Daewoo 5520CRA, DSJ-4720CRA, DSJ-4710CRA, 5510CRA User Manual

REAR PROJECTION TV

INSTRUCTION MANUAL

REAR PROJECTION TV

DSJ-4710CRA / 5510CRA
DSJ-4720CRA / 5520CRA

PROJECTION TV

-1-

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

IMPORTANT SAFEGUARDS

-2-

1. Read, Retain and Follow All Instructions

Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions
for future reference. Follow all operating and use instructions.

2. Heed Warnings

Adhere to all warnings on the appliance and in the operating instructions.

3. Cleaning

Unplug the TV from the wall outlet before cleaning. Do not use liquid, abrasive, or aerosol cleaners. Cleaners
can permanently damage the cabinet and screen. Use a lightly dampened cloth for cleaning.

4. Attachments and Equipment

Never add any attachment and/or equipment without approval of the manufacturer as such additions may
result in the risk of fire, electric shock or other personal injury.

5. Water and Moisture

Do not use the TV where contact with or immersion in water is possible. Do not use near bath tubs, wash
bowls, kitchen sinks, laundry tubs, swimming pools, etc.

6. Accessories

Do not place the TV on an unstable cart, stand, tripod, or table. The TV may fall, causing
serious injury to a child or adult and serious damage to the TV. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold with the TV. Any mounting
of the TV should follow the manufacturer’s instructions, and should use mounting accessories
recommended by the manufacturer. An appliance and cart combination should be
moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance
and cart combination to overturn.

7. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and
to protect it from overheating. Do not block these openings or allow them to be obstructed by placing the TV
on a bed, sofa, rug, or other similar surface. Nor should it be placed over a radiator or heat register. If the TV
is to be placed in a rack or bookcase, ensure that there is adequate ventilation and that the manufacturer’s
instructions have been adhered to.

8. Power Source

This TV should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied to your home, consult your appliance dealer or local power company.

9. Grounding or Polarization

This TV is equipped with a polarized alternating current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug.

10. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the TV.

11. Lightning

For added protection for this TV during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent
damage to the TV due to lightning and power-line surges.

Please read the following safeguards for your TV and retain for future reference.
Always follow all warnings and instructions marked on the television.

12. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching such power lines or circuits as contact with
them might be fatal.

13. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

14. Object and Liquid Entry

Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or
short-out parts that could result in fire or electric shock. Never spill liquid of any kind on or into the TV.

15. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the TV, be
sure the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static charges.
Section 810 of the National Electric Code, ANSI /NFPA No. 70-1984,
provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.

16. Servicing

Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.

17. Damage Requiring Service

Unplug the TV from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
(a) When the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen into the TV.
(c) If the TV has been exposed to rain or water.
(d) If the TV does not operate normally by following the operating instructions. Adjust only those controllers

that are covered by the operating instructions as an improper adjustment of other controllers may result in
damage and will often require extensive work by a qualified technician to restore the TV to its normal

operation.
(e) If the TV has been dropped or the cabinet has been damaged.
(f) When the TV exhibits a distinct change in performance - this indicates a need for service.

18. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.

19. Safety Check

Upon completion of any service or repair to the TV, ask the service technician to perform safety checks to
determine that the TV is in safe operating condition.

20. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.

-3-

EXAMPLE OF ANTENNA GROUNDING

GROUND CLAMP

ELECTRIC
SERVICE
EQUIPMENT

NEC — NATIONAL ELECTRICAL CODE

ANTENNA
LEAD IN WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

GROUNDING
CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)

Warning

-4-

This section must be read carefully and followed by the
user prior to the operation of the product.

The manual states important instructions for the user's own safety, and the proper operation of the product.

In case of an accident, please unplug the unit from the outlet immediately.

Take the plug when unplugging the unit
from the outlet. The cord may cause fire or
electric shock if damaged.

Do not place the product in a lean or
unstable place since it may cause a serious
injury to a person, as well as damage to the
product if it falls.

To reduce the risk of electric shock, do not
remove cover or back. No user -serviceable
parts inside. Refer to qualified service personnel
for repair.

Do not put any object that contains water ­such as flowerpot - on the unit.
The water may penetrate into the unit, and be
a cause of fire or hazardous electric shock.

Do not put on or use the product near water and
moisture-such as in a bathroom, washbowl, etc.
It may be a cause of fire and electric shock
hazards.

To prevent fire and damages to the product,
unplug the unit from the outlet during lightning
storm, or when it is left unattended and unused
for a long period of time.

Do not let children hang on or climb on the
product since it may be a cause of serious
injury.

Slots and openings in the case are provided for
ventilation to ensure reliable operation of the
product. Never put in any item-such as a coin,
paper, match- through these openings since it
may touch dangerous voltage points that could
result in fire or shock hazard.

Caution

-5-

Please keep the user's manual in a safe place for future reference.

This section must be read carefully and followed by the user when installing and transporting the product.

Do not put volatile substance-such as
benzene, naphtha- near the product since it
may cause a change in the product's color.

Do not put magnetic related substance, or
telephone near the product since it may
cause distortion of the image

Do not expose the product in a dusty or
moisturized place since it may be a cause of
malfunctioning.

Place the television far away from the view
since it may cause damage in your eyesight.

Refer servicing to qualified service
personnel for cleaning at least once a year
since dust inside the TV set may be a result
or fire and malfunctioning of the product.

The product should be situated away from
any heat source-such as radiators, heat
registers, stoves, or other products that
produce heat.

Do not put on any heavy item on the power
cord since it may result in fire or hazardous
electric shock if the cord is damaged.

Do not cover the top of the television set.
Ventilation will be prevented, and it may be
a cause of fire if the product is internally
overheated.

Unplug the power from the outlet and all the related
connections from the unit to prevent electric shock. At least
two people must work together to move the TV set when
transporting to prevent the TV from falling, and
consequently, any serious injury or damage.

Do not touch the power cord with
moisturized or watery hands when plugging
to or unplugging from the outlet since it may
be a cause of electric shock.

Please be advised of electric wires and cables when installing
the antenna. It may be a cause of hazardous electric shock and
fire if the antenna touches or falls on the electric wire; thus, it
must be installed firmly, and far away from the cables.

Do not spill water or drop the remote
controller since it may be a cause of
malfunctioning.

This product has advantages as follows.

-6-

Make Sure of Auxiliary Parts.

MAIN POWER

STAND BYTIMERVOLCH MENU

TV/COMP.

TV/VIDEOPOWER

Large Screen

You can enjoy favorite broadcasting by using a
large screen with the size of 55”/47” bases on
projection technology.

Various Screen

You can watch various sizes of screen such as 16:9, 4:3, Panorama, Zoom.

4:3 Zoom1 Zoom2Panorama

OPTIONAL ADJUSTMENT OF SOUND

You can adjust sound per frequency like Audio since the equalizer is built-in.

CONNECTION OF VARIOUS DEVICES

You can watch many kinds of media in a large screen through connection of DVD or DTV, etc.

Adoption Dolby Virtual

You can enjoy vivid and stereo sound as in
a theater.

16:9

TV is easily falled by pulling or pushing it.
Specially when children hang on TV or climb on it,
there accident could occur.
Install prevention of conduction for safety.

1. Hold fixing hole and clamp by screw in
the back of TV

2. Bind it to steadily strong wall or prop by
hard strings It is safe that strings is
bound like right picture.

When you move the TV, you should attention
the strings. Use prop for TV that can
stand the weight of TV

Information of setting up TV

Table of Contents

-7-

Installation and Maintenance

Antenna Connection 8
Video Connection 11
Camcorder & Play station Connection 12
DVD Connection 13
Audio Connection 14
Digital Satellite Receiver Connection 15
Cable TV Broadcasting Connection 16
Name of Each Part 18

Basic Guide

To setup device change of remote control 22
Method To Use Basic Menu 23
To Watch TV 24
Automatic Channel Memory 26
Selection of Input Signal 32

Application Guide

Screen Adjustment 35
Selection of PIP 44
Sound Adjust 49
Adjustment of Color Match 56
Selection of Language 58
Troubleshooting 59
Standard of Product 60

Antenna Connection

-8-

1. Connect the feeder cable of the antenna to the combining adapter.

2. Connect the combining adapter to the antenna input at the back of the TV set.

WHEN THE IMAGE IS NOT CLEAR

Unclear screen image and bad
reception may be a cause of wrong
antenna connection. Be sure to check
its direction and place when installing.

WHEN USING THE COMBINING ADAPTER

You may obtain the combining adapter
at your closest Service Center.

Antenna Input

Indoor Antenna Connection

-9-

Such community TV Antenna installation may be found in most of co-op apartments.

When a coaxial cable is used

Plug the coaxial cable to the antenna socket, and fix it firmly by turning it to the right.

When a feeder cable is used

ANT/CABLE 1

ANT/CABLE 1

CTV Antenna Connection

-10-

Outdoor Antenna connection-such as VHF or/and UHF-may be necessary for installation at private
houses

Single Antenna Connection.

Separate Antenna Connection.

VHF Antenna

UHF Antenna

ANT/CABLE 1

ANT/CABLE 1

Outdoor Antenna Connection

The following connection allows you to record TV programs.

Connecting with an Antenna

Video Connection

-11-

You may connect S-Video input to enjoy a clearer and brighter picture images. You can choose and

make the connection with any one of Video 1,2, or 3 inputs.

ANT/CABLE 1

Connection is not necessary in Mono mode.
Connect either S-Video or Video input to the unit. When both are connected, the output display will be
in S-Video.

Note
The stated connection does not comply with recording TV programs. You must make
the connection to the Antenna input socket as shown below for recording.

Connection Guide

1. Connect the antenna to the antenna input of the video

2. Make a connection of Antenna Output on Video and Antenna Input on TV with the coaxial cable
provided.

Operating Instructions

1. Adjust the channel selection switch at the rear side of the Video to 3 or 4.

2. Turn on the TV set, and adjust the channel to 3 or 4, to the number adjusted for step1.

3. Turn on the Video, insert the videocassette, and press the Play button.

Connecting with an External Source

Camcorder & Play station Connection

-12-

-Use the input jack provided at the side panel of the TV set

-Use the same connection method for playstation

-Connect the camcorder and video as follows.

-Turn the camcorder's video output switch on, and play the recorded material.

-Press the "TV/VIDEO" button, and select Video 1.

-Select A/V INPUT for the Video Input, and start recording.

Playing a Recorded Material and Recording a Video simultaneously

Video game

Watching the Camcorder Recording on TV

DVD Connection

-13-

-480i input signal is possible for DVD input.

-DVD screen output is composed of three separate primary color jack(Y/Cb/Cr), resulting in a higher image quality.

-Y/Cb/Cr, may also be noted as Y/PB/PR or Y/Pb/Pr in different DVD players.

-The DVD player

s audio output must be connected to the DVD audio input socket at the back of the TV set.

-You must use a 480p input capable DTV jack if you want to get the progressive scan (480p) DVD screen display.

DVD

Audio Connection

-14-

-You may minimize the volume of the TV set, and listen to the sound.

-The default status of Dolby Virtual is in Line out: Internal .

Standard Audio Connection

Digital Satellite Receiver Connection

-15-

The signal input of 1080i, 720p, and 480p are available in this product.

You may use a general A/V jack for its connection.

Digital Satellite Receiver

Watching High Definition Digital Broadcasting

Cable TV Broadcasting Connection

-16-

Watching cable television is only possible after you have subscribed to the local broadcasting company and
installed a cable receiver. You may make the connection to any of the Video input 1, 2, & 3.

Antenna Input Connection

Watching cable television is only possible after you have subscribed to the local broadcasting company and
installed a cable receiver.

Cable TV

Broadcasting

Station

External Input Connection Source

-17-

You can alternatively use the antenna input 1 or the antenna input 2 if changing setup in the <Menu>, <Channel

Setup> or <Antenna>.

Connection to antennas for General
Broadcasting or Cable Broadcasting

Connection to antennas for General
Broadcasting or Cable Broadcasting

In simultaneous use of antennas for Cable Broadcasting

and General Broadcasting

Name of Each Part

-18-

Buttons on the TV set have the same function as those of the remote controller.

Front Panel Button

If you turn the TV set off by pressing the main power button at this panel, it is as unplugging
the power cord from the outlet since this will prevent all operation of both the TV set and the
remote controller. Unless you are not using the unit for a long period of time, have the main
power on this panel turned on at all times.

Remote controller signal receiver

the screen contains the remote controller signal receiving window; thus, point the remote
controller towards the screen when using it.

Power/ Timer Lamp

Power lamp is blue color if power turns on and red color if power turns off.
Timer lam turns on in Off/On reservation.

Front Panel

-19-

Side Panel

It is convenient to use the input jacks
provided at the side panel when connecting
to the camcorder or play station. It is also
convenient when connecting a personal
computer to the TV set, and when listening
to the sound through headphones.

Back Panel

Side and Rear Panel

-20-

This remote controller is universal; thus, it may be convertible for TV, Video, CTV, etc.

Power

TV/VCR/CATV

Channel number (0-9)

Use to select channel directly 0~9

Prev

It returns to previous channel.

TV/Component

TV

Component 1 Component 2

TV

CH

▲/▼

Mute

Sound Mode

This feature allows you to choose the mode ,
Each time the button is pressed, it rotates from
Normal

Music Movie News User.

Bilingual Broadcasting

This feature allows you to select the
language while broadcasting.

100

Use it when selecting a channel

number of over 100

MENU

Use it to make picture adjustment,

screen format, sound adjustment,

input selection, and utilities.

TV/VIDEO

Use this function to make

video input selection.

It changes in the following sequence

TV

VIDEO1 2 3 TV

VOLUME

◀/▶

Dolby Virtual

CHANNEL ADD/ERASE

This feature either memorizes the

current channel or erases a channel

that has previously memorized.

Sleep Timer

This feature is used to set up the time

of automatic turn off.

Parts of the remote controller

DISPLAY

-21-

When the TV screen image is unclear

Do not drop or spill liquid on it.
Do not expose on heat, dust, and humidity

BATTERY INSTALLATION

Push to open the cover of the remote controller
Set the batteries in the battery cell after checking the
electrode, and then shut the cover.

VCR Function

REW, PLAY, FF, STOP, REC, PAUSE

Caption

This feature allows you to choose the
caption.
Each time the button is pressed it rotates
from CC1

CC2 CC3 CC4 Off

ANT

PIP

STILL

SWAP

Screen Size

This feature converts the screen size by
changing its aspect ratio. Each time you

press the button, it will be changed from

16:9

4:3 Panorama ZOOM1

ZOOM2

Auto Picture

Standard Cinema Dynamic

User

PIP

Search

TV/Video

Position

To setup device change of remote control

-22-

- The remote control is setup to be used for operating the HDTV provided together.
You may also setup the remote control in order to operate cable TV receiver or video, etc with a remote control.

METHOD TO SETUP DEVICE CHANGE OF REMOTE CONTROL

• Ensure that power plugs of the outside device to be used are connected and that power turns off.

• Find the code number of the outside device to be used in the code list (See Setup Code of Remote Control).

• Continue to press the device change button related with the outside device to be used when the device
change lamp (video / cable) flashes.

• With the remote control oriented downward, enter the remote control setup code number made of three
numbers by using the number button of the remote control. If the code is correctly entered, power will turn on
in the designated device (if no power turns on, repeat this process by using another code).

• Continue to press the device change button until the device change lamp flashes three times.

Remote Control Setup Code

Cable TV receiver

Brand Code

Panasonic 046 049
Philips 009 015 016 023

064 078 083
Samsung 001 033 067
Toshiba 054

Video

Brand Code

Daewoo 001 007 009 012 060 061

086 088 090 094 095 096

JVC 013 030 032 040 044 046

051 056 103 119 121 128
166

Mitzubisi 014 020 041 042 045 047

055 057 120 145

LG 013 014 020 079 084 092

099 127

Panasonic 062 066 070 078 106 114

122 146 147 156 160 161

Philips 030 032 033 050 063 067

079

Samsung 031 038 080 082 083 085

087 090 091 093 097 098

101 153 163
Sharp 030 050 118 143 150 164
Sony 005 011 030 048 052 053

054 072 073 074 118 136

151

Method to setup device change of remote control

Notices:

Caution

• l All the preset codes are erased when replacing the battery.
l In this case, you must reset the remote control again.

Method To Use Basic Menu

-23-

- Basic menu appears on the screen if pressing the menu button of the remote control.

- There are 5 items of Picture, Sound, Function, Set up and Special in the basic menu.

- Each item has sub-items under it. If the desired item is selected, the relevant sub-items are displayed upward.

PICTURE

SOUND

FUNCTION

SETUP

SPECIAL

Adjusts Brightness, Contrast & Sharpness, Color, Tint and Picture NR.

Adjusts Mode, Balance and Equalizer.

Adjusts Timer, PIP, Caption, Language and Parental Lock

Adjusts Air/Cable, Auto Program, Ch Edit, Antenna

Adjusts Convergence, Dolby Virtual, Component

Press the “Menu” button.

• The main menu appears if
pressing the Menu button.

Press the “◀VOL▶” button.

• You may setup according to the
directions on the screen after
selecting the desired item and
pressing the “◀VOL▶” button.

• If the setup is completed, exit
from the menu by pressing the
“Menu” button.

Basic Menu

To Watch TV

-24-

- Buttons with same name in the main body performs same function.

When pressing the Channel button

•Select two digits if using the number button
for channel selection.
For example, to watch the No.9 channel,
Press the number button 0 and 9.
If pressing only number 9, it takes long time
for selecting channel.

Press the “Main Power” button of the
main body.

•The buttons of the remote control and the
main body operate only when pressing the
“Main Power” button of the main body.
The remote control and the main body do not
operate if turning the “Main Power” button of
the main body off.

To suddenly turn sound off

1. Press the ‘Mute’ button.

2. No sound is heard if ‘Mute’ is displayed on

the screen.

3. Sound is heard again if pressing the ‘Mute’

button once again.
For example, please use this button when
telephone rings or when guest comes while
watching TV.

Check of TV operation status

• If pressing the “Display” button, status of

channel or broadcasting being currently
watched or entry status of video component
is displayed on the screen.

To Watch TV

-25-

Press the “Main Power” button.

• Press the “Main Power” button of the
main body.

• The main power lamp turns on in red
color.

• Press the “Power” button of the main
body or the “Power” button of the
remote control.

• The main power lamp turns on in
“green” color and the TV turns on.

POWER

Press the “▼CH▲” button.

• Select the desired channel by
pressing the “▼CH▲” button or the
number button.

Ex) Channel 09

Adjust volume.

•Sound reduces if pressing the
◀VOL button.

• Sound increases if pressing the

VOL▶ button.

Vol 9

Press the “Power” button for turning the TV off.

• TV turns off and the power
lamp changes to red color.

POWER

Air 09

Automatic Channel Memory

-26-

Press the “Menu” button.

• The menu screen appears as
follows.

• Press the “◀VOL▶” button until the
“△” mark will come on the “Set up”.

• Press the “CH▲” button if the “△”
mark will come on the “Set up”.

Select the “Air/Cable” by pressing the “▼CH▲” button.

• Select the “Air/Cable” by pressing
the “▼CH▲” button.

• Select “Air” to watch the general
broadcasting, and select “Cable” to
watch the cable TV by using the
“◀VOL▶” button.

- This is function for the TV to automatically memorize only the broadcasted channel. If setup the Auto Channel,
you can simply find out channels with the channel “▼CH▲” button and so need not to select channels by
pressing each channel number.

- Always enter this function at the regular TV On-Air time with antenna connected. Air/Cable channel currently On­Air is memorized respectively if setup Auto channel for the General/Cable broadcasting. Always perform this
process again if moving to another place or moving the TV.

Automatic Channel Memory

-27-

Auto Program is completed.

• A screen appears as in the right
if the Auto Program is completed.

• A screen appears as in the
paragraph 1 if pressing the menu
button.

• Continue to press the menu
button until the menu screen
disappears.

Check by pressing the “▼CH▲” button.

• Searches only the memorized
channel.

Select the “Auto Program”.

• Select the “Auto Program” with
the “▼CH▲” button.

Press the “VOL▶” button.

• Pressing the “VOL▶” button
automatically searches On-Air
Channel as in the right.

• On Air TV, searches from 2
channels through 69 channels, and
on Cable TV, searches from 1
channels through 125 channels.

• In this case, if pressing the menu
button, the automatic Channel
search is stop. However, channels
searched by that time are saved.

-28-

- This is method for additionally memorize channels not memorized due to weak broadcasting signal.

- This function is available even in the <Menu> - <Set Up> - <Ch Edit> - <Add/Erase>.

Select the Channel to memorize.

• Select the Channel by pressing
the number button.
Ex) “13” channel

Press the “Add/Erase” button.

• Add – Erase character

alternatively appears whenever
pressing this button.

• Add appears in green color and

Erase appears in red color.

• Adjust to Add.

• Watch the memorized Channel

with the “▼CH▲” button.

Check the Channel by pressing the “▼CH▲” button.

• “13” is selected by pressing the
“▼CH▲” button.

Additional Channel Memory

ADD/

ERASE

-29-

Select the Channel to erase.

• The Channel to erase with the
“▼CH▲” button.

• You may select the Channel by
pressing the number button.

Ex) “13” channel

Press the “Add/Erase” button.

• If pressing the “Add/Erase”
button, the Channel number
changes from green color to red
color.

• Add – Erase character
alternatively appears whenever
pressing this button.

- This is function to erase unnecessary Channel memorized.

- This function is available even in the <Menu> - <Set Up> - <Ch Edit> - <Add/Erase>.

Erase of Memorized Channel

Notices:

Cautions in menu setup

• Menu disappears if not operating any button for 10 seconds from the menu.
Press the menu button to erase the menu.

• Only Channel signal with signal in setting up automatic Channel is memorized
and other channels becomes as erase status.

• The screen appears as “Cable” when watching “Air” cable TV during reception
of TV.
You may select Air – Cable by pressing the “◀VOL▶” button.

ADD/

ERASE

-30-

- This is function to clearly adjust the screen to the minute part when any Channel screen appears as a dotted line
or when no color appears or when a stripe figure appears or when the screen is unstable.

Select the Set up with the “Menu” button and the “◀VOL ▶” button.

• The “△” mark appears as in the
right if pressing the “◀VOL▶”
button until it will arrive at the
Set up.

Select “Air/Cable”.

• This screen is used for selecting
“Air TV” and “Cable TV”

• The screen is changed to “Air
TV” and “Cable TV” whenever
pressing the “◀VOL▶” button.

When color looks separated

• You must adjust “Color Match”
when color of the screen (red, blue,
yellow) looks separated or looks
spread due to unmatched (See 56
page).

Minute Adjustment of Channel

-31-

Select Ch Edit

• The screen appears as in the
right if pressing the “Ch Edit”.

Other items for Channel adjustment

• This item enables to erase,
memorize or minute adjust the
channel.

• Select the desired Channel
firstly.

• Performs Add or Erase.

• Minute adjust enables to adjust
minute and clear thing on the
screen.

Select Fine

• Select Minute Adjust by using the
“▼CH▲” button.

• Stop to press the “◀VOL▶”
button if the screen becomes
best conditions.

Selection of Input Signal

-32-

Press the “TV/VIDEO” button.

• Screen changes as follows whenever pressing the
“TV/Video Input” button.

- See 11p for connection method of TV and “Video”.

- You cannot designate channels when watching video.

When watching video, Camcorder, Cable TV

Notices:

Cautions in menu setup

• Menu disappears if not operating any button for 10 seconds from the menu.

• Don’t connect video signal and S-video signal to the video input terminal
(1,2,3) at the same time. If connecting both signals at the same time, the S­video operates.

• You can watch only when this input terminal must be connected to the
composite video (generally video) signal.

• If sound signal is of mono method, connect it to the L-terminal of the sound
input terminal.

-33-

- See 13p, 15p for connection method of DTV and DVD (component input).

- Input component video (called as color difference signal) as DVD signal.

Press the “TV/COMP.” button.

• The screen changes whenever
pressing the button once.

Component 2 Component 1

When watching DTV and DVD (component input)

-34-

Press the Menu button.

Select “Component 1” or “2” from the “Special”.

• Component Off is repeated whenever pressing the “VOL▶” button.

• Component 1 is repeated whenever pressing the “VOL▶” button.

• Component 2 is repeated whenever pressing the “VOL▶” button.

• Press the “◀VOL▶” button until the “△” mark will come
on the “Special”.

• Press the “CH▲” button in the “△” mark will come ont the
“Special”

Method to watch by using Menu button

Screen Adjustment

-35-

- The user may select various screens designed in good appearance in respect of a professional without adjusting
the screen individually.

Press the “Auto Picture” button.

• The screen adjustment status changes as following
screens are displayed sequentially whenever
pressing the button of the Screen mode.

• Screen automatically changes to the User Screen if
adjusting Brightness, Contrast, Sharpness, Color, Tint
from individual screen mode.

• The screen returns to the mode prior to turn power off
if turning power off and then turning power in each
screen status.

When setting up various screen mode

AUTO

PICTURE

-36-

Press the “Menu” button.

Press the “ VOL▶” button.

• If pressing the “Volume ◀▶”
button, On and Off of the
Picture NR function are
repeated.

• Select On to select the Picture
NR function.

• Press the “◀VOL▶” button until
the “△” mark will come on the
“Picture”.

• Press the “CH▲” button if the
“△” mark will come on the
“Picture”.

• Press the “▼CH▲” button and
select “Picture NR”.

- Screen noise refers to that screen looks bad as abnormal signal (noise) generates on the screen when
broadcasting signals are weak.

When removing screen noise

-37-

- You can enjoy various screens by adjusting Brightness, Contrast, Sharpness, Color, Tint,
etc to the user’s taste.

Press the “Menu” button and “Picture”.

• Press the “◀VOL▶” button

until the “△” mark will come on
the “Picture”.

• Press the “CH▲” button if the

“△” mark will come on the
“Picture”.

Select the item desired to adjust and press the “◀VOL▶” button.

• Whenever pressing the

“▼CH▲” button, you can
select in the order of
Brightness, Contrast,
Sharpness, Color, Tint,
Picture NR function.

• The screen appears as in the

right if pressing the “◀VOL▶”
button after selecting items
desired to adjust with the “▼
CH▲” button.

• You can adjust Brightness by

pressing the “◀VOL▶”
button.

Adjust Brightness, Contrast, Sharpness, Color, T int,
in the same manner.

When adjusting the screen to taste

Notice

Brightness : Adjusts the whole of screen brighter or darker.
Contrast : Adjusts difference between brightness and darkness

between objects and background on the screen.

Sharpness : Adjusts outline of the screen smoothly or sharply.
Color : Adjusts color thinly or thickly.
Tint : Adjusts so that color of personal face becomes most naturally.
Picture NR : Automatically removes screen noise.

-38-

- Randomly change the size of the screen. Pleasure for enjoying the TV increases further.

- This mode does not operation in the component 1 and 2 terminal. (However, the mode operates when 480i is
entered into the component 1 and 2 terminal.)

- The 16:9 screen operates when power is turned on firstly.

Press the “Screen Size” button.

• The screen changes as below
whenever pressing the “Screen Size”
button.

• 16:9 : The 16:9 screen to prove atmosphere of the movie hall.

• 4:3 : General TV screen currently broadcasted.

• Panorama : Screen that extends the 4:3 image to 16:9 and spreads the left or right part,

and whose center provides natural and energetic feeling.

• Zoom 1 : Screen that enlarges image upward or downward.

• Zoom 2 : Screen that enlarges image upward or downward and inserts title for video

viewers into image.

16 : 9

4 : 3

Zoom 2

Zoom 1

Panorama

Adjustment of Screen Size

SCREEN

SIZE

-39-

- You can watch in character (English) as well as hear sound in watching English caption program.

Press the “Caption” button.

• Setup performed once continues to keep
the status as it is.

CAPTION

Select “Caption” after selecting the “Menu” button
and “Function”.

• Off - CC1 - CC2 - CC3 - CC4 is repeated whenever
pressing the “Volume ◀▶” button.

Method to Setup the “Caption” with Menu button

Method to Setup the Caption Screen Mode

-40-

- This is function to protect children or juveniles from the harmful broadcasting or videotapes.

Press the “Menu” button.

• Main menu appears as in the
right drawing.

Select “Function”.

• Select “Function” with the “△”
mark by using the “◀VOL▶”
button.

• Sub-menu appears if pressing
the “CH▲” button.

Select “Parental Lock” by pressing the “▲CH▼” button.

• Press the “VOL▶” button.

Setup of Parental Lock

-41-

Press “Password”.

• Press Password by using
number 0~9.

Caution) If using your password,

remember it. It is
needed for continuous
use of this function
hereafter.

On – Off of the Parental Control
is repeated whenever pressing
the “◀VOL▶” button.

• A guideline of TV is setup in all
the TV programs including
sports, news.

• The “▼CH▲” button selects
items and the “◀VOL▶” button
sets up or cancels each item.

-42-

• Rating of movie is setup even
in movie, videotape and other
media objects including TV
program.

• The “▼CH▲” button selects
items and the “◀VOL▶” button
sets up or cancels each item.

• Interrupts program without rating.

• Interrupts program of the input
terminal for the outside video
(video 1, 2, 3).

• Interrupts program of the PIP.

• Sets up the Unblock or the Block
with the “◀VOL▶” button.

-43-

“Change Password”.

• In the initial purchase of TV set, password is set to blank.
In continuous use of Parental Control, you need to change your password.

• If pressing the “◀VOL▶” button after selecting password, the second screen of
below drawing appears. Here, newly enter your unique password by using number of
0 through 9. Enter your password in the same manner once again.

Exit from the “Parental Control” menu.

• The main menu appears if pressing the menu button once.

• The OSD of the menu disappears if pressing the menu button until it disappears.

Selection of PIP

-44-

Press the “Menu” button and select “Function”.

• Select “Function” with the “△”
mark by using the “◀VOL▶”
button.

• Sub-menu appears if pressing
the “CH▲” button.

Select “PIP” by pressing the “▼CH▲” button.

3. Press the “◀VOL▶” button from the “PIP”.

• The screen status may change to General
Screen → Main/Auxiliary Screen → Two
Screen → Search Screen

General Screen

Main/Auxiliary Screen Search Screen

When selecting various PIP

- You can enjoy various screens to your taste by selecting various functions of PIP.
However, you cannot watch same Channel as main screen in the auxiliary screen.

- You cannot also watch the input terminal screen of the component 1 and 2 with a PIP (auxiliary screen).

Two Screen

-45-

Press the “PIP” button and press the “▼CH▲”
button of the “PIP”.

• Select the Channel by pressing the “▼CH▲” button at the right of the “PIP”
button.

• The memorized Channel of the auxiliary screen can be selected.

Press the “PIP” button and press the
“Position” button.

Position of the auxiliary screen changes whenever pressing the position
button.

Selection of Auxiliary Screen Position

In case of
Main/Auxiliary screen

In case of both
screens

Selection of Auxiliary Screen Channel

PIP

PIP

-46-

Press the “PIP” button and then press the “SWAP”
button.

• The main screen changes to auxiliary screen
and auxiliary screen changes to main screen.

In case of
Main/Auxiliary
screen

In case of both
screens

SWAP

When converting both main screen to auxiliary screen

PIP

-47-

Press the “Search” button.

The “▶” mark sequentially moves on the search screen
whenever pressing the position button on the search screen.

If pressing the Main/Auxiliary Conversion button on the
search screen, the search screen with the “▶” mark and
the main screen converts each other .

4-screen Channel Search Function

- You can identify broadcasting contents while sequentially searching for only the memorized channel.

▶

▶▶

▶

▶

▶

Notice

Selection of input signal from the auxiliary

Press the “TV/VIDEO” button inside of the remote control on the PIP.

• You can watch video, cable broadcasting, etc on the auxiliary screen.

• This mode does not operation in the component 1 and 2 terminal.
Use the still function of external sets(DVD player.etc).

• The auxiliary screen changes in the order of TV → Video1 →
Video2 → Video3 → TV whenever pressing the button.

-48-

Still of Main Screen

• Press the “Still” button when
desiring to still the screen
currently watched.

• Pressing the button once again
returns to the screen being
watched as the still screen is
cancelled.

Still of Auxiliary Screen

• Press the “Still” button while pressing the “PIP” button.

• The auxiliary screen is temporarily stop if pressing the “Still” button in
the PIP.

• Pressing the button once again returns to the screen being watched
as the still screen is cancelled.

STILL

Still

- This is function to temporarily stop the main screen or the auxiliary screen currently watched.

- You can watch favorite scene, etc without missing important information since you can stop the screen.

PIP STILL

Sound Adjust

-49-

Press the “Sound Mode” button.

• Sound status changes while the
following screens displays in turn
whenever pressing the Sound
Mode button.

When selecting various sound modes

SOUND

MODE

-50-

Select “Sound” by pressing the “Menu” button.

• The menu screen
appears as follows:

Select items desired to adjust and press the “◀VOL ▶” button.

• You can select item in
the order of Mode →
Balance → Equalizer
whenever pressing the
button.

What’s equalizer?

• High quality sound range
adjustment method used
for audio products.

Sound Balance

• Function to adjust
balance of sound volume
of the left and right
speaker.

When adjusting sound to taste

- The user can enjoy various sounds by adjusting Sound Mode, Balance, Equalizer

-51-

In case of adjusting equalizer

• Select the Equalizer by pressing the “▼CH
▲” button.

• If pressing the “◀VOL▶” button, the
Equalizer Adjust mode appears.

0.1 kHz, 0.3 kHz Low Sound Range

1.0 kHz, 3.0 kHz Middle Sound Range

10.0 kHz, 0.3 kHz High Sound Range

Select and use the relevant frequency by pressing
the “◀VOL ▶” button.

• You can adjust degree of the
relevant frequency by using the
“▼CH▲” button.

Adjust sound balance in the same manner, either.

Dolby Virtual Sound

You can perspective, orientation and a cubic effect through the left/right speaker by developing the existing
surround system function.

Press the “Dolby Virtual” button.

• Dolby Virtual On → Dolby Virtual
Off is repeated whenever
pressing the Dolby Virtual button.

• You can also operate this function
with the menu button.

-52-

In Multi-sound and Stereo Broadcasting

Press the “MTS” button.

• The status changes while following screens sequentially
appears when pressing the button.

MTS

Multi-Sound and Stereo

- You can select to your taste since multi-sound broadcasting is broadcast in the order of Mono → Stereo → SAP.

- In stereo broadcasting, automatic conversion to the status selected in the multi-sound broadcasting is done.

- You may also select this function even in <Menu> → <Sound> → Mode by pressing the menu button.

-53-

Press the “Menu” button and select “Function”.

• Select “Function” by
pressing the “◀VOL▶”
button and then press the
“CH▲” button.

- You must previously adjust current time in order to reserve Automatic On/Off.

Press the “Timer” for selection.

• Select “Timer” by pressing
the “▼CH▲” button and
then press the “◀VOL▶”
button.

Setup the “Clock”.

• Hour is set up if pressing
the “◀VOL” button and
minute is set sup if
pressing the “VOL▶”
button.

• The menu disappears if
pressing the menu button
three times.

Press the “Menu” button if time setup is completed.

Adjustment of Current Time

Notice.

Current time is erased if setting up the Off status by pressing the
main power button.

• Leave the main power button in the On status in the case of not using
TV for a long time.

Function

Timer
PIP
Caption
Language
Parental Lock

Move Sel. Prev.

English

Off

-54-

The red lamp turns on even setting up either of Off-time/ On-time.
This function is very convenient since TV is automatically turned off at the fixed time if reserving the Off-time for
sleeping time or at desired time.
If adjusted once, this function operate everyday unless canceling the Off-time setup or pulling the plugs out.
You can reserve current time if setting it up previously.
On/Off time setup is erased if pressing and turning the main power off.

Select “Function” after pressing the “Menu” button.

• Select “Function” by
pressing the “◀VOL▶”
button and then press the
“CH▲” button.

Press “Timer” for selection.

• Select “Timer” by pressing
the “▼CH▲” button and
then press the “◀VOL▶”
button.

Select “Off Time” by pressing the “▼CH▲” button.

• Hour is set up if pressing
the “◀VOL” button and
minute is set sup if
pressing the “VOL▶”
button.

• Select “Off-time” by pressing
the “▼CH▲” button and
select ‘On” by pressing the
“◀VOL▶” button.

• Hour is set up if pressing the
“◀VOL” button and minute is
set sup if pressing the “VOL
▶” button.

Press the “Menu” button if time setup is completed.

Setup of Off-time

Notice.

Setup of On-Time

• Setup in the same manner as in setup of Off Time.

• Reservation function allowing TV to turn on to the desired time.

• If adjusted once, the On-time continues to operate everyday unless canceling setup
or taking out the TV plugs.

• It is convenient if setting up so that it turns on the rising time in the morning.

• You can reserve by previously adjusting current time.

Function

Timer
PIP
Caption
Language
Parental Lock

Move Sel. Prev.

English

Off

-55-

- This is function to reserve so that TV turns off after a fixed time (10 min. ~ 90 min.)
has passed from the current time.

- Adjust sleep time with sleep reservation button of a remote control.

Press the “SLEEP” button.

• Sleep Off → Sleep 10 → Sleep 20 → Sleep 30 →
Sleep 60 → Sleep 90 → Sleep Off is repeated
whenever pressing the “Sleep” button.

• Stop to pressing at the desired time.

• Sleep Off means status that “Sleep” is not setup.

SLEEP

Reservation of Sleep Time

Adjustment of Color Match

-56-

Press the “Menu” button.

• The Menu screen appears as in
the right.

Select “Special”.

• Select “Special” with the “◀
VOL▶” button.

• The extension appears if
pressing the “CH▲” button.

Adjustment of Color Match

- Perform this adjustment when color looks separated or when focus is not suitable or when the screen looks
spread, after movement to another place or watching projection TV for a long time.

(

-57-

Select “Convergence”.

Adjust the Convergence.

• The “▼CH▲” button selects items
and the “◀VOL▶” button changes
data of the selected item.

• The “◀VOL” button moves color to the
left (upper) and the “VOL▶” button
moves color to the right (lower).

• Adjust the screen so that color of the
middle cross becomes white.

• Adjust blue color in the same manner.

• Adjust the screen so that color of the
middle cross becomes white in the
length and the width.

Press the “Menu” button.

• Press the menu button until the menu screen disappears.

• Ensure that color is correct by turning the channel.

• Perform setup again if color is unmatched.

• Before thinking it as failure

Selection of Language

-58-

Press the menu button and select “Function”

Select language the “▼CH▲ button”

Press the “◀VOL▶ button from Language.

This function enables to select language of the OSD displayed on the TV screen.
Language of the OSD consists of English, French and Spanish.

Language of the OSD
changes in the order of
English → Français →
Español whenever pressing
the volume button.

Selection of Language

T roubleshooting

-59-

Symptoms and Solutions

Please check the following list prior to calling Daewoo Electronics Service Center for assistance

Is the TV power cord plugged
into the outlet correctly?
Please check the power cord
and connect it properly to the
outlet.
Press the main power button at
the front controller panel.

Has the "mute" button at the
remote controller been pressed
accidentally?
Have you checked its volume?
Press the "mute" button on the
remote controller once more.
Adjust the volume pressing the
"right" button

Have you checked the Color?
Isn't the program itself
broadcasting in black and white?
Have you checked the antenna
connection?
Adjust the color pressing the
“Vol

/ ”buttons as explained in
page 37
Check other broadcasting
programs
Check the antenna

Is the antenna towards the right
direction?
Hasn't the Channel Fine Tuning
been adjusted wrongfully?
Turn the antenna towards
where the broadcasting station
is
Press the Fine Tuning button
and adjust the screen image

Have you checked the antenna?
Have you checked whether it
has been interfered by vehicles
or neon signs?
Connect the antenna or change
the antenna cable.

Have you checked whether it
has been interfered by any
other receiving waves-such as
radio?
Avoid any subject that may
interfere its proper operation

This may happen when there is
a bad reception due to
interference or depending on
the location of the broadcasting
station.
Press the "map" button and
select "Forced Mono"

Hasn't the remote controller receiving
window be blocked or interfered by
any object?
Aren't the batteries on the remote
controller low?
Hasn't the remote controller mode set
up in cable mode?
Please clear away any object that may
block the TV from receiving the
remote controller signals.
Press the "TV/Input" or "TV/CATV"
button to change its current mode.

Standard of Product

-60-

Consult the service center after promptly cleaning this
product with clean water and drying it at a shade.
Never plug-in the power cords since electrical shock or
damage of part may occur.

DSJ-4710CRA/4720CRA Model DSJ-5510CRA/5520CRA

VHF 2~13, 14~69 Receipt Channel VHF 2~13, 14~69

CATV 1~125 CHANNEL CATV 1~125 CHANNEL

119cm Screen Size 139cm

NTSC Signal Method NTSC

15W / ch (Main L/R) Speaker Output 15W / ch (Main L/R)

AC 120V, 60Hz

Power

AC 120V, 60Hz

AC 220V, 50/60Hz(Chile, Peru) AC 220V, 50/60Hz(Chile, Peru)

230W Power Consumption 230W
1110 x 1210 x 533mm(4710) 1278 x 1352 x 586mm(5510)
1110 x 1210 x 530mm(4720)

Dimension (W/H/D)

1278 x 1352 x 591mm(5520)

62kg Weight 78kg

Appearance and standard of this product may change
without prior notice for improvement.