Daewoo DT-K6623P-KS3 User Manual

1280 HR TIME LAPSE RECORDER WITH 40HR REAL TIME REC

User’s Guide

EV-VCR960R

Be sure to read carefully and follow all the SAFETY INFORMATION on page i. Keep the manual in a safe place for future reference.

P/N : 97P95600P0-43

Time Lapse Video Cassette Recorder

AUTO SET

C H

Worth Knowing

Please keep the video machine's guarantee card and receipt safe for warranty purposes.

Precautions

◆ Read carefully through this manual to familiarize yourself with this

high–quality Time Lapse video cassette recorder.

◆ Make sure the rating of your household electricity supply matches that

shown on the back of the Time Lapse video cassette recorder.

◆ Refer to this chapter and the "Initial installation" chapter to help you

install and adjust your Time Lapse video cassette recorder. Do not ... ... expose the Time Lapse video cassette recorder to high levels of humidity

and heat, to avoid the risk of fire and electric shock.

... open the Time Lapse video cassette recorder. Have a qualified technician

carry out repairs.

... connect the Time Lapse video cassette recorder to the power supply if

you have just moved it from a cold to warm environment. This can result in condensation inside the recorder and cause serious damage to the machine and cassettes. Wait around two hours to allow it to reach room

temperature. Make sure ... ... the recorder is placed on a steady, flat surface. ... you place the recorder where there is good ventilation all around. ... you clean the recorder only with a soft, lint–free cloth; do not use

aggressive or alcohol–based cleaning agents. ... you disconnect the power supply if the recorder appears to be working

incorrectly, is making an unusual sound, has a strange smell, has smoke

emitting from it or liquids have got inside it. Have a qualified technician

check the recorder. ... you disconnect the power supply and aerial if you will not be using the

recorder for a long period or during a thunderstorm.

For your own safety!

◆ There are no components in this Time Lapse video cassette recorder

you can service or repair yourself.

◆ Do not open the case of the Time Lapse video cassette recorder. Only

allow qualified personnel to repair or service your set.

◆ This Time Lapse video cassette recorder is designed for continuous

operation. Switching it off does not disconnect it from the mains (stand–by). To disconnect it from the mains, you have to unplug it.

◆ Recording any copyright protected material may infringe a copyright.

Disposal of Used Electrical & Electronic Equipment

The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this equipment at your applicable collection point for the recycling of electrical & electronic equipments waste. In the European Union and Other European countries which there are separate collection systems for used electrical and electronic product. By ensuring the correct disposal of this product, you will help prevent potentially hazardous to the environment and to

human health, which could otherwise be caused by unsuitable waste handling of this product. The recycling of materials will help conserve natural resources. Please do not therefore dispose of your old electrical and electronic equipment with your household waste. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Time Lapse Video Cassette Recorder

Front Panel

Locations of controls and indicators

1 STOP button 2 REC button 3 REC CHECK button 4 EJECT button 5 CASSETTE LOADING

DOOR 6 DISPLAY PANEL 7 PLAY button 8 REW button 9 FF button 10 PAUSE/STILL button 11 REMOTE SENSOR 12 HIGH PICTURE switch 13 SET LOCK switch 14 RESET button 15 MENU button

16 SHIFT(†) /

TRACKING (–) button

17 SHIFT(√) /

TRACKING (+) button

18 REC/PLAY SPEED(†)

button (SET – button)

19 REC/PLAY SPEED(…)

button (SET +

button) 20 AUDIO ON button 21 DISPLAY button 22 STANDBY/ON button 23 COUNTER button 24 CLEAR button

Time Lapse Video Cassette Recorder

Locations of controls and indicators .............................................................................................. 1

Front Panel .............................................................................................................. 1

Digital Display ......................................................................................................... 2

Back Panel .............................................................................................................. 4

Remote Control ....................................................................................................... 5

Connections ................................................................................................................................. 6

Video Cassettes Tapes .................................................................................................................. 7

Types of On-screen displays and Display Sequence ...................................................................... 8

Setting the Clock ........................................................................................................................ 10

Changing the On-Screen Display ................................................................................................ 12

Normal Recording ...................................................................................................................... 14

Program Timer Recording .......................................................................................................... 16

Alarm Recording ........................................................................................................................ 20

Panic Recording ......................................................................................................................... 23

Series Recording ........................................................................................................................ 23

Autorepeat Recording ................................................................................................................ 25

Normal Playback ....................................................................................................................... 26

Normal Playback ................................................................................................... 26

Tracking Control / Vertical Lock Control ............................................................... 26

Audio Playback ...................................................................................................... 27

Special Playback ........................................................................................................................ 28

Digital Shuttle .........................................................................................................28

Reverse Play / Picture Search .................................................................................29

Still Image ............................................................................................................ 29

Recording Check / Alarm Search ........................................................................... 30

Alarm Scan / Index Search .................................................................................... 31

Other Functions .......................................................................................................................... 32

Tape counter (Zero Search) .................................................................................. 32

Setting the Security Lock (Set Lock) ...................................................................... 33

Setting the HIGH PICTURE ..................................................................................... 33

Setting the SW Out Terminal Output ...................................................................... 34

Setting the Buzzer .................................................................................................. 35

Checking the Alarm Recording Times .................................................................... 36

Checking Power Loss Times .................................................................................. 36

Setting In/Out Terminals ........................................................................................ 37

Daily Inspection ......................................................................................................................... 42

Troubleshooting Guide ............................................................................................................... 43

Specifications ............................................................................................................................. 45

Contents

Time Lapse Video Cassette Recorder

6 Power Loss indicator :

Flashes on after power loss.

7 CNT indicator : CNT

Comes on when the tape or alarm counter is on.

8 SPD indicator : SPD

Comes on when the play or recording speed is on.

9 HIGH PICTURE indicator : H.P

Comes on when the HIGH PICTURE sw is set to the “ON” position.

10 S.REC indicator : S.REC

Comes on when “YES” is selected in the menu for the series recording.

11 R.REC indicator : R.REC

Comes on when “YES” is selected in the menu for the repeat recording.

12 SET LOCK SW indicator :

Comes on when the SET LOCK sw is set to the “ON” position.

13 Mode display

• TAPE COUNTER display (eg:10:HOUR,59:MINUTE)

- Maximum Hour : 19 - Maximum Minute : 59

• ALARM COUNTER display (eg: A:Alarm , 32:Alarm No.)

• PLAY/REC SPEED display (eg: 30H:Play/Recording

Speed)

• TIME display (eg: 7:HOUR , 07:MINUTE)

• ERROR display (eg: E:Error , 04:Error No.)

- E-01 : The cassette cannot be loaded or unloaded.

- E-02 : The tape stops.

- E-03 : The drum can not rotate properly.

- E-04 : The tape is cut/broken.

• AUDIO ON display (eg: A:Audio , 18H:Play Speed)

Time Lapse Video Cassette Recorder

Digital Display

1 Operation Indicators display the actual operation

mode.

2 Cassette indicator :

Comes on when a cassette is loaded.

3 Record check indicator : REC

Flashes on during record check.

4 Alarm indicator :

Flashes on when an alarm is being recorded and stops flashing after alarm recording.

5 Timer Recording indicator :

Comes on when in timer recording stand-by mode, or during a timer recording.

Operation Mode Indicator

1 Record (REC) REC 2 Record pause (REC PAUSE) REC + » 3 Playback (PLAY) √ 4 Still image (STILL) √ + » 5 Fast forward (FF) √√ 6 Rewind (REW) œœ 7 CUE (CUE)+ √ + √√ 8 Review (REVIEW)+ √ + œœ 9 Slow (Pause Still + FF, √ + » +

Pause Still + REW) √ + » +

Time Lapse Video Cassette Recorder

Remote Control

1 POWER button 2 PLAY/STILL TRACKING + button 3 PLAY/STILL TRACKING – button 4 DIGITAL SHUTTLE + button 5 DIGITAL SHUTTLE – button 6 PLAY √ button 7 FF √√ button 8 STOP ■ button 9 EJECT button 10 REC/PLAY SPEED… button 11 SHIFT√ button 12 SHIFT† button 13 SET + button 14 SET – button 15 DISPLAY button 16 COUNTER button 17 CLEAR button 18 PAUSE/STILL button

19 REW œœ button 20 AUDIO ON button 21 REVERSE PLAY button 22 ● REC button 23 REC/PLAY SPEED† button 24 REC CHECK button 25 MENU button

Time Lapse Video Cassette Recorder

Back Panel

1 AC POWER CORD 2 WARNING OUT terminal 3 SERIES IN terminal 4 COM terminal 5 SERIES OUT terminal 6 SW OUT terminal 7 VIDEO OUT jack 8 VIDEO IN jack 9 AUDIO IN jack 10 TAPE END terminal 11 PANIC IN terminal 12 COM terminal 13 ALARM OUT terminal 14 ALARM IN terminal 15 MIC(microphone input) jack 16 AUDIO OUT jack

Time Lapse Video Cassette Recorder

Connections

Connect the video camera and monitor TV as shown in the figure below.

NOTE : Make sure to turn the power off on all devices

before making the connections.

Power Cord Installation

Insert the plug of the power cord into an outlet.

Video Cassettes Tapes

Use only video cassette tapes bearing the $ logo.

This VCR was primarily designed for use with E-180 cassette tapes. It is recommended to use E-180 VHS or E240 VHS video cassette tapes for optimal performance.

Handling Cassette Tapes

Cassette tapes should always be stored vertically in their cases, away from high temperatures, magnetic fields, direct sunlight, dirt, dust and locations subject to mold formation.

Do not tamper with the cassette mechanism. Never touch the tape with your fingers. Protect cassette tapes from shocks or strong vibrations.

To Protect your recordings

After having recorded a tape, if you wish to keep the recording, use a flathead screwdriver to break off the erasure-prevention tab on the cassette.

To record again on a tape without erasure-prevention tab, cover the hole with adhesive tape.

Erasure-prevention tab

To prevent accidental erasure, remove the tab after recording.

To record again, cover the hole with vinyl tape.

Place the cassette, label side up, in the loading slot. Gently push the center of the cassette until it is loaded automatically.

Unloading

In STOP mode, press the EJECT button. The cassette is automatically ejected.

✔

• If you try to record on a cassette without the erasureprevention tab, the VCR will eject the cassette.

• If the TIMER button is pressed when a cassette without the erasureprevention tab is loaded, the VCR will eject the cassette, the timer recording indicator ( ) will start flashing and a buzzer will sound if “YES” is set in the menu for buzzer.

✔

• When the cassette is loaded, the cassette indicator “ “ will light on the display panel.

• The counter display will switch to the reset counter “0H 00M 00S” display on the monitor screen. (“0H 00M” on the display panel.)

✔

• Do not insert any object in the cassette loading slot, as that may cause injury and damage to the VCR.

• If your hand gets stuck in the cassette loading slot, unplug the power cord and consult the dealer where the unit was bought. Do not forcibly pull the hand out as that may cause severe injuries.

Video camera

(sold separately)

To VIDEO OUT terminal

To VIDEO IN

terminal

From an external audio source

Monitor TV (sold separately)

Time Lapse Video Cassette Recorder

Types of On-screen displays and Display Sequence

• If the VCR is in timer recording stand-by mode (the “ ” indicator is displayed on the display panel), the on-screen displays will not be available. First press the STANDBY/ON(POWER) button, to cancel the recording stand-by mode, then proceed with the VCR programming. When finished, press the STANDBY/ON(POWER) button again to return the VCR to timer recording stand-by mode.

• When a menu is displayed, recording will not be possible.

• Press the MENU button three times, the setting procedure is now completed and the normal screen is displayed.

• During recording or playback the menus cannot be displayed.

• Press the MENU button. (First time)

• Press the SHIFT† button to move the arrow mark (√) downward for the desired item.

• Press the SHIFT√ button to select the desired item, then the desired menu is displayed.

• Press the MENU button to return to the normal screen from the initial menu.

• Press the SHIFT√ button to select the desired item.

• Press the SET – (or +) button to set or Press the SHIFT√ button to select

“YES” or “NO”.

• Press the MENU button to return to the initial menu.

• Press the SHIFT√ (or SHIFT†) button to select the desired item.

• Press the SET – (or +) button to set or Press the SHIFT√ button to select.

• Press the MENU button to return to the previous menu.

Time Lapse Video Cassette Recorder

6 Press the SET – (or +) button to set the minutes (eg

: 30), then press the SHIFT√ button. 7 The seconds are already set to “00”. 8 Press the SHIFT√ button. 9 Press the SET – (or +) button to set the day (eg :

12), then press the SHIFT√ button.

10 Press the SET – (or +) button to set the month (eg :

04), then press the SHIFT√ button.

11 Press the SET – (or +) button to set the year (eg :

10 for 2010).

• The last 2 digits only are displayed.

• The day of the week is set automatically.

12 Press the MENU button three times, the normal

screen is displayed.

• The setting procedure is now complete.

Time Lapse Video Cassette Recorder

Setting the Clock

Example: To set the clock to April 12, 2010 at 9:30

Clock Setting

1 Turn the power on to all devices used. 2 Press the MENU button, the initial MENU is displayed.

The arrow mark (√) is located in “VCR Mode Set”.

Initial MENU

3 Press the SHIFT√ button, the VCR MODE SET menu

is displayed. The arrow mark (√) is located in “Clock Set”.

4 Press the SHIFT√ button, the CLOCK SET menu is

displayed.

5 Press the SET – (or +) button to set the hours (eg :

09), then press the SHIFT√ button.

+ 17 hidden pages

Daewoo DT-K6623P-KS3 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual