1

D43-1 PIPE DUCT 3614414000 PP 1

D44 UNIT STATOR BLDC 36189L620A AL,DON1300W 30T 36POLE,NMT,PBT 1 20091211~

D44-1

HALL IC HOLDER AS 3616D01000 D45 SPECIAL BOLT AS 3616063400 SWCH M8x58mm 6 D46 UNIT ROTOR BLDC 36189L6300 DON1300W SR-FERRITE12,30~32T,NMT 1 20091211~ D47 SPECIAL BOLT AS 3616029620 SWCH 10*30 S/W P/W NON-SEAL LOCK 1 D48 CAP NOZZLE SHOWER 3610919400 EPDM, L-SERIES 1 D49 THERMISTOR WASH 361AAAAB10 R25=1.704KΩ, R80=11.981KΩ 1

GI 1.2T

70N AKS ST=170-260 DL=197.5 LOW NOISE

D-LU1011

60N AKS ST=170-260 DL=197.5 LOW NOISE

HIGH,PAD B,BL/WH,320,RP4,GUIDE O,SPONGE 200

DRUM STATOR PCB HOLDER AS(SVC),NMT

FOR WASH

1 FOR DRY

FOR WASH

1 OPTION

5. DUCT B (for dry model)

E12

E01

E01-1

E09

E02

E04

E07

E03

E11

E05

E11-5

E11-4

E11-3

E11-2

E11-1

E06

E08

E10

No. PARTS NAME CODE SPECIFICATIONS Q’TY REMARK

E01 DUCT B UPPER AS 361A202400 C-L DUCT B UPPER + GASKET SEAL 1

E01-1 DUCT B UPPER 361A202400 ALCOSTA 1

E02 SCREW TAPPING 7122401411 T2S TRS 4X14 MFZN 8

E03 SCREW TAPPING 7112401208 T1 TRS 4X12 SUS 1

E04

HEATER DRY

E05 PACKING THERMOSTAT 3614009900 SILICON, DWD-100DR 1

E05 SWITCH THERMOSTAT 3619046500 ON120°C OFF150°C 230V 15A VDE 1

E06 DUCT B LOWER 361A202500 ALDC C-LU1011 1

E07 BUSHING UPPER 3610703800 POM C-LU1011 4

E08 BUSHING LOWER 3610703900 POM C-LU1011 4

E09 GASKET SEAL A 3612325700 EPDM FOAM, D=5, L=1293 1

E10 PACKING RUBBER 3614009800 SILICON, DWD-100DR 1

E10 THERMISTOR DRY 361AAAAD00

E11 FAN MOTOR AS 36189M2Q30 C-LD,17.5V,VCD,C.W 1

E11-1 NUT HEX 3616032100 M6*1.0P,CCW 1

E11-2 FAN AS 3611886400 GFPP30% , C-LU1011 1

E11-3 COVER DUCT 3611431400 GFPP30% C-LU1011 1

E11-4 RING O 3614603410 DWD-100DR,NBR,ID=7.6,OD=13.6 1

E11-5 UNIT FAN MOTOR 36189M2Q00 24V DC 14W 1

E12 DUCT B AS 3610DUTL01 C-L'S 1

3612800920

3612802100

220V,2100W,23.05Ω,6.1W/SQ,INCOLOY800,IR1A034001

UL120V,12kW,1.20Ω,3.5W/SQ,INCOLOY800,RA8,IR1A34008

C-LD/LU,L=200,R40=26.065K,R90=4.4278K

6. CABINET AS

F11

F02

F13

F07

F03

F01

F14

F18

F12

F06

F19

F08

F06-1

F15

F20

F11-1

F17

F06-2

F11

F06-2-1

F06-2-2

F11-2

F09

F10

F11-5

F11-4

F11-3

F04

F05

F05-1

No. PARTS NAME CODE SPECIFICATIONS Q’TY REMARK

F01 CABINET 3610813300 SGCC 0.8T,L'S 1

F02 FRAME LOWER 36122UD700 SGCC 1.2T 1

F03 FRAME TOP *L 36122UDA00 SGCC 1.6T 1

FRAME TOP *R 36122UDB00

F04 BASE U L 3610393800 SGCC T2.0 1

BASE U R 3610393900 SGCC T2.0 1

F05 LEG ADJUST AS 3617703811 CHINA PARTS, DWD-900W 4

F05-1 SPECIAL NUT 361031100 SCP1, LEG 4

MAIN PCB AS 361MPCLD61 C-LD4 EC NF BEA CC H NBB NST 1

F06

MAIN PCB AS 361MPCLD62 C-LD4 127V EC NF REA CC H NBB NST 1

F06-1 HARNESS AS 3612799R50 LSE09,NF,H,NB,R,NS,C 1

PCB INVERTER AS PRPSSWL960

F06-2

PCB INVERTER AS PRPSSWL961

FUSE GLASS TUBE 5FVGB8022S

F06-2-1

F06-2-2

RELAY 5SC0101160

F07 PLATE TOP AS 3614541110 LD PAINTING WH 1

F08

SENSOR PRESSURE

F09 COVER *B AS 3611431610 LD COVER B+CUSHING 1

F10 COVER *B 3611431600 0.4T,SGCC,C-LU1011 1

F11 FIXTURE TUB AS 3612007400 DWD-800W 4

F12 FRAME UPPER 36122UD900 SGCC 1.2T 1

F13

UNIT DRAIN PUMP AS

F14 STOPPER SPRING 3615202200 POM, DWD-100DR 2

F15

CAP WATER REMAIN

F16 CORD POWER AS 3611339950 H05W-F 1.5SQ 25V 1.6A 1.6M EU-2PIN 6KG 1

F17 HANDLE REAR 3612612800 ABS 2

F18

HOSE WATER REMAIN

F19 NOZZLE AIR 3618111400 PP 1

F20

HOSE DRAIN OUTER AS

3614825240 DL-DW13 AIR INLET 315 1

36189M1500

36189M1800

3610916800 PP 2

3611339940 H05W-F 1.5SQ 25V 1.8A 1.6M EUR-IMPOART 1

3611342370

3613268701 0.4T, SGCC, C-LU1011 1

3613274900 L'SERIES 1

SGCC 1.6T

LD4'S,DRY,EC,NON-BB,220,HOT,CIC,NON-STM,ELUX

LD4'S,DRY,EC,NON-BB,110,HOT,CIC,NON-STM,ELUX

8A 250V TL

PLFN-112D2M 25A, DC12V

AC220V/60HZ HANYU,AL,30W,DUAL PUMP,CIRCUL NEW

AC120V/60HZ HANYU,CU,30W,DUAL PUMP,CIRCUL NEW

BRAZIL ANGLE DANEVA 3X 1.5SQ H05W-F11KG DRUM

1 Elux

7. ACCESSORIES

HOSE INLET AS MANUAL OWNERS

G01 G02 G03 G04 G05

No. PARTS NAME CODE SPECIFICATIONS Q’TY REMARK

G01 HOSE INLET AS

G02

MANUAL OWENERS

G03 CAP HOLDER 3610916400 PP, DWD-100DR 4

G04

GUIDE HOSE DRAIN

G05

UNIT SVC WRENCH

BOX PACKING 3610528400 650*730*880, PAPER 1

BOX BOTTOM 3610528500 PAPER 1

3613216105 SCREW, COLD, NEW IM, G/S 1

3613216115 SCREW, HOT, NEW IM, G/S 1

3613725740 L'S 1

3612502300 PP,JI-360 1

36189L3X10 EGI, 2.3T, DWD-100DR

CAP HOLDER

(4EA)

GUIDE HOSE

DRAIN

(OPTION)

UNIT SVC

WRENCH

(OPTION)

4. CONTROL PART FUNCTION SPECIFICATION

1. SEQUENCE CHART

Division Time

Sensing 20sec

Water Supply 2min

R E. W

END

Pre. Wash

I N G

I N S E

S P

I N

Drain 1min

Balancing Spin 2min

Mid.spin 3min

Sensing 20sec

Water Supply 2min

Washing 1

(Heating)

Washing 2

Drain 1min

Balancing Spin 2min

Mid.spin 4min

Water Supply 2min

Rinse 1 3min

Drain 1min

Balancing Spin 2min

Mid.spin 4min

Water Supply 2min

Rinse 2 3min

Drain 1min

Balancing Spin 2min

Mid.spin 4min

Water Supply 2min

Rinse 3 3min

Drain 1min

Balancing Spin 2min

Main Spin

Crease care 60sec

End 10sec

Remain Time Display 1:07 1:12 1:14 1:40 2:41 2:56 2:01 2:21

NOTE

Jeans

Small Middle Small Middle Small Middle Small Middle

10min

8min

▒ ▒

▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒

100min 28min 33min 23min 33min 25min 30min 25min 30min

50min

20min

15min

▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒

9min

5min

3min

▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒

1. In the Cotton/Normal Course, if select 95°C ,real temperature is 85°C and Heat OFF.

2. As cannot reach the temp. end of the heating.

Bedding

Remove

Stain

▒

▒ ▒ ▒ ▒ ▒ ▒

Dingy White Bed & Bath

▒

85min▒95min▒45min▒60min

▒ ▒

▒

1717

Division Time

A S H

I N G

I N S E

S P

I N

D R Y

END

Soal 30min

Water Supply 2min

Washing 2

Drain 1min

Balancing Spin 2min

Mid.spin 4min

Water Supply 2min

Rinse 1 3min

Drain 1min

Balancing Spin 2min

Mid.spin 4min

Water Supply 2min

Rinse 2 3min

Drain 1min

Balancing Spin 2min

Mid.spin 4min

Water Supply 2min

Rinse 3 3min

Drain 1min

Balancing Spin 2min

Main Spin

Crease care 60sec 46min

Dry

Cooling 5min

End 10sec

Crease care 30min

Crease care 60sec

End 10sec

Remain Time Display 52 55 1:32 46 2:03 1:07

Easy

Ironing

Small Small Small Small Middle

100min

50min 18min

20min

15min 7min

7min

9min

5min

3min

40min

15min

Synthetic/

Delicate

▒ ▒ ▒ ▒ ▒

15min

▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒

▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒

▒ ▒ ▒ ▒ ▒

Normal Quick Self Clean

53min

▒ ▒ ▒

▒

10min

▒ ▒ ▒

Favorite

Programs

28min

1818

2. Skill of Spin and Dry Sequences

2-1. Spin Sequence

1) Drain

①

It follows Drainage Sequence.

2) Balance Spin

①

If Unbalance Check pass, Start R-Spin.

②

B-Spin is Until Unbalance check section, 350 r.p.m

3) R(Real) Spin

①

From end of B-Spin to end of Spin Sequence is R Spin.

②

r.p.m is affected by sequence

4) Shoes Spin

①

Balace Spin does not work.

2-2. End

1) Crease Care

①

Crease Care is process of removal laundry that stick to drum. It works 30sec ,after Spin Sequence.

②

Wool and Shoes course don't work crease care

2) End

①

After 10 sec power off ,alamed END.

②

If drying sequence added, drying sequence works.

③

After END , door unlock.

2-3. Drying Sequence

1) Consist of drying sequence. ex) select normal drying (Total spend time 4:08)

Drain(1min)

Crease Care(30min)

➞

→ Not Displayed

2) Electric Current Time of Dry Sequence.

Remove smell 35 100/90 95/85

Delicate 1:30 70/60 70/60

Normal 3:30 100/90 95/85

Extra Dry 4:30 100/90 95/85

3) Drying V/V working

①

It works from the after 20sec, In Drying Sequence to End of Drying Sequence.

4) COOLING

①

Fan motor and Main motor work at once during Cooling Sequence.

②

Temp. of Drum is less than 60°C finish Cooling Sequence.

③

Cooling time is total 5 min.

➞ ➞ ➞

Time 1,2,3,4 hour(s) 100/90 95/85

Drying(209 min) COOLING(5min) End(10sec)

Time(min)

Heater Off/On, Temperture(°C)

220V 110V

5) Drying Heater working

①

Drying Heater: 90°C ON / 100°C OFF (High Voltage) , 85°C ON / 95°C OFF (Low Voltage)

②

Shoes Course : 60°C ON / 70°C OFF

③

Remove Smell : 90°C ON / 100°C OFF( High Voltage) , 85°C ON / 95°C OFF(Low Voltage)

6) Crease Care

①

Crease Care performs after Drying Sequence for 30 min.

②

Only Motor work during Wrinkle Free

2020

3. Main Function of PCB Program

3-1. LOAD SENSING

1) Deciding the water level

①

Normal, White, Eco-White Course will be followed by this process.

②

Check the water level with dry laundry at the starting wash.

③

Check the water level by using motor output data during 20 sec, 65rpm.

2) Deciding Spin Starting Step.

①

Check after finishing washing step with wet laundry.

②

Checking by using motor output data during 20 sec, 65 rpm.

③

The Decided data is different depending on loading condition.

3-2. Balance Spin

1) Motor runs during balance spin

①

Spreading the laundry : Rotating the same 45 rpm with left and right direction alternatively.

②

Unbalance checking point : first step, sheck the U.B at 95 rpm, 160 rpm second step, check the U.B

at 95 rpm 350 rpm.

Third step at 300 rpm. If the unbalance data is over the criterion

This process will be repeated.

③

After drain, check the unbalance data again. This is so-called balance spin step.

3) Property of balance spin

①

Conducting 20 times maximum.

②

If the washer can not pass balance spin step during 20 times, then water will be supplied.

③

If the washer can not pass 20 times of balance spin, UE error mode will be displayed on '18:88'

3-3. DOOR S/W

1) The working principle of Door S/W

①

Door Locking

Bimetal on (3 sec) → solenoid (supply 20msec pulse 2 times)

②

Door Unlocking

Bimetal off → solenoid(supply 20msec pulse, until lock)

③

After door locking all parts can work nomally.

④

After pressing power button, if the temperature of wash thermistor is over 61℃ or the water level is

over the safety level, the door will be locked.

⑤

The door will be unlocked immediately after all processes are finished.

⑥

The door can be opened during processing if there is no problem to unlock.

2) DOOR OPEN SYSTEM

①

If add the laundry during washing, press the door unlock button.

②

Door open sequence at abnormal condition.

3-4. Child Lock

①

Press the "Wash" and "Temp." button simultaneously during processing.

②

Under the Child Lock function, only power button is working.

③

During Child Lock function, CHL will be displayed on '18:88'

④

In order to unlock Child Lock mode, press "Wash" and "Temp." simultaneously.

3-5. The sequence of drain

①

If the checking time to reset point is below 1 min, the remaining drain time is 40 sec.

②

If the checking time to reset point is over 1 min, the remaining drain time is 2 min.

③

If the checking time to reset point is over 10 min, OE signal will be appeared on PCB.

④

If the temperature is over 50℃ , the water will be supplied to high water level, then the drain will

start.

4. TEST MODE

4-1. Testing Mode

PCB and other electronic parts will be tested without water supply whether they are normal or not.

1) Process

Press power button → Press "SPIN" button 3 times with pressing "WASH" button → 'L d' will be shown

on LED → Whenever pressing "TEMP" button 1 time, below process will be occurred.

MICOM Ver. → L C (Lock Closed) → Run (count) → b1, b2, b3, b5, b6, b7

→ F (Fan Motor) → H (Hot V/V)

→ C (Cold V/V) → P (prewashing V/V) → d ( dry V/V) → s(steam V/V) → bb (bubble)

→ dr (drain motor) → CR(circulation) → L O(Lock S/W Open)

2) More details

① When turn on 'LOCK' signal, all process is conducting normaly.

② When working starts, the PCB displays all the sensor conditions.

③ In this case, BLDC Motor is not tested. In order to test it, select spin or rinse.

4-2. LED testing mode

1) Process

After pressing "Wash"," Rinse", "SPIN" button simultaniously, press "POWER" button.

ALL LED On → SPIN button → ALL LED off

2) More tails

① LED test can be done with all LED On.

2323

5. Error Display

MESSAGE

E6 EMG ERROR

ERROR CAUSE SOLUTION

WATER

INLET ERROR

DRAIN

ERROR

UN-BALANCE

ERROR

DOOR

OPEN ERROR

Water level

detection error

OVER

FLOW ERROR

FAN MOTOR

ERROR

LEAKAGE

ERROR

HIGH

VOLTAGE

ERROR

The water tap is closed. Open the water tap. The lter of the valve inlet is clogged. Clean the lter of the valve inlet. The valve inlet is an inferior product or broke down. Change the valve inlet.

The water level sensor (sensor pressure) is an inferior product or broke down.

The drain motor works during water supply. Change the drain motor. The PCB ASS’Y does not check the water level. Change the PCB ASS’Y. The drain hose is kinked or clogged. Clean and straighten the drain hose. The drain motor is an inferior product. Change the drain motor. The valve inlet works during drain. Change the valve inlet The water level sensor is an inferior product . Change the water level sensor. The PCB ASS’Y does not check the water level. Change the PCB ASS’Y. The laundry is concentrated to one side of the drum

during spin.

The Start/Hold button is pressed while the door is opened.

The switch door lock is an inferior product. Change the switch door lock. The PCB ASS’Y does not check the door lock. Change the PCB ASS’Y. Water level is below reset or overow is detected Change the sensor pressure.

The water is supplied continuously due to an inferior valve inlet.

The valve inlet is normal, but the water level sensor (sensor pressure) is inferior.

The drain motor dose not work. (The fan motor is an inferior product or broke down.)

The fan motor does not work. (The fan motor is an inferior product or broke down.)

The PCB ASS’Y does not control the fan motor. Check the connector or change the

Water leaks from the tub or the hose drain. Check the leak of the tub or the hose

The foreign matter is jammed in the drain bellows. (Non-pump model)

The laundry is jammed between the gasket and the drum.

The PCB ASS’Y is an inferior product. Change the PCB ASS’Y. The laundry is jammed between the gasket and the

drum. The motor is an inferior product. Change the motor. The PCB ASS’Y is an inferior product. Change the PCB ASS’Y.

Change the water level sensor (sensor pressure).

Rearrange the laundry.

Close the door.

Change the valve inlet.

Change the water level sensor (sensor pressure).

Change the drain motor.

Change the fan motor.

PCB ASS’Y .

drain. Then change the tub or the hose drain.

Remove the foreign matter in the drain bellows.

Rearrange the laundry.

2424

MESSAGE

E7 DIRECTION

PFE

ERROR CAUSE SOLUTION

MOTOR

ERROR

SENSOR

PRESSURE

ERROR

THERMISTOR

(TEMP. SENSOR)

DRY ERROR

THERMISTOR

WASH ERROR

THERMISTOR

OVERHEATING

ERROR

THERMISTOR

WASH

OVERHEATING

ERROR

WATER TEMP.

ERROR

HEATER

WASH

ERROR

HEATER

DRY ERROR

HEATER

WASH

OVERHEATING

ERROR

PUMP FILTER

ERROR

DRY

The motor spins into an opposite direction. Change the PCB ASS’Y or the

motor.

The motor hall IC is an inferior product or broke down.

The motor is not normally connected. Check the connector of the motor. The motor does not work.

(The motor is an inferior product or broke down.) The water level sensor is an inferior product. Change the water level sensor.

The thermistor dry is an inferior product or broke down.

The thermistor dry is not connected normally. Check the connector of the thermistor

The thermistor wash is an inferior product or broke down.

The thermistor wash is not connected normally. Check the connector of the thermistor

The fan motor does not spin with the proper rpm. (The fan motor is an inferior product or broke down.)

The thermistor dry is an inferior product or broke down.

The heater worked without the water in the tub. Check the water level. The thermistor wash is an inferior product or

broke down.

The water temp. is over 45°C in delicate & wool course.

The heater wash dose not work. (The water temp. doesn't rise over 2°C during 15min.)

The heater dry dose not work. (The water temp. doesn't rise over 3°C during 8min.)

The heater worked without the water in the tub. Check the water level and the heater

The drain pump lter is clogged. Clean the drain pump lter. The drain pump does not work during spin. Change the drain pump. The large amount of detergent was used. Use the proper amount of detergent. The drain hose is placed higher than 1m above the

oor.

Change the motor hall IC or the motor.

Change the motor.

Change the thermistor dry.

dry. Change the thermistor wash.

wash. Change the fan motor.

Change the thermistor dry.

Change the thermistor wash.

Change the heater wash.

Change the heater dry.

wash.

Place the drain hose 1m below the oor

2525

5. ELECTRONIC FIELD PARTS LIST AND SPECIFICATION

No Part Name Part Code Part Code SPECIFICATIONS Q'ty

SWITCH DOOR LOCK

Valve Inlet 3615414820 Common 220-240V 1-WAY HOT PP-BRACKET 1

Valve Inlet 3615415700 Common 100-130 1-WAY HOT PP-BRACKET 1

Valve Inlet 3615415050 New 220~240V, 3WAY, RINSE, GUIDE, PP/BRACKET 1

Valve Inlet 3615405070 New

4 Reactor AS 3615800100 Common DWD-800W RT--046B 1

UNIT DRAIN PUMP AS

6 Unit Steam AS 36189M2U00 New

7 Harness AS

Heater Wash 3612802400 Common 220V 2KW.1R0A721001.RW8TF.IRCA,NPB 1

Heater Wash 3612802440 Common 127V 1KW.1R0A721005.RW8TF1PE.IRCA 1

9 Thermistor Wash 361AAAAB10 Common

10 Unit Motor Universal 36189L4H10 Common

11 Damper Friction 361A700110 Common

12 Unit Bubble Pump AS 36189M2V00 New L=760 1

13 Unit Stator BLDC 36189L620A New 30T 1

14 Unit Rotor BLDC 36189L6300 New 1

15 SWITCH THERMOSTAT 3619046500 Common ON120°C OFF150°C 230V 15A VDE 1

Heater Dry 3612800900 Common

Heater Dry 3612802100 Common

17 FUSE TEMPERATURE 361A800120 Common 128°C DF-128S 15A 250V VDE 1

18 Thermistor Dry 361AAAAD00 New L=200 tube 1

19 CORD POWER AS 3611339950 Common H05VV-F 1.5SQ 250V 16A 1.6M EU-2PIN 6KG 1

20 Unit Fan Motor 36189M2Q00 New 24V DC 14W 1

3619047230 3619047210

36189M1500

36189M1800

3612799A00 New UNIVERSAL_COMBO FULL OPTION 1

3612799B00 DD_COMBO FULL OPTION

3612799C00 UNIVERSAL_WASH FULL OPTION

3612799D00 DD_WASH FULL OPTION

Common Common

DL-S2,250V,16A,BITRON,VE-TYPE DL-S1,124V,16A,BITRON

100~130V, 3WAY, RINSE, GUIDE, PP/BRACKET

AC220V/60HZ HANYU,AL,30W, DUAL PUMP,CIRCUL NEW

AC120V/60HZ HANYU,CU,30W,DUAL PUMP, CIRCUL NEW

230V 900W

R25=1.704K R80=11.981K

DC220/50 G&J 2P PI340 45T(CCA)

70N AKS ST=170-260 DL=197.5 LOW NOISE

220V 2100W 23.05OHM 6.1W/SQ INCOLOY800

1R1A034001

UL120V,1.2kW,1.20Ω,3.5W/ SQ,INCOLOY800,RA8,IR1A34008

1 1

6. WIRING DIAGRAM

2727

DAEWOO ELECTRONICS CORP.

686, AHYEON-DONG MAPO-GU SEOUL, KOREA

C.P.O. BOX 8003 SEOUL, KOREA

TELEX: DWELEC K28177-8 CABLE: “DAEWOOELEC”

S/M NO. :

PRINTED DATE: Nov. 2010

ABOUT THIS MANUAL

VISION CREATIVE. INC

담 당 박성우 님 (서비스메뉴얼)

F.MODEL BUYER

B.MODEL LSE09 BRAND DAEWOO

언 어 영문 COUNTRY

1차

2차

일 정

제 판 인 쇄 애드컴

규 격

MEMO 접수 :

3차

4차

5차

(총 44p) 101118 - 신규 총 22p( 표1,2,3,4,5,9,24~28,30,32~37,39,40,

(총 33p) 101119 - 수정 총 10p(1~33) 101130 - 수정 총 6p(15,16,18,19,20,25) 101201 - 수정 총 2p(17,22) (총 29ㅁp) 101202 - 수정 총 9p(목차,16,17,18,19,22,24,25,26)

(총 30p) 101223 - 신규 총 14p(목차,4~16,26) 110119 - 수정 총 8p(4,5,8,9,12,13,15,16)

41,표4)

서울 종로구 통의동

6번지 이룸빌딩 4층

ELECTROLUX향

연락처

담 당 방 문 수(choi)

VISION

TEL : 730-0660 FAX : 730-3788

Daewoo LSE-09 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual