![](/html/53/53c7/53c7bbb1555932c14da51e8dddf8a91b0ff49d35a7e297d1ae1dfd12d6bda51b/bg1.png)
Document # PG01-010
RO230, ROV230
Revised 12/06/11 Page 1/2
Renaissance® 30” Wide,
Double Wall Oven
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
K
Utility
J
cutout
C
chassis
B
Top of
F
PLANNING
GUIDE
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
G
H
D
Control panel
front
Control panel
side view
(A) Overall
Width
29 7/8”
(75.9 cm)
(F) Utility
Cutout Width
6 1/4”
(15.9 cm)
A
E
(B) Chassis
Width
28 3/8”
(72.1 cm)
(G) Utility
Cutout Height
4 3/4”
(12.1 cm)
Top of
chassis
(C) Overall
Height
49 7/8”
(126.7 cm)
(H) Utility
Cutout Depth
7 3/4”
(19.7 cm)
60” (152 cm)
(D) Chassis
Height
49”
(124.5 cm)
(J) Control
Panel Depth
1 3/16”
(3.0 cm)
Conduit:
long
(E) Control
Panel
Overlay
7/8”
(2.2 cm)
(K) Chassis
(60.0 cm)
Depth
23 5/8”
21 1/8”
1 1/8”
(2.9 cm)
3 1/2”
(8.9 cm)
Epicure
HANDLE DIMENSIONS
ELECTRICAL SPECIFICATIONS
Dedicated Circuit
Requirements
240 Vac 60 Hz.,
4-wire,* 50 Amp.
* Two 120 Vac hot (L1 and L2), one neutral, one ground.
Fuse/circuit breaker on both L1 and L2.
3 3/16”
(8.1 cm)
(Order kit #AROVH30S)
1 1/8”
(2.9 cm)
Millennia
Total Connected Load
See product data label
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
![](/html/53/53c7/53c7bbb1555932c14da51e8dddf8a91b0ff49d35a7e297d1ae1dfd12d6bda51b/bg2.png)
Document # PG01-010
RO230, ROV230
Revised 12/06/11 Page 2/2
Renaissance 30” Wide,
Double Wall Oven
Cabinet tolerances: +1/16” (+1.6 mm) -0, unless otherwise stated
1” (2.5 cm) min.
to bottom of
cabinet door
PLANNING
GUIDE
N
Recommended
electrical
location
R
3/4” (1.9 cm)
support platform
DOUBLE WALL OVEN - CUTOUT DIMENSIONS
(N) Minimum
Cabinet
Width
P
4” typical toe kick
(P) Minimum
Cut Out Width
1” (2.5 cm) min.
to top of
drawer face
9 5/8” (24.4 cm)
recommended
(R) Minimum
Cutout Height
30”
(76.2 cm)
Minimum interior cabinet depth: 24” (61.0 cm)
All specications subject to change without notice.
28 1/2”
(72.4 cm)
49 1/8”
(124.8 cm)
Phone: (800) 793-0093www.dacor.com