Daewoo DTL-29U8ZLP, DTL-29U8ZZP, DTL-29U8ZLS, DWL-28W8ZLS, DWL-28W8ZLP Service Manual
...
Service Manual
Colour Television 68 Cm / 66 Cm WIDE STEREO
CHASSIS : CP-810F / WP-811F
DAEWOO ELECTRONICS CO., LTD
http://svc.dwe.co.kr
Apr. 2002
MODEL :DTL-29U8ZLP / DTL-29U8ZLS
DTL-29U8ZZP / DTL-29U8ZZS
DWL-28W8ZLP / DWL-28W8ZLS
DWL-28W8ZZP / DWL-28W8ZZS
S/M No: CP810WP811
Specifications
WP-811F CP-810F
THOMSON
28" FLAT : W66EJY011X121 29" FLAT : A68EJZ011X121
SAMSUNG
28" FLAT : W66QDE993X ... 29" FLAT : A68QCP893X ...
SYSTEM
Main Voltage
Power Consumption
Sound Output
Speaker
Antenna Impdeance
Tuning System
Tuner
Number of Program
Aux. Terminal
Remote Controller
Teletext
OSD Language
R-22D06 with 2 "AAA" type batteries
TOP(5 Page memory) & FLOF(7 Page memory)
- West option : English, German/Dutch/Flemish, French, Italian, Spanish/Portuguese,
Swedish/Finnish/Danish, Hungarian, Rumanian, Turkish
- West : English, German, French, Italian, Spanish, Nethelands, Swedish
75 ohm unbalanced input (Din Standard)
Frequency Synthesize(FS) Tuning System
UV1316/A(Philips), DT5-BF18D(Partsnics), EL2782-105-B(Siel)
100 programs
12W 8ohm x 2 EA
CRT
21 pin EURO-SCART jack (AV input, TV output, RGB input)
21 pin EURO-SCART jack (AV input, S-VHS input)
RCA type AV input jack
S-VHS jack
Headphone jack
PAL/SECAM-B/G,D/K,PAL-I/I',SECAM-L/L' NTSC-3.58/4.43 (Play back)
230V AC, 50Hz
Stand-by mode : 2.0Watts
Normal operating mode : 120 Watts
10 + 10 Watts, 10% THD at RF 60% mod. (1kHz)
✔
Caution
: In this Manual, some parts can be changed for improving, their
performance without notice in the parts list. So, if you need the
latest parts information,please refer to PPL(Parts Price List) in
Service Information Center (http://svc.dwe.co.kr).
1
TABLE OF CONTENTS
SAFETY INSTRUCTION .................................................................................................................. 2
SPECIFICATIONS ............................................................................................................................ 3
CIRCUIT BLOCK DIAGRAM ........................................................................................................... 4
ALIGNMENT INSTRUCTION ........................................................................................................... 5
SCHEMATIC DIAGRAM .................................................................................................................. 12
EXPLODED VIEW ............................................................................................................................ 14
PRINTED CIRCUIT BOARD ............................................................................................................ 16
SERVICE PARTS LIST .................................................................................................................... 19
APPENDIX (" Appendix is provided only by internet [http://svc.dwe.co.kr] ")
IC DESCRIPTION ............................................................................................................................. 1
IC DC VOLTAGE CHARTS .............................................................................................................. 18
2
SAFETY INSTRUCTION
WARNING
: Only competent service personnel may carry out work involving the testing or repair of this equipment
1. Excessive high voltage can prodece potentially hazardous X-RAY RADIATION. To avoid such hazards,
the high voltage must not exceed the specified limit.
The nominal value of the high voltage of this receiver is
29-31kv at max beam current. The high voltage must
not, under any circumstances, exceed 35kv. (33kv :
SAMSUNG CRT)
Each time a receiver require servicing, the high volt-
age should be checked. It is imprortant to use an accurate and reliable high voltage meter.
2. The only source of X-RAY Radiation in this TV receiver
is the picture tube. For continued X-RAY RADIATION
protection, the replacement tube must be exactly the
same type tube as specified in the parts list.
X-RAY RADIATION PRECAUTION
1. Potentials of high voltage are present when this
receiver is operating. Operation of the receiver outside
the cabinet or with the back board removed involves a
shock hazard from the receiver.
1) Servicing should not be attempted by anyone who is
not thoroughly familiar with the precautions necessary when working on high-voltage equipment.
2) Dischange the high potential of the picture tube
before handling the tube. The picture tube is highly
evacuated and if broken, glass fragments will be
violently expelled.
2. If any Fuse in this TV receiver is blown, replace it with
the FUSE specified in the Replacement Parts List.
3. When replacing a high wattage resistor ( oxide metal
film resistor ) in circuit board, keep the resistor 10mm
away from circuit board.
4. Keep wires away from high voltage or high temperature components.
5. This receiver must operate under AC230 volts, 50Hz.
NEVER connect to DC supply or any other power or
frequency.
SAFETY PRECAUTION
Many electrical and mechanical parts in this have
special safety-related characteristics. These characteristics are often passed unnoticed by a visual
inspection and the X-RAY RADIATION protection
afforded by them cannot necessarily be obtained by
using replacement components rated for higher voltage, wattage, etc. Replacement parts which have
these special safety characteristics are identified in
this manual and its supplements, electrical compo-
nents having such features are identified designated
symbol on the parts list.
Before replacing any of these components, read the
parts list in this manual carefully. The use of substitute
replacement parts which do not have the same safety
characterisitics as specifide in the parts list may create
X-RAY Radiation.
PRODUCT SAFETY NOTICE
3
PIN Signal Designation Matching Value
1 Audio Out (linked with 3)
0.5Vrms, Imp < 1 k (RF 60% MOD)
2 Audio In (linked with 6)
0.5Vrms, Imp < 10 k
3 Audio Out (linked with 1)
0.5Vrms, Imp < 1 k (RF 60% MOD)
4 Audio Earth
5 Blue Earth
6 Audio in (linked with 2)
0.5Vrms, Imp < 10 k (RF 60% MOD)
7 Blue in
0.7Vpp 2dB, Imp 75
8 Slow (Function) Switching
TV : 0-2V, PERI : 9.5 - 12V, Imp > 10 k
9 Green Earth
10 NC
11 Green In
0.7Vpp 2dB, Imp 75
12 NC
13 Red Earth
14 Rapid(Blanking) Switching Earth
15 Red In, C In
0.7Vpp 2dB, Imp 75
16 Rapid(Blanking) switching
Logic 0 : 0 - 0.4V, Logic 1 : 1 - 3V, Imp 75
17 Video Earth
18 Rapid Blanking Earth
19 Video Out
1Vpp 2dB, Imp 75
20 Video In, Y In
1Vpp 2dB, Imp 75
21 Common Earth
SPECIFICATIONS
+
-
+
-
+
-
+
-
+
-
4
CIRCUIT BLOCK DIAGRAM
SVM
SVM
S-CORRECTION
LINE FILTER
[LF-24A3]
SMPS IC
[STR-F6656]
SMPS TRANS
[TSM-5345B8
7V
14V
+14V
-14V
+15V
-15V
143V
[1372.0078]
5
ALIGNMENT INSTRUCTIONS
User Remocon
1. R-22D06
TV................................TXTTV...................................TXT
VOLUME...............VOLUME
MENU.......................MENU
POWER.................POWER
DOWN ..................DOWN
(CURSOR LEFT)
PR UP..........................PAGE UP
(CURSOR UP)
VOLUME UP...........VOLUME UP
(CURSOR RIGHT)
PR DOWN..............PAGE DOWN
NORMAL .................... Not used
A V .............................. Not used
TXT ............................. Not used
Not used ...................... INDEX
Not used ...................... C
Zoom ..................Double Window
SOUND ....................... Not used
MODE
MUTE .......................... MUTE
(CURSOR DOWN)
Not used ....................... Size
Not used ....................... Y
EFFECT ....................... Not used
R-22D06
SLEEP...................Not used
Not used................CANCEL
Not used................... HOLD
RECALL...............SUBPAGE
STILL......................REVEAL
Not used ..........................R
Not used ..........................G
PR ......................... PAGE
NUMBER NUMBER
0-9 0-9
6
* How to Enter the “ Service Mode ” with user remocon.
1) Set the TV Pr 91
2) Sharpness “ MIN “ control.
3) Push the Red, Green, Menu buttons in regular sequency within 5 seconds after setting TV power off.
4) You can see the Menu of “ service mode “ on the screen.
5) The PR UP/DOWN buttons on the remote controller are used to move the selection bar up or down the Menus.
6) The VOL UP/DOWN buttons on the remote controller are used to adjust levels.
7) If you want to exit from “ Service Mode “ then power the TV off.
- You can see the SVC Menu by OSD in TV set.
Tuner is
Flat Option
Svm SVG
Svm SVD
Svm SVDEL
Svm SVCOR
Bcl Thres
Bcl Tc
Bcl Gain
Nor1 Bright
Nor1 Cont
Nor1 Color
Nor1 Sharp
Nor1 Tint
Nor2 Bright
Nor2 Cont
Nor2 Color
Nor2 Sharp
Nor2 Tint
Dolby3411
PHI
YES
015
003
004
008
378
030
240
038
058
035
030
032
040
035
030
025
032
YES
V. Slope
V. Center
V. Size
S. Curve
H. Center
H. Width
EW. Para
EW. Cor Top
EW. Cor Low
EW.Sym
R. Bias
G. Bias
B. Bias
R. Drive
G. Drive
B. Drive
G2 Adjust
Sub bright
Double TEXT
Wide Option
000
906
203
025
-157
090
365
030
020
025
400
452
430
350
287
272
960
000
776
NO
SVC v1
ALIGNMENT INSTRUCTIONS
Alignment Instructions for WP-811F/CP-810F Chassis
1PAGE
DWL-28W8ZLP DWL-28W8ZLS DTL-29U8ZLP DTL-29U8ZLS
V. Slope 000 000 000 006
V. Center 030 026 906 896
V.Size 237 062 203 041
S.Curve 024 024 025 029
H.Center -145 -143 -157 -151
H.Width 105 084 90 029
EW.Para 419 442 365 404
EW.Cor Top 007 023 030 034
EW.Cor Low 009 022 020 018
EW. Sym 011 000 025 000
R Bias 400 400 400 400
G Bias 451 451 452 452
B Bias 437 437 430 430
R Drive 350 350 350 350
G Drive 278 278 287 287
B Drive 267 267 272 272
G2 Adjust 960 960 960 960
Sub Bright 000 010 000 010
Double TEXT 776 776 776 776
Wide Option YES YES NO NO
2PAGE
Tuner Is PHI PHI PHI PHI
Flat Option YES YES YES YES
Svm SVG 015 024 015 024
Svm SVD 003 002 003 002
Svm SVDEL 004 002 004 002
Svm SVCOR 008 015 008 015
Bcl Thres 378 378 378 378
Bcl Tc 030 030 030 030
Bcl Gain 240 240 240 240
Nor1 Bright 038 038 038 038
Nor1 Cont 058 058 058 058
Nor1 Color 035 035 035 035
Nor1 Sharp 030 030 030 030
Nor1 Tint 032 032 032 032
Nor2 Bright 040 040 040 040
Nor2 Cont 035 035 035 035
Nor2 Color 030 030 030 030
Nor2 Sharp 025 025 025 025
Nor2 Tint 032 032 032 032
Dolby 3411 YES YES YES YES
7
ALIGNMENT INSTRUCTIONS
8
AFT
Standard B/G, D/K, I and L
1) Set a Signal Generator with
- RF FREQUENCY = 38.9 MHz,
- RF OUTPUT LEVEL = 80 5dBuV
- Pattern = Color Bar
- System = PAL-B/G
2) Connect the Signal Generator RF Output to TP2 (Tuner IF Output).
There must be no signal input to the tuner.
3) Set the L103 to TP1(I101, #22) with DC Voltage to 2.5V 0.1V
AGC
1) Set a Pattern Generator with RF LEVEL "63dBuV(Philips, Siel) / 70dBuV(Partsnic)",
RF Frequency 487.25MHz(23CH), Pattern Color Bar.
+
-
+
-
ALIGNMENT INSTRUCTIONS
2) Connect a OSCILLOSCOPE PROBE to P101 (TUNER AGC INPUT).
3) Set the RBO2 to P101(Tuner AGC Input) with DC Voltage to 3.0V 0.1V
SCREEN (G2)
1) Set a Pattern Generator with - RF Frequency : 210.25MHz (10CH)
- Pattern : RETMA
2) Select the “ G2” in Menu
3) And a Horizontal Line will appear on the screen.
4) Adjust the SCREEN VOLUME on FBT barely to see the Horizontal Line.
5) Press the PR UP/DOWN keys to finish the SCREEN adjustment.
FOCUS
1) Apply a RETMA PATTERN signal.
2) Adjust the FOCUS VOLUME on FBT to obtain optimal resolution.
GEOMETRY
1. VERTICAL SLOPE ( Fixed : Adjust if need be )
1) Apply a RETMA PATTERN Signal.
2) Set the TV to Normal I mode.
3) Adjust the higher semicircle and the lower semicircle to be the same, with the V.Slope
by volume Up/Down keys.
2. VERTICAL CENTER
1) Apply a RETMA PATTERN Signal.
2) Set the TV to Normal I mode.
3) Adjust the center of the picture with the V.Center by volume Up/Down keys.
+
-
9
3. VERTICAL SIZE
* The VERTICAL CENTER adjustment has to be done in advance.
1) Apply a RETMA PATTERN Signal.
2) Set the TV to Normal I mode.
3) Adjust the VERTICAL SIZE of the picture with the select V.size by
volume UP/DOWN keys.
4. VERTICAL S-CORRECTION ( Fixed : Adjust if need be )
1) Apply a CROSSHATCH PATTERN Signal.
2) Adjust the S-CORRECTION to obtain the same distance between
horizontal lines with the S.Curve by volume UP/DOWN keys.
5. HORIZONTAL CENTER
1) Apply a RETMA PATTERN Signal.
2) Adjust picture centering with the select H.Center by volume UP/DOWN keys.
EW
1. WIDTH
1) Apply a RETMA PATTERN Signal.
2) Adjust the horizontal width to make a perfect circle with the select H.Width
by volume UP/DOWN keys.
2. PARA
1) Apply a CROSSHATCH PATTERN Signal.
2) Adjust the vertical line to straight with the select E.W Para by volume
UP/DOWN keys.
3. CORNER ( Fixed : Adjust if need be )
1) Apply a CROSSHATCH PATTERN Signal.
2) Adjust the vertical line to straight with the select EW.Cor T by volume
UP/DOWN keys.
4. SYMMETRY ( Fixed : Adjust if need be )
1) Apply a CROSSHATCH PATTERN Signal.
2) Adjust the symmetrical balance to be suitable with the select EW Sym by
volume UP/DOWN keys.
ALIGNMENT INSTRUCTIONS
10
WHITE BALANCE
1. RGB Reference R
2. Beam Reference LOW ( 288, 301 : 10Cd/ )
HIGH ( 288, 301 : 100Cd/ )
3. Adjust G, B Gain with select Menu G,B of BIAS, DRIVE of select Menu so that R, G, B Bars
are on the center position of the analog meter. If R Analog meter is not on center, control
the Brightness +/- of user Remocon so as R Analog meter to be on the center position.
SUB BRIGHT
1. Pattern : Retma
2. Adjust the SUB BRIGHT with the select Sub Bri by volume UP/DOWN keys.
so that only H-Center parts of picture can be seen.
DOUBLE TEXT CENTER
1. Pattern : Pattern RED
2. Select Menu
3. Select DT in SVC menu time to see the Double Text Picture.
( Left : RF Picture, Right : Text Picture )
4. Change the Double Text control keys volume UP/DOWN keys so that the left edge of text
picture concur with the right edge of RF picture.
WIDE MODE
1. Locate the cursor on ‘ Wide’ in SVC Menu.
2. ‘ Yes’ changes the display to 16:9 mode.
3. ‘ No’ change the display to 4:3 mode.
m
2
m
2
ALIGNMENT INSTRUCTIONS
FLAT MODE
1. Locate the cursor on ‘ FLAT’ in SVC Menu.
2. ‘ Yes’ changes the display to FLAT CRT mode.
3. ‘ No’ change the display to Normal CRT mode.
TUNER SELECTION
1. DWE : Partsnic Tuner
2. PHI : Philips Tuner
3. SIE : Siel Tuner
11
SVM (Scan Velocity Modulation)
1. SVM SVG : SVM Gain
2. SVM SVD : SVM Differentiator delay (0 = filter off)
3. SVM SVDEL : Delay of SVMOUT in steps of 12.5nS
2. SVM SVCOR : SVM coring value
ALIGNMENT INSTRUCTIONS
BCL (Beam Current Limit)
1. BCL Thres : BCL threshold current
2. BCL TC : BCL time constant
3. BCL Gain : BCL loop Gain
12
SCHEMATIC DIAGRAM
13
14
EXPLODED VIEW
DTL-29U8ZLS / DTL-29U8ZZS
15
DWL-28W8ZLS /DWL-28W8ZZS
EXPLODED VIEW
16
PRINTED CIRCUIT BOARD
Loading...