=
DWM-5024
WASHER-SPINDRYER
INSTRUCTION MANUAL
• Thank you for selecting this washer-spindryer.
• Before operating this unit, please read these
instructions completely.
• When you install this unit, be sure to assemble legs
to BASE.
• The appliance is not intended for use by young
childron or infirm person whithout supervision.
• Young children should be supervised to ensure that
they do not play whith the appliance,
• If the supply cord is damaged, it must be replaced by
the manufecturer or its service agent or a similarly
qualified person in order to avoid a hazard.
• If the appliance is supplied from a cord extension set
or electrical portable outlet device, it should be
positioned so it is not subjected to splashing or
ingress of moisture.
WASH TIMER
M
I
I
T
L
N
O
I
T
A
T
O
R
VALVE SELECTOR
M
I
I
T
L
N
O
I
T
A
T
O
R
SPIN TIMER
2
PARTS IDENTIFICATION
ACCESSORY
R
O
T
A
T
I
O
N
L
I
M
I
T
R
O
T
A
T
I
O
N
L
I
M
I
T
•TUB
•OVERFLOW FILTER
•WASHER LID
•DRAIN STRAINER
•PULSATOR
•BASE
•SPINDRYER LID
•INNER LID
•SPINDRYER DRUM
•GROUND WIRE
(OPTION)
•POWER CORD
Control panel
SPIN TIMER
0
MIN
1
2
3
4
5
WASH TIMER
R
O
T
A
T
I
O
N
L
I
M
I
T
O
F
F
W
A
S
H
•
R
I
N
S
E
D
R
A
I
N
VALVE SELECTOR
0
MIN
3
6
9
12
15
R
O
T
A
T
I
O
N
L
I
M
I
T
!!
Water Inlet
Connect the hose from the water faucet to feed water to the tub.
@@
Wash T imer
Use to select the desired time for washing or rinsing.
##
Drain Selector
Select “WASH · RINSE” for washing and rinsing, and “DRAIN” to drain the tub.
“OFF” to turn off the drain pump. (Model with pump)
$$
Spin Timer
Use to select the desired time for spinning.
LEG (4EA) SAFETY COVER
DRAIN HOSE
NON PUMP
PUMP
!! @@ ##
$$
Caution (Only for Dual Voltage Model)
• Make sure that the electric connector is set for your available voltage before operating the washing
machine. This unit is set for 220V . If you want to change the voltage, remove the back cover and reset
the connector as figures.
INSTALLATION
Caution: If the power cord is damaged, it should be replaced by a repair shop appointed by the
manufacturer , because special purpose tools are required.
Caution: Do not connect the grounding wire to the gas pipe, lightning arrester, telephone connector.
etc.
3
Grounding Wire
• Connect the grounding wire(option) to a water faucet if the pipe is made of metal, before plugging the
power cord into the socket.
If the water supply pipe is made of a synthetic material like vinyl, it is not possible to ground the machine
to the water supply pipe, another ground source must be found.
Electric Connection
•
This unit is designed to operate from an adequate supply mentioned at the rating label sticked to the rear of it.
• For maximum security, attach the grounding wire to a copper plate or grounding rod and bury it at least
20cm in the ground.
How to Fix Legs
• When you install this unit, be sure to assemble legs(4EA) to BASE.
• Place this unit on its rear side on a carton to prevent damage to body.
• Slide the leg into the opening underneath the BASE, and push.
Gas Pipe
Grounding Wire
Grounding Rod
More than
20cm
4
Connection of Hoses
• Attach the water intake hose to the water inlet located at
the left-hand side of the control panel. Press fit the other
end of the hose to either a hot or cold water tap as required.
• Attach the drain hose to the drain outlet at the rear of the base.
• The drain hose should be laid flat on the ground. Water flow will be restricted if any portion of the drain
hose is raised from the ground. (NON PUMP)
• Hang up the drain hose on the edge of a sink. (PUMP)
Caution: This unit is made of poly propylene, use water
below 50°C
Caution: The opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor .
WASH TIMER
R
O
T
A
T
I
O
N
L
I
M
I
T
VALVE SELECTOR
SPIN TIMER
R
O
T
A
T
I
O
N
L
I
M
I
T
WORLD WASH
• Sort the clothes into groups-whites, colorfast, non-colorfast, delicates, lint free, lint producer, etc., and
wash according to the LAUNDRY GUIDE.
• Clothes with worn patches or tears should first be mended. Empty out all pockets and close all side
fasteners. Treat bad stains prior to washing.
• Ensure the drain hose is in its correct position. (See INSTALLATION)
• Inlet power cord plug into the power point and switch on.
!
Set the wash timer knob to position “0” and set the drain selector to the “WASH · RINSE” or “OFF” position.
@ Open the water faucet and feed water to the water level indicated inside the wash tub.
# Put the detergent and laundry into the wash tub.
$ Set the wash time with the wash timer.
% When washing is finished, set the drain selector to the “DRAIN” position and drain the wash tub.
HOW TO WASH
Preparation
How to Wash
(NON PUMP) ( PUMP)
Less than 10cm
Drain Outlet
Drain hose
Hose Clamp
A
! Set the drain selector to the “W ASH · RINSE” position.
@ Turn the water tap on.
# When the rinsing water becomes clear, turn off the water tap.
$ Set the drain selector to the “DRAIN” position to discharge the water.
! Set the drain selector to the “W ASH • RINSE” or “OFF” position.
@ Turn the water tap on and supply proper amount of water to the wash tub.
# Adjust the wash timer in accordance with the clothes to be rinsed.
$ Set the drain selector to the “DRAIN” position to discharge the water.
5
HOW TO RINSE
Overflow Rinse
Water Saving Rinse
Note: Before rinsing, the wash load may be transferred to the spindryer drum for spinning for 2~3
minutes (approx.) to remove suds(See HOW TO SPIN DRYING).
On completion, transfer the wash load to the wash tub for rinsing.
! Put the wet clothes into the spindryer drum, being sure that they are well balanced as shown below.
@ Place the safety cover horizontally on the top
# Close the inner lid and spindryer lid. (The machine will not spin if the spindryer lid is open.)
$ Turn the spin timer to the clockwise direction until you reach the desired spin time position.
• If there is any abnormal vibration during spinning, open the spindryer lid to stop the spindryer drum and
rearrange the clothes to be in good balance.
• Should spinning fail to stop within 15 seconds after spindryer lid is open, the brake is out of
order . Immediately stop using the machine and request repair service.
HOW TO SPIN DRYING
Caution: Ensure that the spindryer drum completely stops before reaching in to remove the laundry.
Be specially careful of children.
At the end of every washing:
• Switch off the electricity of the power point.
• Check that both timers are set to the “O” position.
• Wipe off spillage (detergent powder,etc.), and generally wipe over the tub and base with a dry duster.
ƒRCleaning after use will extend the life of your washing machine. Before cleaning disconnect the power
cord from the electrical outlet.
• Remove the overflow Filter by pulling it forward.
• Wash off the lint stuck on the overflow Filter during overflowing.
•
Re-install the overflow Filter: By first inserting its bottom section and then pushing the upper part firmly into place.
• Dirt maybe also collected underneath the pulsator.
• Clean out occasionally by remove the screw located in the
center of the pulsator .
• Hook the pulsator and pull upwards.
• Wash off the lint stuck on the bottom of the wash tub.
(When replacing the pulsator, make sure that the screw must be firmly tightened
)
LAUNDRY GUIDE
Overflow Filter
Pulsator
CLEANING AND MAINTENANCE
Water Level Degree of Water Wash Spin
Type of Fabric Wash load
(Volume) Soiling Temperature Time Time
Full
High Heavy Hot 50°C Max
Cotton and
(App. 49\) Normal Warm 40°C
Linens
Half or Low
15 min. 5 min.
Less (App. 35\)
Light Warm 40°C
Full High Normal 4~5 min.
Nylon
(App. 49\)
Half or Low Light
Warm 40°C
2~3 min.
2 min.
Less (App. 35\)
Delicates
Half or High Normal
Less (App. 49\) to Light
Warm 40°C 2~3 min. 1~2 min.
6
7
• Use a screwdriver to loosen the screw of the pulsator, and remove the pulsator.
• Remove the drain strainer from the bottom of the tub using a sharp tool such as a driver.
• Wash off the lint stuck in the strainer.
• Re-install the drain strainer and pulsator.
Drain Strainer
• Avoid using excessive amounts of bleach, soap powder of detergent. Use the amount recommended
by the respective manufacturers.
• If the machine is installed in areas subject to freeze, ensure that it is completely drained after use.
• When washing delicates e.g., silks, fine nylons, laces, etc., it is advisable to place them in a mesh bag
to prevent the possibility of damage.
• Do not wash lint attracting fabrics with lint producers, e.g., black socks or dark colored jumpers with
white fluffy towels, napkins, etc.
• Avoid placing a wet load on the control panel.
There may be times when you suspect your washing machine requires maintenance. Before calling for a
service engineer , please check the following points, to save unnecessary cost. You may be pleasantly
surprised that an apparent malfunction can be easily rectified as follows.
If your washing machine will not start, check whether
• The house circuit breaker is tripped or a fuse is blown.
•The cord is firmly connected to the power point or the power point is not switched on. (Check with a
small table lamp or toaster , etc.)
• Something is preventing the pulsator from rotating.
• The wash timer is set.
If the spin dryer will not operate, check whether
• The spindryer lid is closed.
• The spin timer is set.
If there is excessive noise, check whether
• Something is touching the pulsator as it rotates.
• The machine is placed on a level surface.
• The clothes in the spindryer drum is excessively unbalanced during spinning.
• An article is lodged between the spindryer drum and tub.
POINTS TO REMEMBER
BEFORE YOU CALL FOR SERVICE
* Design and specifications could be changed without notice.
8
SPECIFICATIONS
Full name of appliance Electric clothes washing machine
Intended use Household
Type of Appliance Twin-tub
Power source Refer to specification LABEL
Dimensions (unit:mm) 802
¡¿440¡¿937(W¡¿D¡¿H)
Appliance Weight 22.5kg (NON PUMP), 23.5kg (PUMP)
Rated operating time
Washing: 1 hour operation
Spinning: 15min. operation
Protection against electric shock Class 1 appliance
Protection against moisture Splash-proof Appliance
Standardized water consumption 49| (High), 42| (Medium), 35| (Low)
Operating pressure 0.3kgf/cm
2
~ 8kgf/cm2(29.4kPa~784kPa)
Loading...