Daewoo DTQ-29U1SC-SSP, DTQ-29U5SC-SSP User Manual
http : //svc.dwe.co.kr
Caution
: In this Manual, some parts can be changed for improving. their
performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List)in
Service Information Center(http://svc.dwe.co.kr)
DAEWOO ELECTRONICS Corp.
Service Manual
S/M No : TCN794NEF0-R1
COLOR TELEVISION
CHASSIS : CN-794N
Model : DTQ-29U1SC/SSP
DTQ-29U5SC/SSP
DTQ-29U1SC DTQ-29U1SC
June. 2003
-1-
SAFETY PRECAUTIONS 2
SPECIFICATIONS 5
CIRCUIT BLOCK DIAGRAM 6
ALIGNMENT INSTRUCTIONS 7
YOUR REMOTE CONTROL 7
SERVICE MODE ADJUSTMENT 8
ASSEMBLY ADJUSTMENT 10
SCHEMATIC DIAGRAM 13
ELECTRICAL PARTS LIST 17
DIFFERENT PARTS LIST 36
EXPLODE VIEW 37
PRINTED CIRCUIT BOARD 39
IC DESCRIPTION 49
WAVEFORMS 55
TROUBLE SHOOTING GUIDE 58
NO POWER 58
NO PICTURE 59
NO SOUND 60
CH DON T STOP 61
NO COLOR
62
NO VERTICAL DEFLECTION
62
NO ON-SCREEN DISPLAY 63
NO REMOCON RECEIPT 63
TABLE OF CONTENTS
APPENDIX(Appendix is provide only by internet[http://svc.dwe.co.kr])
-2-
SAFETY PRECAUTIONS
CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY.
NEVER PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFACTURER’S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLY VOID
THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR ANT RESULTING PROPERTY DAMAGE OR USER INJURY.
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY CHECKS AND
SERVICING GUIDELINES. TO DO OTHERWISE, INCREASES THE RISK OF
POTENTIAL HAZARDS AND INJURY TO THE USER.
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTECTION
FROM A.C. LINE SHOCK.
SAFETY CHECKS
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED, A CHECK
SHOULD BE MADE OF THE FOLLOWING:
SUBJECT:FIRE & SHOCK HAZARD
1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAY AS
TO AVOID POSSIBILITY OF ADJACENT COMPONENT SHORTS. THIS IS
ESPECIALLY IMPORTANT ON THOSE MODULES WHICH ARE TRANSPORTED TO AND FROM THE REPAIR SHOP.
2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICES SUCH AS
INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN RELIEFS, POWER
SUPPLY CORDS, AND OTHER HARDWARE HAVE BEEN REINSTALLED PER
ORIGINAL DESIGN. BE SURE, THAT THE SAFETY PURPOSE OF THE
POLARIZED LINE PLUG HAS NOT BEEN DEFEATED.
3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLD SOLDER JOINTS, SOLDER SPLASHES OF SHARP SOLDER POINTS. BE CERTAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES.
4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR DETERIORATION TO
PARTS AND COMPONENTS, FOR FRAYED LEADS, DAMAGED INSULATION
(INCLUDING A.C. CORD), AND REPLACE IF NECESSARY. FOLLOW ORIGINAL LAYOUT, LEAD LENGTH AND DRESS.
5. NO LEAD OR COMPONENT SHOULD TOUCH A RECEIVING TUBE OR A
RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUND PROTRUDING METAL SURFACES MUST BE AVOIDED.
6. ALL CRITICAL COMPONENTS SUCH AS FUSES, FLAMEPROOF RESISTOR,
CAPACITORS, ETC. MUST BE REPLACED WITH EXACT FACTORY TYPES.
DO NOT USE REPLACEMENT COMPONENTS OTHER THAN THOSE SPECIFIED OR MAKE UNRECOMMENDED CIRCUIT MODIFICATIONS.
7. AFTER RE-ASSEMBLY OF THE STE ALWAYS PERFORM AN A.C. LEAKAGE
TEST ON ALL EXPOSED METALLIC PARTS OF THE CABINET. (THE CHANNEL SELECTOR KNOB, ANTENNA TERMINALS, HANDLE AND SCREWS) TO
BE SURE THE SET IS SAFE TO OPERATE WITHOUT DANGER OF ELECTRICAL SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER DURING THIS
TEST USE AN A.C. VOLTMETER, HAVING 5000 OHMS PER VOLT OR MORE
SENSITIVITY, IN THE FOLLOWING MANNER : CONNECT A 1500 OHM 10
WATT RESISTOR, PARALLELED BY A .15 MFD. 150V A.C. TYPE CAPACITOR BETWEEN A KNOWN GOOD EARTH GROUND (WATER POPE, CONDUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME.
MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500 OHM
RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUG AND
REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED METALLIC
PART. VOLTAGE MEASURED MUST NOT EXCEED .75 VOLTS R.M.S THIS
CORRESPONDS TO 0.5 MILLIAMP A.C. NAY VALUE EXCEEDING THIS LIMIT
CONSTITUTES A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED
IMMEDIATELY.
SUBJECT : X-RADIATION
1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PERSONNEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTENTIAL
SOURCE OF X-RAYS IN CURRENT T.V. RECEIVERS IS THE PICTURE TUBE.
HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHEN THE HIGH VOLTAGE IS AT THE FACTORY SPECIFIED LEVEL. THE PROPER VALUE IS GIVEN
IN THE APPLICABLE SCHEMATIC. OPERATION AT HIGHER VOLT-AGES MAY
CAUSE A FAILURE OF THE PICTURE TUBE OR HIGH VOLTAGE SUPPLY
AND UNDER CERTAIN CIRCUMSTANCES, AMY PRODUCE RADIA-TION IN
EXCESS OF DESIRABLE LEVELS.
2. ONLY FACTORY SPECIFIED C.R.T ANODE CONNECTORS MUST BE
USED.DEGAUSSING SHIELDS ALSO SERVE AS X-RAY SHIELD IN COLOR
SETS. ALWAYS RE-INSTALL THEM.
3. IT IS ESSENTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN ACCURATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRATION OF THE
METER SHOULD BE CHECKED PERIODICALLY AGAINST A REFERENCE
STANDARD. SUCH AS THE ONE AVAILABLE AT YOUR DISTRIBUTOR.
4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY THERE
IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY TIME A COLOR
CHASSIS IS SERVICED, THE BRIGHTNESS SHOULD BE RUN UP AND DOWN
WHILE MONITORING THE HIGH VOLTAGE WITH A METER TO BE CERTAIN
THAT THE HIGH VOLTAGE DOES NOT EXCEED THE SPECIFIED VALUE AND
THAT IT IS REGULATING CORRECTLY. WE SUGGEST THAT YOU AND YOUR
SERVICE ORGANIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE
REGULATION IS ALWAYS CHECKED AS A STANDARD SERVICING
PROCEDURE, AND THAT THE HIGH VOLTAGE READING BE RECORDED ON
EACH CUSTOMER S INVOICE.
5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN A
PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE, AVOID BEING
UNNECESSARILY CLOSE TO THE PICTURE TUBE AND THE HIGH VOLTAGE
SUPPLY. DO NOT OPERATE THE PRODUCT LONGER THAN IS NECESSARY
TO LOCATE THE CAUSE OF EXCESSIVE VOLTAGE.
6. REFER TO HV, B+ AND SHUTDOWN ADJUSTMENT PROCEDURES
DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS (WHERE
USED).
SUBJECT : IMPLOSION
1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTEGRA
IMPLOSION PROTECTION SYSTEM. BUT CARE SHOULD BE TAKEN TO
AVOID DAMAGE DURING INSTALLATION. AVOID SCRATCHING THE TUBE.
OF SCRATCHED REPLACE IT.
2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.
SUBJECT : TIPS ON PROPER INSTALLATION
1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBYHOLE OR
CLOSELY FITTING SHELF SPACE, OVER OR CLOSE TO HEAT DUCT, OR IN
THE PATH OF HEATED AIR FLOW.
2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO
INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS
WHERE STEAM LEAKAGE IS A FACTOR, ETC.
3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT REAR VENTING.
THE CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE
SCARVES OR OTHER COVERINGS WHICH MIGHT OBSTRUCT VENTILATION.
4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCIAL
MOUNTING KIT, MUST FOLLOW THE FACTORY APPROVED MOUNTING
INSTRUCTIONS. A PRODUCT MOUNTED TO A SHELF OR PLATFORM MUST
RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN SPACERS)TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM, BOLTS OR
SCREWS USED FOR FASTENERS MUST NOT TOUCH ANY PARTS OR
WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS.
5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON
SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS
PROPERLY SECURED.
6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS MOUNTING TO THE CART. CAUTION THE CUSTOMER ON THE HAZARDS OF TRYING TO ROLL A CART WITH SMALL CASTERS ACROSS THRESHOLDS OR
DEEP PILE CARPETS.
7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND WHICH
HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES. INC. FOR
USE WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR
GENERICALLY APPROVED FOR USE WITH T.V.S OF THE SAME OR LARGER
SCREEN SIZE.
8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS,
EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SINGLE
OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TO HOME AND
FAMILY.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO
ALERT THE SERVICE PERSONNEL TO THE PRES-ENCE
OF UNINSULATED DANGEROUS VOLTAGE
THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL
TRIANGLE IS INTENDED TO ALERT THE SERVICE
PERSONNEL TO THE PRESENCE OF IMPORTANT
SAFETY INFORMATION ON SERVICE LITERATURE.
SUBJECT : GRAPHIC SYMBOLS
10WATT
GOOD EARTH GROUND
SUCH AS THE WATER
PIPE, CONDUIT, ETC.
1500 OHM
A.C. VOLTMETER
PLACE THIS PROBE
ON EACH EXPOSED
METAL PART
0.15 uF
-3-
SAFETY PRECAUTIONS
CAUTION : Do not attempt to modify this product in any way. Unauthorized modifications will not only void the warranty, but may lead to your
being liable for any resulting property damage or user injury.
Service work should be performed only after you are thoroughly familiar
with all of the following safety checks and servicing guide-lines. To do
otherwise, increases the risk of potential hazards and injury to the user.
SAFETY CHECKS
After the original service problem has been corrected, a check should be
made of the following:
SUBJECT : FIRE & SHOCK HAZARD
1. Be sure that all components are positioned in such a way as to avoid
possibility of adjacent component shorts. This is especially important on
those chassis which are transported to and from the repair shop.
2. Never release a repair unless all protective devices such as insula-tors,
barriers, covers, shields, strain reliefs, and other hardware have been
reinstalled per original design.
3. Soldering must be inspected to discover possible cold solder joints,
frayed leads, damaged insulation (including A.C. cord), solder splashes
or sharp solder points. Be certain to remove all loose for-eign particals.
4. Check for physical evidence of damage or deterioration to parts and
components, and replace if necessary follow original layout, lead length
and dress.
5. No leads or components should touch a receiving tube or a resistor
rated at 1 watt or more. Lead tension around protruding metal sur-faces
must be avoided.
6. All critical components such as fuses, flameproof resistors, capaci-tors,
etc. must be replaced with exact factory types. Do not use replacement
components other than those specified or make unrecommended circuit
modifications.
7. After re-assembly of the set always perform an A.C. leakage test on all
exposed metallic parts of the cabinet, (the channel selector knob,
antenna terminals, handle and screws) to be sure the set is safe to
operate without danger of electrical shock. Do not use a line isolation
transformer during this test. Use an A.C. voltmeter, having 5000 ohms
per volt or more sensitivity, in the following manner : connect a 1500
ohm 10 watt resistor, paralleled by a 15 mfd. 150V A.C. type capacitor
between a known good earth ground (9water pipe, conduit, etc.) and
the exposed metallic parts, one at a time. Measure the A.C. voltage
across the combination of 1500 ohm resistor and 0.15 MFD capacitor.
Reverse the A.C. plug and repeat A.C. voltage measurements for each
exposed metallic part. Voltage measured must not exceed 0.75 volts
R.M.S. This corresponds to 0.5 milliamp A.C. Any value exceeding this
limit constitutes a potential shock hazard and must be corrected immediately.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the service personnel to the presence of uninsulated dangerous voltage that may be of sufficienty magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the service personnel
to the presence of important safety information
in service literature.
Fuse symbol is printed on pcb adjacent to the
fuse, with RISK OF FIRE REPLACE FUSE AS
MARKED . The symbol is explained in the service manual with the following wording or equivalent.
CAUTION : FOR CONTINUED PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH SAME TYPE (4A, 125V) and
ATTENTION: AFIN D ASSU UNE PROTECTION PERMANENTE
CONTRE LES RISQUES D INCENDIE, REMPLACER UNIQUE-MENT
PAR UN FUSIBLE DE MEME TYPE ET DE 4A, 125V .
SUBJECT : X-RADIATION
1. Be sure procedures and instructions to all service personnel cover
the subject of X-rays in current T.V. receivers is the picture tube.
However, this tube does not emit X-rays when the high voltage is at
the factory specified level. The proper value is given in the applicable schematic. Operation at higher voltages may cause a failure
of the picture tube or high voltage supply and, under certain circumstances, may produce radiation in excess of desirable levels.
2. Only factory specified C.R.T. anode connectors must be used.
Degaussing shields also serve as X-ray shield in color sets. Always
re-install them.
3. It is essential that the serviceman has available an accurate and
reliable high voltage meter. The calibration of the meter should be
checked perio - dically against a reference standard. Such as the
one available at your distributor.
4. When the high voltage circuitry is operating properly there is no
possibility of an X-radiation problem. Every time a color chassis is
serviced, the brightness should be run up and down while monitoring the high voltage with a meter to be certain that the high voltage
does not exceed the specified value and that it is regulating correctly. We suggest that you and your service organization review
test procedures so that voltage regulation is always checked as a
standard servicing procedure. And that the high voltage reading be
recorded on each customer s invoice.
5. When troubleshooting and making test measurements in a receiver
with a problem of excessive high voltage, avoid being unnecessarily
close to the picture tub eand the high voltage compartment. Do not
operate the chassis longer than is necessary to locate the cause of
excessive voltage.
6. Refer to HV, B+and Shutdown adjustment procedures described in
the appropriate schematic and diagrams(where used).
10WATT
GOOD EARTH GROUND
SUCH AS THE WATER
PIPE, CONDUIT, ETC.
1500 OHM
A.C. VOLTMETER
PLACE THIS PROBE
ON EACH EXPOSED
METAL PART
0.15 uF
-4-
SAFETY PRECAUTIONS
SUBJECT : IMPLOSION
1. All direct viewed picture tubes are equipped with an integral implosion protection system, but care should be taken to avoid damage
during installation. Avoid scratching the tube. If scratched, replace
it.
2. Use only recommended factory replacement tubes.
SUBJECT : TIPS ON PROPER INSTALLATION
1. Never install any receiver in closed-in recess, cubbyhole or closely
fitting shelf space over, or close to heat duct, or in the path of
heated air flow.
2. Avoid conditions of high humidity such as : Outdoor patio installations where dew is a factor. Near steam radiators where steam
leakage is a factor, etc.
3. Avoid placement where draperies may obstruct rear venting. The
customer should also avoid the use of decorative scarves or other
coverings which might obstruct ventilation.
4. Wall and shelf mounted installations using a commercial mounting
kit, must follow the factory approved mounting instructions. A
receiver mounted to a shelf or platform must retain its original
feet(or the equivalent thickness in spacers) to provide adequate are
flow across the bottom, bolts or screws used for fasteners must not
touch and parts or wiring. Perform leakage test on cus-tomized
installations.
5. Caution customers against the mounting of a receiver on sloping
shelf or a tilted position, unless the receiver is properly secured.
6. A receiver on a roll-about cart should be stable on its mounting to
the cart. Caution the customer on the hazards of trying to roll a cart
with small casters across thresholds or deep pile carpets.
7. Caution customers against the use of a cart or stand which has not
been listed by underwriters laboratories, inc. For use with their
specific model of television receiver or generically approved for use
with T.V. s of the same or larger screen size.
-5-
SPECIFICTION
Model
DTQ-29U1/U5SC DTQ-29U1/U5SSP
Item
CHASSIS CN-794N
TV Standard NTSC-M
Power Input AC 120v, 60Hz
Power Consumption 112W
Tuning System Frequency Synthesizer(FS) Tuning System
Tuning Ranges TV VHF(L) : CH2 - CH6
UHF(H) : CH7 - CH13
UHF : CH14 - CH69
CATV VHF(L) : 5A, A,B,A-5-A-1
CH2-CH6
VHF(H) : C-W+11
CH7 - CH13
UHF : W+12-W+84
Sound Output 5W + 5W 7W + 7W
Speaker 8 ohm 7W x 2EA 8 ohm 15W x 2EA
Antenna Input Impedance 75 ohm Unbalanced
Auxiliary Input Terminal Side : Video, Audio(L,R) - AV2
Rear : Video, Audio(L,R) - AV1
S-Video
Y, Cb, Cr, Audio(L,R) - CVI
Auxiliary Output Terminal Rear : Video, Audio(L,R) - MONITOR OUT
Intermediate Frequencies Picture IF Carrier Frequency : 45.75MHz
Sound IF Carrier Frequency : 41.25MHz
Color Sub-Carrier Frequency : 3.579545MHz
Remote Control R-43A07
Special Function 1) Closed Caption
2) V-Chip
3) Channel Label
-6-
CIRCUIT BLOCK DIAGRAM
-7-
ALIGNMENT INSTRUCTION
1. POWER
use this button to turn your TV on or off.
2. MUTE
Use to turn the TV's sound on and off.
3. CH
Use these buttons to change your TV's volume, to
activate selections in the menu system.
4. VOL
Use thesebuttons to change your TV's volume, to
activate selections in the meny system, or to change
audio and video settings.
5. MENU
Use this button to turn the TV's menu system on and off.
6. DISPLAY
Use this button to display the channel numbeer and
status.
7. INPUT
Use this button to select the TV's signal source.
8. VIDEO
Use this button to display video adjustment.
9. 0-9
Use these buttons to change channels.
10. SLEEP
Use this button to program the TV to turn off after a
certain time.
11. PREVIOUS
Use this button to return to the previous channel you
were watching.
1
3
4
11
8
7
2
4
5
3
9
10
6
POWERMUTE
MENU
CH
SLEEP PREVIOUS
VIDE OINPU TDISPLAY
1 2 3
4 5 6
7 8
0
9
VOL VOL
Your Remote Control(R-43A07)
-8-
ALIGNMENT INSTRUCTION
1. SERVICE MODE ADJUSTMENTS
Follow the steps below whenever service adjustment is required. See Table- A and Table- B to determine if
service adjustments are required.
1) How to enter the service mode using the user remote control.
•
Turn the set on.
•
Direct the remote control to the reception window of TV.
•
Push buttons of remote control in sequence as follows.
1 MUTE
DISPLAY MUTE
•
Then, the screen will appear as follows.
•
Using the channel up or channel down button, select the item you wish to adjust.
(The color of selected item turns into the red.)
•
Press the volume up or down button to enter in the service mode you wish to adjust.
2) How to memorize the adjusted values in the service mode.
•
Must press
DISPLAY
button the state which the screen is displaying each of service
menus
after all adjustments are completed each of all service menu.
Table-A : Adjust the values of service mode when a part is replaced.
PART
REPLACED
ADJUSTMENT
NOTES
NECESSARY UNNECESSARY
I701
(U-COM)
O
Data is stored in I703.
I101
(MAIN)
O
I703
(EEPROM)
Initial setting values are written from I701.
ADJUSTING ITEMS
S5 : SOUND CONTROL
O S6 : H.PHASE/H.SIZE/V.POSI/V.SIZE
S8 : RD/GD/BD/RB/GB/BB
S9 Subbrightness
CRT O Adjust items related to picture tube only.(White Balance adjustment)
S2 SCRN
S5 SND
S6 GEO
VDP
S7
S8 W/B
S9 DP
S12 FACT
-9-
ALIGNMENT INSTRUCTION
MODE ADJUSTMENT DATA REMARKS
OEC LG RANGE
S2 Screen Adjustment
S5 SOUND CONTROL
FM/AM PRE 65(SSP:75) 0~127
SCART PRE 65(SSP:70) 0~127
MONI VOL 32(SSP:20) 0~127
QUASI CHECK NO YES/NO
NO SD NO POWER NO YES/NO
S6 V-SIZE 399 379 0~510
V-POSI 1104 1168 240~1712
H-PHASE 41 36 0~255
H-SIZE 1156 1060 4~4092
V-LIN 271 269 0~511
V-S 237 2~512
HBST 20 0~511
TILT 504 8~1016
P-PARA 549 3~1021
H-SYM 984 8~2040
H-COR 984 8~2040
HBSO 6 0~511
S7 BCLTH 185 0~2047
BCLTM 5 0~15
BCLG 5 0~15
BCLTST 0 0~1020
PKINV 0 0/1
BLE 0 0/1
BTLT 2 0~15
BAM 20 0~31
SVG1 20 0~63
SVD1 1 0~7
SVLIM 30 0~127
SVDEL 7 0~15
OSDBR 255 0~511
OSDCO 120 0~511
S8-1 RD 700 0~1023
GD 700 0~1023
BD 700 0~1023
RB 350 0~511
GB 350 0~511
BB 350 0~511
S8-2 SCR R-BIAS 0 0~511
SCR G-BIAS 0 0~511
SCR B-BIAS 420 0~511
SCR R-DRIVE 0 0~1023
SCR G-DRIVE 0 0~1023
SCR B-DRIVE 200 0~1023
S9 DP-BRI 145 0~310
DP-CONT 13 0~13
DP-TINT 170 0~222
DP-COL 200 0~850
DP-OVPK 4 0~4
DP-UNPK 2 0~4
BRI-SET 75 0~100
S11 DVCO OK
S12 Forwarding Mode Factory initialization
Table-B
-10-
ALIGNMENT INSTRUCTION
2) FOCUS ADJUSTMENT
•
Turn in a local station and adjust the Focus Control knob (located on FBT) for best picture
details at high light condition.
3) GEOMETRIC ADJUSTMENTS (S6)
•
Select service adjustment S6
•
You can see the OSD as shown in below.
3-1. Horizontal Position Adjustment
•
Select H-PHASE item, adjust H-PHASE data value to obtain proper horizontal centering of the
internal cross pattern at the left and right of the screen.
3-2. Vertical Position Adjustment
•
Select V-POSI item, adjust V-POSI data value to center the raster properly on the screen.
2. ASSEMBLY ADJUSTMENTS
1) SCREEN ADJUSTMENT (S2)
•
Enter the service mode and select service adjustment S2.
•
You can see the one horizontal line on the screen.
•
Adjust the Screen Control Volume (located on FBT) so that the horizontal line onscreen may be
disappeared.
•
Press the volume up or down button to exit in the screen adjustment mode.
IN THE SCREEN ADJUSTMENT MODE, DONT PRESS OTHER BUTTONS EXCEPT VOLUME UP OR DOWN BUTTON.
CAUTION
V-SIZE
V-POSI
H-PHASE
H-SIZE
V-LIN
V-S
HBST
TILT
P-PARA
H-SYM
H-COR
HBSO
504
549
984
984
358
379
1168
36
1060
269
237
260
-11-
ALIGNMENT INSTRUCTION
3-3. Vertical Size Adjustment
•
Select “V.SIZE” item, adjust “V.SIZE” data value to proper vertical size as follows.
4) WHITE BALANCE ADJUSTMENT(S8)
•
Receive a good local channel.
•
Enter the service mode and select service adjustment S8.
•
You can see the OSD as shown in below.
•
Using volume up or volume down, adjust service adjustment data of RD/GD/BD and RB/GB/BB until a good gray
scale with normal whites is obtained.ALIGNMENT INSTRUCTIONS
•
Press the DISPLAY button to memorize the data.
5) DIGITAL PRESET(D.P) ADJUSTMENTS(S9)
SUBBRIGHTNESS ADJUSTMENT
•
Receive a good local channel.
•
Enter the service mode and select service adjustment S9.
•
You can see the OSD as shown in below.
RD 700
GD 700
BD 700
RB 350
GB 350
BB 350
MOVE ADJUST RECALL : SET
DP-BRI 145
DP-CONT 8
DP-TINT 170
DP-COL 0
DP-OVPK 4
DP-UNPK 2
BRI-SET 75
MOVE ADJUST RECALL : SET
-12-
ALIGNMENT INSTRUCTION
•
Select Subbrightness item, adjust Subbrightness data value
to obtain normal
brightness level.
•
Press the DISPLAY button to memorize the data.
CONTRAST
•
Fixed value = 8
TINT
•
Fixed value = 170
COLOR
•
Fixed value = 0
6) FACTORY OUTGOING MODE (S12 : FACT)
•
If you select the S12, then the set becomes factory outgoing status.
•
You can see the OSD “outgoing OK”
-14-
ELECTRICAL PARTS LIST
1 ZZ100 48B4343A07 TRANSMITTER REMOCON R-43A07 (AA)
2 ZZ110 PTACPWJ954 ACCESSORY AS DTQ-21U4SC
3 M821 4858213801 BAG INSTRUCTION L.D.P.E T0.05X250X400
4 ZZ120 PTBCSHK016 COVER BACK AS DTQ-29U1SC
5 M211 4852163100 COVER BACK FR HIPS GY 29U1
6 M781 4857817630 CLOTH BLACK FELT 400X20X0.7
7 M782 4857817612 CLOTH BLACK FELT 250X20X0.7
8 ZZ130 PTPKCPK016 PACKING AS DTQ-29U1SC
9 10 6520010100 STAPLE PIN AUTO W65
10 M681 4856812400 BAND PP AUTO T1.1XW17mmXL770M
11 M801 4858057600 BOX CARTON DW-3
12 M811 4858101100 PAD EPS 29U1
13 M821 4858215601 BAG P.E PE FOAM t0.5x1600x1270
14 ZZ131 48519A4210 CRT GROUND NET 2901H-1015-2P
15 ZZ132 58G0000143 COIL DEGAUSSING DC-29S1
16 ZZ140 PTCACAK016 CABINET AS DTQ-29U1SC
17 M111A 7172401612 SCREW TAPPTITE TT2 TRS 4X16 MFZN BK
18 M201A 4856015821 SCREW CRT FIX SWRM+SK5 L=35
19 M201C 4856215404 WASHER RUBBER CR T4.0
20 M201E 4856816300 CLAMP WIRE NYLON 6 (V0)
21 M211A 7172401612 SCREW TAPPTITE TT2 TRS 4X16 MFZN BK
22 M211B 7172401612 SCREW TAPPTITE TT2 TRS 4X16 MFZN BK
23 M221C 7178301212 SCREW TAPPTITE TT2 WAS 3X12 MFZN BK
24 M541 4855415800 SPEC PLATE 150ART P/E FILM (C/TV)
25 M686 4856812001 TIE CABLE NYLON66 DA100
26 SP01A 7172401212 SCREW TAPPTITE TT2 TRS 4X12 MFZNBK
27 SP01B 7172401212 SCREW TAPPTITE TT2 TRS 4X12 MFZNBK
28 V901 4859639260 CRT A68QCU757X81 P38
29 ZZ200 PTFMSJK016 MASK FRONT AS DTQ-29U1SC
30 M191 4851948400 BUTTON CTRL 4955100+5549200 29U1
31 M191A 7178301011 SCREW TAPPTITE TT2 WAS 3X10 MFZN
32 M201 4852083500 MASK FRONT FR HIPS GY 29U1
33 M481 4854864100 BUTTON POWER FR HIPS GY 29U1
34 M481A 4856716000 SPRING SWPA PIE0.5
35 M561 4855617400 MARK BRAND CU AU+ABS BK
36 ZZ201 PTSPPWK016 SPEAKER AS DTQ-29U1SC
37 P601A 4850704S32 CONNECTOR YH025-04+YRT205+ULW900500
38 SP01 4858310810 SPEAKER SP-58126F01
39 SP02 4858310810 SPEAKER SP-58126F01
40 ZZ204 PTJASWJ811 PCB JACK AS DTQ-29M2
NO LOC PARTS CODE PARTS NAME PARTS DESCRIPTION REMARK
**This BOM is based on DTQ-29U1SC
Caution
: In this Manual, some parts can be changed for improving. their performance without notice in the parts list. So, if
you need the latest parts information, please refer to PPL(Parts Price List)in Service Information
Center(http://svc.dwe.co.kr)
-15-
ELECTRICAL PARTS LIST
41 10 2193102005 SOLDER BAR SN:PB=63:47 S63S-1320
42 JA02 4859105450 JACK PIN BOARD YSC03P-4120-9S
43 M112 4851114003 PANEL AV ASSY 2326802+5934301
44 M112A 7178301011 SCREW TAPPTITE TT2 WAS 3X10 MFZN
45 M684 4856812001 TIE CABLE NYLON66 DA100
46 P201A 4850705S04 CONNECTOR YH025-05+YBNH250+ULW=400
47 ZZ200 PTJAJAJ811 PCB JACK AXIAL AS DTQ-29M2
48 A001 4859802917 PCB JACK 79.05X27.3(197X246/14)C1B
49 CC608 CCZB1H102K C CERA 50V B 1000PF K (AXIAL)
50 CCS07 CCZB1H102K C CERA 50V B 1000PF K (AXIAL)
51 RC636 RD-AZ473J- R CARBON FILM 1/6 47K OHM J
52 RCS33 RD-AZ473J- R CARBON FILM 1/6 47K OHM J
53 ZZ290 PTMPMSK016 PCB MAIN MANUAL AS DTQ-29U1SC
54 10 2193102005 SOLDER BAR SN:PB=63:47 S63S-1320
55 30 2291050616 FLUX SOLDER JS-64T3
56 40 2291050301 FLUX SOLVENT IM-1000
57 C331 CEYD1H689W C ELECTRO 50V RHD 6.8MF (16X35.5)
58 C404 CMYH3D722J C MYLAR 2KV BUP 7200PF J
59 C406 CMYE2G394J C MYLAR 400V PU 0.39MF J
60 C407 CMYH3D752J C MYLAR 2KV BUP 7500PF J
61 C409 CMYE2J273J C MYLAR 630V PU 0.027MF J
62 C801 CL1UC3104M C LINE ACROSS WORLD AC250V 0.1UF M R.47
63 C804 CEYD2D681D C ELECTRO 200V FHS 680MF (25X40)
64 D419 DRGP30J - DIODE RGP30J
65 D424 DDG3 DIODE DG3
66 D703 DLH2PR LED BLOCK LH-2P-R
67 D801 PTC1SW8902 HEAT SINK ASS‘Y DPBS606GU- + 7174300811
68 D801 DPBS606GU- DIODE BRIDGE PBS606G
69 D801A 4857018902 HEAT SINK A1050P-H24
70 D801B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
71 D807 PTS2SW6900 HEAT SINK ASS‘Y DFMLG16S + 7128301011
72 00001 DFM L G16 S DIODE FML-G16S
73 0000A 4857026900 HEAT SINK AL EX
74 0000B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
75 D842 DRGP30J - DIODE RGP30J
76 F801 5F1GB5021L FUSE GLASS TUBE CSA/UL 125V 5A
77 I201 1MM111 8 - IC A/V SWITCH MM1118
78 I301 PTC2SW8202 HEAT SINK ASS‘Y 1LA7848 - + 7174300811
79 00001 1LA7848 - IC VERTICAL LA7848
80 0000A 4857028202 HEAT SINK AL EX BK
81 0000B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
82 I401 PTM2SW6902 HEAT SINK ASS‘Y 1K78R05 - + 7174300811
83 00001 1K78R05 - IC REGULATOR KIA78R05PI
84 0000A 4857026902 HEAT SINK AL EX BK
85 0000B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
NO LOC PARTS CODE PARTS NAME PARTS DESCRIPTION REMARK
-16-
ELECTRICAL PARTS LIST
86 I501 1VDP3130Y- IC VDP3130Y
87 I502 1LP295033- IC REGULATOR LP2950 3.3V
88 I601 1MSP3420V3 IC SOUND PROCESSOR MSP3420G-PP-B8-V3
89 I602 PTB2SW8216 HEAT SINK ASS‘Y 1TDA8944J- + 7174301011
90 00001 1TDA8944J- IC SOUND TDA8944J
91 0000A 4857028216 HEAT SINK AL EX
92 0000B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
93 I701 1DW8638TA1 IC MICOM LC863856A-51S2
94 I703 124LC16B1B IC MEMORY 24LC16B1B
95 I801 PTD2SW8216 HEAT SINK ASS‘Y 1MR2540 - + 7174301011
96 00001 1MR2540 - IC POWER MR2540
97 0000A 4857028216 HEAT SINK AL EX
98 0000B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
99 I804 1LTV817C IC PHOTO COUPLER LTV-817C
100 I805 1LTV817C IC PHOTO COUPLER LTV-817C
101 IL701 1356VF6 - IC PREAMP 356VF6
102 JP01 4859111550 JACK PIN BOARD YPJ501B
103 JP02 4859106440 JACK S-VHS PH-SJ-9503
104 JP03 4859107050 JACK PIN BOARD PH-JB-9601 (PH06P-4120-C)
105 L301 58C7070085 COIL CHOKE TLN-3062A
106 L401 58H0000064 COIL H-LINEARITY TRL-350B
107 L801 5PLF30A1 FILTER LINE LF-30A1
108 M682 4856812001 TIE CABLE NYLON66 DA100
109 PWC1 4859907810 CORD POWER AS ME301P+TER=2100
110 Q401 TKTC3229 TR KTC3229
111 Q402 PTH2SW7609 HEAT SINK ASS‘Y T2SD2578 + 7174301011
112 00001 T2SD2578 TR HORI 2SD2578
113 0000A 4857027609 HEAT SINK AL EX
114 0000B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
115 Q804 TKTA1659AY TR KTA1659AY
116 R801 RX10B109JQ R CEMENT 10W 1 OHM J BEN 25MM 4P
117 R883 DDB3R0M140 POSISTOR ECPBD3R0M140
118 RLY1 5SC0101003 SW RELAY DG12D1-0(M)-II 1C-1P
119 RS801 DSVC471D14 VARISTOR SVC471D14A
120 SW707 5S50101035 SW TACT KPT-1112 1C-1P
121 T401 5TD0000018 TRANS DRIVE THD-120
122 T402 50H0000189 FBT FFA94048L
123 T402A 7178301212 SCREW TAPPTITE TT2 WAS 3X12 MFZN BK
124 T801 50M5345B9- TRANS SMPS TSM-5345B9
125 U101 4859723230 TUNER VARACTOR 115-V-F025AR
126 X501 5XE20R250E CRYSTAL QUARTZ HC-49/U 20.2500MHZ 30PPM
127 X601 5XE18R432E CRYSTAL QUARTZ HC-49/U 18.43200MHZ 30PPM
128 X701 5XYR03276C CRYSTAL QUARTZ C-001R 32.768000KHZ 20PPM
129 ZZ200 PTMPJ2K016 PCB CHIP MOUNT B AS DTQ-29U1SC
130 JC002 HRFT000-BA R CHIP 1/10 0 OHM 1608
NO LOC PARTS CODE PARTS NAME PARTS DESCRIPTION REMARK
-17-
ELECTRICAL PARTS LIST
131 JC003 HRFT000-BA R CHIP 1/10 0 OHM 1608
132 JC004 HRFT000-BA R CHIP 1/10 0 OHM 1608
133 JC005 HRFT000-BA R CHIP 1/10 0 OHM 1608
134 JC006 HRFT000-BA R CHIP 1/10 0 OHM 1608
135 JC007 HRFT000-BA R CHIP 1/10 0 OHM 1608
136 JC008 HRFT000-BA R CHIP 1/10 0 OHM 1608
137 JC009 HRFT000-BA R CHIP 1/10 0 OHM 1608
138 RC103 HRFT102JBA R CHIP 1/10 1K OHM J 1608
139 RC104 HRFT102JBA R CHIP 1/10 1K OHM J 1608
140 RC202 HRFT750JBA R CHIP 1/10 75 OHM J 1608
141 RC204 HRFT103JBA R CHIP 1/10 10K OHM J 1608
142 RC205 HRFT750JBA R CHIP 1/10 75 OHM J 1608
143 RC206 HRFT102JBA R CHIP 1/10 1K OHM J 1608
144 RC207 HRFT750JBA R CHIP 1/10 75 OHM J 1608
145 RC208 HRFT750JBA R CHIP 1/10 75 OHM J 1608
146 RC209 HRFT512JBA R CHIP 1/10 5.1K OHM J 1608
147 RC210 HRFT750JBA R CHIP 1/10 75 OHM J 1608
148 RC211 HRFT102JBA R CHIP 1/10 1K OHM J 1608
149 RC212 HRFT101JBA R CHIP 1/10 100 OHM J 1608
150 RC213 HRFT750JBA R CHIP 1/10 75 OHM J 1608
151 RC214 HRFT101JBA R CHIP 1/10 100 OHM J 1608
152 RC310 HRFT103JBA R CHIP 1/10 10K OHM J 1608
153 RC311 HRFT363JBA R CHIP 1/10 36K OHM J 1608
154 RC312 HRFT133JBA R CHIP 1/10 13K OHM J 1608
155 RC351 HRFT362JBA R CHIP 1/10 3.6K OHM J 1608
156 RC360 HRFT562JBA R CHIP 1/10 5.6K OHM J 1608
157 RC361 HRFT103JBA R CHIP 1/10 10K OHM J 1608
158 RC362 HRFT473JBA R CHIP 1/10 47K OHM J 1608
159 RC363 HRFT113JBA R CHIP 1/10 11K OHM J 1608
160 RC418 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
161 RC454 HRFT391JBA R CHIP 1/10 390 OHM J 1608
162 RC455 HRFT331JBA R CHIP 1/10 330 OHM J 1608
163 RC501 HRFT101JBA R CHIP 1/10 100 OHM J 1608
164 RC502 HRFT101JBA R CHIP 1/10 100 OHM J 1608
165 RC503 HRFT101JBA R CHIP 1/10 100 OHM J 1608
166 RC504 HRFT103JBA R CHIP 1/10 10K OHM J 1608
167 RC507 HRFT102JBA R CHIP 1/10 1K OHM J 1608
168 RC509 HRFT303JBA R CHIP 1/10 30K OHM J 1608
169 RC518 HRFT682JBA R CHIP 1/10 6.8K OHM J 1608
170 RC519 HRFT682JBA R CHIP 1/10 6.8K OHM J 1608
171 RC520 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
172 RC523 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
173 RC524 HRFT332JBA R CHIP 1/10 3.3K OHM J 1608
174 RC525 HRFT241JBA R CHIP 1/10 240 OHM J 1608
175 RC526 HRFT223JBA R CHIP 1/10 22K OHM J 1608
NO LOC PARTS CODE PARTS NAME PARTS DESCRIPTION REMARK
-18-
ELECTRICAL PARTS LIST
176 RC527 HRFT122JBA R CHIP 1/10 1.2K OHM J 1608
177 RC532 HRFT101JBA R CHIP 1/10 100 OHM J 1608
178 RC534 HRFT103JBA R CHIP 1/10 10K OHM J 1608
179 RC541 HRFT101JBA R CHIP 1/10 100 OHM J 1608
180 RC542 HRFT101JBA R CHIP 1/10 100 OHM J 1608
181 RC543 HRFT101JBA R CHIP 1/10 100 OHM J 1608
182 RC549 HRFT750JBA R CHIP 1/10 75 OHM J 1608
183 RC551 HRFT750JBA R CHIP 1/10 75 OHM J 1608
184 RC553 HRFT101JBA R CHIP 1/10 100 OHM J 1608
185 RC554 HRFT102JBA R CHIP 1/10 1K OHM J 1608
186 RC556 HRFT680JBA R CHIP 1/10 68 OHM J 1608
187 RC557 HRFT223JBA R CHIP 1/10 22K OHM J 1608
188 RC560 HRFT133JBA R CHIP 1/10 13K OHM J 1608
189 RC561 HRFT102JBA R CHIP 1/10 1K OHM J 1608
190 RC562 HRFT102JBA R CHIP 1/10 1K OHM J 1608
191 RC601 HRFT101JBA R CHIP 1/10 100 OHM J 1608
192 RC602 HRFT101JBA R CHIP 1/10 100 OHM J 1608
193 RC603 HRFT103JBA R CHIP 1/10 10K OHM J 1608
194 RC604 HRFT102JBA R CHIP 1/10 1K OHM J 1608
195 RC606 HRFT102JBA R CHIP 1/10 1K OHM J 1608
196 RC611 HRFT101JBA R CHIP 1/10 100 OHM J 1608
197 RC612 HRFT101JBA R CHIP 1/10 100 OHM J 1608
198 RC613 HRFT101JBA R CHIP 1/10 100 OHM J 1608
199 RC614 HRFT101JBA R CHIP 1/10 100 OHM J 1608
200 RC615 HRFT101JBA R CHIP 1/10 100 OHM J 1608
201 RC616 HRFT101JBA R CHIP 1/10 100 OHM J 1608
202 RC623 HRFT102JBA R CHIP 1/10 1K OHM J 1608
203 RC628 HRFT101JBA R CHIP 1/10 100 OHM J 1608
204 RC629 HRFT101JBA R CHIP 1/10 100 OHM J 1608
205 RC702 HRFT473JBA R CHIP 1/10 47K OHM J 1608
206 RC704 HRFT101JBA R CHIP 1/10 100 OHM J 1608
207 RC705 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
208 RC706 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
209 RC707 HRFT101JBA R CHIP 1/10 100 OHM J 1608
210 RC709 HRFT152JBA R CHIP 1/10 1.5K OHM J 1608
211 RC711 HRFT102JBA R CHIP 1/10 1K OHM J 1608
212 RC712 HRFT101JBA R CHIP 1/10 100 OHM J 1608
213 RC713 HRFT101JBA R CHIP 1/10 100 OHM J 1608
214 RC721 HRFT102JBA R CHIP 1/10 1K OHM J 1608
215 RC723 HRFT101JBA R CHIP 1/10 100 OHM J 1608
216 RC724 HRFT102JBA R CHIP 1/10 1K OHM J 1608
217 RC732 HRFT102JBA R CHIP 1/10 1K OHM J 1608
218 RC733 HRFT102JBA R CHIP 1/10 1K OHM J 1608
219 RC734 HRFT102JBA R CHIP 1/10 1K OHM J 1608
220 RC735 HRFT102JBA R CHIP 1/10 1K OHM J 1608
NO LOC PARTS CODE PARTS NAME PARTS DESCRIPTION REMARK
-19-
ELECTRICAL PARTS LIST
221 RC736 HRFT103JBA R CHIP 1/10 10K OHM J 1608
222 RC737 HRFT103JBA R CHIP 1/10 10K OHM J 1608
223 RC738 HRFT471JBA R CHIP 1/10 470 OHM J 1608
224 RC742 HRFT102JBA R CHIP 1/10 1K OHM J 1608
225 RC743 HRFT102JBA R CHIP 1/10 1K OHM J 1608
226 RC744 HRFT102JBA R CHIP 1/10 1K OHM J 1608
227 RC745 HRFT512JBA R CHIP 1/10 5.1K OHM J 1608
228 RC746 HRFT222JBA R CHIP 1/10 2.2K OHM J 1608
229 RC747 HRFT392JBA R CHIP 1/10 3.9K OHM J 1608
230 RC748 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
231 RC750 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
232 RC751 HRFT471JBA R CHIP 1/10 470 OHM J 1608
233 RC752 HRFT471JBA R CHIP 1/10 470 OHM J 1608
234 RC756 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
235 RC757 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
236 RC758 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
237 RC759 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
238 RC769 HRFT102JBA R CHIP 1/10 1K OHM J 1608
239 RC780 HRFT101JBA R CHIP 1/10 100 OHM J 1608
240 RC782 HRFT331JBA R CHIP 1/10 330 OHM J 1608
241 RC784 HRFT514JBA R CHIP 1/10 510K OHM J 1608
242 RC785 HRFT101JBA R CHIP 1/10 100 OHM J 1608
243 RC786 HRFT102JBA R CHIP 1/10 1K OHM J 1608
244 RC787 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
245 RC788 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
246 RC789 HRFT473JBA R CHIP 1/10 47K OHM J 1608
247 RC790 HRFT103JBA R CHIP 1/10 10K OHM J 1608
248 RC791 HRFT102JBA R CHIP 1/10 1K OHM J 1608
249 RC792 HRFT361JBA R CHIP 1/10 360 OHM J 1608
250 RC793 HRFT361JBA R CHIP 1/10 360 OHM J 1608
251 RC794 HRFT361JBA R CHIP 1/10 360 OHM J 1608
252 RC795 HRFT103JBA R CHIP 1/10 10K OHM J 1608
253 RC796 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
254 RC797 HRFT471JBA R CHIP 1/10 470 OHM J 1608
255 RC798 HRFT103JBA R CHIP 1/10 10K OHM J 1608
256 RC806 HRFT102JBA R CHIP 1/10 1K OHM J 1608
257 RC869 HRFT154JBA R CHIP 1/10 150K OHM J 1608
258 RC871 HRFT102JBA R CHIP 1/10 1K OHM J 1608
259 RC872 HRFT122JBA R CHIP 1/10 1.2K OHM J 1608
260 RC873 HRFT103JBA R CHIP 1/10 10K OHM J 1608
261 RC874 HRFT202JBA R CHIP 1/10 2K OHM J 1608
262 RC875 HRFT752JBA R CHIP 1/10 7.5K OHM J 1608
263 RC876 HRFT472JBA R CHIP 1/10 4.7K OHM J 1608
264 RC877 HRFT103JBA R CHIP 1/10 10K OHM J 1608
265 ZZ200 PTMPJ0K016 PCB MAIN (RHU) AS DTQ-29U1SC
NO LOC PARTS CODE PARTS NAME PARTS DESCRIPTION REMARK
-20-
ELECTRICAL PARTS LIST
266 C310 CEXF1E222V C ELECTRO 25V RSS 2200MF (16X25) TP
267 C381 CMXM2A224J C MYLAR 100V 0.22MF J
268 C405 CEXA2D229E C ELECTRO 200V RUL 2.2MF (10X16) TP
269 C414 CEXF1V471V C ELECTRO 35V RSS 470MF (10X20) TP
270 C415 CEXF1C102V C ELECTRO 16V RSS 1000MF (10X20) TP
271 C420 CEXF2E220V C ELECTRO 250V RSS 22MF (13X20) TP
272 C628 CEXF1E222V C ELECTRO 25V RSS 2200MF (16X25) TP
273 C630 CMXM2A224J C MYLAR 100V 0.22MF J
274 C632 CMXM2A224J C MYLAR 100V 0.22MF J
275 C633 CMXM2A224J C MYLAR 100V 0.22MF J
276 C634 CMXM2A224J C MYLAR 100V 0.22MF J
277 C702 CEXF1C102V C ELECTRO 16V RSS 1000MF (10X20) TP
278 C809 CBXB3D102K C CERA SEMI 2KV BL(N) 1000PF K (T)
279 C812 CEXF1E222V C ELECTRO 25V RSS 2200MF (16X25) TP
280 C813 CBXB3D471K C CERA SEMI 2KV BL(N) 470PF K (T)
281 C814 CEXF2C101V C ELECTRO 160V RSS 100MF (16X25) TP
282 C815 CEXF2A470V C ELECTRO 100V RSS 47MF (10X16) TP
283 C820 CEXF2C101V C ELECTRO 160V RSS 100MF (16X25) TP
284 C852 CEXF1E222V C ELECTRO 25V RSS 2200MF (16X25) TP
285 C880 CH1BEE472M C CERA AC U/C/V 2.5KV 4700PF TP
286 C881 CH1BEE472M C CERA AC U/C/V 2.5KV 4700PF TP
287 ZZ200 PTMPJBK016 PCB MAIN M-10 AS DTQ-29U1SC
288 10 2TM18006BE TAPE MASKING 6.2X500
289 E001 4856310300 EYE LET BSR T0.2 (R1.6)
290 E002 4856310300 EYE LET BSR T0.2 (R1.6)
291 E003 4856310300 EYE LET BSR T0.2 (R1.6)
292 E004 4856310300 EYE LET BSR T0.2 (R1.6)
293 E005 4856310300 EYE LET BSR T0.2 (R1.6)
294 E006 4856310300 EYE LET BSR T0.2 (R1.6)
295 E007 4856310300 EYE LET BSR T0.2 (R1.6)
296 E008 4856310300 EYE LET BSR T0.2 (R1.6)
297 E009 4856310300 EYE LET BSR T0.2 (R1.6)
298 E010 4856310300 EYE LET BSR T0.2 (R1.6)
299 E011 4856310300 EYE LET BSR T0.2 (R1.6)
300 E012 4856310300 EYE LET BSR T0.2 (R1.6)
301 E013 4856310300 EYE LET BSR T0.2 (R1.6)
302 E014 4856310300 EYE LET BSR T0.2 (R1.6)
303 E015 4856310300 EYE LET BSR T0.2 (R1.6)
304 E016 4856310300 EYE LET BSR T0.2 (R1.6)
305 E017 4856310300 EYE LET BSR T0.2 (R1.6)
306 E018 4856310300 EYE LET BSR T0.2 (R1.6)
307 E019 4856310300 EYE LET BSR T0.2 (R1.6)
308 E020 4856310300 EYE LET BSR T0.2 (R1.6)
309 E021 4856310300 EYE LET BSR T0.2 (R1.6)
310 E022 4856310300 EYE LET BSR T0.2 (R1.6)
NO LOC PARTS CODE PARTS NAME PARTS DESCRIPTION REMARK
Loading...