Page 1
WASHING MACHINE
CCoonntteennttss
1. SPECIFICATIONS..................................................................................................... 1
2. EXTERNAL VIEW..................................................................................................... 2
3. PRINCIPLES OF OPERATION AND EXPLANATION OF FUNCTIONS................ 3
4. DIRECTION FOR DISASSEMBLY AND ASSEMBLY..............................................7
5. TROUBLESHOOTING GUIDE ................................................................................10
6. EXPLODED VIEW AND PARTS LIST.....................................................................15
7. WIRING DIAGRAM..................................................................................................23
Page 2
NO. ITEM SPECIFICATIONS
1 POWER VOLTAGE
SOURCE FREQUENCY 60Hz 50Hz
2 POWER PUMP 515W
CONSUMPTION
NON PUMP 480W
3 DIMENSION NET : 810X435X950, PACKED UP : 870X533X947 (WXDXH)
4 MACHINE PUMP NET : 25kg, PACKED UP : 28kg
WEIGHT NON PUMP NET : 24kg, PACKED UP : 27kg
5 WASHING COURSE STRONG, NORMAL
6 WATER LEVEL HIGH:50l, MEDIUM:52l, LOW:44l
7 REVOLUTION WASH 170 rpm 170 rpm
PER MINUTE SPIN 1700 rpm 1400 rpm
8 TIMER WASH MAX. 15 min., Manual operation
SPIN MAX. 5 min., Manual operation
9 WASHER TYPE PULSATOR TYPE
10 SPIN TYPE CENTRIFUGALLY SEPARATED TYPE
11
MAXIMUM MASS
WASH 6.0 kg
OF TEXTILE SPIN 5.5 kg
12 WATER SUPPLY MANUAL
13 SPIN RINSE O
14 OUTLET OF DRAIN HOSE REAR
15 LINT FILTER O
POWER SOURCE
SUFFIX
EXPLANATION
NON PUMP PUMP
AC 100V 50/60Hz J -
AC 110V 60Hz T TP
AC220V 50Hz N NP
AC 220V 60Hz L LP
AC 240V 50Hz M MP
AC 110/220V 50Hz D AC 127/220V 60Hz S -
1. SPECIFICATIONS
2
SPECIFICATIONS
NOTE : Explanation table for suffix of names.
AC 110V AC 220V AC 127/220V AC 110/220V AC 220V AC 240V
Model Name Pump
DWM-XXXX N P
Power Source
Page 3
2. EXTERNAL VIEW
3
STRUCTURE
Structure Of The Wash Machine
Control Panel (Panel b Ass’y)
11
INLET WATER
Connect inlet hose to supply water in the WASH
TUB or BASKET SPIN.
22
LEVER WATER SUPPLY SELECTOR
Left : water supply in the WASH TUB.
Right : water supply in the BASKET SPIN.
33
WASH TIMER
Use to select the desired time for washing or rinsing.
44
WASH ACTION
Use to select wash action. (STRONG”, “NORMAL”)
55
V ALVE SELECTOR
Select “WASH.RINSE” for washing and rinsing, and
“DRAIN” to drain the water.
(In case PUMP MODEL turn on the drain pump)
“OFF” to turn off the drain pump. (Only PUMP
MODEL)
66
SPIN TIMER
Used to select the desired time for spinning.
Wash Spin
Wash Timer
15
12
9
6
3
0
Wash Action
Strong
Normal
Spin Timer
5
4
3
2
1
0
Off
Wash-Rinse
Valve Selector
Drain
WATER DRAIN HOSE
(PUMP MODEL)
PULSATOR
BASE UNDER
OVERFLOW FILTER
SPIN DRYER LID
When you open this lid while the spin basket is spinning,
the spinning will be stopped by brake system.
LINT FILTER
This is used for gathering the
dregs which are made during
washing.
WASH TUB LID
During operation, close the
wash tub lid.
POWER CORD
The plug’s shape may not correspond with this drawing.
“WARNING-THIS APPLIANCE
MUST BE EARTHED”
SAFETY COVER
INNER LID
SPIN DRYER BASKET.
WATER DRAIN HOSE
(NON-PUMP MODEL)
GUIDE
CASCADE
! #
@
$ % ^
Page 4
FUNCTION
The main switch remains ON during the washing time set by turning the timer knob.
At the same time, the internal switch T1 and T2 which provide power to WASH MOTOR alternately at assigned Intervals.
Select switch knob sets the wash type by means of controlling the interval of internal switch contact.
STRUCTURE AND PRINCIPLE OF ACTIVA TION
3. PRINCIPLES OF OPERATION AND EXPLANATION OF FUNCTIONS
4
CONTROL PANEL
Wash Timer
CIRCUIT DIAGRAM
Page 5
5
PROCEDURE
FUNCTION
The spin timer is the switch providing power to the SPIN MOTOR(DRAIN PUMP MOTOR) during the set spin dry
time, and is a spring-type time switch comes on upon turning and those contact points comes off after the set time.
STRUCTURE AND PRINCIPLE OF ACTIVA TION
1) The main shaft turns due to the unwinding force when the spin timer is turned, the spring wound with that force
being delivered through each gear and the spring slowly unwinding at a speed finally controlled by the angle
assembly .
2) The contact point Turns ON and the assembly angle is set in motion which is in the CAM groove in the OFF
state, comes off the groove when the main shaft is turned to wind the spring. The contact point turns OFF,
return to CAM groove when the spring unwind completely.
SAFETY DEVICE FOR BASKET SPIN
The BASKET SPIN is an apparatus which eliminates the water from the laundry through centrifugal separation
generated by rapid revolution(approximately 1,600rpm for 60Hz). Accordingly, there are a DOOR SWITCH to cut
off the power going into the DOOR SPIN is opened and a brake system to stop the rotating BASKET SPIN.
DOOR SWITCH
When the DOOR SPIN is opened during spinning, the DOOR
SWITCH LEVER which sites atop the DOOR SPIN falls off the
contact, and cuts off the power going into the SPIN MOTOR.
Spin Timer
Page 6
6
PROCEDURE
BRAKE SYSTEM
When the DOOR SPIN is opened, LINK WIRE which connect
to DOOR SPIN loosens. And then the BRAKE BAND touches
the DRUM COUPLING assemply and stops the SPIN DRYER
as it is pulled by the SPRING in the BRAKE FIX PLATE
assembly .
BRAKE BAND GAP CONTROL METHOD
The BAND BRAKE works best when the gap between it and
the DRUM COUPLING is about 2mm when the DOOR SPIN
is closed. The SPIN DRYER stops slowly if the gap between
the two is too narrow, the SPIN DRYER revolution is affected
and the PLA TE CONTROL WIRE may be adjusted to main tain the BRAKE BAND gap adequately.
WASH DECELERATOR ASSEMBLY
The initial deceleration following the activation of the WASH MOT OR takes place through the PULLEY MOTOR
and PULLEY PULSA TOR, and the secondary deceleration is done by the gear in the GEAR HOUSING which also
increeases their revolution strength. This revolution speed and strength is delivered to the PULSATOR, which is
then able to cause water current that is strong yet soft so that wash loads are not damaged.
PLATE
CO NTROL WIRE
BA
BASE
SKET SPI N
MOTOR WASH
About 1,700rpm(60Hz)
1,400rpm(50Hz)
M-Pully
2.5:1 (50Hz)
3.0:1 (60Hz)
PULLEY PULSATOR
About 560rpm(50/60Hz)
PULSATOR
About 170rpm(50/60Hz)
G/H (3.3:1)
WASH M OTOR
Page 7
7
PROCEDURE
GEAR HOUSING ASS’Y
The GRAR HOUSING ASSEMBLY is a transmission device which turns the PULSATOR at 3.3:1 lowered speed
through the gear unit assembly which receives power at the GEAR SHAFT UNIT.
1) The two sides of the GEAR SHAFT UNIT are supported by the
OILLESS BEARING in the GEAR HOUSING ASSEMBLY.
2) The GEAR UNIT ASSEMBLY is connected to the GEAR
SHAFT 1 and GEAR SHAFT UNIT by the GEAR and GEAR
UNIT respectively .
3) The two sides of GEAR SHAFT 1 are supported by the OIL
SEAL and OILLESS BEARING in the GEAR HOUSING
ASSEMBL Y.
SPIN GELLOWS ASS’Y
The wrinkled rubber device on the botton of the BASKET SPIN is
called SPIN BELLOWS ASSEMBLY.
It has a waterseal and a oilless metal inside to prevent leakage
and so that the BASKET SPIN may work smoothly.
Much lint may be obtained depending upon the kind of clothes to
be washed and same of the lint may also be suck to the clothes.
To minimize this possibility , a lint filter is provied on the upper part
of the FIL TER OVERFLOW to filter the wash water.
Use of the lint filter during every wash is recommend.
CLEANING THE LINT FILTER
1) Remove the FILTER AS from the FILTER OVERFLOW by pressing it downwards.
2) Turn the FILTER AS inside out, and wash the lint off with water.
3) Return the FILTER AS it was, and fix the FILTER AS to the FILTER OVERFLOW.
STRUCTURE
Filter
Page 8
8
4. DIRECTION FOR DISASSEMBOY AND ASSEMBLY
DIRECTIONS
1. Remove 3 screws on the panel
3. Remove control lever and timer.
2. Remove knob and 2 screws on the bracket panel.
Replacing Wash Timer And Spin Timer
1. Remove 2 screws on the cover B. 2. Sepeate link brake from the brak wire assembly.
Replacing Motor For Spin And Wash
Page 9
9
CONNECTION
3. Remove bolt and nut on the upper side of the drum
coupling as and lift up the basket spin.
5. Remove a belt connecting motor pulley and pulsator
pulley .
7. Remove cap screw(2EA) and 5 screws on flange
of the tub. And lift up the tub assembly.
9. Remove 3 screws and spin motor.
4. Remove 1 screw fixing the drain pump.
(pump model)
6. Separae harness as connefctors.
8. Remove 3 screw on the base and Remove wash
motor.
Page 10
5. TROUBLESHOOTING GUIDE
10
CONVENIENCE
PROBLEM
Agitator
does not
rotate.
CHECK POINT CAUSE SOLUTION
Pull out the power plug to repair and make sure that the Washing Machine has been properly
grounded.
NOTES
Concerning Wash
Is the Power properly connected?
Is the Fuse blown?
Reconnect the Power Cord.
Change the Fuse.
Is there a whirring sound from the
Wash Motor when turned on?
Is the of Condeser properly
connected?
Motor does not start due to
opening the Condenser circuit
Is the Motor hot?
(In case there is Thermal Protector)
Is the Wiring good?
(Refer to the Wiring Diagram)
Is the connact of Wash T imer good? Defective Wash T imer
Defective Wash Motor
Power has been cut off by
the Thermal Protector.
Improper wiring
Reconnect the Condenser.
Replace Wash T imer
Replace Wash Motor
Reload with proper wash
load.
Power restored when
Motor cools
Reconnect the wiring
Agitator
does not
rotate
smoothly .
Is the Wash Load appropriate?
Are the Agitator and Motor Pulleys
securely assembled?
Does the V-Belt slip?
Are there impurities between the
Agitator and Tub.
Revolution obstructed by
impurities
Remove impurities after
disassembling Agitator
Defect of mechanical
assembly
Worn out V -Belt
Tighten the screws fixed on
the Pulleys.
Replace V-Belt
YES
NO
NO
YES
YES
NO
YES
NO
NO
NO
NO
YES
YES
NO
NO
YES
YES
YES
YES
YES
NO
Page 11
11
EXPLANATION
PROBLEM
Agitator
does not
rotate
smoothly .
CHECK POINT CAUSE SOLUTION
PROBLEM CHECK POINT CAUSE SOLUTION
Connectrning Spin
Does the Gear Housing Shaft
rotate proply when the Agitator
has been disassembled?
Worn out the Serration
within the Agitator.
Defective Gear Housing Replace Gear Housing.
Replace Agitator
Keep the Door Spin *O
closed during spin.
The contact Door Switch is
open.
The Spin
Dryer does
not spin.
Is the Door Spin *O open?
Is the Fuse blown?
Is there a whirring sound from the
Spin Motor when turned ON?
Change the Fuse.
NO
YES
Agitator only
rotates in one
direction.
Is the wiring of Wash condenser
properly connected?
Is the wiring of Wash T imer properly connected?
Impropely Wiring
Defective Wash timer Replace Wash T imer.
Reconnect the Wash T imer.
Improper Connection Reconnect
YES
YES
NO
NO
NO
There is
excessive
noise during
Washing
Are there strange noise frome Tub
when the Agitator rotate?
Agitator improperly
assembled.
Something is in contact with
the Agitator Pulley or Motor
Pulley or other rotating parts.
Adjust the parts so that
there are no impurities in
contact with rotating parts
Tighten the Agitator fixing
screw.
Impurites between Agitator
and tub
Remove impurities after disassembling Agitator.
YES
NO
YES
YES
NO
NO
NO NO
Page 12
12
THE REPAIR
PROBLEM
The Spin
Dryer does
not spin.
There are
strange noise
and servere
vibration during
spinning.
CHECK POINT CAUSE SOLUTION
Is the Condenser properly
connected?
Motor does not start due to
opening the Condenser circuit.
Reconnect.
The Brake Band is touching
the Drum Coupling Assembly .
NO
YES
NO
NO
NO
YES
YES
YES
YES
YES
YES
NO
YES
Brake wire is too long.
Assemble after loosening
Wire Guide Screw and
adjusting downward.
BRAKE SPRING is broken. Replace Brake Spring.
Power has been cut off by
the Thermal Protector
Is the Motor hot? (In case there is
Thermal Protector)
Is the wiring good? (Refer to
Wiring Diagram)
Improper wiring Reconnect wiring
Is the Door Switch Lever properly
placed on the Door Spin *O?
Defective connection
Replace Door Switch or
reshape the Lever.
Is the Door Switch terminal properly connected?
Improper wiring Reconnect the terminal.
Is the Contact of Spin Timer good?
Defective Spin Timer Replace the Spin Timer.
Defective Spin Motor
Spin Dryer does not balanced
due to wash load.
Tub is in contact with the
object sticking out.
Reload the clothes and
press down the Safety
Cover into Spin Basket.
Tighten the Bolt Drum
Coumling Assembly .
Is the assembly between the
Drum Coupling Assembly and
Spin Motor or Spin Dryer loose?
Improper structural assembly
Is the Spin Dryer itself well balanced?
Spin Dryer unbalance Re-assemble Spin Dryer.
Are clothes or the Safety Cover
stick out from Spin Basket?
Reload the clothes so they
are well balanced
Is the wash load well balanced?
Replace the Spin Motor.
Power restored when motor
cools.
YES
YES
NO
NO
YES
NO
NO
NO
YES
NO
Page 13
13
TROUBLE SHOOTING
PROBLEM CHECK POINT CAUSE SOLUTION
The Waterseal or the oilless metal in the Bellows
Assembly worn out.
Replace Bellows Assembly.
There is leakage during
spin drying.
Is the Bellow Assembly properly
assembled?
The Waterseal or the
Oiless Metal in the Bellows
Assembly is worn out.
Replace Bellows
Assembly .
Waterproofing not working
due to defective assembly .
Re-assemble
Bellows Assembly.
YES
NO
YES
YES
Spin Dryer
does not
stop with the
Door Spin
*O open
The Brake Band touches the
Drum Coupling when the Door
Spin *O open.
Brake Band is worn out.
Defective
Door Switch
Is the electric connection of the
Door Switch good?
Replace
Door Switch
The contact of the Door
Switch does not open due
to deformity of the lever of
Door Switch.
Replace Door Switch or
reshape the lever of Door
Switch.
Replace Brake Band or
Brake Fix Assembly .
Brake wire is too short.
Replace after loosening
Wire Guide and adjusting
upward.
NO
NO
Concerning Drainga (Pump)
PROBLEM
Drainage is
not satisfactory
CHECK POINT CAUSE SOLUTIONPROBLEM CHECK POINT CAUSE SOLUTION
Is the height of the drainage area where
the Drain Hose hangs over 1m?
The Drain Hose is too high.
Hang the Drain Hose lower.
Are there impurities in the Drain
Strainer?
YES
NO
NO
Impurities are obstructing
drainage.
Disassemble Agitaor and
take out impurities in drain
Strainer
Impurities are obstructing
drainage.
Are there impurities in the V alve
Housing or Inlet Joint?
Remove impurities or
replace Valve Housing or
Inlet Joint.
Impurities are blocking the
Drain Hose
Remove impurities
YES
YES
NO
Page 14
14
TROUBLE SHOOTING
PROBLEM CHECK POINT CAUSE SOLUTION
Draining
does not
function during drain
selecting
Is the Wash Timer OFF when the Drain
Selector is in the DRAIN position
Pump Motor does not work
because Power is open.
Adjust Wash Timer for adequate draining time.
Is the pump Motor wiring properly
connected?
Defective Pump motor Replace Pump Motor
YES
NO
YES
Defective wiring Reconnect wiring
NO
Drain does
not function
during Spin
drying
Are the wiring of the Spin Timer
and the Pump Motor good?
Defective wiring Reconnect wiring
Is the Spin Timer’s contact good?
Defective Pump motor Replace Pump Motor
NO
YES
Defective Spin Timer Replace Spin Timer
NO
Concerning Drainage (Non Pump)
PROBLEM CHECK POINT CAUSE SOLUTION
NO
NO
Drainage is
not satisfactory .
Are there impurities in the Drain
Strainer?
Impurities are obstructing
drainage.
Are there impurities in the Valve
Housing or Inlet Joint?
Remove impurities or replace
V alve Housing or Inlet Joint
Impurities are blocking the
Drain Hose
Remove impurities
Impurities are obstructing
drainage.
Disassemble Agitator and take
out impurities in Drain Strainer
YES
YES
YES
Water keeps
draining during wash
Is the Drain Selector on the operation Panel at the DRAIN position?
There are impurities
between the impurities
Housing and V alve Bellows.
Remove impurities Or replace
V alve Housing.
Mismanupilation
Turn Drain Selector to
WASH/RINSE position
NO
Page 15
6. EXPLODE VIEW AND PARTS LIST
15
TROUBLE SHOOTING
Assy Panel Back
Page 16
16
TROUBLE SHOOTING
assy panel
NO. PART NAME P ART CORD SPECIFICATION Q’TY REMARKS
P01 KNOB 3613403700 ABS 4.0000
P02 SCREW TAPPING 712240141 1 T2S TRS 4X14 MFZN 3.0000
P03 PANEL B 3614234400 PP 1.0000
P04 HOSE SPRAY 3613201210 LEPE 1.0000
P05 LEVER W.S SELECT 3613702000 PP 1.0000
P06 BRACKET PANEL 3610605500 PP 1.0000
P07 SCREW TAPPING 712240141 1 T2S TRS 4X14 MFZN 2.0000
P08 SWITCH DRAIN 3619043700 VP531A-2H, 250VAC/15A 1.0000
P09 TIMER WASH 3619910940
S-K80NT, SAN, 2SELECT, CONN
1.0000
P10 LEVER CONTROL 3613701400 DWM-3000, POM 2.0000
P1 1 TIMER SPIN 361991 1000 S-800CA, SAN, CONN 1.0000
P12 LINK VALVE 3617804000 PP BAND 1.0000
P13 S/W COVER 3619044800 LIP TYPE 1.0000
P14 SWITCH DRAIN 3619043700 VP531A-2H, 250VAC/15A 1.0000 PUMP
P15 HARNESS DRAIN 3612787400 MSF20/0.18 CONN+187FLAG 1.0000 PUMP
assy accessory
NO. PART NAME P ART CORD SPECIFICATION Q’TY REMARKS
A01 COVER SAFETY 361 1418900 PE-LD 1.0000
A02 LEG 3617702400 PP 4.0000
A03 SCREW TAPPING 712240141 1 T2S TRS 4X14 MFZN 4.0000
A04 HOSE DRAIN O AS 3613224310 L=820MM, NON-CLAMP 1.0000
A05 CLAMP HOSE O 3611202400 HSW -3, 4.0KG 1.0000 PUMP
A06 HOSE DRAIN O 3613222600 4010NP 1.0000 PUMP
A07 GUIDE DRAIN HOSE 3612502300 PP 1.0000 PUMP
Page 17
17
TROUBLE SHOOTING
Assy Tub
Page 18
18
PCB ASS’Y
assy tub
NO. PART NAME P ART CORD SPECIFICATION Q’TY REMARKS
T01 BASE WATER SUPPL Y 3610389500 PP 1.0000
T02 FIL TER OVER FLOW 361 1903700 PP 1.0000
T03 FIL TER AS 3611904000 PP+POLYESTER 1.0000
T04 RING BASKET 3614602300 PP 1.0000
T05 SCREW T APPING 7122401411 T2S TRS 4*14 MFZN 2.0000
T06 BASKET SPIN 3619103300 DWM-800C 1.0000
T07 LINK BRAKE 3617801600 PP BAND W6 1.0000
T08 SPRING COVER 36151 10400 HSW3 1.0000
T09 DOOR SPIN O 3611797800 PP 1.0000
T10 COVER INNER 3611418800 PP 1.0000
T1 1 PLATE T 3614522500 PP 1.0000
T12 BELLOWS AS 3616401800 AS, 800C 1.0000
T13 FIXTURE BELLOWS 3612005000 PP 1.0000
T14 GUIDE CASCADE 3612509000 PP 1.0000
T15 SPECIAL SCREW 3616002901 SUS604 (NON SILOCK) 1.0000
T16 PULSA TOR AS 3619706500 800C 1.0000
T17 CAP SCREW 3610911700 PP 2.0000
T18 TUB 3618817900 PP (JI-360) 1.0000
T19 ROD V ALVE 3618504000 PE-HD 1.0000
T20 BELLOWS V ALVE 4505C06040 NR 1.0000
T21 V ALVE CAP 4505F06013 PE-HD 1.0000
T22 SPRING V ALVE 4505C06022 SWC WR 1.0D 1.0000
T23 CASE V ALVE
361 1131500 PP 1.0000 NON-PUMP
361 1131600 PP 1.0000 PUMP
T24 INLET JOINT 3617504100 PP 1.0000
T25 HOSE OVERFLOW 3613220800 LDPE 1.0000 JAPAN
T26 PROTECTOR F.B 3618303500 NBR 1.0000 PUMP
T27 GEAR HOUSING AS 3617306200 DWF-7510S R=3.3:1 1.0000
T28 SPECIAL BOL T 3616008400 M6 SIDE-FIXING 1.0000
T29 PULLEY PULSA TOR 3618432200 FR-PP GP-2300 1.0000
T30 SCREW T APPING 7122502011 T2S TRS 5X20 MFZN 5.0000
T31 RING O 4506H05050 N. B. R 1.0000
T32 DOOR WASH 361 1797900 PP 1.0000
Page 19
19
WIRING DIAGRAM
Assy Main
Page 20
20
WIRING DIAGRAM
assy main
NO. PART NAME P ART CORD SPECIFICATION Q’TY REMARKS
M01 BELT V 4504B00020 M-25 1.0000
M02 WASHER SPRING 7501008011 SW-8 MFZN 1.0000
M03 NUT HEX 739280001 1 M8*01.25 MFZN 1.0000
M04 PULLEY MOTOR AS
3618431600
PRESS(SGCC1.2T, D31), 4.3MM
1.0000
3618431700
PRESS(SGCC1.2T, D31), 2.1MM
1.0000
M05 SPECIAL SCREW 3616017010 T2 TRS 4X35 MFZN PW 3.0000
3618958100
220~240V/50HZ, W1D35VD050
1.0000 N, NP, M, MP
3618959200 AC 220V/60HZ, WD35UD050 1.0000 L
M06 MOTOR-WA AS 3618959300 AC 1 10V/60HZ, W1D35ED050 1.0000 T, TP
3618959400
AC 100V , 50/60HZ, W1D35BD050
1.0000 J
3618959600
110/240V, 5/60HZ, W1D35GD050
1.0000 S, D
M07 CUSHION MOTOR 3611554500 NR 3.0000
M08 CUSHION MOTOR SPOT 3611554600 PP 1.0000
3618948200 9.7/5.2uF , 400/440, CON-4P 1.0000 N, NP, M
M09 UNIT CAPACITOR
3618948300 10.4/5.2uF , 400/440, CON-4P 1.0000 MP
3618948500 45.6/20.8uF , 200/250, CON-4P 1.0000 T, TP
3618948600 45.6/25uF , 200/200, CON-4P 1.0000 J
M10 CAPACITOR WASH 4509C1 1020 20.8uF*2,200V 1.0000 S, D
M1 1 CAPACITOR SPIN
450E1 11060 16uF, 250V 1.0000 S
4509C1 1010 20.8uF, 200V 1.0000 D
M12 HARNESS CAPACITOR 3612706710 CONN A,B 1.0000 S, D
3612757000
4010DUAL NON-PUMP HARNESS
1.0000 S, D
M13 HARNESS AS
3612757220 DWM-500M, S/NON-PUMP 1.0000 N, M, T, L
3612757230 JAPAN, FILTER 1.0000 J
3612757300
4010SINGLE PUMP HARNESS
1.0000 NP, MP, TP
M14 BASE 3610389400 PP (JI-360) 1.0000
M15 COVER BACK 3611416610 PP (J740) 1.0000
M16 BOLT 734260201 1 6B-2-6X20 POINTING MFZN 1.0000
M17 NUT HEX 739260001 1 6N-2-6 MFZN 1.0000
M18 COUPLING DRUM 3619400300 AL 1.0000
M19 BOLT HEX 734150081 1 6B-1-5X8 MFZN 3.0000
M20 SPRING BRAKE LEVER 3615109000 SWC D1.0 ZN8-C 1.0000
M21 PLATE BRAKE AS 3614517400 ASS’Y, 4.0KG 1.0000
M22 ASSY BRAKE WIRE 3619201702 SUS WIRE+PE L260 1.0000
M23 SCREW TAPPTITE 7272400811 TT3 TRS 4X8 MFZN 1.0000
M24
HARNESS EARTH MOTOR
3612756000 4010 S-MOTOR L=450 1.0000
3618947000 220V, 60HZ, W1D25UE040 1.0000 L
3618947100
220-240V, 50HZ, W1D25VE040
1.0000 N, NP, M, MP
M25 UNIT MOTOR SPIN
3618947200
120-240V, 60HZ, W1D25LE040
1.0000 S
3618947300
1 10-220V, 50HZ, W1D25FE040
1.0000 D
3618947500 110V, 60HZ, W1D25EE040 1.0000 T, TP
3618947600
100V, 50/60HZ, W1D25BE040
1.0000 J
M26 SCREW TAPPING 7122401611 T2S TRS 4X16 MFZN 3.0000
M27 STOPPER UPPER 3615201400 PP 3.0000
Page 21
21
WIRING DIAGRAM
NO. PART NAME P ART CORD SPECIFICATION Q’TY REMARKS
M28 SPRING CUSHION 36151 11900 HSW-3 3.0000
M29 DAMPER 3616900501 NBR 3.0000
M30 STOPPER LOWER 3615201300 PP 3.0000
361 1330800 N LFC-3R, 3X0.75, 2.3M, GY 1.0000
361 1330900 H H05VV-F 3X1.0 2.6M WH 1.0000
361 1331000 RW-300/500, 3X0.75, 2.3M 1.0000
361 1331100 - VCTF, 3X0.75, 2.3M 1.0000
361 1331200 R VCTF, 2X1.25, 2.3M, GY 1.0000
361 1331300 U VDFT, 3X0.75, 2.3M, GY 1.0000
M31 CORD POWER AS
361 1331400 - H05VV-F, 3X0.75, 2.3M, GY 1.0000
361 1331500 P VDFT, 3X0.75, 2.3M, GY 1.0000
361 1331600 - H05VV-F, 3X0.75, 2.3M, BK 1.0000
361 1331700 A-VCTFK, 2X0.75, 2.3M GY 1.0000
361 1331800 F H05VV, 3X0.75, 2.3M, BK 1.0000
361 1331900 N LFC-3R 3X0.75, 2.3M, GY 1.0000
361 1332000 Z H05VV-F, 3X0.75, 2.3M, BK 1.0000
361 1332100 T VCTFK, 2X0.75, 2.3M GY 1.0000
M32 HOSE DRAIN I 3613226400 LD-PE 1.0000
M33 UNIT DRAIN PUMP
3618958300
ASK0LL 220~240V/50HZ-TWIN
1.0000 NP, MP
3618958700
ASK0LL 1 10~120V/60HZ-TWIN
1.0000 TP
M34 HARNESS PUMP 3612787600
MSF20/0.18 2P+250FLAG L=500
1.0000
M35 FIXTURE PUMP 3612005500 PP 1.0000
M36 SCREW TAPPING 7122402011 T2S TRS 4X20 MFZN 1.0000
M37 WASHER PLAIN 7400108411 PW-1-8.4 MFZN 1.0000
Page 22
7. WIRING DIAGRAM
22
WIRING DIAGRAM
Single Voltage/Normal
Single Voltage/Pump
Page 23
23
PARTS DIAGRAM
Dual Voltage/Normal
Single Voltage/Pump-Filter
Page 24
S/M NO. : DW800C0001
DAEWOO ELECTRONICS CO., L TD.
686, AHYEON-DONG MAPO-GU SEOUL, KOREA
C.P.O. BOX 8003 SEOUL, KOREA
TELEX: DWELEC K28177-8
CABLE: “DAEWOOELEC”
FAX: 82-2-360-7877
TEL: 82-2-360-7114
http://www.dwe.co.kr
PRINTED DATE: OCT.2000
Page 25
Service Manual
W ashing Machine
Model :
DWM-800C(P)
DAEWOO ELECTRONICS CO., LTD.
Loading...