Document # PG01-009
RNWO130, RNWOV130
Revised 12/1/17 Page 1/2
Renaissance® 30” Wide,
Single Wall Oven
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
K
B
Utility
J
C
A
cutout
Top of
chassis
F
PLANNING
GUIDE
WARNING
• Observe all governing codes and ordinances during
planning and installation. Contact your local building
department for further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
G
H
D
Control panel
front
Control panel
side view
(A) Overall
Width
29 7/8”
(75.9 cm)
(F) Utility
Cutout Width
6 1/4”
(15.9 cm)
3 1/2”
(8.9 cm)
(B) Chassis
Width
28 3/8”
(72.1 cm)
(G) Utility
Cutout Height
4 3/4”
(12.1 cm)
1 1/8”
(2.9 cm)
E
(C) Overall
Height
27 5/8”
(70.2 cm)
(H) Utility
Cutout Depth
7 3/4”
(19.7 cm)
3 3/16”
(8.1 cm)
Top of
chassis
1 1/8”
(2.9 cm)
Conduit:
60” (152 cm)
(D) Chassis
Height
26 5/8”
(67.6 cm)
(J) Control
Panel Depth
1 3/16”
(3.0 cm)
1 1/8”
(2.9 cm)
long
(E) Control
Panel
Overlay
1”
(2.5 cm)
(K) Chassis
Depth
23 5/8”
(60.0 cm)
21 7/8”
(55.6) cm
ELECTRICAL SPECIFICATIONS
Dedicated Circuit
Requirements
240 Vac 60 Hz., 4-wire,*
30 Amp.
* Two 120 Vac hot (L1 and L2), one neutral, one ground.
Fuse/circuit breaker on both L1 and L2.
Total Connected Load
See product data label
Epicure Flush
All specications subject to change without notice.
Millennia
(Order kit #AROVH30S)
HANDLE
DIMENSIONS
Phone: (800) 793-0093www.dacor.com
RNWO130, RNWOV130
Document # PG01-009
Renaissance 30” Wide,
Cabinet tolerances: +1/16” (+1.6 mm) -0, unless otherwise stated
N
Recommended
electrical
location
1” (2.5 cm) min.
to bottom of
cabinet door
Single Wall Oven
1 1/2”
(3.8 cm)
typical counter
36” typ.
(91.4 cm)
3/4” (1.9 cm)
support platform
SINGLE WALL OVEN - INStALLED UNDER COUNtER
Revised 12/1/17 Page 2/2
PLANNING
GUIDE
1“ (2.5 cm) min. to combustibles
R
P
1“ (2.5 cm) min.
to combustible floor
Recommended
4” typical toe kick
electrical
location
R
P
1” (2.5 cm) min.
to top of
cabinet door
4” typical toe kick
SINGLE WALL OVEN - CUtOUt DIMENSIONS
Alternate
electrical
support platform
location
3/4” (1.9 cm)
31 1/4” (79.4 cm)
recommended
(N) Minimum
Cabinet
Width
30”
(76.2 cm)
Minimum interior cabinet depth: 24” (61.0 cm)
(P) Minimum
Cut Out Width
28 1/2”
(72.4 cm)
(R) Minimum
Cutout Height
26 7/8”
(68.3 cm)
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
Loading...