Daewoo BM090, BS106, BH120E, BS090, BH090 User Manual

D1146

Primary filter:clean at every 5,000km,change at every 15,000km there

Change at every 20,000km.

166Page

Valve clearance Adjust at end of first 1,000km and every 20,000km there after. 171 Page
Air cleaner Clean at every 4,000km, change at every 12,000km there after. 176 Page
Transmission oil Change at end of first 5,000km and every 20,000km there after. 178 Page
Rear axle oil Change at end of first 5,000km and every 20,000km there after. 179 Page
Power steering oil Change at end of first 1,000km and every 24,000km there after. 180 Page
Power steering filter Change at end of first 1,000km and every 24,000km there after. 182 Page

IMPORTANT SERVICE ACTIVITIES

ҧAny failure resulting from a lack of normal maintenance as the maintenance service chart in this manual is not covered

by warranty.

CHECK ITEMS CHECK AND SERVICE INTERVALS PAGE

Engine oil 163 Page

Change : At end of first 1,000km,

long distance : every 30,000km
short distance : every 20,000km

D1146Ti
DE08TiS
DE12/T/Ti/TiS

Fuel filter

D1146
D1146Ti
DE12
DE12T
DE12Ti

Primary filter : clean at every 5,000km,

change at every 15,000km there after.

secondary filter : change at every 5,000km.

Engine oil filter Change with engine oil 164Page

DE08TiS
DE12TiS

Change : At end of first 1,000km,

High-speed, long distance : every 15,000km
In city, short distance : every 10,000km

This manual has been prepared to acquaint you with the operation and maintenance of your DAEWOO
BUSES and the provide important safety information. We urge you to read it carefully and follow the
recommendations to help assure the most enjoyable, safe and troublefree operation of your vehicle.

When it comes to service, remember that your DAEWOO dealer knows your vehicle best and is
interested in your complete satisfaction.

We would like to take this opportunity to thank you for choosing a DAEWOO product and assure
you of our continuing interest in your motoring pleasure and satisfaction.

This manual should be considered as a permanent part of your vehicle, and must remain with the
vehicle at the time of resale.

All information, illustrations and specifications contained in this manual are based on the latest product
information available at time of publication.
The right is reserved to make changes at any time without notice.

FOREWORD

1

1. IMPORTANT INFORMATIONŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 2

2. OPERATION AND CARE OF NEW VEHICLE

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 4

3. GETTING ON AND OFF, DRIVER’S SEAT AND BELT

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 6

4. INSTRUMENT, SWITCHES AND CONTROLS

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 14

5. DRIVING

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 135

6. INSPECTION AND MAINTENANCE

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 162

7. LUBRICATION

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 213

8. SCHEDULED MAINTENANCE SERVICE

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 221

9. TROUBLESHOOTING

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 225

10. MAIN DATA AND SPECIFICATION

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 234

11. BODY DIMENSION

ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 253

TABLE OF CONTENTS

2

IMPORTANT INFORMATION

LOCATION OF ENGINE NUMBER AND CHASSIS NUMBER

It is advisable to keep note of the engine number and chassis number as they are required when contacting your deal­er for repair services and parts order.

V.I.N plate

V.I.N(Vehicle identification Number)
plate is attached to the inner panel
above the front door.

Type A : Applicable for vehicles in

all countries except GCC
members.

V.I.N plate

V.I.N(Vehicle identification Number)
plate is attached to the inner panel
above the front door.

Type B : Applicable for vehicles in

GCC members.

Chassis number

The chassis number is stamped on
the upper face of the chassis frame
within the engine compartment.

3

Engine number Key

There are three types of key for the
bus ;

• Engine starting

• Mechanical locking for entrance
door (OPTION)

• Doors

– Entrance door operating
– Luggage doors (OPTION)
– Rear engine door (OPTION)
– Side engine doors (OPTION)
– Battery inspection door (OPTION)
–

Fuel tank inspection door (OPTION)

– Fuel inlet flap door (OPTION)

The keys are not interchangeable, but
door lock keys are interchangeable.
The code number of each key is
stamped on the key.
Record the key number and keep it
in a safe place.
In the event that the original key is
lost, duplicating can be done using
the key code information.

Engine No.

1378

4

OPERATION AND CARE OF NEW VEHICLE

It is important to observe the follow­ing precautions as operation and care
of the vehicle, particularly during the
break–in period have a strong influ­ence over the performance and ser­vice life of the vehicle.

1. Start and let the engine idle until
it becomes thoroughly warmed up
and coolant temperature increases
beyond 50°C (or 125°F) before
starting off.

2. Avoid racing the engine, abrupt
starts and hard stops.

3. Avoid over loading the vehicle dur­ing and after the break–in period.

Over loading

Over loading not only shortens the
service life of your vehicle but also
create serious potential safety haz­ards.

The weight of payload must be limit­ed within the GVW rating and distrib­uted over the front and rear axles so
as not to exceed the axle capacities.

Refer to “MAIN DATA AND SPECIFI­CATION” for GVW and Axle capaci­ty.

Maintenance

In order to maintain safe and depend­able vehicle operation, inspection and
adjustment should be performed as
outlined in “INSPECTION AND MAIN­TENANCE”.

Your DAEWOO dealer is willing to
perform regular maintenance opera­tion on your vehicle.

5

Engine oil change

Change engine oil filter catridge to new one at the
same time with engine oil.

Maximum engine speed

During the initial milage(Break–in period : 2,000km),
confine engine speed to 70% of the maximum and
scan the tachometer as you drive to prevent engine
over–running.
After the break–in period, increase the engine speed
gradually to complete running–in of the vital parts.

Engine Model Change Interval

D1146

At end of first 1,000km

D1146Ti

High–speed, long distance :
DE12Ti every 15,000km
DE12Ti In city, short distance :
DE12Ti every 10,000km

DE08TiS

At end of first 1,000Km

Long distance : every 30,000km
DE12TiS

short distance : every 20,000km

6

GETTING ON AND OFF, DRIVER’S SEAT AND BELT

DOOR OPENING AND CLOSING

(Applicable for vehicles in all
entrance door with mechanical key)

When opening the front door to get
in, first unlock the mechanical key on
the entrance door and operate the
entrance key on the right side of the
front middle panel.
When closing the front door to get
off, open the front door by operating
the door control switch and get off.

In the outside of bus, close the door
with the key and look the mechanical
key on the entrance door not to be
opened in case of air leaking.

(Applicable for vehicles in all
entrance door except mechanical key)

When opening the front door to get
in, operate the entrance key on the
right side of the froot middle panel.
When closing the front door to get
off, open the front door by operating
the door control switch and get off.
In the outside of bus, close the door
with the key.

I

D

L

I

N

G

H

.

.

L

Before operating entrance key, unlock
mechanical key on door frame.

NOTICE

When opening front entrance door for a long time, setting emergency valve
at manual position and put control switch in close position. When returning
to automatic condition, putting control switch and door in same condition
and set emergency valve at automatic position.

CAUTION

(Type A : Toggle switch) (Type B : One touch switch)

7

MANUAL OPENING AND
CLOSING

Type A : Select type

As setting the “Auto–Manual” change
lever installed right, lower inner side
of front panel(beside of driver’s right
leg), the door can be opened and
closed by hands.

Type B :

Push/Pull or rotary type (OPTION)

As setting the "Auto-Manual" change
knobs are installed two types. One of
the types installed inner upper panel
the entrance door operated by air.
Other installed outer mid panel on left
side of door operated by electric push
button. the door can be opened and
closed by hands.

I

D

L

I

N

G

H

.

.

L

(Push/Pull type) (Rotary type)

8

Adjustment of Fixed type (S-104H) (BM090, BS090)

1. Back angle adjustment
To adjust the seat back, turn No. 1 handle, and lean
backwards and foreward until desired angle is
achieved.

2. Slide adjustment
To move the seat forward and backward.
Pull No. 2 lever, forward and slide the seat.

3. Height (Tilting) adjustment
Desired the seal height can be achieved by puling
No. 3 lever upward and downward.

2

1

2

3

1

DRIVER’S SEAT AND BELT

9

How to use non suspension seat

Semi suspension seat can be infinitly adjusted to suit the weight of the driver.

Height Adjustment

Back Angle

Slide Adjustment

10

Adjustment of Air suspension type driver’s
seat (S-110A) (BS106, BH113/115/120E, BV120)

1. Slide adjustment
To move the seat forward or rearward, pull No. 1 lever
upwards and the slide the seat.

2. Back angle adjustment
To adjust the seat back, pull No. 2 lever and lean
backwards or forewards until the desired angle is
achieved.

3. Height and slope adjustment
Desired seat height can be achieved by pulling No. 3
lever.

4. Upper lumbar support air cushion adjustment.

4. Lower button is for inflation, upper button is for defl-

4. ation

5. Lower lumbar support air cushion adjustment.
Push the lumbar support air cushion adjustment but­ton to suit seating position.

4. Lower button is for inflation, upper button is for defl-

4. ation

6. Air suspension stroke support air undercushion adjust­ment

ř

Do not adjust the driver’s seat while driving.

Ś

2

2

4

4
5

3

3

6

1

5

4

1

Adjustment of Air suspension type driver’s seat (S-110A)
(BH090, BS106, BH115E, BH120E) (BM090/BS090 : OPTION)

11

How to use air suspension seat

Air suspension seat can be infinitly adjusted to suit the weight of the driver.

Height Adjustment Tilt Adjustment(RR) Tilt Adjustment(FRT) Back Angle

Lumbar Support(Lower)Lumbar Support(Upper)Slide Adjustment

12

The vehicle is equipped with three point type(driver’s)
and reel type(passenger’s)
Every person who drives or rides in this vehicle
should wear a seat belt at all time.
The buzzer will sound, if the driver’s seat belt is not
fastened when the ignition switch is turned to the
“ON” position.

1) Pull the belt evenly out of the retractor and guide
it across the body making certain that it is not
twisted.
The seatback should not be in a reclining position
anymore than needed for comfort.

2) Insert the metal latch plate ڹ into the buckle ں.

3) To remove the belt, depress the red push button
on the buckle.
And the belt wil roll up automatically.

4) When the driver’s seat belt is not in use, adjust
the latch plate ڹ within 10

cm

from the seat loop.

The belt must not be twisted when fitted.

Do not wear the shoulder belt across the neck or
under your outer arm.

Seat Belts

1

2

13

Seat belt warning lamp

The seat belt warning lamp comes on
when the ignition switch is placed in
the “ON” position unless the driver’s
seat belt is securely fastened.

Pilot indicator lamps

1. Never use the belt for more
than one person at a time.

2. Never wear the belts twisted.

3. Make sure seat belts or their
attachments not to be thrusted
in metal parts of the seat or
the door.

4. Seat belts should be adjusted
as firmly as possible.

5. Do not wear seat belts low
under your shoulder.

6. If you replace your seat belts
incorrectly, you may by injured
by hardware of the belts at
sudden stops.

7. Do not wear your seat belts
with hard or breakable objects
such as glasses, pens, etc. put
into the pocket of your upper
garment.

NOTICE

1. Periodically inspect all parts of
the belts and replace any dam­aged parts.

2. Make sure that the belts are
not to be damaged by sharp
edged objects.

3. The belts should be changed if
webbing has become frayed or
damaged.

4. Check if fixing bolts have been
firmly installed to the floor.

5. Always keep the seat belts
clean and dry.

6. Clean only with tepid soapy
water.

7. Do not bleach or dye seat
belts.

CAUTION

14

INSTRUMENTS, SWITCHES AND CONTROLS

11

18

202223

24

27

26

30

29

25

56798

21

13 17

10

1
2
3

4

14

19

15

32

12

31

28

15

ҧThe quantities or locations of switches could be different from the figure, because the switches could be added or

omitted, or locations could be changed by the requirements of customers.

LEGEND OF INSTRUMENT PANEL AND OTHER DEVICES

No. Description No. Description No. Description

1 Voltage meter
2

Engine coolant temperature gauge
3 Fuel gauge–Engine
4 Engine oil pressure
5 Air pressure gauge
6 Upper pilot lamps
7 Engine RPM gauge
8 Lower pilot lamps
9 Tachograph (OPTION)

Speedometer (OPTION)

10 Door opening switch (FRT)

11 Door opening switch(MID) (OPT)
12 Microphone stand
13 Radio & Cassette player
14 Switches
15 Door opening switch(RR) (OPT)
17 Defroster controller
18 Engine idling knob
19 Shift lever

(Except auto transmission)
20 Accelerator pedal
21 Wiper control and exhaust

brake lever

22 Brake pedal
23 Horn switch
24 Bulb check
25 Steering wheel
26 Head & Direction lamp lever
27 Clutch pedal
28 Valve–cab control
29 Clutch oil reservoir
30 Control panel (OPTION)
31 Door controller
32 Cup holder (BM090, BS106)

16

ATTACHMENTS OF STEERING COLUMN

Steering wheel and horn button

The steering wheel should not be
turned while the vehicle is stationary
as it adversely affects the tires and
steering system.
Horn button is equipped on the mid­dle of steering wheel.

Steering wheel adjustment

Type A : Tilt & Telescopic
(BH115E,BH120E)
(BM090/BS090/BS106 : OPTION)

Adjust the steering wheel to the
desired position after pulling lock
lever.

Adjusting angle : 8°
Travel : 40mm

Type B : Fixed (BM090, BS106)

Starter switch

Starter switch operates in the 4
stages as follows :
ҮLOCK : The key can be inserted or

removed only when the switch is in
this position.

ҮACC : This position turns on the

radio, digital clock, cigarette lighter
and consent.

unlock

3°

5°

lock

20mm
20mm

17

ҮON : This position turns on the

electrical equipment. During the
vehicle operation, hold the key in
this position.
ҧWhen the key is in “ON” position,

the engine is automatically pre­heated according to outdoor tem­perature. Pre–heater warning
lamp blinks for 0.3 second at a
higher temperature(coolant temp. :
above 25°

C

) and for 18 seconds
at a lower temperature(coolant
temp

.: below 25°

C

), during
which the engine is preheated for
20 seconds.

ҮSTART : Once the engine is start-

ed, it is preheated automatically
according to outdoor temperature
(until coolant temperature becomes
25°

C

or up to 6 minutes). This

improves the engine condition.

Turn signal switch

Move this combination switch lever in
the desired direction so that the cor­responding turn signal lamp operates
and causes the turn signal indicator
lamp on the instrument panel to flash.
The switch lever returns automatical­ly to the neutral position when the
steering wheel is returned to the
reverse direction. When head lamp
switch is in 2nd stage simultaneously
with turn signal lamp “ON”, cornering
lamp also comes on.

LOCK

ACC

ON

START

Pilot indicator lamps

Ү

Once the engine started,
release the key immediately.

Ү

Do not exceed 10 seconds for
the operation of starter.

Ү

Gearshift lever should be in
neutral position when attempting
to start the engine.

CAUTION

18

High beam switch

When the head lamps are on, pulling
the lever down lights up not only the
head lamps with high beam but also
the high beam indicator lamp. When
pulling it up, head lamps with low
beam are on.

Passing lamp switch

To light up passing lamps at any
time, pull up the lever towards the
steering wheel.
The lever will return to the OFF posi­tion when released.

Lamp switch(turn type)

Lamp switch operates in two stages
as follows :
1st stage : tail lamp, license plate

lamp, instrument panel
lamp, clearance lamp

2nd stage:tail lamp, license plate

lamp, instrument panel
lamp, clearance lamp,
head lamp, cornering
lamp(simultaneously with
turn signal lamp “ON”)

Windshield wiper switch

The windshield wiper switch has 3
positions to control the windshield
wiper.

1. OFF ˞ Off

2. INT ˞ Intermittent wipe

3. LO ˞ Continuous wipe, slow speed

4. HI ˞ Continuous wipe, fast speed

high beam

(passing)

high beam

low beam

2nd stage

1st stage

OFF

1

2

3

4

Do not operate the wipers when the
windshield remains dry. They may
scratch the windshield glass. Do not
operate the wipers if they are cov­ered with snow or ice as this may
damage the wiper system.

NOTICE

19

Wiper speed control switch

The desired intermittent operation
time can be controlled by turning the
knob when the wiper switch is in
“INT” position.

Windshield washer switch

To let washer fluid spray on the wind­shield, press and hold the center but­ton of switch.
And the windshield wipers are simul­taneously operated for 2–3 cycles.

Exhaust brake switch

The exhaust brake system is
designed to shut off exhaust pipe
when the engine brake is applied,
resulting in assisting brake action.
When the switch lever is pushed
downward, and clutch and accelerator
pedals are released, the indicator
lamp comes on showing that the
exhaust brake is in operation. When
the clutch and accelerator pedals are
depressed, the exhaust brake stops
working.

Hazard warning flasher switch

When the right–hand lever is pushed
upward, all the turn signal lamps are
made to flash regardless of the turn
signal switch position.
The hazard warning flasher switch is
to be used when your vehicle gets in
a traffic hazard or is parked in the
darkness.

20

PERIPHERAL DEVICES OF STEERING COLUMN

Idle control knob
(Except MT643 auto T/M)

Turning the knob clockwise after cold
starting of the engine will increase
idling speed and thus facilitate quick
normalization of the engine coolant
temperature.
Always drive with the knob turned
back home.

Idle control valve
(For MT643 auto T/M)

Valve position

• FAST IDLE (UP) : 900~1000rpm.

• IDLE (DOWN) : 550~650rpm.

Battery switch

It controls the entire electrical cir­cuits with the exception of parking
lamps, hazard warning flashers. The
electrical circuits are energized when
the battery main switch is pressed.

I

D

L

I

N

G

H

.

.

L

ascending

position

IDLE

FAST
IDLE

Do not use this knob to stop the
engine.

NOTICE

21

Door opening switch

The entrance door is operated by the
air cylinders as the door opening
switches on.

Manual door opening switch

When the manual door opening
switch is placed at “auto” position, the
doors are operated by the door open­ing switches, or when the switch is
placed at “manual” position, the doors
are not operated by the door opening
switch and can be opened or closed
by the hands.

Air parking brake switch

When the switch is pushed, the park­ing brake is actuated and the indica­tor lamp comes on. pushed one more
the switch, releases the brake. Make
sure that the indicator lamp is off
before driving off.

I

D

L

I

N

G

H

.

.

L

(Toggle switch type)

I

D

L

I

N

G

H

.

.

L

Type A : Cab control valve

Type B : Gradual control

22

ABS/ASR check switch(OPTION)

The switch used for self Diagnosis of
ABS/ASR system.
It needs for a car mechanics, but not
used for a driver usually, push the
button about 3 seconds, self diagno­sis started and the ABS/ASR warning
lamp blinker on instrument panel.

ABS ARS

ABS

ABS ARS

ASR

POWER

POWE

R

A

I

R

C

O

ND

I

TI

O

N

ER

POWER

A

UT

O

V

E

N

T

IL

A

T

O

R

A

I

RC

OND

I

T

I

O

N

E

R

1

2

3

4

23

Engine check / clear switch
(For DE12TiS ENG.)

When engine malfunction pilot lamp
comes on, follow the below procedure
to solve the problem.

1. To check error type pressing
engine check switch.
With pressing this switch, engine
malfunction lamp blinkers accord­ing to the error types.

(Example)

Error code 12 : prestroke control error

ҮError code

1. Engine check switch (Blue color)

2. Engine clear switch (Black color)

2. After repairing defects according to
the engine maintenance manual,
press the engine clear switch for
5seconds to remove the errors on
ECU.

Pilot indicator lamps

CHECK

ENGINE

CHECK

ENGINE

CLEAR

1 2

ON

OFF

Malfunction
Pilot lamp

No. Defects

01 Normal
12 Prestroke control error
13 Prestroke sensor error
14 Prestroke offset error
15 Prestroke actuater power error
16 Engine rpm sensor error
21 Coolant temp. sensor error
22 Fuel rack sensor error
23 Air heater relay error

24

INSTRUMENTS AND INDICATOR LAMPS

1. Voltmeter

2. Engine coolant temperature gauge

3. Fuel gauge

4. Engine oil pressure gauge

5. Air pressure gauge

6. Engine tachometer
(If the engine RPM indicating func­tion is included in tachograph, this
gauge is substituted to blank cover.)

7. Tachograph
(BH115E, BH120E)
(BM090/BS106 : OPT)
Speedometer (BM090, BS106)

8. Bulb check switch

9. Cover

10. Turn signal/hazard warning indicator

11. Upper pilot indicator lamps

12. Lower pilot indicator lamps

32

24
16
0

0

4

8

C

H

E

F

0

1

2

3

x1000rpm

0

3

6

9

12

15

kg/cm

A I R

2

7101112

3458129 6

7

0

20

40

60

80

100

120

140

160

Km/h

0000000

Tachograph

Speedometer

0

80

000000

km/h

60

40

20

160

140

120

100

25

Voltmeter

The voltmeter indicates the battery
condition. Check the voltmeter read­ing with the engine running. The
gauge needle should stand between
the reading of 24 and 28.

Temperature gauge

The gauge indicates the engine
coolant temperature. If the gauge
needle stands below the red colored
zone, it means that engine coolant
temperature is normal.

If the needle stands in “H”(overheat­ing), stop the vehicle and run the
engine at a moderately fast idle
speed or put the gear in lower posi­tion to reduce engine load. If the
vehicle is operated in abnormal con­dition, engine performance will be
reduced and fuel consumption will be
increased.

Fuel gauge

This gauge indicates fuel level of the
fuel tank all the time regardless of the
starter switch position.

The capital letter “E” represents
almost “empty”. Top–up the fuel tank
before the gauge indicates “E”.

32

24

16

0

C

H

E

F

26

Oil pressure gauge

This gauge indicates oil pressure in
the engine lubricating system. The
indication of the gauge should be 1–3
kg/cm2when the engine is at idle ; it
should be 3–6.5

kg/cm2when the
engine is running at medium speed.
When the gauge needle does not
move upward at all or hydraulic pres­sure changes abruptly, check the oil
level in the engine crankcase. If the
oil level is found normal, have the
hydraulic system checked by your
nearest Daewoo dealer.

Do not run the engine with low oil
pressure indication.

Air pressure gauge

Air pressure gauge indicates air pres­sure in the air tanks. While driving,
the gauge needle must be within the
range of 5.3–8.2

kg/cm2.

Be habitual of watching the gauge,
while driving, to make sure the gauge
needle indicates the normal condi­tions.

Engine tachometer

The tachometer indicates the engine
speed in revolutions per minute(rpm)
and red colored zone represents
critical engine speed.

Excessively high engine rpm(red col­ored zone) may cause damage to the
engine.
To drive economically, keep the
engine within 1,000Ŕ2,000rpm.

Maximum allowable engine speed :
D1146 ENG : 2,500rpm.
D1146Ti/DE12/DE12T ENG.

: 2,200rpm.
DE08TiS ENG : 2,300rpm.
DE12Ti/DE12TiS ENG.:2,100rpm

1

4

8

0

3

6

9

12

15

kg/cm

A I R

A

O

H

A

I

R

F

U

L

L

A

I

R

2

0

1

2

3

x1000rpm

If the gauge needle stands in the
red zone, warning lamp comes on
and alarm buzzer sounds. Imme­diately stop the vehicle, check for
unusual conditions, run the engine
at a moderately fast idle speed to
increase air pressure, then drive off.

NOTICE

27

Tachograph
(BH115E, BH120E)
(BM090/BS090/BS106 : OPT)

The tachograph is consisted of odo­meter and clock. The vehicle speed
and running distances are registered
in a single chart. The speedmeter
indicates the vehicle speed in kilome­ter per hour(

km/h

). The odometer indi­cates individual trip distances. The
odometer records the total distance in
km

. The unit of registered distance is
loom.
For further information refer to
“TACHOGRAPH” on page.

Speedometer (BM090, BS106)

The speedometer is consisted of
odometer and clock. The vehicle
speed and running distances are reg­istered in a single chart. The speed­meter indicates the vehicle speed in
kilometer per hour(

km/h

). The odome­ter indicates individual trip distances.
The odometer records the total dis­tance in

km

. The unit of registered

distance is loom.

For further information refer to
“SPEEDOMETER” on page.

Bulb check switch

When bulb check switch is pressed,
warning lamp on instrument panel
comes on.
And also the warning buzzer sounds.

Before driving, use this switch to
check that all warning lamps includ­ing speed indicator lamps and their
circuits are operating normally.

7

0

20

40

60

80

100

120

140

160

Km/h

0000000

0

80

000000

km/h

0-80 101-160

81-100

60

40

20

160

140

120

100

32

24
16
0

0

4

8

C

H

E

F

0

1

2

3

x1000rpm

0

3

6

9

12

15

kg/cm

A I R

2

SPEED

T/M

SAFETY

ABS ASR

E

28

Turn signal indicator lamp

When the turn signal switch or haz­ard warning flasher switch is turned
on, the turn signal indicator lamp
flashes to indicate the operation of
the external turn signal lamps or haz­ard warning flashers.