Daewoo DV6T822MX-ST1 User Manual

DVD-VIDEO PLAYER

OwnerÕs Manual

ODEL

: DV6T822MX-ST1

◆In the initial settings, exclusive channel for DVD/Video is set to CH 3.

Set the TV channel to CH3 before using it.

◆Region code of DVD/Video player for home is 4 or ALL. In inserting a

disc with other region code, it does not operate. Please only use a disc with region code 4 or ALL.

◆ is a ‘Prohibition’ mark. If this mark is displayed in operating the

product, please wait for a while, then use it. If " Prohibition" mark continues to be displayed in pressing a button after that, it means the button does not function in the currently played disc.

◆Press a product button on the remote control then use the product.

• DVD operation : [DVD] button

• Video operation : [VCR] button

Product Information

Important Safeguards

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance.

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

IMPORTANT FOR LASER PRODUCTS

• LASER : This Digital Video Disc Player employs a Laser System. To ensure proper use of this product please

read this owner’s manual carefully and retain for future reference. Should the unit require maintenance, contact an authorized service location - see service procedure.

Use of control adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.

To prevent direct exposure to the laser beam, do not try to open the enclosure. Visible laser radiation when open and interlocks defeated.

DO NOT STARE INTO THE BEAM.

• DANGER : Visible laser radiation when open and interlock failed or defeated.

Avoid direct exposure to beam.

• CAUTION : Do not open the top cover. There are no user serviceable parts

inside the Unit; leave all servicing to qualified service personnel.

CLASS 1 LASER PRODUCT

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception; which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experience radio/TV technical for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Any changes or modification in construction of this device which are not expressly approved by

the party responsible for compliance could void the user’s authority to operate the equipment.

Product Information

This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that can be repaired by the user.

1 Read Instructions

All the safety and operating instructions should be read before the unit is operated.

2 Retain Instructions

The safety and operating instructions should be retained for future reference.

3 Heed Warnings

All warnings on the unit and in the operating instructions should be adhered to.

4 FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5 Cleaning

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6 Attachments

Do not use attachments unless recommended by the unit’s manufacturer as they may cause hazards.

7 Water and Moisture

Do not use this unit near water- for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like. Caution : Maintain electrical safety. Powerline operated equipment or accessories connected to this unit should bear the UL listing mark or CSA certification mark on the accessory itself and should not be modified so as to defeat the safety features. This will help avoid any potential hazard from electrical shock or fire. If in doubt, contact qualified service personnel.

8 Accessories

Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury to a child or adult as well as serious damage to the unit. Use this unit only with a cart, stand , tripod, bracket, or table recommended by the manufacturer.

8A A unit and cart

combination should be moved with care. Quick stops, excessive force, and uneven

surfaces may cause the unit and cart combination to overturn.

9 Ventilation

Slots and openings in the case are provided for ventilation to ensure reliable operation of the unit and to protect it from overheating. These openings must not be blocked or covered. These openings must not be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat radiator. This unit should not be placed in a builtin installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

10 Power Sources

This unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions.

11 grounding or Polarization

This unit is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet.To prevent electric shock, do not use this polarized plug with an extension cord, receptacle, or other outlet unless the blades can be fully inserted without blade exposure. If you need an extension cord, use a polarized cord.

12 Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

13 Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National

PORTABLE CART WARNING

(symbol provided by RETAC)

Electrical Code, ANSI/NFPA No. 70-1984 (Section 54 of Canadian Electrical Code, Part 1) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See example as shown.

14 Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching or approaching such power lines or circuits as contact with them might be fatal. Installing an outdoor antenna can be hazardous and should be left to a professional antenna installer.

15 Lightning

For added protection for this unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

16 DISC TRAY

Keep your fingers well clear of the disc as it is closing. It may cause serious personal injury.

17 Overloading

Do not overload wall outlets of extension cords as this can result in a risk of fire or electric shock.

18 Object and Liquid Entry

Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or “short-out” parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit.

19 BURDEN

Do not place a heavy object on or step on the product. The object may fall, causing serious personal injury and serious damage to the product.

20 DISC

Do not use a cracked, deformed or repaired disc.

These discs are easily broken and may cause serious personal injury and product malfunction.

21 Servicing

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

22 Damage Requiring Service

Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions.

A. When the power-supply cord or plug is damaged. B. If liquid has been spilled, or objects have fallen

into the unit. C. If the unit has been exposed to rain or water. D. If the unit does not operate normally by

following the operating instructions. Adjust

only those controls that are covered by the

operating instructions. Improper adjustment of

other controls may result in damage and will

often require extensive work by a qualified

technician to restore the unit to its normal

operation. E. If the unit has been dropped or the cabinet has

been damaged.

F. When the unit exhibits a distinct change in

performance-this indicates a need for service.

23 Replacement Parts

When replacement parts are required, have the service technician verify that the replacements he uses have the same safety characteristics as the original parts. Use of replacements specified by the unit manufacturer can prevent fire, electric shock, or other hazards.

24 Safety Check

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks recommended by the manufacturer to determine that the unit is in safe operating condition.

25 Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

26 Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

ANTENNA LEAD IN WIRE

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250 PART H)

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

EXAMPLE OF ANTENNA GROUNDING

NEC - NATIONAL ELECTRICAL CODE

Important SafeguardsImportant Safeguards

Product Information

Advantages of This Product Are .....

• DVD, VCD, CD, CD-R(MP3), CD-RW, VHS playback function

• DVD one-touch record function

• Watching DVD for recording broadcast

• Integrated remote control (VCR, DVD)

• Ultra power savings : less than 3W for stand-by mode

• VISS function

• Multiplex sound playback/record

• High Sound Quality of 6 head Hi-Fi

• One Touch timer Recording (OTR)

• MP3 file playback function (CD-R disc having records of MP3 files)

• GUI (Graphical User Interface) OSD (On Screen Display)

By using the [DISPLAY] button on the remote control, information on the DVD/VCD/CD player and disc, can be displayed on the TV screen.

• Screensaver function (DVD)

• 3D sound (3D sound effect using 2 speakers)

• High bit / high sampling with 27MHz / 10bit video encoder

This unit has 27MHz / 10bit capability, that enables the faithful reproduction of fine images.

• High bit / high sampling with 96KHz / 24bit audio D/A converter

With this 96KHz / 24bit linear Pulse Code Modulated signals, which constitute the highest specifications in the DVD standards, you can enjoy faithfully reproduced sound in all of its various modes. To support 96KHz sampling / 24bit sound, the shaping noise of this multi-level digital sigma type of D/A converter is kept flat up to 44KHz, thus preventing the important audio signals from being affected.

• Coaxial, Optical digital output (PCM, Dolby Digital, dts)

You can enjoy high-level digital audio by connecting with amp embedded with Dolby Digital / dts decoder.

• Built-in Dolby Digital decoder (DVD)

• Analog audio 2-channels output for DOWNMIX (x1)

• Composite video out (x1)

• Slow Forward / Reverse (DVD) playback

• Fast Forward / Reverse playback

• Search of title, chapter, and time in DVD disc, and search of track and time in VCD and CD

• Various TV aspect (DVD)

4:3 for Pan and Scan, 4:3 for Letter Box, and 16:9 for Wide

• Repeat playback (title and chapter for DVD, track and disc for VCD/CD)

• Repeat a defined period from A to B (DVD)

• Selective Play (DVD/VCD/CD)

You can select and play the desired title / chapter of DVD and track of Video CD/CD in STOP mode.

• Various languages OSD (On Screen Display) function (DVD)

You can select and display OSD among various languages. (English, French, Spanish)

• Parental Lock function (DVD)

This function can prevent playback of software that may be unsuitable for children.

• Multi Audio function (DVD)

The audio soundtrack can be heard in up to 8 languages. In the case of SVCD or CVD, it depends on the disc. (The number of audio languages depends on the software.)

• Multi Subtitle function (DVD)

The subtitle can be seen in up to 32 languages. In the case of SVCD or CVD, it depends on the disc. (The number of subtitle languages depends on the software.)

• Multi Angle function (DVD)

This function allows you to choose the viewing angle of scenes which were shot from a number of different angles. (The number of angles depends on the software.)

• Screen zoom function (DVD/VCD)

Read Carefully before Using

Cautions in use of DVD-Video player are described below. Please read carefully before using a DVD-Video player.

Installation place and handling

• When you place this player near other devices, they may affect poorly together.

• When you place DVD-Video player and TV in the upper and lower sides, it may cause flickering of pictures or failure (tape is not ejected).

• When you place this player near strong magnetic materials, it may affect image or voice poorly or damage recording.

• Do not spill volatile liquids like insect spray over the player. Do not leave rubber or plastic products in contact with the player for a long time. They will cause deterioration or paint peel-off.

Not in use

• When the unit is not in use, be sure to remove the disc or tape and turn off the power.

• If you do not use the unit for a long period, remove batteries in remote control to prevent leakage.

• In case you don’t use the unit for a long time, the unit may not function properly in the future. Turn on and use the player occasionally.

Moving

• Repack the unit as it was originally packed at the factory. Alternatively, pack this product with towel not to be damaged.

• Eject any videotape.

Cleaning

• Dust off dirt in cabinet or control panel part smoothly with a soft cloth.

• For heavy dirt, soak the cloth in a weak detergent solution, wring it well and wipe. Use a dry cloth to wipe it out.

• Follow instructions in using chemical cleaners.

• Do not use any type of solvent such as gasoline or benzene, as they may cause deterioration or paint peel-off.

Checking

• Video is a high precision device. To obtain a clear screen, we recommend regular inspection and maintenance every 1,000 hours of use by technical engineers.

• For checking, contact your dealer or your nearest service center.

Checking and Replacement of Antenna

• Antenna is subject to change in its direction or damage by wind and rain. For clean screen, contact and consult your nearest service center about checking and replacement.

In recording important screen

• Be sure to record the screen and check whether recording is performed properly. We beg you to understand compensation of recording if recording is not performed by badness of used tape or video.

• Do not use your recordings without permission of a copyrighter except personal usage.

Tape and Disc Handling

• Do not use any tape and disc below. Damage of video head or cut/coiling of tape may cause failure.

- Tape with mold

- Tape or disc stained with juice or attachments

- Tape having breakage connection

- Disassembled tape

- Disc with severe scratch

• Moisture condensation may occur in tape. Moisture condensation damages the tape. Please use the tape after the moisture condensation is disappeared.

• After use, store tape vertically in a case to prevent loose.

• Do not store the following places.

- High temperature and humidity

- Subject generation of mold

- Subject to direct sunlight

- Much dirt or dust

- Near strong magnetic materials such as speaker

◆ Instructions in using remote control

• Operate remote control within 7m from the unit.

• Do not press 2(two) buttons at the same time.

• Do not light up sending part of remote control.

• Do not keep in the place with much dust and humidity.

Product Information

Identification of Controls

Front panel

!@ #$

& * )1 23^ (

456

Power (STANDBY/ON) button

Use to power the device on/off if AC power supply is connected.

Place to insert videotape

Eject button

Disc tray

Open/Close Tray button

Video input jack

Audio input jack

Copy button

Use to copy contents of disc into a videotape.

(

Record button

)

Channel Up/Down button

Operation Display Window

Display operation of device. For more information, see “Operation Display Window” in the next page.

Select button

Use to change DVD mode to VCR mode, and vice versa.

Stop button

Use to stop playing.

Rewind button

Use to rewind currently being played videotape or disc; or to playback back rapidly.

Playback/PAUSE button

Playback videotape or disc. Press this button to pause a screen.

Fast Forward button

Use to wind currently being played videotape or disc; or to playback rapidly.

Contents

Important Safeguards .................................... 1

Advantages of This Product Are .... ................. 4

Read Carefully before Using ............................ 5

Contents ...................................................... 6

Identification of Controls ............................... 7

Remote Control ............................................. 9

Connecting with TV....................................... 10

Connecting with Cable Box ...........................11

Connecting with Other Video Equipment ......... 12

Connecting with an Analog Audio .................. 13

Connecting with a dolby digital decoder or DTS

decoder....................................................... 14

Output Select .............................................. 15

Clock Set ................................................... 15

DVD Playback .............................................. 16

VCR Playback .............................................. 17

VCR Operation

Memorizing TV Channels .............................. 18

Recording ................................................... 20

Timer Recordings ....................................... 22

Watching and Recording Cable TV .................. 25

Using advanced features ............................... 26

Hi-Fi Stereo Playback ................................... 30

Basic Operation

Installation

Playing a desired scene ................................. 31

Confirming the current PLAY mode on screen .. 35 AUDIO language, SUBTITLE language

and 3D AUDIO.............................................. 36

ZOOM, Multi Angle and Digest play ................. 37

About MP3 discs .......................................... 38

Displaying menus in a disc. ........................... 39

LANGUAGE Setup .......................................... 30

VIDEO Setup................................................. 40

AUDIO Setup............................................... 40

Others Setup ............................................... 41

About DVD................................................... 42

Basic information about VCR and Videotape.... 44

Before doubting about troubles (DVD) ............ 45

Before doubting about troubles (VCR) ............. 46

Specifications ............................................. 48

Setup

DVD Operation

The others

Product Information

Operation Display Window

Time, Counter and Current Operation

Tray is opened Tray is closed Disc is loaded There is no disc in tray Disc has some error Menu screen is displayed Setup menu is displayed Power is ON Power is OFF

3D Sound Indicator

DVD Disc Operation

VCR Operation REC and TIMER REC display

Recording , TIMER Recording , To be Timer-recorded, To be Timer-recorded state ERROR (No Tape or Tape without tab)

Copying

Use to copy contents of disc into videotape.

AM dts Disc Indicator Track Chapter

This is displayed in DVD disc.

Product Information

Rear Panel

ANT.IN

RF OUT

OUT

AUDIO

VIDEO

COAXIAL

S-VIDEO OUT

DIGITAL AUDIO OUT

COMPONENT OUTAUDIO OUT

OPTICAL

^ *&$# %

Power Cord

It is a jack for supplying power to the unit. Connect to outlet in a wall.

Digital Output (OPTICAL, COAXIAL) Jack

To enjoy sound quality of theater level in home, connect one of these jacks with amp or unit embedded with digital audio decoder.

AUDIO Out Jack

COMPONENT Out Jack

To obtain better screen quality, connect the unit to TV or monitor with COMPONENT(480i) input.

S-Video Output Jack

A/V Output Jack

A/V Input Jack

Connection to Antenna Cable

(

Connection to TV

Identification of Controls

Remote Control

@ #

& * (

)

1 2 3 4

7 8

“

‘ + = Q q W w E

[DVD]

MENU button

@ POWER button #

[DVD]

TITLE /PBC button

[DVD]

OPEN/CLOSE button,

[VCR]

EJECT button

[DVD, VCR]

MOVE/SELECT in OSD,

[VCR]

Channel

Up/Down button

^ SETUP button &

[DVD]

REPEAT Playback button

[DVD]

REPEAT a defined period from A to B

button

(

[DVD]

PREVIOUS button (move into a previous

chapter or track)

) Reverse SEARCH in Play mode, Reverse SLOW in

Still mode

[DVD]

PROGRAM button

[DVD, VCR]

CLOCK/COUNTER button

[DVD, VCR]

TV/VCR button

[VCR]

Record button

[DVD, VCR]

NUMBER button ,

[VCR]

TRACKING -/+

button

6 VCR SELECT button 7 DVD SELECT button 8

[DVD, VCR]

OSD DISPLAY button

9 OUTPUT Selection button 0 ENTER button “ CLEAR/3D button ‘

[DVD, VCR]

AUDIO LANGUAGE Select,

[VCR]

AUDIO

Select button

[DVD]

SUBTITLE Select button

[DVD]

NEXT button (Move into a next chapter or

track) ,

[VCR]

Frame Advance button in pause

mode

Q PLAY/PAUSE button q Forward SEARCH in Play mode, SLOW in Still

mode

W STOP button w

[DVD]

Chapter/Title/Time SEARCH button

[DVD]

ZOOM button

[DVD]

ANGLE,

[VCD]

DIGEST,

[VCR]

Record SPEED

button

R TV output system select (NTSC, PAL-M, Auto)

button

Press the power [ ] button of the remote control for about 8 seconds. No buttons of front panel and remote control can be operated now and Lock indicator (“ ”) will be displayed on window display. To release child lock, press the power [ ] button of the remote control for about 8 seconds.

Child Lock!!!

Accessories

Remote Control 2 Batteries RF cable

Connecting cable to

Audio/Video jack

Owner’s Manual/

Warranty

• To purchase accessories or not supplied parts additionally, contact your nearest dealer or service center. But, owner’s manual and warranty are not sold additionally.

Installation

Various methods in connecting with TV

AUDIO

VIDEO

S-VIDEO

ANT INPUT

S-VIDEO INPUT

A/V INPUTCOMPONENT INPUT

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PRESONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

20181614 1210864 3

21191715 1311975 31

ANT.IN

RF OUT

OUT

AUDIO

VIDEO

COAXIAL

S-VIDEO OUT

DIGITAL AUDIO OUT

COMPONENT OUTAUDIO OUT

OPTICAL

Method

Remove circular cable (RF cable) (surplus cable) plugged in “ANT.IN” Jack in rear panel of TV. Connect the cable to “ANT.IN” jack in rear panel of DVD-Video. Connect TV to DVD-Video. Connect “RF OUT” jack in DVDVideo with “ANT.IN” jack in TV with RF cable.

Method

2 : Connecting to a TV that has a audio/video in jacks

Connect VIDEO OUT jack in DVD-Video to VIDEO IN jack in TV, and AUDIO OUT jack in DVD-Video to AUDIO IN jack in TV with connecting cable of Audio/Video jack. Select VCR mode by pressing TV/INPUT button in TV,

you can view more clear screen and sound than connection with RF cable only.

Method

3 : Connecting to a TV that has a component video in jacks

Use a component video cable (commercially available) in place of the yellow video cable to enjoy higher quality pictures. The component video connection only supplies video (picture) in the DVD mode of the DVD-Video. Therefore, in order to use the VCR features or view TV channels at the DVD-Video, you still need to either connect the RF coaxial cable between the ANT-OUT jack of the DVD-Video and the TV’s Antenna In jack, or connect the video cable.

Method

4 : Connecting to a TV that has a S-Video in jacks

Use a S-Video cable (not supplied) to enjoy higher quality pictures. Only in DVD mode, S-Video output is available.

■ In the initial SET, exclusive channel for video is set to CH 3. To change this setting, set again in “CHANNEL

SET” screen in VCR operation.

■ In connecting RF cable to TV, set TV channel to CH3.

Connecting with TV Connecting with Cable Box

How to connect

INPUT 1

OUT

ANT IN

INPUT 2

OUT

If your cable system only requires you to use a converter box for some channels

(i.e., pay-TV channels), follow these steps: Find the primary incoming RF cable. Plug this cable into a splitter (available at your local electronics store.)

■ You should install a distributor additionally.

How to watch general broadcasting with recording CATV

1 Set Channel Select switch of Converter Box to CH 3 or 4 as same as video exclusive channel. Press [SET]

button in [VCR] operation to set video exclusive channel in “CHANNEL SET” screen.

2 Press channel button of Converter Box to select channel to be recorded. In this case, if you want to watch

CATV to be recorded, press [TV/INPUT] button of TV to select “Out (VCR)”.

3 Press [REC] button in DVD-Video.

4 To watch general broadcasting, press channel button in TV to select the desired channel.

Connect one RF cable between one OUT terminal on the splitter and the IN terminal on the converter box. Connect another RF cable between the other OUT terminal on the splitter and the A-IN terminal on an A/B

switch (available at your local electronics store.) Connect a third RF cable between the OUT terminal on the converter box and the B-IN terminal on the A/B switch.

Connect a RF cable between the OUT terminal on the A/B switch and the ANT. IN on your DVD-VIDEO. When the A/B switch is in the B position, use the converter box to change channels ; when the A/B switch is in

the A position, use the DVD-VIDEO to change channels.

• VHF: 2 ~13 channels of TV , UHF: 14~69 channels of TV, CATV: Broadcasting is transmitted with cable from

broadcasting station by contract with the station and consumers. It does not need any antenna.

• In/Out jack in Audio/Video terminal: - In: A jack used to receive signal required in this unit from other units. Out: A jack used to send signal of this unit to other units.

• Connect with Audio/Video terminal, you can enjoy more clear video and audio. (Use OUTPUT button in this remote control to select video mode.)

• If screen is broken in connecting COMPONENT Out to Pr, Pb, Y of TV COMPONENT In jack , connect to Cr, Cb, Y.

• For some types of TV, you should press [TV/INPUT] button in TV remote control and convert from Out 1( VCR 1) or Out 2(VCR 2) mode to Broadcasting Channel mode to change TV channel.

• Change channel selection of CATV receiver in recording, contents of recording is changed.

Method 1

Method 2

RF Cable

AUDIO/VIDEO Cable

RF Cable

RF Cable

Method 3

Method 4

ANT.IN

RF OUT

OUT

AUDIO

VIDEO

Installation

Connecting with Other Video Equipment

How to Connect

AUDIO

VIDEO

ANT INPUT

A/V OUTPUT

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PRESONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

201816141210 8643

211917151311 97531

ANT.IN

RF OUT

OUT

AUDIO

VIDEO

COAXIAL

S-VIDEO OUT

DIGITAL AUDIO OUT

COMPONENT OUTAUDIO OUT

OPTICAL

How to Copy(Edit) Tape with Other Video Equipment

1 Connect Audio/Video Out jack in other video equipment to Audio/Video In jack in rear panel (or front

panel) of DVD-Video with connecting cable.

2 Connect “ANT. IN” jack in TV to “RF.OUT” jack in DVD-Video with RF cable.

3 To record contents of other video equipment with DVD-Video, insert recording tape attached recording tab

in DVD-Video.

1 Turn on DVD-Video.

2 Press [OUTPUT] button of remote control and adjust DVD-Video to display “External Input 1” or “External

Input 2” in TV screen.

3 Press [PLAY] button in other video equipment.

4 Press [REC] button in DVD-Video if you want to record contents of other video equipment.

5 Press [Pause] button in DVD-Video when unnecessary or undesired scene is displayed in recording.

(Caution) Recording is released automatically after 5 minutes since pressing [PAUSE] button.

Press [REC] button if you want to record again.

Playback VCR,

Camcorder,

Satellite

Receiver ...

... ...

RF Cable

AUDIO/VIDEO Cable

■ You can connect a wide variety of audio/video equipment to your DVD-Video, including : an additional VCR,

Laser Disc Player, DVD Player, Camcorder, Satellite Receiver, Video Game. Since all of these devices use essentially the same connections, they will be described together.

How to Connect

Connecting with an Analog Audio

AUDIO

ANT INPUT

AUDIO INPUT

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PRESONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

201816141210 8643

211917151311 97531

S-VIDEO

S-VIDEO INPUT

ANT.IN

RF OUT

OUT

AUDIO

VIDEO

COAXIAL

S-VIDEO OUT

DIGITAL AUDIO OUT

COMPONENT OUTAUDIO OUT

OPTICAL

1 Connect Audio jack. Connect AUDIO OUT in rear panel of DVD-Video to In jack of stereo sound unit.

2 For Input Select in stereo unit, Select “External Input” connected with DVD-Video.

3 Playback DVD disc or Hi-Fi videotape, you can hear sound in speaker of stereo unit.

+ 18 hidden pages