Daewoo 720D, 905DS, 905D, 905DF Service Manual

D AEW OO ELECTR ONICS CO., LTD.

http : //svc.dwe .co.kr

Service Manual

XGA COLOR MONITOR

Model : 720D

905D

905DS

905DF

January, 2001

CONTENTS

SAFETY PRECAUTIONS 1
GENERAL SAFETY INFORMATION 2
SERVICING PRECAUTIONS 3
TECHNICAL INFORMATION 6
GENERAL INFORMATION 7
PIN CONNECTOR 8
CAUTIONS FOR ADJUSTMENT AND REPAIR 8
OPERATION AND ADJUSTMENT 9
ALIGNMENT PROCEDURE 13
TROUBLESHOOTING HINTS 15
BLOCK DIAGRAM 30
PCB LAYOUT 31
SCHEMATIC DIAGRAM 36
EXPLODED VIEW & MECHANICAL PARTS LIST 40
INFORMATION OF PART DESCRIPTION 44
ELECTRICAL PARTS LIST 45

1

SAFETY PRECAUTIONS

◆ Safety Check

Care should be taken while servicing this analog color display because of the high voltages used in the
deflection circuits. These voltages are exposed in such areas as the associated flyback and yoke circuits.

◆ Fire & Shock Hazard

• Insert an isolation transformer between the analog color display and AC power line before servicing the
chassis.

• When servicing, pay close attention to the original lead dress especially in the high voltage circuit area;
if a short circuit is found, replace all parts which have been overheated as a result of the short circuit.

• All the protective devices must be reinstalled per original design.

• Soldering must be inspected for possible cold solder points, frayed leads, damaged insulation, solder
splashes or sharp solder points. Be certain to remove all foreign materials.

◆ Implosion Protection

Picture tube in this monitor employs intergral implosion protection system, but care should be taken to
avoid damage and scratching during installation.
Only use same type replacement picture tubes.

◆ X-Ray

IMPORTANT SAFETY NOTICE: There are special components used in this analog color display,

which are important for safety. These parts are shaded on the
schematic diagram and on the replacement parts list. It is essential
that these critical parts should be replaced with manufacturer’s
specified parts to prevent X-Ray, shock, fire or other hazards. Do
not modify the original design without getting written permission
from DAEWOO ELECTRONICS CO. or this will void the original
parts and labor warranty.

CAUTION: No modifications of any circuits should be attempted. Service work should be performed

only after you are thoroughly familiar with all of the following safety checks and servicing
guidelines.

WARNING: The only potential source of X-Ray is the picture tube. However when the high voltage

circuitry is operating properly, there is no possibility of an X-Ray problem. The basic
precaution which must be exercised is to keep the high voltage at the following factory
recommended level.

NOTE: It is important to use an accurate, periodically, calibrated high voltage meter.

• To measure the high voltage, use a high-impedance high-voltage meter.
Connect(-) to chassis and (+) to the CRT anode button.

• Turn the Contrast & Brightness Control fully counterclockwise.

• Measure the high voltage. The high voltage meter should indicate the following factory

recommended levels.

• If the upper meter indication exceeds the maximum level, immediate service is required to

prevent the possibility of premature component failure.

• To prevent X-Ray possibility, it is essential to use the specified picture tube.

• The normal high voltage is 25.5KV or below and must not exceed 29KV at zero beam current

at rated voltage.

2

GENERAL SAFETY INFORMATION

Warning:This product includes critical mechanical and electrical parts which are essential for x ray

protection. For continued safety, replace critical components that are indicated in the service

manual with exact replacement parts given in the parts list.
Operating high voltage with this product is 29Kv at minimum brightness. Refer to service
manual for measurement procedures and proper service adjustments.

◆ Terms in the manual

CAUTION Statements identify conditions or practices that could result in damage to the equipment or

other property.

WARNING Statements identify conditions or practices that could result in personal injury or loss of

life.

◆ Terms as marked on equipment

CAUTION Statements indicate a personal injury hazard not immediately accessible as one reads the

marking or a hazard which is properly included on the equipment itself.

WARNING Statements are clearly concerning indicated personal injury hazards.

◆ Symbols in the manual

The symbols indicate where applicable cautionary or other information is to be found.

◆ Symbols as marked on equipment

Protective GROUND terminal

◆ High Voltage Warning And Critical Component Warning Label

The following warning label is on the CRT PWB shield case inside the unit.

3

SERVICING PRECAUTIONS

◆ General Servicing Precautions

1. Always unplug the AC power cord from the AC power source before:
a. Removing or reinstalling any component, circuit board, module, or any other instrument assembly.

b. Disconnecting or reconnecting any electrical plug or other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic capacitor in the instrument.

d. Discharging the picture tube anode.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage

measuring device (DVM, FETVOM. etc.) equipped with a suitable high voltage probe. Do not test high
voltage by “drawing an arc”.

3. Discharge the picture tube anode only by: (a) first connecting one end of an insulated clip lead to the

degaussing or line grounding system shield at the point where the picture tube socket ground lead is
connected, and then (b) touching the other end of the insulated clip lead to the picture tube anode
button, using an insulating handle to avoid personal contact with high voltage.

4. Do not any spray chemicals on or near this instrument, or any of its assemblies.

5. Unless otherwise specified in this service manual, only clean electrical contacts by applying the

following mixture to the contacts with a pipe cleaner, cotton-tipped stick, or comparable nonabrasive
applicator: 10% (by volume) Aceton and 90% (by volume) isopropyl alchohol (90%-99% strength).

6. Do not damage any plug/socket B+ voltage interlocks with which instruments covered by this service

manual might be equipped.

7. Do not apply AC power to this instrument and/or any other of its electrical assemblies unless all the

solid-state device heat sinks are correctly installed.

8. Always connect the test instrument ground lead to the appropriate instrument chassis ground before

connecting the test instrument positive lead. Always remove the test instrument ground lead last.

9. Only use the test fixtures specified in this service manual with this instrument.

CAUTION: Before servicing instruments covered by this service manual, its supplements, and

addendum, please read and follow the SAFETY PRECAUTIONS of this manual.

NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any

of the safety precautions on page 1 of this manual, always follow the safety precautions.

Remember: Safety First.

CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors

may result in a explosion.

CAUTION: This is a flammable mixture. Unless specified in this service manual, lubrication of

contacts is not required.

CAUTION: Do not connect the test fixture ground strap to any heatsink in this instrument.

4

◆ Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity.
Such components are commonly called Electrostatically Sensitive (ES) Devices.
The typical examples of ES devices are integrated circuits, some field-effect transistors, and
semiconductor “chip” components. The following techniques should be used to help reduce the incidence
of component damage caused by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly,
wipe off any electrostatic charge on your body by touching any known earth ground. Alternatively,
obtain and wear a commercially available discharging wrist strap device which should be removed for
potential shock reasons prior to applying power to the unit under testing conditions.

2. After removing the electrical assembly equipped with ES devices, place the assembly on a conductive
surface such as aluminum foil to prevent electrostatic charge buildup or exposure to the assembly.

3. Only use a grounded-tip soldering iron to solder or unsolder ES devices.

4. Only use an anti-static type solder removal device. Some solder removal devices not classified as “anti­static” can generate enough electrical charges to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate enough electrical charges to damage ES

devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are
ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together
by conductive foam, aluminum foil, or comparable conductive material).

7. Immediately before removing the protective material from the leads of replacement ES devices, touch
the protective material to the chassis or circuit assembly into which the device will be installed.

8. Minimize bodily movements when handling unpackaged replacement ES devices. (Otherwise harmful
motion such as the brushing together clothes fabric or the lifting your foot from a carpeted floor can
generate enough static electricity to damage ES devices).

◆ General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron with appropriate tip size and shape that will maintain
tip temperature between a 550°F-660°F (288°C-316°C) range.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean.

4. Throughly clean the surface to be soldered. Use a small wire-bristle (0.5 inch or 1.25cm) brush with a
metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following soldering technique:
a. Allow the soldering iron tip to reach normal temperature (550°F to 660°F or 288°C to 316°C)
b. Hold the soldering iron tip and solder strand against the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil,

and hold it there until the solder flows onto and around both the component lead and the foil.

d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle

brush.

CAUTION: Be sure that no power is applied to the chassis or circuit, and observe all other safety

precautions.

5

FIGURE 1. USE SOLDERING IRON TO PRY LEADS

◆ IC Removal/Replacement

Some utilized chassis circuit boards have slotted (oblong) holes through which the IC leads are inserted
and then bent flat against the circuit foil. When holes are slotted, the following technique should be used
to remove and replace the IC. When working with boards using the familiar round hole, use the standard
technique as outlined in paragraphs 5 on the page under the title of general soldering guidelines.

◆ Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the
soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with
desoldering braid before removing the IC.

◆ Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (lt is not necessary to reapply acrylic coating
to the area).

◆ “Small-Signal” Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend the ends of each of three leads remaining on the circuit board into a “U” shape.

3. Bend the replacement transistor leads into a “U” shape.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board
and crimp the “U” with long nose pliers to ensure metal-to-metal contact, then solder each connection.

◆ Power IC, Transistor or Devices Removal/Replacement

1. Heat and remove all solders from the device leads.

2. Remove the heatsink mounting screw (if applicable).

3. Carefully remove the device from the circuit board.

4. Insert new device in circuit board.

5. Solder each device lead and then clip off excess lead.

6. Replace heatsink.

6

TECHNICAL INFORMATION

◆ Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicularly to the circuit board.

3. Observing diode polarity, wrap each lead out of the new diode around the corresponding lead on the
circuit board.

4. Securely crimp each connection and solder it.

5. Inspect the solder joints of the two “original” leads on the circuit board copper side. If they are not
shiny, reheat them and apply additional solder if necessary.

Model Names 720D 905D
CDT Size 17-inch 19-inch
Diagonal visible image area 16.2-inch 18-inch
Dot Pitch 0.26 mm
Synchronization Horizontal 30 - 95 KHz

Vertical 50 - 160 Hz
Plug and Play DDC1/2B/CI
Power Saving EPA, VESA DPMS, Nutek Compliant
Power Source 100-240 Vac, 50/60Hz (Free Voltage)
Power Consumption 80 W 90 W
Dimension-W x H x D 420 x 440 x 440mm 466 x 475.5 x 464.5mm
(set with stand)
Weight-unpacked (lbs/Kg) 35.7/16.2 41.9/19.0
Operating Temperature 10 ~ 40°C /50 ~ 104°F

Model Names 905DS 905DF
CDT Size 19-inch Short length 19-inch DynaFlat
Diagonal visible image area 18-inch 18-inch
Dot Pitch 0.26 mm 0.25 mm
Synchronization Horizontal 30 - 95 KHz

Vertical 50 - 160 Hz
Plug and Play DDC1/2B/CI
Power Saving EPA, VESA DPMS, Nutek Compliant
Power Source 100-240 Vac, 50/60Hz (Free Voltage)
Power Consumption 90 W
Dimension-W x H x D 466 x 475.5 x 408.5mm 466 x 475.5 x 465mm
(set with stand)
Weight-unpacked (lbs/Kg) 44.0/20.0 47.3/21.5
Operating Temperature 10 ~ 40°C /50 ~ 104°F

7

GENERAL INFORMATION

This color monitor automatically scans all horizontal frequencies from 30KHz to 95Hz, and all vertical
frequencies from 50Hz to 160Hz. This color monitor adopted the OSD (On Screen Display), it shows the
sync polarity and frequency and it provides that easily adjust control. This color monitor supports IBM PC,
PC/XT, PC/AT, personal System/2 (PS/2), Apple Macintosh, and compatible users crisp text and vivid color
graphics display when using the following graphics adapters : (VGA, 8514/A, Super VGA, VESA and XGA
and Apple Macintosh Video Card). And so, this color monitor has a maximum horizontal resolution of 1600
dots and a maximum vertical resolution of 1200 lines for superior clarity of display.

By accepting analog signal inputs which level is zero to 0.7 Volts. This color monitor can display and
unlimited palette of colors depending on the graphics adapter and software being used.

◆ Abbreviations

ADJ Adjustment
AFC Automatic Frequency Control
CRT Cathode Ray Tube
Def Deflection
D.Y Deflection Yoke
HVG High Voltage Generator
H.SYNC Horizontal Synchronization
OSC Oscillator
P.S.U Power Supply Unit
PWA Printed Circuit Board Wiring Assembly
R.G.B Red, Green, Blue
V.Sync Vertical Synchronization

8

PIN CONNECTOR

CAUTIONS FOR ADJUSTMENT AND REPAIR

• Degaussing is always required when adjusting purity or convergence.

• The white balance adjustment has been done by a color analyzer in factroy. The adjustment procedure,
described in the service manual is made by a visual check.

• Allow 20 minutes warm-up time for the display before checking or adjusting only electrical
specification or function.

• Reform the leadwire after any repair work.

◆ Caution For Servicing

• In case of servicing or replacing CRT, high voltage sometimes remains in the anode of the CRT.
Completely discharge high voltage before servicing or replacing CRT to prevent a shock to the
serviceman.

Arrangement of 15-pin D-sub connector

Pin Signal

1 Red
2 Green
3 Blue
4 GND
5 GND
6 GND - Red
7 GND - Green
8 GND - Blue
9

+5Vdc

10 GND - H.Sync
11 GND - V.Sync
12 Bi-directional Data (SDA)
13 Horizontal Sync
14 Vertical Sync (VCLK)
15 Data Clock (SCL)

1

6

15

10

9

OPERATION & ADJUSTMENT

Control Panel

• Move cursor to the right window on the OSD window.

• Increase the value of any selected function.

• Move cursor to the left window on the OSD window.

• Decrease the value of any selected function.

• Launch OSD(On-Screen Display) MENU window.

• Move cursor to the high window on the OSD window.

• Increase the value of V.size or V.center.

• Move cursor to the low window on the OSD window.

• Decrease the value of V.size or V.center.

10

Key Process

OSD OFF

MENU

MENU

MENU

MENU

•

When you choose the icon on the OSD window, you can exit the OSD screen.

Hot Key

BRIGHTNESS CONTRAST

11

Adjust the width (horizontal size) and the height (vertical size) of the display.

H. SIZE &

V. SIZE

H. LINEARITY

V. LINEARITY

Adjust the horizontal linearity.

Adjust the vertical linearity.

Select language for OSD (5 languages).

LANGUAGE

Adjust the position of the display horizontally(left or right) and vertically (up or
down).

H. CENTER &

V. CENTER

Choose different preset color temperatures or set your own customized color
parameters.

Adjust the red gain.

Adjust the green gain.

Adjust the blue gain.

COLOR TEMP

RED GAIN

GREEN GAIN

BLUE GAIN

Adjust the red bias.

Adjust the green bias.

Adjust the blue bias.

RED BIAS

GREEN BIAS

BLUE BIAS

ICON CONTROL FUNCTIONS

OSD Functions

Adjust the vertical picture moire cancellation.

V. MOIRE

Adjust the focus image.

FOCUS

ZOOM

Adjust the display width & height at the same time.

Adjust the horizontal picture moire cancellation.

H. MOIRE

12

Adjust the parallelogram when the screen is leaning left or right.

Adjust the rotation when the screen is tilted left or right.

Adjust the pin corner top when the top sides of the screen are bowed.

ROTATION

T. PIN
CORNER

PARALLELOGRAM

Adjust the trapezoid of the screen by moving the lines inward or outward.

Adjust the side balance when the sides of the screen are bowed towards left or
right.

PIN BALANCE

TRAPEZOID

Adjust the pin corner bottom when the bottom sides of the screen are bowed.

B. PIN
CORNER

Degauss the display and restore image quality.

DEGAUSS

Reset the screen to the Factory Preset Display Settings.

Display a RGB Color Bar to determine whether the screen color is expressed
normally or not.

TEST PATTERN

RECALL

Display horizontal & vertical frequency and polarity.

STATUS

POWER SAVER

YES : VESA DPMS operation.
NO : NO DPMS operation.

ICON CONTROL FUNCTIONS

Adjust the left and right margins for more convex or more concave margins.

PINCUSHION

13

◆ Standard Adjustment Conditions

1. Power source voltage : AC 100 - 240Vac, 50/60Hz.

2. Aging : Take at least 15 minutes warm-up time.

3. Signals.

Video : Analog 0.7Vpp 75Ωterminal positive polarity
Synchronizing : Composite H+V Sync : 1.0Vpp ~ 5.0Vpp (Positive / Negative)

Separate H, V Sync : TTL Level (Positive / Negative)

Deflection frequency

Horizontal Frequency : 30KHz - 95KHz
Vertical Frequency : 50Hz - 160Hz

◆ Main Adjustment

1. Setting the Controls
Set contrast and brightness in Control Menu unless otherwise specified.

Contrast : Max.
Brightness : Center

2. H. Size, H. Center, V. Size, H. Center, Side Pincushion, T. Pin Corner, B. Pin Corner, Trapezoid,

Parallelogram, Rotation, Pin Balance, H. Linearity, V. Linearity

Receive the cross hatch pattern of Factory preset mode.
H. Size, H. Center, V. Size, H. Center, Side Pincushion, T. Pin Corner, B. Pin Corner, Trapezoid,
Parallelogram, Rotation, Pin Balance, H. Linearity, V. Linearity controls are adjusted at each mode.
In Factory, Auto Alignment was done at each mode. Therefore, Factory preset mode have their own
value according to each control.

3. Focus
(a) Set brightness control to center and contrast control to Maximum.
(b) Receive all “H” character pattern of 91KHz mode signal.
(c) Adjust the Static Focus VR to obtain best H.Focus.
(d) Adjust the Dynamic Focus VR to obtain best V.Focus.
(e) If the H/V Focus is not satisfactory, readjust the Static / Dynamic Focus.

4. White Balance Adjustment

(a) Select 9300°K on the OSD Menu.
(b) Receive a full white pattern of 91KHz mode signal by using the signal generator.
(c) Set the brightness control to 80 and the contrast control to maximum.
(d) Cut off the HVG screen VR.
(e) Receive all the black patterns. The luminance of the screen should be 0.2 ± 0.03 Ft-L by using

Screen VR.

(f) Select the R-BIAS, G-BIAS and B-BIAS on the control menu and adjust the / key to get the

color coordinates in x=0.281 ± 0.015, y=0.311± 0.015.
(g) Receive a small block pattern. Adjust the brightness value to the center.
(h) Select the R-GAIN and B-GAIN and adjust the / key to get the color coordinates in x=0.281 ±

0.015, y=0.311 ± 0.015.
(i) Adjust the ABL(at the OSD) control to get the screen luminance to 40 Ft/L (a small block pattern).
(j) Receive a full white pattern. Adjust VR581(Sub-contrast) to get the screen luminance to 30 Ft-L.

Check if the x, y coordinates of color analyzer is in x=0.281±0.015, y=0.311±0.015. If the color
coordinates is out of range, adjust the R. G. B BIAS & GAIN to get the coorinates in x=0.281,
y=0.311. Make sure that the coordinates is in the appropriate range.

(k) Select 6550°K on the OSD Menu and set the color coordinates in x=0.313, y=0.329 at the

maximum contrast control and center brightness control

(l) Check if a full white pattern is over 30Ft/L.

ALIGNMENT PROCEDURE

14

5. Static Convergence Adjustment
(a) Apply a magenta cross hatch pattern on display.
(b) Adjust the focus from the best over all focus on the display.

Also adjust the brightness to the desired condition.

(c) Vertical red and blue lines are converged by varying the angles between the two tabs of the 4-pole

magnets.

(d) Horizontal red and blue lines are converged by varying the tabs together and keeping the angle

between them constant.
(e) Apply a yellow cross hatch pattern on the display.
(f) Vertical green and red lines are converged by barying the angle between the two tabs of the 6-pole

magnets.

(g) Horizontal green and red lines are converged by varying the tabs together and keeping the angle

between them constant.

15

TROUBLESHOOTING HINTS

1. No Character

16

2. No Raster

17

3. A missing Color

18

4. Abnormal OSD Font

19

5. Horizontal Output Circuit

MODE SCAN B+

VGA (31.5KHz) 43V

43KHz 60V
68KHz 97V
79KHz 112V
91KHz 127V

20

6. Unstable Picture

6-1. Horizontal

21

6-2. V.OSC/Deflection Circuit

22

7. Focus

23

7-1. Dynamic Focus

FvH Fvv

720D : 300V 140V
905D : 320V 180V
905DS : 400V 200V
905DF : 350V 170V

24

8. Convergence

25

9. Abnormal Picture

9-1. Horizontal Size

* At first, adjust controls in the OSD Menu

MODE Scan B+

VGA 43V
43KHz 60V
68KHz 97V
79KHz 112V
91KHz 127V

* The B+ are as follows:

26

9-2. Vertical Size

27

10. High Voltage Output Circuit

Ω

∞

28

11. Power Supply Unit (P.S.U)

Replace R025

29

30

BLOCK DIAGRAM

HVG

(PHILIPS)

VIDEO D-SUB

RGB H/V

VIDEO PRE AMP

LM1253A(NS)

VIDEO OUT AMP

LM2453(NS)

HV DRIVE

/ CONTROL

MCU

MC68HC908BD48

(MOTOLORA)

H/V OSC Processor

TDA4856

(PHILIPS)

Geometrical

Compensatio

H-Driver

Drive

Transformer

H/V Moire

Cancellation

USB-PORT

1 Up Stream

4 Down Stream

AC INPUT

SMPS

Transformer

H/Def Output

TR/Damper

C/S Switching

2SC5411

DD54RC

(TOSHIBA)

Auto

H/Linearity

OP-Amp

V-Driver

KA2142

(SAMSUNG)

IIC

Control

PWM

D/A

CRT

SOCKET

FOCUS-UNIT

FBT

IIC

Control

DYNAMIC

FOCUS

190V

80V

+14V

-14V

HT

5V

FOCUS

OUTPUT

C5042F

(SAMSUNG)

31

PCB LAYOUT

720D/905D/905S/905DF Main PCB Component Side

32

720D/905D/905S/905DF Main PCB Solder Side

33

720D/905D/905S/905DF CRT PCB Component Side

720D/905D/905S/905DF CRT PCB Solder Side

34

905D/905DS Control PCB Component Side

905D/905DS Control PCB Solder Side

35

905DF Control PCB Component Side

905DF Control PCB Solder Side

36

SCHEMATIC DIAGRAM

Power or Connection Section

37

Control & Vertical Section

38

Deflection & Hige Voltage Section

39

Video Section

40

EXPLODED VIEW & MECHANICAL PARTS LIST

720D

905D

41

42

905DS

43

905DF

44

RESISTOR Description

Example:

CAP ACITOR Description

Example:

Fig &

Part No Description

Index

Capacitors
C102 CCXF1H104Z Ceramic 50V 0.1µF Z
C402 CCXB1H331K Ceramic 50V 330PF K
C105 CMXM 2A224J MYLAR 100V 0.22µF J

Allowance
C ± 0.25pF
D ±0.5%
F ±1pF
J±5%
K ±10%
P ±100% ~ 0%
Z ± 80% ~ –

Fig &

Part No Description

Index
R101

Resistors

RD-4Z820J Carbon: 82J

R102 RD-4Z201J Carbon1/4W-200J

Allowance
F±1%
J±5%
K ± 10%
M ± 20%
G±2%

INFORMATION OF PART DESCRIPTION

Important Safety Notice

Components identified with the International Symbol have special characteristics important for safety.
When replacing any components, use only manufacturer’s specified parts.

Abbreviation of Description

LOC PART-CODE PART-NAME PART-DESC NOTE

00020 W3475N731- CORD POWER 3 H05VV-F 3X0.75 1.8 IV
00160

5M20000003 COIL TILT TC-17B-1 720D only
B002 5PB13857-- COIL BEAD BI3857(AXIAL)
B301 5PB13857-- COIL BEAD BI3857(AXIAL)
B502 5PB13857-- COIL BEAD BI3857(AXIAL)
B801 5PB13857-- COIL BEAD BI3857(AXIAL)
B802 5PB13857-- COIL BEAD BI3857(AXIAL)
B851 5PB13857-- COIL BEAD BI3857(AXIAL)
B852 5PB13857-- COIL BEAD BI3857(AXIAL)
B892 5PB13857-- COIL BEAD BI3857(AXIAL)
C001 CL1UC3224M C LINE ACROSS 0.22MF 1J(UCVSNDF/SV)+Q/O
C002 CH1FDF472M C CERA AC 2.5KV 4700PF M AC250V
C003 CEYP2G221Z C ELECTRO 400V SMH 220MF (25.4*40)
C005 CCXE3D103P C CERA HIKE 2KV 0.01MF P
C011 CCXF1H104Z C CERA 50V F 0.1MF Z
C012 CMXM2A473J C MYLAR 100V 0.047MF J (TP)
C021 CCXB3A471K C CERA 1KV B 470PF K (T)
C022 CCXB1H471K C CERA 50V B 470PF K (TAPPING)
C023 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11) TP
C024 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11) TP
C101 CEXF2E470V C ELECTRO 250V RSS 47MF (16X25) TP
C102 CEXF2E100V C ELECTRO 250V RSS 10MF (10X20) TP
C103 CEXF2A101V C ELECTRO 100V RSS 100MF (13X20) TP
C104 CEXF2A470V C ELECTRO 100V RSS 47MF (10X16) TP
C105 CEXF1E221V C ELECTRO 25V RSS 220MF (8X11.5) TP
C106 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11) TP
C107 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20) BK
C108 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20) BK
C109 CEXF1C101V C ELECTRO 16V RSS 100MF (6.3X11) TP
C110 CEXF1E102V C ELECTRO 25V RSS 1000MF (13X20) BK
C111 CEXF1E471V C ELECTRO 25V RSS 470MF (10X16) TP
C112 CEXF1C101V C ELECTRO 16V RSS 100MF (6.3X11) TP
C113 CMXL2E223J C MYLAR MEU 250V 0.022MF J(TP)
C115 CMXM2A473J C MYLAR 100V 0.047MF J (TP)
C117 CEXF1C101V C ELECTRO 16V RSS 100MF (6.3X11) TP
C118 CEXF1C102C C ELECTRO 16V RUS 1000MF (10X20) TP
C119 CCXB3A152K C CERA 1KV HIKB 1500PF K
C120 CCXB1H471K C CERA 50V B 470PF K (TAPPING)
C211 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C241 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11) TP
C301 CCXB1H221K C CERA 50V B 220PF K (TAPPING)
C303 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C304 CEXF1C471V C ELECTRO 16V RSS 470MF (10X12.5)BK
C305 CXCH1H150J C CERA 50V CH 15PF J (TAPPING)
C306 CXCH1H150J C CERA 50V CH 15PF J (TAPPING)
C307 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C309 CCXB1H102K C CERA 50V B 1000PF K (TAPPING)
C310 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP

45

!
!

ELECTRICAL PARTS LIST

The components identified by mark have special characteristics important for safety and x-ray radiation.
These should be replaced only with the types specified in the parts list.

46

LOC PART-CODE PART-NAME PART-DESC NOTE

C311 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C313 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP
C314 CCXB1H221K C CERA 50V B 220PF K (TAPPING)
C315 CCXB1H221K C CERA 50V B 220PF K (TAPPING)
C316 CCXF1H104Z C CERA 50V F 0.1MF Z
C317 CCXB1H221K C CERA 50V B 220PF K (TAPPING)
C320 CCXB1H221K C CERA 50V B 220PF K (TAPPING)
C323 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C361 CXCH1H221J C CERA 50V CH 220PF J (TAPPING)
C405 CEXF1C471V C ELECTRO 16V RSS 470MF (10X12.5)BK
C406 CMXL1J105J C MYLAR MEU 63V 1MF J
C408 CMXM2A562J C MYLAR 100V 5600PF J (TP)
C409 CMXM2A272J C MYLAR 100V 2700PF J (TP)
C411 CEXF1H221V C ELECTRO 50V RSS 220MF (10X16) TP
C412 CEXF1C471V C ELECTRO 16V RSS 470MF (10X12.5)BK
C415 CMXL1J105J C MYLAR MEU 63V 1MF J
C416 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C417 CMXL2A474J C MYLAR MEU 100V 0.47MF J
C501 CXCH1H101J C CERA 50V CH 100PF J (TAPPING)
C502 CMXL2A474J C MYLAR MEU 100V 0.47MF J
C503 CMXM2A222J C MYLAR 100V 2200PF J (TP)
C504 CEXF1C471V C ELECTRO 16V RSS 470MF (10X12.5)BK
C505 CCXB1H101K C CERA 50V B 100PF K (TAPPING)
C506 CCXB1H101K C CERA 50V B 100PF K (TAPPING)
C507 CMXM2A562J C MYLAR 100V 5600PF J (TP)
C508 CMXM2A103G C MYLAR 100V 0.01MF G (TP)
C509 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C510 CMXM2A822J C MYLAR 100V 8200PF J (TP)
C511 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C512 CMXM2A154J C MYLAR 100V 0.15MF J (TP)
C513 CMXL1J105J C MYLAR MEU 63V 1MF J
C515 CCXF1H104Z C CERA 50V F 0.1MF Z
C518 CMXM2A222J C MYLAR 100V 2200PF J (TP)
C522 CEXF1H470V C ELECTRO 50V RSS 47MF (6.3X11) TP
C526 CEXF2A100V C ELECTRO 100V RSS 10MF (6.3X11) TP
C532 CMXM2A103J C MYLAR 100V 0.01MF J (TP)
C533 CCXB1H101K C CERA 50V B 100PF K (TAPPING)
C534 CCXB2H102K C CERA 500V B 1000PF K (TAPPING)
C536 CCXB1H222K C CERA 50V B 2200PF K (TAPPING)
C537 CMXM2A562J C MYLAR 100V 5600PF J (TP)
C538 CXSL3D101K C CERA 2KV SL 100PF K(TP)
C539 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C540 CCXB2H471K C CERA 500V B 470PF K (TAPPING)
C541 CMXH3L222J C MYLAR BUP 3KV 2200PF J
C542 CMXH3L222J C MYLAR BUP 3KV 2200PF J
C543

CCXB3A102K C CERA 1KV B 1000PF K (TAPPING) 720D only
C543 CCXB3A152K C CERA 1KV HIKB 1500PF K 905D,905DF only
C543 CCXB3A222K C CERA HIKB 1KV 2200PF K 905DS only
C544 CXSL3D101K C CERA 2KV SL 100PF K(TP)
C545 CCXE3D103P C CERA HIKE 2KV 0.01MF P

!
!

47

LOC PART-CODE PART-NAME PART-DESC NOTE

C547 CEXF2E330V C ELECTRO 250V RSS 33MF (13X25) TP
C548 CMXL2E473J C MYLAR MEU 250V 0.047MF J(TP)
C549 CCXB3A102K C CERA 1KV B 1000PF K (TAPPING)
C551 CCXF1H104Z C CERA 50V F 0.1MF Z
C552 CMYF2D824J C MYLAR MPP 200V 0.82MF J
C553 CCXF1H104Z C CERA 50V F 0.1MF Z
C554 CMYF2D564J C MYLAR 200V MPP 0.56MF J
C555 CCXF1H104Z C CERA 50V F 0.1MF Z
C556 CMXF2D224J C MYLAR MPP 200V 0.22MF J
C559 CCXF1H104Z C CERA 50V F 0.1MF Z
C560 CMXF2D474J C MYLAR MPP 200V 0.47MF J
C562 CEXN2W479C C ELECTRO KMG 450V 4.7MF 10*20
C563 CCXE3D103P C CERA HIKE 2KV 0.01MF P
C565

CMXF2G104J C MYLAR MPP 400V 0.1MF J 905DS,905DF only
C565 CMXF2G124J C MYLAR MPP 400V 0.12MF J 720D,905D only
C566 CMXF2G124J C MYLAR MPP 400V 0.12MF J
C571 CCXF1H104Z C CERA 50V F 0.1MF Z
C577 CEXF2E100V C ELECTRO 250V RSS 10MF (10X20) TP
C578 CEXF2E100V C ELECTRO 250V RSS 10MF (10X20) TP
C580 CMXF2D124J C MYLAR MPP 200V 0.12MF J
C581 CEXD1C470F C ELECTRO 16V RND 47MF (8X11.5) TP
C585 CCXF1H104Z C CERA 50V F 0.1MF Z
C606 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C610 CMXF2D474J C MYLAR MPP 200V 0.47MF J
C612 CMXM2A104J C MYLAR 100V 0.1MF J (TP)
C801 CCXB1H472K C CERA 50V B 4700PF K (TAPPING)
C803 CEXF2E109V C ELECTRO 250V RSS 1MF (6.3X11)
C804 CEXD2A109F C ELECTRO 100V RND 1MF(5*11) TP
C805 CMXL2A104J C MYLAR MEU 100V 0.1MF J
C807 CCXF1H104Z C CERA 50V F 0.1MF Z
C811 CCXF1H223Z C CERA 50V F 0.022MF Z (TAPPING)
C814 CEXF1C470V C ELECTRO 16V RSS 47MF (5X11) TP
C817 CCXF1H104Z C CERA 50V F 0.1MF Z
C821 CCXF1H104Z C CERA 50V F 0.1MF Z
C822 CCXF1H104Z C CERA 50V F 0.1MF Z
C823 CEXF1C101V C ELECTRO 16V RSS 100MF (6.3X11) TP
C824 CCXF1H104Z C CERA 50V F 0.1MF Z
C825 CMXM2A103J C MYLAR 100V 0.01MF J (TP)
C826 CXSL3A470K C CERA 1KV SL 47PF K (TP)
C827 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C831 CCXB1H472K C CERA 50V B 4700PF K (TAPPING)
C832 CXCH1H330J C CERA 50V CH 33PF J (TAPPING)
C833 CEXF2E109V C ELECTRO 250V RSS 1MF (6.3X11)
C834 CEXD2A109F C ELECTRO 100V RND 1MF(5*11) TP
C835 CMXL2A104J C MYLAR MEU 100V 0.1MF J
C841 CXCH1H560J C CERA 50V CH 56PF J (TAPPING)
C842 CXCH1H560J C CERA 50V CH 56PF J (TAPPING)
C843 CCXF1H104Z C CERA 50V F 0.1MF Z
C844 CCXF1H104Z C CERA 50V F 0.1MF Z
C845 CCXF1H104Z C CERA 50V F 0.1MF Z

48

LOC PART-CODE PART-NAME PART-DESC NOTE

C846 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
C847 CCXF1H104Z C CERA 50V F 0.1MF Z
C848 CEXF2A220V C ELECTRO 100V RSS 22MF (8*11.5) TP
C849 CMXL2A104J C MYLAR MEU 100V 0.1MF J
C851 CEXF1C101V C ELECTRO 16V RSS 100MF (6.3X11) TP
C852 CCXF1H104Z C CERA 50V F 0.1MF Z
C854 CMXL2A104J C MYLAR MEU 100V 0.1MF J
C855 CEXF2A100V C ELECTRO 100V RSS 10MF (6.3X11) TP
C856 CEXF2A470V C ELECTRO 100V RSS 47MF (10X16) TP
C858 CMXL2E104J C MYLAR MEU 250V 0.1MF J
C859 CMXL2A104J C MYLAR MEU 100V 0.1MF J
C861 CCXB1H472K C CERA 50V B 4700PF K (TAPPING)
C863 CEXF2E109V C ELECTRO 250V RSS 1MF (6.3X11)
C864 CEXD2A109F C ELECTRO 100V RND 1MF(5*11) TP
C865 CMXL2A104J C MYLAR MEU 100V 0.1MF J
C867 CMXM2A102J C MYLAR 100V 1000PF J (TP)
C870 CCXF1H104Z C CERA 50V F 0.1MF Z
C871 CCXF1H104Z C CERA 50V F 0.1MF Z
C872 CCXB2H152K C CERA 500V B 1500PF K (TAPPING)
C873 CCXE3D103P C CERA HIKE 2KV 0.01MF P
C876 CEXF2A470V C ELECTRO 100V RSS 47MF (10X16) TP
CA301 9970770029 CONN AS SMH200-07+YBNH200-08=350
CA303 9970780033 CONN AS SMH200-08+YBNH200-09=500
CA701

9970740037 CONN AS YMH250-4+1007#24=250 905D,905DS,905DF only
CG01 9970710246 CRT GND AS 0.16*3*16+BL102NG=740 905D,905DF only
CS803 9979300007 SOCKET CRT ISDS08S
CT002

9970710246 CRT GND AS 0.16*3*16+BL102NG=740 905DS only
CT002 9970710251 CRT GND AS 0.16*3*16+BL102NG=730 720D only
CT802 9979617042 CDT M41KXU200XX061 (0.26) 720D only
CT802 9979619007 CDT M46QCE261X112(T4) 905D only
CT802 9979619008 CDT M46QCY261X112(SHORT) 905DS only
CT802 9979619011 CDT M46QCK761X123 (DF) 905DF only
CW001 485923242S CONN WAFER 5267-03A STICK TYPE 720D only
CW001 9979220075 CONN WAFER B3B-EH-A ST(TILT) 905D,905DS,905DF only
CW201 485923252S CONN WAFER 5267-04A STICK TYPE 905D,905DS,905DF only
CW203 9979220102 CONN WAFER SMW200-07 (ST)
CW801 9979220021 CONN WAFER SMAW250-06 (ANGLE)
CW802 9979220089 CONN WAFER SMAW200-08 (ANGLE)
CW803 9979220088 CONN WAFER SMAW200-07 (ANGLE)
D001 DD3SBA60-- DIODE D3SBA60
D002 DUF4007--- DIODE UF4007
D011 DZN4148--- DIODE 1N4148 AUTO 52MM
D021 D1N4937GP- DIODE 1N4937GP (TAPPING)
D022 DUF4007--- DIODE UF4007
D023 D1N4937GP- DIODE 1N4937GP (TAPPING)
D101 DUF4007--- DIODE UF4007
D102 DUF4007--- DIODE UF4007
D103 DUG2D----- DIODE UG2D 200V 2A
D104 DUG2D----- DIODE UG2D 200V 2A
D105 DUG2D----- DIODE UG2D 200V 2A

!
!

!
!

49

LOC PART-CODE PART-NAME PART-DESC NOTE

D106 D1N4937GP- DIODE 1N4937GP (TAPPING)
D107 DUG2D----- DIODE UG2D 200V 2A
D108 DZN4148--- DIODE 1N4148 AUTO 52MM
D109 D1N4937GP- DIODE 1N4937GP (TAPPING)
D111 D1N4937GP- DIODE 1N4937GP (TAPPING)
D203 DZN4148--- DIODE 1N4148 AUTO 52MM
D301 DZN4148--- DIODE 1N4148 AUTO 52MM
D302 DZN4148--- DIODE 1N4148 AUTO 52MM
D308 DZN4148--- DIODE 1N4148 AUTO 52MM
D311 DZN4148--- DIODE 1N4148 AUTO 52MM
D312 DZN4148--- DIODE 1N4148 AUTO 52MM
D313 DZN4148--- DIODE 1N4148 AUTO 52MM
D314 DZN4148--- DIODE 1N4148 AUTO 52MM
D315 DZN4148--- DIODE 1N4148 AUTO 52MM
D316 DZN4148--- DIODE 1N4148 AUTO 52MM
D317 DZN4148--- DIODE 1N4148 AUTO 52MM
D318 DZN4148--- DIODE 1N4148 AUTO 52MM
D319 DZN4148--- DIODE 1N4148 AUTO 52MM
D401 D1N4002A-- DIODE 1N4002
D501 DZN4148--- DIODE 1N4148 AUTO 52MM
D502 DZN4148--- DIODE 1N4148 AUTO 52MM
D532 DFMLG22S-- DIODE FML-G22S
D534 DDD54RC--- DIODE DAMPER DD54RC
D536 DUF4007--- DIODE UF4007
D537 DRP1H----- DIODE RP1H
D538 DS2L60---R DIODE S2L60
D581 DZN4148--- DIODE 1N4148 AUTO 52MM
D591 D1N4937GP- DIODE 1N4937GP (TAPPING)
D801 DZN4148--- DIODE 1N4148 AUTO 52MM
D802 DZN4148--- DIODE 1N4148 AUTO 52MM
D803 DBAV20---- DIODE BAV20
D804 DZN4148--- DIODE 1N4148 AUTO 52MM
D805 DZN4148--- DIODE 1N4148 AUTO 52MM
D822A DDZ5R1B--- DIODE ZENER DZ-5.1B
D823 DBAV20---- DIODE BAV20
D831 DZN4148--- DIODE 1N4148 AUTO 52MM
D832 DZN4148--- DIODE 1N4148 AUTO 52MM
D833 DBAV20---- DIODE BAV20
D834 DZN4148--- DIODE 1N4148 AUTO 52MM
D835 DZN4148--- DIODE 1N4148 AUTO 52MM
D861 DZN4148--- DIODE 1N4148 AUTO 52MM
D862 DZN4148--- DIODE 1N4148 AUTO 52MM
D863 DBAV20---- DIODE BAV20
D864 DZN4148--- DIODE 1N4148 AUTO 52MM
D865 DZN4148--- DIODE 1N4148 AUTO 52MM
D891 DBAV20---- DIODE BAV20
DG001

5MG0000069 COIL DEGAUSSING DG-905D 905D only
DG001 5MG0000069 COIL DEGAUSSING DG-905D 905DF only
DP001 5MG0000064 COIL DEGAUSSING DG-712D 720D only
DP001 5MG0000069 COIL DEGAUSSING DG-905D 905DS only

!
!
!

!

50

LOC PART-CODE PART-NAME PART-DESC NOTE

DZ011 DDZ4R7BM-- DIODE ZENER DZ-4.7BM
DZ101 DGDZJ18C-- DIODE ZENER GDZJ 18C
DZ201 DDZ5R1B--- DIODE ZENER DZ-5.1B
DZ202 DDZ5R1B--- DIODE ZENER DZ-5.1B
DZ203 DDZ5R1B--- DIODE ZENER DZ-5.1B
DZ204 DDZ5R1B--- DIODE ZENER DZ-5.1B
DZ316 DDZ5R1B--- DIODE ZENER DZ-5.1B
DZ501 DDZ4R7BM-- DIODE ZENER DZ-4.7BM
DZ531 DDZ15BM--- DIODE ZENER DZ15BM
F001 5F3CB3122L FUSE CERA SEMKO TL 3.15AH 250V MF51
I401A 1KA2142--- IC V-OUT KA2142
I802A 1LM2453T-- IC VIDEO OUTPUT LM2453T
I802C 9970710186 CONN AS 1015#18BK=120
IC001 1TEA1504-- IC POWER TEA1504
IC101 1K1A7812P1 IC REGULATOR KIA7812API
IC102 1K1A7805P1 IC REGULATOR KIA7805API
IC103 1KA431AZ-- IC REGULATOR KA431AZ
IC104 1KA78R05-- IC REGULATOR KA78R05
IC106 TBT169D--- SCR BT169D
IC203 124C08---- IC EEPROM 24C08
IC301 1MC908BD48 IC MICOM MC68HC908BD481B
IC302 1K1A7042P- IC SWITCH KIA7042P
IC303 1DBL358--- IC DBL358 DUAL OP-AMP
IC501 1TDA4856-- IC H.OSC TDA4856
IC601 1DBL358--- IC DBL358 DUAL OP-AMP
IC801 1LM1253N-- IC VIDEO PRE-AMP LM1253N
J292 RD-4Z100J- R CARBON FILM 1/4 10 OHM J
J322 RD-2Z399J- R CARBON FILM 1/2 3.9 OHM J
J330 RD-4Z479J- R CARBON FILM 1/4 4.7 OHM J
J389

RD-4Z479J- R CARBON FILM 1/4 4.7 OHM J 720D only
J389 RD-AZ479J- R CARBON FILM 1/6 4.7 OHM J 905D,905DS,905DF only
J556 RD-4Z100J- R CARBON FILM 1/4 10 OHM J
L101 5MC0000079 COIL CHOKE 101K
L102 5MC0000079 COIL CHOKE 101K
L103 5MC0000079 COIL CHOKE 101K
L104 5MC0000079 COIL CHOKE 101K
L105 5MC0000079 COIL CHOKE 101K
L801 5CPZ228K02 COIL PEAKING 0.22UH K(AXIAL 3.5MM)
L831 5CPZ228K02 COIL PEAKING 0.22UH K(AXIAL 3.5MM)
L861 5CPZ228K02 COIL PEAKING 0.22UH K(AXIAL 3.5MM)
L862 5CPZ128K02 COIL PEAKING 0.12UH K(AXIAL 3.5MM)
L863 5CPZ128K02 COIL PEAKING 0.12UH K(AXIAL 3.5MM)
LED1 DSD50GYW-- LED SD50GYW(GREEN/AMBER)
P001 9979500019 RECEPTACLE BNS-02AA4LR-2
PCB1

9979800497 PCB CONTROL T=1.6*215*36 905D,905DS only
PCB1 9979800534 PCB CONTROL T=1.6*215*36 905DF only
PCB1 9979800542 PCB MAIN T=1.6*330*246 (905D)
PCB1 9979800547 PCB VIDEO T=1.6*123*95 (905D)
PH001 1TLP721GR- IC PHOTO COUPLER TLP721D4GR
PR001 DECPAC140M POSISTOR ECPAC140M290

51

LOC PART-CODE PART-NAME PART-DESC NOTE

Q011A TSPP04N60S FET SPP04N60S5
Q100 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q104 TZTC3207-- TR KTC3207 (AUTO)
Q105 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q301 TZSR1006-- TR KSR1006 (AUTO)
Q303 TZSR1006-- TR KSR1006 (AUTO)
Q304 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q361 TZTC3202Y- TR KTC3202Y (AUTO)(1959Y)
Q362 TZTA1270Y- TR KTA1270Y(AUTO)(562Y)
Q501 TZSR1006-- TR KSR1006 (AUTO)
Q511 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q531 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q532 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y)
Q533 T1RF630A-- FET IRF630A
Q535 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q536 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y)
Q537 T2SJ449--- TR 2SJ449
Q539A T2SC5411-- TR 2SC5411
Q551 T1RF640--- FET IRF640
Q552 T1RF640--- FET IRF640
Q553 T1RF640--- FET IRF640
Q554 T1RF630A-- FET IRF630A
Q555 T1RF640--- FET IRF640
Q556 TZSR1006-- TR KSR1006 (AUTO)
Q557 TZSR1006-- TR KSR1006 (AUTO)
Q558 TZSR1006-- TR KSR1006 (AUTO)
Q559 TZSR1006-- TR KSR1006 (AUTO)
Q560 TZSR1006-- TR KSR1006 (AUTO)
Q561 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y)
Q562 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q563 TKSC5042F- TR KSC5042F
Q564 TKSC5042F- TR KSC5042F
Q581 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y)
Q582 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y)
Q583 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q591 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q592 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO)
Q593 TKSA910Y-- TR KSA910Y
Q601 TZTC3202Y- TR KTC3202Y (AUTO)(1959Y)
Q602 TZTA1270Y- TR KTA1270Y(AUTO)(562Y)
R002 RD-2Z334J- R CARBON FILM 1/2 330K OHM J
R003 RD-2Z334J- R CARBON FILM 1/2 330K OHM J
R004 RS02Z334J- R M-OXIDE FILM 2W 330K OHM J
R010 RD-2Z475J- R CARBON FILM 1/2 4.7M OHM J
R011 RD-2Z475J- R CARBON FILM 1/2 4.7M OHM J
R013 RD-AZ474J- R CARBON FILM 1/6 470K OHM J
R015 RD-AZ221J- R CARBON FILM 1/6 220 OHM J
R016 RD-AZ272J- R CARBON FILM 1/6 2.7K OHM J
R017 RD-AZ333J- R CARBON FILM 1/6 33K OHM J
R021 RD-AZ220J- R CARBON FILM 1/6 22 OHM J

!

52

LOC PART-CODE PART-NAME PART-DESC NOTE

R022 RD-AZ471J- R CARBON FILM 1/6 470 OHM J
R023 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R025 RW01Z128JN R WIRE WOUND 1W 0.12 OHM J NON-INDUCT
R026 RX05V122J- R CEMENT 5W 1.2K OHM J VERTICAL
R027 RD-AZ563J- R CARBON FILM 1/6 56K OHM J
R028 RD-AZ330J- R CARBON FILM 1/6 33 OHM J
R103 RD-AZ122J- R CARBON FILM 1/6 1.2K OHM J
R104 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R105 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R107 RD-4Z123J- R CARBON FILM 1/4 12K OHM J
R108 RN-AZ1803F R METAL FILM 1/6 180K OHM F
R110 RD-AZ153J- R CARBON FILM 1/6 15K OHM J
R111 RN-AZ6191F R METAL FILM 1/6 6.19K OHM F
R112 RS02Z249J- R M-OXIDE FILM 2W 2.4 OHM J (TAPPING)
R120 RD-4Z224J- R CARBON FILM 1/4 220K OHM J
R121 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R122 RD-AZ122J- R CARBON FILM 1/6 1.2K OHM J
R123 RD-AZ471J- R CARBON FILM 1/6 470 OHM J
R124 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R125 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R126 RS01Z689J- R M-OXIDE FILM 1W 6.8 OHM J (TP)
R127 RD-2Z123J- R CARBON FILM 1/2 12K OHM J
R133 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R211 RD-AZ622J- R CARBON FILM 1/6 6.2K OHM J
R212 RD-AZ822J- R CARBON FILM 1/6 8.2K OHM J
R272 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R301 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R303 RD-4Z221J- R CARBON FILM 1/4 220 OHM J
R304 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R305 RD-AZ106J- R CARBON FILM 1/6 10M OHM J
R306 RD-AZ333J- R CARBON FILM 1/6 33K OHM J
R307 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R310 RD-AZ393J- R CARBON FILM 1/6 39K OHM J
R316 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R317 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R318 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R319 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R320 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R321 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R322 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R323 RD-AZ222J- R CARBON FILM 1/6 2.2K OHM J
R324 RD-AZ222J- R CARBON FILM 1/6 2.2K OHM J
R325 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R327 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R328 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R334 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R351 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R352 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R353 RD-AZ242J- R CARBON FILM 1/6 2.4K OHM J
R354 RD-AZ242J- R CARBON FILM 1/6 2.4K OHM J

53

LOC PART-CODE PART-NAME PART-DESC NOTE

R355 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R361 RD-AZ393J- R CARBON FILM 1/6 39K OHM J
R362 RD-AZ473J- R CARBON FILM 1/6 47K OHM J
R363 RD-4Z822J- R CARBON FILM 1/4 8.2K OHM J
R364 RD-2Z470J- R CARBON FILM 1/2 47 OHM J
R365 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R366 RD-2Z100J- R CARBON FILM 1/2 10 OHM J
R367 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R368 RD-AZ122J- R CARBON FILM 1/6 1.2K OHM J
R369 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R370 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R372 RD-4Z101J- R CARBON FILM 1/4 100 OHM J
R403 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R404 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R405 RD-2Z129J- R CARBON FILM 1/2 1.2 OHM J
R408 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J
R409 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J
R411 RD-2Z129J- R CARBON FILM 1/2 1.2 OHM J
R412 RD-2Z109J- R CARBON FILM 1/2 1 OHM J
R413

RD-2Z209J- R CARBON FILM 1/2 2 OHM J 905DS only
R413 RD-2Z279J- R CARBON FILM 1/2 2.7 OHM J
R414

RD-2Z229J- R CARBON FILM 1/2 2.2 OHM J 905DS only
R414 RD-2Z249J- R CARBON FILM 1/2 2.4 OHM J 720D,905D only
R414 RD-2Z279J- R CARBON FILM 1/2 2.7 OHM J 905DF only
R416 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J
R417 RD-AZ562J- R CARBON FILM 1/6 5.6K OHM J
R418 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J
R420

RS02Z151J- R M-OXIDE FILM 2W 150 OHM J (TAPPING) 720D,905D,905DS only
R420 RS02Z181J- R M-OXIDE FILM 2W 180 OHM J (TAPPING) 905DF only
R423 RD-AZ822J- R CARBON FILM 1/6 8.2K OHM J
R501 RD-AZ561J- R CARBON FILM 1/6 560 OHM J
R502 RD-AZ244J- R CARBON FILM 1/6 240K OHM J
R503 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R504 RD-AZ753J- R CARBON FILM 1/6 75K OHM J
R505 RD-4Z479J- R CARBON FILM 1/4 4.7 OHM J
R507 RS02Z430J- R M-OXIDE FILM 2W 43 OHM J
R508 RS02Z430J- R M-OXIDE FILM 2W 43 OHM J
R511 RN-AZ2741F R METAL FILM 1/6 2.74K OHM F
R512 RD-AZ271J- R CARBON FILM 1/6 270 OHM J
R513 RD-AZ332J- R CARBON FILM 1/6 3.3K OHM J
R514 RD-AZ223J- R CARBON FILM 1/6 22K OHM J
R515 RD-AZ512J- R CARBON FILM 1/6 5.1K OHM J
R516 RD-AZ822J- R CARBON FILM 1/6 8.2K OHM J
R517 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R518 RD-AZ183J- R CARBON FILM 1/6 18K OHM J
R519 RD-AZ361J- R CARBON FILM 1/6 360 OHM J
R520 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R521 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R522 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R523 RD-AZ103J- R CARBON FILM 1/6 10K OHM J

54

LOC PART-CODE PART-NAME PART-DESC NOTE

R524 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R525 RS01Z129J- R M-OXIDE FILM 1W 1.2 OHM J (TAPPING)
R528

RD-AZ153J- R CARBON FILM 1/6 15K OHM J 905DF only
R528 RD-AZ393J- R CARBON FILM 1/6 39K OHM J 720D,905D,905DS only
R530 RD-AZ244J- R CARBON FILM 1/6 240K OHM J
R531 RS02Z201J- R M-OXIDE FILM 2W 200 OHM J
R531

RS02Z301J- R M-OXIDE FILM 2W 300 OHM J (TAPPING) 905DS only
R532 RS02Z331J- R M-OXIDE FILM 2W 330 OHM J TAPPING
R533 RS02Z201J- R M-OXIDE FILM 2W 200 OHM J
R533

RS02Z301J- R M-OXIDE FILM 2W 300 OHM J (TAPPING) 905DS only
R534 RD-AZ122J- R CARBON FILM 1/6 1.2K OHM J
R535 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R536 RS02Z222J- R M-OXIDE FILM 2W 2.2K OHM J (TAPPING)
R537 RD-4Z220J- R CARBON FILM 1/4 22 OHM J
R539

RS02Z159J- R M-OXIDE FILM 2W 1.5 OHM J 905DS only
R539 RS02Z209J- R M-OXIDE FILM 2W 2.0 OHM J 720D,905D,905DF only
R540 RS02Z159J- R M-OXIDE FILM 2W 1.5 OHM J 905DS only
R540 RS02Z209J- R M-OXIDE FILM 2W 2.0 OHM J 720D,905D,905DF only
R541 RD-AZ332J- R CARBON FILM 1/6 3.3K OHM J
R542 RD-AZ391J- R CARBON FILM 1/6 390 OHM J
R543 RD-4Z471J- R CARBON FILM 1/4 470 OHM J
R544 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R545 RS02Z200J- R M-OXIDE FILM 2W 20 OHM J (TAPPING)
R546 RS01Z221J- R M-OXIDE FILM 1W 220 OHM J (TAPPING)
R548 RD-AZ122J- R CARBON FILM 1/6 1.2K OHM J
R549 RD-4Z220J- R CARBON FILM 1/4 22 OHM J
R550 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R551 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R552 RD-AZ105J- R CARBON FILM 1/6 1M OHM J
R553 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R554 RD-AZ105J- R CARBON FILM 1/6 1M OHM J
R555 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R556 RD-AZ105J- R CARBON FILM 1/6 1M OHM J
R557 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R558 RD-AZ105J- R CARBON FILM 1/6 1M OHM J
R559 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R560 RD-AZ105J- R CARBON FILM 1/6 1M OHM J
R561 RD-AZ683J- R CARBON FILM 1/6 68K OHM J
R562 RX07V753J- R CEMENT 7W 75K OHM J VERTICAL
R563 RD-2Z754J- R CARBON FILM 1/2 750K OHM J
R564 RS02Z823J- R M-OXIDE FILM 2W 82K OHM J (TAPPING)
R565 RS02Z823J- R M-OXIDE FILM 2W 82K OHM J (TAPPING)
R566 RD-2Z203J- R CARBON FILM 1/2 20K OHM J
R567 RD-4Z101J- R CARBON FILM 1/4 100 OHM J
R568

RD-AZ271J- R CARBON FILM 1/6 270 OHM J 905DS only
R568 RD-AZ301J- R CARBON FILM 1/6 300 OHM J 905D,905DF only
R568 RD-AZ331J- R CARBON FILM 1/6 330 OHM J 720D only
R569 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R570 RD-AZ100J- R CARBON FILM 1/6 10 OHM J
R571 RD-AZ105J- R CARBON FILM 1/6 1M OHM J

55

LOC PART-CODE PART-NAME PART-DESC NOTE

R572 RD-AZ151J- R CARBON FILM 1/6 150 OHM J
R573 RD-AZ471J- R CARBON FILM 1/6 470 OHM J
R574 RD-AZ471J- R CARBON FILM 1/6 470 OHM J
R576 RD-4Z304J- R CARBON FILM 1/4 300K OHM J
R578 RS01Z129J- R M-OXIDE FILM 1W 1.2 OHM J (TAPPING)
R579 RD-4Z104J- R CARBON FILM 1/4 100K OHM J
R580 RD-AZ361J- R CARBON FILM 1/6 360 OHM J
R581 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R583 RD-AZ562J- R CARBON FILM 1/6 5.6K OHM J
R584 RD-AZ753J- R CARBON FILM 1/6 75K OHM J
R585 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R586 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R587 RD-2Z754J- R CARBON FILM 1/2 750K OHM J
R588 RS02Z364J- R M-OXIDE FILM 2W 360K OHM J (TP)
R590 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R591 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R592 RD-AZ333J- R CARBON FILM 1/6 33K OHM J
R593 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R594 RD-AZ123J- R CARBON FILM 1/6 12K OHM J
R595 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R596 RD-4Z513J- R CARBON FILM 1/4 51K OHM J
R597 RD-4Z274J- R CARBON FILM 1/4 270K OHM J
R601 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R602 RD-AZ513J- R CARBON FILM 1/6 51K OHM J
R606 RD-4Z822J- R CARBON FILM 1/4 8.2K OHM J
R607 RD-AZ393J- R CARBON FILM 1/6 39K OHM J
R608 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R614 RD-4Z100J- R CARBON FILM 1/4 10 OHM J
R702 RD-AZ302J- R CARBON FILM 1/6 3K OHM J
R703 RD-AZ273J- R CARBON FILM 1/6 27K OHM J
R704 RD-AZ153J- R CARBON FILM 1/6 15K OHM J
R705 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J
R706 RD-AZ623J- R CARBON FILM 1/6 62K OHM J
R801 RD-AZ750J- R CARBON FILM 1/6 75 OHM J
R802 RD-AZ330J- R CARBON FILM 1/6 33 OHM J
R804 RD-AZ820J- R CARBON FILM 1/6 82 OHM J
R805 RD-2Z330J- R CARBON FILM 1/2 33 OHM J
R807 RD-AZ105J- R CARBON FILM 1/6 1M OHM J
R811 RD-AZ121J- R CARBON FILM 1/6 120 OHM J
R812 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R813 RD-4Z104J- R CARBON FILM 1/4 100K OHM J
R820 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R821 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R822 RD-AZ432J- R CARBON FILM 1/6 4.3K OHM J
R823 RD-AZ331J- R CARBON FILM 1/6 330 OHM J
R824 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
R827 RD-AZ303J- R CARBON FILM 1/6 30K OHM J
R828 RD-AZ301J- R CARBON FILM 1/6 300 OHM J
R829 RD-AZ301J- R CARBON FILM 1/6 300 OHM J
R831 RD-AZ750J- R CARBON FILM 1/6 75 OHM J

56

LOC PART-CODE PART-NAME PART-DESC NOTE

R832 RD-AZ330J- R CARBON FILM 1/6 33 OHM J
R834 RD-AZ820J- R CARBON FILM 1/6 82 OHM J
R835 RD-2Z330J- R CARBON FILM 1/2 33 OHM J
R837 RD-AZ105J- R CARBON FILM 1/6 1M OHM J
R851 RD-AZ750J- R CARBON FILM 1/6 75 OHM J
R861 RD-AZ750J- R CARBON FILM 1/6 75 OHM J
R862 RD-AZ330J- R CARBON FILM 1/6 33 OHM J
R864 RD-AZ820J- R CARBON FILM 1/6 82 OHM J
R865 RD-2Z330J- R CARBON FILM 1/2 33 OHM J
R866 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
R867 RD-AZ105J- R CARBON FILM 1/6 1M OHM J
R890 RD-AZ753J- R CARBON FILM 1/6 75K OHM J
R891 RD-2Z101J- R CARBON FILM 1/2 100 OHM J
R892 RD-4Z564J- R CARBON FILM 1/4 560K OHM J
R893 RD-4Z106J- R CARBON FILM 1/4 10M OHM J
R898 RD-2Z181J- R CARBON FILM 1/2 180 OHM J
RL001 5SC0102116 SW RELAY ALA2PF12 1C-2P
SC01 9970800048 CABLE SIGNAL AS 15P+2C/DDC=1.5M(GY275A)
SG801 DWSP201M-- SURGE ABSORBER WSP-201M
SG831 DWSP201M-- SURGE ABSORBER WSP-201M
SG861 DWSP201M-- SURGE ABSORBER WSP-201M
SG890 DWSP301M-- SURGE ABSORBER WSP-301M
SW701

5S50101Z01 SW TACT KPT-1115VM 1C-1P 720Donly
SW701 5S50101Z10 SW TACT KPT-1115AM 905D,905DS,905DF only
SW702 5S50101Z01 SW TACT KPT-1115VM 1C-1P 720D only
SW702 5S50101Z10 SW TACT KPT-1115AM 905D,905DS,905DF only
SW703 5S50101Z01 SW TACT KPT-1115VM 1C-1P 720D only
SW703 5S50101Z10 SW TACT KPT-1115AM 905D,905DS,905DF only
SW704 5S50101Z01 SW TACT KPT-1115VM 1C-1P 720D only
SW704 5S50101Z10 SW TACT KPT-1115AM 905D,905DS,905DF only
SW705 5S50101Z01 SW TACT KPT-1115VM 1C-1P 720D only
SW705 5S50101Z10 SW TACT KPT-1115AM 905D,905DS,905DF only
SW706 5S50101Z01 SW TACT KPT-1115VM 1C-1P 720D only
SW706 5S50101Z10 SW TACT KPT-1115AM 905D,905DS,905DF only
T001 5RM0000104 TRANS SMPS DMT-905D
T201 5RH0000134 FBT HVGII-30
T501 5RD0000053 TRANS DRIVE DDT-905D
T502 5MH0000081 COIL H-LINEARITY TRL-905D
T503 5R50000038 TRANS BUCK DT-905D
T506 5RF0000008 COIL SIZE DCT-905D
TH001 DTP8D13--- THERMISTOR TP8D13
VR501 RV6421104P R SEMI FIXED CCT 065AT 100K OHM B TAP
VR581 RV6421102P R SEMI FIXED CCT 065AT 1K OHM B TAP
X301 5XE24R000E CRYSTAL QUARTZ HC-49/U 24.00000MHZ 30PPM

!

!

DAEWOO ELECTRONICS CO., LTD

686, AHYEON-DONG MAPO-GU
SEOUL, KOREA
C.P.O. BOX 8003 SEOUL, KOREA
TELEX : DWELEC K28177-8
CABLE : "DAEWOOELEC"
E-mail : [e-mail]
TEL : [phone]
FAX : [phone]