Daewoo DTQ-27U1SCV, DTQ-27U4SCV Instruction Manual

COLOR TELEVISION

INSTRUCTION MANUAL

DTQ-27U1SC
DTQ-27U4SC
DTQ-27U1SCV
DTQ-27U4SCV

401E101-R0 2005.4.4 11:34 AM 페이지100

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and servicing instructions in the literature accompanying
the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.

CAUTION

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

NOTE TO CATV SYSTEM INSTALLER

THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE
820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR,
SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE
BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.

CAUTION

The AC power cord provided with this product is polarized (one blade wider than the other).
To prevent electrical shock, match wide blade of plug to wide slot, fully insert the AC plug into a stan­dard 120V AC, 60Hz polarized outlet.

NOTE

Never connect the plug to an electrical source other than one providing 120V AC, 60Hz power. Use only the attached power
cord. If the polarized AC cord does not fit into a non-polarized outlet, do not cut or file the blade. You are responsible for hav­ing the obsolete outlet replaced with a polarized outlet.

If you feel a static discharge when touching the unit, and the unit does not function, simply unplug the unit from the outlet.
When you plug the unit back in, it should work normally.

Do not install power cords near any heating element or cooking appliances.

401E101-R0 2005.4.4 11:34 AM 페이지51

Important Safeguards

SAFETY

IMPORTANT SAFEGUARDS

PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TELEVISION EQUIPMENT AND
RETAIN FOR FUTURE REFERENCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED
ON THE TV RECEIVER.

1

Read all of these instructions.

2

Save these instructions for later use.

3

Unplug this television equipment from the wall
outlet before cleaning. Do not use liquid clean­ers or aerosol cleaners. Use a damp cloth for
cleaning.

4

Do not use attachments not recommended by
the television equipment manufacturer as they
may result in the risk of fire, electric shock or
other personal injury.

5

Do not use this television equipment near
water, for example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet basement,
or near a swimming pool, or the like.

6

Do not place this television equipment on an
unstable cart, stand, or table. The television
equipment may fall, causing serious injury to a
child or adult, and serious damage to the equip­ment. Use only with a cart or stand recom­mended by the manufacturer, or sold with the
television equipment. Wall or shelf mounting
should follow the manufacturer's instructions,
and should use a mounting kit approved by the
manufacturer.

6A

An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance
and cart combination to overturn.

7

Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to
ensure reliable operation of the television
equipment; and to protect it from overheating,
these openings, must not be blocked or covered.
The openings should never be blocked by plac­ing the television equipment on a bed, sofa, rug,
or other similar surface. (This equipment should
never be placed near or over a radiator or heat
register.) This television equipment should not
be placed in a built-in installation, such as a
bookcase, unless proper ventilation is provided.

8

This television equipment should be operated
only from the type of power source indicated on
the marking label. If you are not sure of the
type of power supplied to your home, consult
your television dealer or local power company.

9

This television equipment is equipped with a
polarized alternating current line plug (a plug
having one blade wider than the other). This
plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, con­tact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
polarized plug.

10

Do not allow anything to rest on the power
cord. Do not locate this television equipment
where the cord will be abused by persons walk­ing on it.

11

Follow all warnings and instructions marked on
the television equipment.

12

For added protection for this television equip­ment during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent
damage to the equipment due to lightning and
power-line surges.

401E101-R0 2005.4.4 11:34 AM 페이지52

Important Safeguards

13

An outside antenna system should not be locat­ed in the vicinity of overhead power lines or
other electric light or power circuits, or where it
can fall into such power lines or circuits. When
installing an outside antenna system, extreme
care should be taken to keep from touching such
power lines or circuits, as contact with them
might be fatal.

14

Do not overload wall outlets and extension
cords, as this can result in fire or electric shock.

15

Never push objects of any kind into this televi­sion equipment through openings, as they may
touch dangerous voltage points or short-out
parts that could result in a fire or electric shock.
Never spill liquid of any kind on the television
equipment.

16

Do not attempt to service this television equip­ment yourself, as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.

17

Unplug this television equipment from the wall
outlet and refer servicing to qualified service
personnel under the following conditions:

(a) When the power-supply cord or plug is dam-

aged or frayed.

(b) If liquid has been spilled, or objects have

fallen into the television equipment.

(c) If the television equipment has been exposed

to rain or water.

(d) If the television equipment does not operate

normally by following the operating instruc­tions. Adjust only those controls that are cov­ered by the operating instructions as an
improper adjustment of other controls may
result in damage and will often require exten­sive work by a qualified technician to restore
the TV receiver to its normal operation.

(e) If the television equipment has been dropped

or the cabinet has been damaged.

(f) When the television equipment exhibits a

distinct change in performance - this indi­cates a need for service.

18

When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer that have
the same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock or other hazards.

19

Upon completion of any service or repairs to
this television equipment, ask the service tech­nician to perform safety checks to determine
that the television is in a safe operating condi­tion.

20

If an outside antenna or cable system is con­nected to the television receiver, be sure the
antenna or cable system is grounded so as to
provided some protection against voltage
surges and built-up static charges.

Section 810 of the National Electrical Code,
ANSI/NFPA N0.70-1984, provides information
with respect to proper grounding of the mast
and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size
of grounding conductors, location of
antenna-discharge unit, connection to ground­ing electrodes, and requirements for the ground­ing electrode.

401E101-R0 2005.4.4 11:34 AM 페이지53

1

Table of Contents

CONTENTS

T able of Contents

Chapter 1: Overview of Your Equipment 2

Your TV's Front Panel 2
Your TV's Back Panel

3

Your Remote Control

4

Installing your remote control batteries

5

Notes

5

Chapter 2: Connecting an Antenna or Cable to Your TV 6

Connecting an Antenna 6
Antennas with two sets of leads

7

Connecting a Cable System

7

Connecting Other Pieces of Equipment

8

Safety Note

8

Chapter 3: Adjusting Video Settings 9

Returning to the factory settings 10
Descriptions of video settings

10

Chapter 4: Adjusting the Sound 11

Selecting stereo/SAP 11
Listening to stereo sound

11

Listening to second Language

12

Selecting Audio Mode

12

Adjusting of equalizer settings

13

Adjusting the Balance

13

Selecting the Surround Effect Mode

14

Selecting the Automatic Volume Controller

14

Chapter 5 : Operating Your TV 15

Turning Your TV On 15
Programming Your TV's Channel Memory

15

Changing Channels

16

Changing the Volume

16

Changing the TV's Channel Memory

17

Displaying the Current Channel

17

Ch Labels

18

Note

18

Changing the TV's Input

19

Chapter 6 : Using Timer Functions 20

Setting the Clock 20
Setting the Wake-up time

20

Setting the Off Time

21

Canceling the Wake-up Time or Off Time

21

Setting the Sleep Timer

22

Chapter 7 : Using the Special Features 23

Changing the Language of the On-screen Menus 23
Captioning

23

CC on Mute

24

Power Restore

24

Parental Control Settings

25

Description of Parental Control Settings

26

No Ratings means

27

Mini Glossary

27

Troubleshooting 28
Warranty 29

401E101-R0 2005.4.4 11:34 AM 페이지1

2

Chapter 1 :

Overview of Your Equipment

Overview of Your Equipment

Your TV comes with a remote control. The section below summarizes the buttons, controls, and ter­minals that you will use with your TV.

Your TV's Front Panel

1 POWER

Use this button to turn your TV on or off.

2 VIDEO IN jack

Use this jack to receive a video signal from another A/V component.

3 AUDIO IN jack

Use this jack to receive an audio signal from another A/V component.

4 POWER(red) indicator (Optional)

This indicator lights up when the TV is STAND-BY mode.

5 Remote control receiver

This receiver receives a signal from your remote control. Do not block it.

6 WCHV

Use these buttons to change channels on your TV, or to select items in the menu
system.

7 CVOLB

Use these buttons to change your TV's volume, to activate selections in the menu
system, or to change audio and video settings.

8 MENU

Use this button to turn the TV's menu system on and off.

9 TV/AV

Use this button to select main picture source.

2

9

CHAPTER

1

9

2

(MONO)

27U1

27U4

27U1

401E101-R0 2005.4.4 11:34 AM 페이지2

Your TV's Back Panel

1 Antenna terminal(ANT)

Use this terminal to attach an antenna or cable system to your TV.

2 VIDEO IN

These terminals allow the TV to receive video signals from another A/V components.
* S-VIDEO jack is used to receive the separated video signal, such as Y/C signals from the

S-VHS VCR.

3 AUDIO IN

This terminal allows the TV to receive audio signals from another A/V and S-VIDEO components.

4 VIDEO OUT

This terminal allows the other component to receive a video signal from your TV.
* This terminal is not effective on the COMPONENT mode.

5 AUDIO OUT

This terminal allows the other component to receive a audio signal from your TV.

6 Y / PB / PR or Y / Cb / Cr IN(COMPONENT VIDEO INPUT)

This terminal allows the TV to receive a Y/PB/PR signal from another component, such as DVD.

7 COMPONENT AUDIO INPUT

This terminal allows the TV to receive an audio signal from another component, such as a DVD.

3

Chapter 1 :

Overview of Your Equipment

27U4 27U1

401E101-R0 2005.4.4 11:34 AM 페이지3

Your Remote Control

1. POWER

Use this button to turn your TV on or off.

2. MUTE

Use to turn the TV’s sound on and off.

3. WCHV

Use these buttons to change channels on your TV,
or select items in the menu system.

4. C

VOL

B

Use these buttons to change your TV's volume, to
activate selections in the menu system, or to
change audio and video settings.

5. MENU

Use this button to turn the TV’s menu system on
and off.

6. DISPLAY

Use this button to display the present status.

7. INPUT

Use this button to select the TV’s signal source.

8. VIDEO

Use this button to display video adjustment
items.

9. 0-9

Use these buttons to change channels.

10. SLEEP

Use this button to program the TV to turn off after
a certain time.

11. PREVIOUS

Use this button to return to the previous channel
you were watching.

12. NOT USER

4

Chapter 1 :

Overview of Your Equipment

401E101-R0 2005.4.4 11:34 AM 페이지4

5

Chapter 1 :

Overview of Your Equipment

Installing your remote control batteries

1

Open the battery compartment on the back of the remote control.

2

Install two AAA-size batteries (not included) as shown. Make sure the “+” and “-” terminals are
oriented correctly.

3

Replace the cover.

Notes

Do not mix different types of batteries together or old batteries with fresh ones.
Remove and replace weak batteries. Weak batteries can leak and damage your controller. Dispose

of batteries properly; never throw them into a fire.
Point your remote at the receiver on the center of the front of the TV. Make sure the receiver is not

blocked.
The remote control can operate up to 30 feet away from the TV, if you are directly facing the front

of the TV. Operating distance diminishes as you move to the sides of the TV.

401E101-R0 2005.4.4 11:34 AM 페이지5

6

Chapter 2 :

Connecting an Antenna or Cable to Your TV

CHAPTER

2

Connecting an Antenna or Cable to Your TV

Your TV will provide you with the best performance if you connect it to an external antenna or
cable system. Follow the directions below make this connection. Please note that you will normally
only have to make one of the connections shown below, not all of them.

All connections will be made to the antenna terminal on the back of your TV. The antenna terminal
is a silver metal post partially surrounded by two plastic tabs. For help in locating the antenna termi­nal, see “Your TV’s Back Panel” on page 3.

Connecting an Antenna

If your antenna ends in a single coaxial lead, simply

press or screw the cable onto the antenna terminal on the
back of your TV.

If your antenna ends in a pair of 300 ohm twin leads, you must use a 300-ohm/75-ohm

adapter(available at your local electronics store). Place the leads underneath the screws on the
adapter, tighten the screws, then press the adapter onto the antenna terminal on the back of the TV.

(The rod antenna need to be purchased seperately.)

401E101-R0 2005.4.4 11:34 AM 페이지6

7

Chapter 2 :

Connecting an Antenna or Cable to Your TV

Antennas with two sets of leads

You might have two sets of leads from your antenna system, especially if you have one antenna for
VHF signals and one antenna for UHF signals.

If your antenna system has both a coaxial lead and twin 300-ohm leads

, you must obtain a combin-

er (available at your local electronics store). Press or screw the coaxial lead onto the combiner; place
the twin leads underneath the screws on the combiner and tighten the screws. Press the cable from
combiner onto the antenna terminal on the back of your TV.

Connecting a cable system

If your cable set-up is not described below, please
contact your cable company for more information.

If your cable system does not require the use of
a cable box,

simply press or screw the incoming
cable onto the antenna terminal on the back your
TV.

If your antenna system has two sets of twin 300-ohm leads,

you must obtain a combiner (available
at your local electronics store). Place one set of twin leads underneath the screws on the combiner
and tighten the screws. Do the same with the other set of twin leads. Press the cable from the com­biner onto antenna terminal on the back of your TV.

401E101-R0 2005.4.4 11:34 AM 페이지7