CH2 - CH6
VHF(H) : C-W+11
CH7 - CH13
UHF : W + 12 - W + 84
7W+7W5W+5W
8 ohm
75 ohm Unbalanced
Side : Video, Audio(R,L)
Rear : Video, Audio(R,L)
Rear: Video, Audio(R,L)
Picture IF Carrier Frequency : 45.75MHz
Sound IF Carrier Frequency : 41.25MHz
Color Sub-Carrier Frequency : 3.579545MHz
12W x 2EA
Front : Video, Audio(R,L)
Rear : Video, Audio(R,L)
AC120V 60Hz
125W
Remote Control
Special Function
R-43A07
1) Icon Type
2) 4-Language OSD
3) With CAPTION
4) CH Label
5) Digital Sensor (29M2FS)
6) Surround
7) AVC
8) Wide Picture(Option)
DAEWOO ELECTRONICS CO., LTD.
http : //svc.dwe.co.kr Sep. 2002
-1-
83
69
62
66
13
10
3
4
2
71
83
84
85
56
87
87
88
88
✐ CAUTION : In this Service Manual, some parts can be changed for improving their
performance without notice in the parts list. So, if you need the latest parts
information, please refer to PPL(Parts Price List)in Service information
Center(http://svc.dwe.co.kr)
Picture IF Carrier Frequency : 45.75MHz
Sound IF Carrier Frequency : 41.25MHz
Color Sub-Carrier Frequency : 3.579545MHz
R-43A07
130W
Frequency Synthesizer(FS)Tuning System
1) Icon Type
2) 4-Language OSD
3) With CAPTION
4) CH Label
DTQ-29M2FSDTQ-29M5SSNDTQ-29U8SSNDTQ-27U8SCN
Model
Items
TV Standard
Power Input
Power Consumption
Tuning System
Tuning Ranges
Sound Output
Speaker
Antenna Input Impedance
Intermediate Frequencies
Remote Control
Special Function
12W x 2EA
Auxiliary Input Terminal
Auxiliary Output Terminal
Rear: Video , Audio(R,L)
5) Digital Sensor (29M2FS)
6) Surround
7) AVC
8) Wide Picture(Option)
CHASSIS
CN-012NCN-012NACN-012NF
Side : Video, Audio(R,L)
Rear : Video, Audio(R,L)
Front : Video, Audio(R,L)
Rear : Video, Audio(R,L)
-3-
CIRCUIT BLOCK DIAGRAM
TEA5101B
(29U8)
STR-F6626
(27U8SCN Only)
CN-012N/NA/NF
-4-
ALIGNMENT INSTRUCTION
1. POWER
use this button to turn your TV on or off.
2. MUTE
Use to turn the TV's sound on and off.
3. CH
Use these buttons to change your TV's volume, to
activate selections in the menu system.
4. VOL
Use thesebuttons to change your TV's volume, to
activate selections in the meny system, or to change
audio and video settings.
5. MENU
Use this button to turn the TV's menu system on and off.
6. DISPLAY
Use this button to display the channel numbeer and
status.
7. INPUT
Use this button to select the TV's signal source.
8. VIDEO
Use this button to display video adjustment.
9. 0-9
Use these buttons to change channels.
10. SLEEP
Use this button to program the TV to turn off after a
certain time.
11. PREVIOUS
Use this button to return to the previous channel you
were watching.
1
3
4
11
8
7
2
4
5
3
9
10
6
POWERMUTE
MENU
CH
SLEEP PREVIOUS
VIDE OINPU TDISPLAY
1 2 3
4 5 6
7 8
0
9
VOL VOL
Your Remote Control(R-43A07)
-5-
ALIGNMENT INSTRUCTION
1. SERVICE MODE ADJUSTMENTS
Follow the steps below whenever service adjustment is required. See Table- A and Table- B to determine if
service adjustments are required.
1) How to enter the service mode using the user remote control.
•
Turn the set on.
•
Direct the remote control to the reception window of TV.
•
Push buttons of remote control in sequence as follows.
1 Æ MUTE Æ DISPLAY Æ MUTE
•
Then, the screen will appear as follows.
•
Using the channel up or channel down button, select the item you wish to adjust.
(The color of selected item turns into the red.)
•
Press the volume up or down button to enter in the service mode you wish to adjust.
2) How to memorize the adjusted values in the service mode.
•
Must press
DISPLAY
button the state which the screen is displaying each of service
menus
after all adjustments are completed each of all service menu.
Table-A : Adjust the values of service mode when a part is replaced.
PART
REPLACED
ADJUSTMENT
NOTES
NECESSARY UNNECESSARY
I701
(U-COM)
O
Data is stored in I703.
I101
(MAIN)
O
I702
(EEPROM)
Initial setting values are written from I701.
ADJUSTING ITEMS
S5 : RFAGCD
O S6 : H.PHASE/V.POSI/V.SIZE
S8 : RD/GD/BD/RB/GB/BB
S9 Subbrightness
CRT O Adjust items related to picture tube only.(White Balance adjustment)
S2 SCRN
S5 IFC
S6 GEO
S8 W/B
S9 DP
S12 FACT
-6-
ALIGNMENT INSTRUCTION
Table-B
*
indicates the items with different settings each of sets
2. ASSEMBLY ADJUSTMENTS
1) SCREEN ADJUSTMENT (S2)
•
Enter the service mode and select service adjustment S2.
•
You can see the one horizontal line on the screen.
•
Adjust the Screen Control Volume (located on FBT) so that the horizontal line onscreen may be
disappeared.
•
Press the volume up or down button to exit in the screen adjustment mode.
MODEADJUSTMENT
DATA
REMARKS
INITIALRANGE
S2Screen Adjustment
S5
IF CONTROL
RF AGC DELAY *200 ~63Align RF AGC threshold
AGC POINT3.753.25~4.0Select AGC reference voltage
A/D VALUE-FM/AM PRESCALE180~255Must be set to 18
SCART PRESCALE180~255Must be set to 18
MONITOR VOLUME1190~255Must be set to 119
S6(4:3)
H-CENTER *110~31Align sync to flyback pulse,using internal cross pattern(s11)
V-CENTER *220~63Align vertical DC bias,using internal cross pattern(s11)
V-LIN *120~31Must be set to 12
H-SIZE *320~63Align sync to flyback pulse,using internal cross pattern(s11)
V-SIZE *960~127Align vertical amplitude,using internal cross pattern(s11)
V-S120~31Must be set to 12
V-SIZE-C70~7Must be set to 7
P-CUSHION *300~63Align pincution,using internal cross pattern(s11)
TILT *370~63Align tilt,using internal cross pattern(s11)
TOP-C80~15Must be set to 8
BOT-C80~15Must be set to 8
S8
R-DRIVE *630~127Align red out AC level
G-DRIVE *150~15Must be set to 15
B-DRIVE *630~127Align blue out AC level
R-BIAS *1270~255Align red out DC level
G-BIAS *1270~255Must be set to 127
B-BIAS *1270~255Align blue out DC level
S9
SUB-BRIGHT *750~127Align common RGB DC level
DP-CONTRAST270~27
DP-SHARPNESS50~30
DP-COLOR270~27
DP-TINT380~77
VIDEO LEVEL70~7
FM LEVEL300~31
S11
internal black--Display internal black pattern
internal 100% white--Display internal 100% white
internal 60% white--Display internal 60% white
internal cross pattern--Display internal cross pattern
S12Forwarding Mode-Factory initialization
IN THE SCREEN ADJUSTMENT MODE, DONT PRESS OTHER BUTTONS EXCEPT VOLUME UP OR DOWN BUTTON.
CAUTION
-7-
ALIGNMENT INSTRUCTION
2) FOCUS ADJUSTMENT
•
Turn in a local station and adjust the Focus Control knob (located on FBT) for best picture
details at high light condition.
3) RF AGC DELAY ADJUSTMENT (S5)
•
Receive a good local channel.
•
Enter the service mode and select service adjustment S5.
•
You can see the OSD as shown in below.
•
Select RFAGCD item, press the volume up or down button until noise or beat in picture disappears.
•
Press the DISPLAY button to memorize the data.
4) GEOMETRIC ADJUSTMENTS (S6)
•
Enter the service mode and select service adjustment S11.
•
Whenever you select the “S11” using the volume up or down button, the screen is changing like this.
•
Using the volume up or down button, select internal cross pattern.
•
Select service adjustment S6
•
You can see the OSD as shown in below.
4-1. Horizontal Position Adjustment
•
Select H-CENTER item, adjust H-CENTER data value to obtain proper horizontal centering of the
internal cross pattern at the left and right of the screen.
4-2. Vertical Position Adjustment
•
Select V-CENTER item, adjust V-CENTER data value to center the raster properly on the screen.
860000A4857026902HEAT SINKAL EX BKR
870000B7178301212SCREW TAPPTITETT2 WAS 3X12 MFZN BK
88I5011LA76834--IC MAINLA76834R
89I5021TDA9183P-IC COMBFILTERTDA9183PR
516Q706TKTC3198Y-TRKTC3198YR
517Q802TKTC3198Y-TRKTC3198YR
518Q803TKTC3198Y-TRKTC3198YR
519Q804TKTC3198Y-TRKTC3198YR
520R103RN02B910JSR METAL FILM2W 91 OHM J SMALL
521R204RN02B471JSR METAL FILM2W 470 OHM J SMALL
522R303RN02B620JSR METAL FILM2W 62 OHM J SMALL
523R304RN02B109JSR METAL FILM2W 1 OHM J SMALL
524R305RN02B109JSR METAL FILM2W 1 OHM J SMALL
525R309RN02B221JSR METAL FILM2W 220 OHM J SMALL
526R311RN02B221JSR METAL FILM2W 220 OHM J SMALL
527R315RN01B272JSR METAL FILM1W 2.7K OHM J SMALL
528R316RN01B562JSR METAL FILM1W 5.6K OHM J SMALL
529R320RN01B750JSR METAL FILM1W 75 OHM J SMALL
530R401RN02B680JSR METAL FILM2W 68 OHM J SMALL
531R402RN02B680JSR METAL FILM2W 68 OHM J SMALL
532R410RN02B103JSR METAL FILM2W 10K OHM J SMALL
533R420RN02B333JSR METAL FILM2W 33K OHM J SMALL
534R450RN02B151JSR METAL FILM2W 150 OHM J SMALL
535R451RN02B271JSR METAL FILM2W 270 OHM J SMALL
576D71085801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
577D71185801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
578D71285801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
579D71385801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
580D719D1N4148---DIODE1N4148 (TAPPING)R
-25-
ELECTRICAL PARTS LIST
NOLOCPARTS CODEPARTS NAMEPARTS DESCRIPTIONREMARK
581D721DMTZJ5R6B-DIODE ZENERMTZJ 5.6B R
582D723DMTZJ5R6B-DIODE ZENERMTZJ 5.6B R
583D803D1N4937G--DIODE1N4937G (TAPPING)R
584D804D1N4937G--DIODE1N4937G (TAPPING)R
585D805D1N4937G--DIODE1N4937G (TAPPING)R
586D807D1N4937G--DIODE1N4937G (TAPPING)R
587D808D1N4937G--DIODE1N4937G (TAPPING)R
588D812D1N4937G--DIODE1N4937G (TAPPING)R
589D814D1N4937G--DIODE1N4937G (TAPPING)R
590DS213DMTZJ5R6B-DIODE ZENERMTZJ 5.6B R
591DS601DMTZJ5R6B-DIODE ZENERMTZJ 5.6B R
592DS622DMTZJ5R6B-DIODE ZENERMTZJ 5.6B R
593DS623DMTZJ5R6B-DIODE ZENERMTZJ 5.6B R
594J00185801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
595J00285801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
596J00385801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
597J00485801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
598J00585801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
599J00685801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
600J00785801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
601J00885801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
602J00985801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
603J01085801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
604J01185801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
605J01285801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
606J01385801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
607J01485801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
608J01585801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
609J01685801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
610J01785801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
611J01885801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
612J01985801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
613J02085801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
614J02185801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
615J02285801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
616J02385801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
617J02485801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
618J02585801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
619J02685801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
620J02785801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
621J02885801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
622J02985801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
623J03085801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
624J03185801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
625J03285801065GYWIRE COPPERAWG22 1/0.65 TIN COATING
-26-
Loading...
+ 62 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.