Daewoo DWD-FU107’S, DWD-FD147’S, DWD-FU127’S Instruction Manual

" Economic wash system

Using artificial intelligence, the washer uses minimum energy and water by selecting optimal water level and washing time.

" Low noise system

The washer minimizes the washing and spinning noises by sensing the amount of laundry.

" Child-Lock

The Child-Lock system has been used to prevent children from pressing any button to change the program during operation.

" Nano-silver sterilization washing(Option)

By applying very fine silver particles on essential parts inside, the washer sterilizes up to 99.9% as is done by boiling wash.

" Air bubble washing(Option)

This is an advanced technology that generates millions of air bubbles inside the drum on washing sequence, and the bubbles dissolve the detergent particles completely and cleanse all the soil in clothes gently and neatly.

INSTRUCTION MANUAL

DWD-FU107’S/FU127’S/FD147’S

Washing Machine Instruction Manual

CONTENTS Page

A NOTE T O YOU

Thank you for buying a DAEWOO appliance. DAEWOO washers are easy to use, save time, and help you manage your home better. This manual contains valuable information about how to operate and maintain your washer properly and safely. Please read it carefully.

PARTS AND FEATURES.................................................................................................................2

WASHER SAFETY...........................................................................................................................3

INSTALLATION INSTRUCTIONS....................................................................................................4

INLET HOSE CONNECTION...........................................................................................................5

ELECTRICAL REQUIREMENTS .....................................................................................................6

OPERATING YOUR WASHER........................................................................................................7

THE FUNCTIONS OF THE CONTROL PANEL...............................................................................9

WASHING PROCEDURE AND PROGRAM SELECTION.............................................................11

MAINTENANCE .............................................................................................................................19

HOW TO CLEAN THE FILTER......................................................................................................20

REMOVING STAINS......................................................................................................................21

TROUBLE SHOOTING ..................................................................................................................22

SPECIFICATION & WIRING DIAGRAM ........................................................................................23

PARTS AND FEATURES

The parts and features of your washer are illustrated on the page. Become familiar with all parts and features before using your washer.

Accessories

NOTE

The drawings in the book may vary from your washer model. They are designed to show the different features of all models coverd by this book, Your model may not include all features.

Hose drain Inlet hose Manual Cap holder(3EA)

DETERGENT CASE

INLET HOSE

HOT

(OPTION)

COLD

DOOR

LOWER COVER

ADJUSTABLE LEG

HOSE DRAIN

CONTROL PANEL

POWER CORD

" DWD-FU107’S/FU127’S/FD147’S SERIES

Save these instructions

Your safety is important to us. To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the following basic precautions.

Understanding your responsibilities

• Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same wash. Hazardous fumes can form.

• Unplug power supply cord before attempting to service your washer.

• Do not wash fiberglass material. Small particles can stick to fabrics washed in following loads and cause skin irritation.

• Do not spray water on the control panel of the washer. It could cause fire or an electric shock.

• In case of the dual valve model, if you connect only cold water inlet valve, while water temperature is selected as hot or warm, there can be water leakage from unconnected water inlet valve.

• This appliance must be grounded. To avoid electrical shock, use a metal pipe for the ground connection.

WASHER SAFETY

• Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.) should not be used or stored in or near your washer. Do not add flammable fluids to your wash water.These substances give off vapors that can create a fire hazard or explosion.

• After starting a cycle, do not reach into the washer until all motions stop.

• Do not tamper with the controls.

• The appliance is not intended for use by young children or infirm persons without supervision.

• If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent or a similarly qualified person in order to avoid a hazard.

• If the appliance is supplied from a cord extension set or electrical portable outlet device it should be positioned so that it is not subjected to splashing or ingress of moisture.

Please ...

• Have only a qualified person install, repair, or replace parts on washer.

• Maintain washer properly.

• Protect washer from the weather and keep it where the temperature will not fall below freezing.

• Do not install the washer at a place of extremely high humidity. It could cause an electric shock or a short circuit.

• Connect washer to the correct outlet, electrical supply, water supply, and drain supply.

Read all instructions before using your washer

Removing transit bolts

1. Before operating the washer, remove the transit bolts(3ea) along with the rubber.

• If the bolts are not removed, it may cause

heavy vibration, noise and malfunction.

2. Unscrew the 3 bolts with the 10mm hex wrench or spanner or cross-tip screwdriver. Keep the 3 bolts for a later time.

• When the appliance is transported, transit

bolts will be re-used.

3. Close the holes with the cap holders supplied.

Location of washer

• Check location where the washer will be installed. Make sure you have everything necessary for correct installation.

• Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.

• Do not place or store laundry products on top of washer at any times.

• Install the washer on the horizontal solid floor.

If the washer is installed on an unsuitable floor, it could make considerable noise, vibrate severely and cause a malfunction. If the washer is not level, adjust leg up or down for horizontal installation.

• Ventilation openings must not be obstructed by carpeting when the washer is installed on a carpeted floor.

• Leave some space (right & left : 2cm, rear : 10cm).

• In case of built-in installation, the distance between top of the washer

and bottom of upper plate should be at least 3mm.

INSTALLATION INSTRUCTIONS

Laundry

Tub

Washer

approx.

2cm

Drain Hose

The washer should be connected to the water mains using new hose sets and old hose sets should not be reused. In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water inlet valve. Option : Be careful not to confuse hot water inlet and cold water inlet.

For Ordinary Tap

INLET HOSE CONNECTION

1 Pull down the collar of

the inlet hose to separate it from the water tap adapter.

2 Loosen the four screws

properly in fitting into water tap.

3 Fit the water tap adapter

into the water tap and tighten the four screws evenly while pushing up the adapter so that the rubber packing can attach to the water tap tightly.

1 Connect the inlet hose to

the water tap by screwing the connector tightly.

2 Connect the connector-

inlet supplied if necessary.

3 Insert the inlet hose

adapter into the water inlet of a washing machine and turn it to be fixed. .

4 Remove the tape, and

screw connector B into connector A tightly.

5 Connect the inlet hose to

the water tap adapter by pulling down the collar of the hose end.

6 Connect the inlet hose

adapter of the hose to the water inlet of the washing machine by turning it clockwise to be fixed tightly.

For Screw-Shaped Tap

• Please check the rubber packing inside the inlet hose adapter of the hose.

* Check the packing in the inlet

Connector B Connector A

Connector

Hose Connector

Rubber Packing

Connector

inlet

Connector

Hose Connector

Rubber Packing

TAPE

ELECTRICAL REQUIREMENTS

• Electrical earth is required on this washer.

• If it does not fit the outlet, have a proper outlet installed by a qualified electrician.

• Don’t earth to a gas pipe.

• Don’t change the power supply cord plug.

• Check with a qualified electrician if you are not sure the washer is properly earthed.

WARNING

Recommended earthing method

Electrical shock hazard : Failure to follow these instructions could result in

death or serious injury.

For your personal safety, this washer must be earthed. This washer is equipped with a power supply cord ‘A’ having a earthing plug ‘B’. To minimize possible shock hazard, the cord must be plugged into a mating earthing-type wall receptacle ‘C’. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have the proper earthed wall receptacle installed by a qualified electrician.

B A

Drain system

• Never forget to install drain hose before operating your washer.

• Open the packing box, and there is a drain hose inside the drum.

• Connect the drain hose to the drain outlet at the back side of the washer.

•

Top of laundry tub must be at least 60cm high and no higher than 100cm from bottom of washer.

• When installing the drain hose to tub(sink), secure it tightly with a string.

• Proper securing of the drain hose will protect the floor from damage due to water leakage.

• When the drain hose is too long, do not force it back into the washer. This will cause abnormal noise.

Level adjustment

1 If the washer is installed on an

unsuitable floor, it could make considerable noise, vibrate and cause a malfunction.

OPERATING YOUR W ASHER

2 Adjust the level of washer using adjustable legs.

• Please check if there is any gap between the

four adjustable legs and the floor.

• Adjust the level of washer by turning

adjustable legs. And make it sure that there is no swaying of washer.

• After the adjustment is finished, turn the fixing

nuts up tightly so that the washer maintains the adjustment.

3 Make it sure that the washer does not sway when you press

down the four corners of the washer’s top plate.

adjustable leg

Fixing Nut

NOTE

There should be no swaying of washer and all the adjustable legs should stick to the floor closely.

To obtain the best washing results, you must operate your washer properly. This section gives you this important information.

• Close zippers, snaps, and hooks to avoid

snagging other items. Remove pin, buckles, and other hard objects to avoid scratching the washer interior.

• Empty pockets and pull them inside out.

• Turn down cuffs and turn synthetic knits inside out to avoid pilling.

• Tie strings and sashes to avoid tangling.

• Treat spots and stains. (See ‘Removing stains’)

Preparing clothes for washing

• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together.

• Separate dark colors from light colors, colorfast items from non-colorfast item.

Soil (Heavy, Normal, Light) Separate clothes according to amount of soil. Color (White, Lights, Darks) Separate white clothes from colored clothes. Lint (Lint producers, Collectors) Wash lint producers and lint collectors separately.

Sorting

• Drop items into washer loosely. Items should move easily through wash water for best cleaning and wrinkle-free results.

• Load washer properly and select correct load size setting. Overloading and selecting a setting too small for the wash load can :

- Cause poor cleaning

- Increase wrinkling

- Create excessive lint

- Wear out items faster (because of pilling)

• Mix large and small items in each load. Load evenly to maintain washer balance. An unbalanced load can make the washer vibrate during spin.

• Reduce wash time when using a small load size setting. Load with only a few small items needs less wash time.

• Use a large load size setting to reduce wrinkling with permanent press clothes and some synthetic knits. These items should have more room to move in the water than heavy items. (towels, jeans)

1 Detergent case 2 Adding fabric softener

• If desired, add measured liquid fabric softener to the softener inlet.

• Pour liquid fabric softener into the dispenser using the amount recommended on the package.

• Do not exceed the maximum fill line. Overfilling can cause early dispensing of the fabric softener which could stain clothes.

• Do not open the detergent case when water is supplied.

• Avoid pouring fabric softener directly on the clothes.

Adding detergent

• Please use only the powder detergent for the front loader washing machine.

• Please use the proper amount of detergent in conformity with the instruction of the detergent manufacturer.

• A use of a large amount of detergent more than the recommended amount can cause many soapsuds and the overload to the motor. In addition to, this will deteriorate the washing and rinse performance.

Main wash

Pre wash

Fabric softener

+ 17 hidden pages

Daewoo DWD-FU107’S, DWD-FD147’S, DWD-FU127’S Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual