Renaissance
Models: RNRP36GS, RNRP48GS
®
Gas Range
Installation Instructions
THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST
EDITIONS OF ANSI Z21.1, UL858 AND UL60730-1, STANDARDS FOR HOUSEHOLD
APPLIANCES.
Part No. 108531 Rev. B
Table of Contents
Important Safety Instructions .....................................................1
Planning the Installation .............................................................. 3
Electrical Requirements .............................................................. 3
Gas Supply Requirements
Product Dimensions .................................................................... 4
Cabinet Layout ............................................................................ 5
Installation Instructions
Preparing for Installation ............................................................. 6
IMPORTANT:
• Installer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully before you
begin the installation process. Leave these installation instructions with the customer.
• Customer: Keep these installation instructions for future reference and the local building inspector’s use.
.......................................................... 3
............................................................... 6
Gas Connection
Final Installation ........................................................................ 10
Installing the Burner Knobs ...................................................... 11
Cooktop Assembly
Verifying Proper Operation .......................................................13
Removing the Range for Service..............................................13
Reinstalling the Range After Service
Installation Checklist ................................................................. 13
.......................................................................... 9
.................................................................... 12
........................................ 13
Customer Service Information
If you have questions or problems with installation, contact your
Dacor dealer or the Dacor Customer Service Team. For repairs
to Dacor appliances under warranty call the Dacor Distinctive
Service line. Whenever you call, have the model and serial
number of the appliance ready. The model and serial number
label is located inside the grate, inside the door.
Dacor Customer Service Team
Phone: (800) 793-0093 ex. 2813 (U.S.A. and Canada)
Monday — Friday 6:00
Web site: www.dacor.com
Dacor Distinctive Service (for repairs under warranty only)
Phone: (800) 793-0093 ex. 2822 (U.S.A. and Canada)
Monday — Friday 6:00
Model and serial
number label located
inside grill
a.m. to 5:00 p.m. Pacific Time
a.m. to 5:00 p.m. Pacific Time
Model Identification
RNRP36GS/NG/H
SIZE (width in inches)
COLOR
C = Custom color
S = Stainless steel
GAS TYPE
NG = Natural Gas
LP = Liquid Petroleum (Propane)
ALTITUDE
H = Equipped for high altitude operation,
4000 ft. (1219 m) and up
No Character = Equipped for low altitude operation
Model and Serial Number Location
All specifications subject to change without notice.
No liability is assumed by Dacor
®
for changes to specifications.
© 2014 Dacor, all rights reserved.
Important Safety Instructions
Important Information About Safety
Instructions
The Important Safety Instructions and warnings in this manual
are not meant to cover all possible problems and conditions
that can occur. Use common sense and caution when installing,
maintaining or operating this or any other appliance.
Always contact the Dacor Customer Service Team about problems
and conditions that you do not understand.
Safety Symbols and Labels
DANGER
Immediate hazards that WILL result in severe personal injury or
death.
WARNING
Hazards or unsafe practices that COULD result in severe
personal injury or death.
CAUTION
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
WARNING
If the information in this manual is not
followed exactly, a fire or explosion may
result causing property damage, personal
injury or death.
- Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
WARNING
WARNING – NEVER use this appliance as a space heater
to heat or warm the room. Doing so may result in carbon
monoxide poisoning and overheating of the appliance.
WARNING
NEVER cover any slots, holes or passages on the inside or
outside of the range or cover an entire rack with materials such
as aluminum foil. Doing so blocks air flow through the oven and
may cause carbon monoxide poisoning. Aluminum foil linings
may also trap heat, causing a fire hazard.
WARNING
Tip-over hazard:
• A child or adult can tip the range and be killed.
• Attach the anti-tip bracket to the floor as directed in these
installation instructions.
• Engage the anti-tip bracket by sliding the anti-tip foot on
the range into it according to these installation instructions.
Using a flashlight, be sure that the anti-tip bracket engages
the range’s anti-tip foot as shown below.
• After moving the range, be sure to re-engage the anti-tip
foot into the anti-tip bracket as shown below.
• See the anti-tip bracket installation instructions in this guide
for further details.
• Failure to follow these instructions can result in death or
serious burns to children or adults.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not use any phone in your building.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
- Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.
READ AND SAVE THESE INSTRUCTIONS
Anti-tip
bracket
Anti-tip foot
CALIFORNIA PROPOSITION 65 WARNING
The burning of gas cooking fuel generates some by-products
that are on the list of substances which are known by the State
of California to cause cancer or reproductive harm. California
law requires businesses to warn customers of potential
exposure to such substances. To minimize exposure to these
substances, always operate this unit according to the use
and care manual, ensuring you provide good ventilation when
cooking with gas.
1
Important Safety Instructions
WARNING
• Read the accompanying use and care manual before
operating this appliance.
• Keep packaging materials away from children. Plastic
sheets and bags can cause suffocation.
• If you receive a damaged product, immediately contact
your dealer or builder. Do not install or use a damaged
appliance.
• This range must be properly installed and grounded by a
qualified installer according to these installation instructions
prior to use. The installer should show the customer the
location of the gas shut off valve and the electrical outlet
so that they know where and how to turn off the gas supply
and power to the range.
• This appliance should not be installed with a ventilation
system that blows air downward toward the range.
This type of ventilation system may cause ignition and
combustion problems with the gas cooking appliance,
resulting in personal injury or unintended operation.
• Do not use this appliance in combination with a surface
(countertop) ventilation system.
• This appliance is not designed for installation in a mobile
home or recreational vehicle.
• Do not install, repair or replace any part of the range unless
specifically recommended in the literature accompanying
it. A qualified service technician should perform all other
service.
• Do not connect this range to the gas supply without the
supplied gas pressure regulator installed.
• Before performing any type of service or installation, make
sure the gas supply and power to the range are turned off.
• NEVER block or cover any slots, holes or passages
anywhere inside the oven or on the outside of the range or
cover an oven rack with materials such as aluminum foil.
Doing so blocks airflow through the oven and cooktop and
may cause carbon monoxide poisoning or fire. See the
Getting to Know Your Range section of the use and care
manual for the location of the various air holes (slots).
• Only use the range for cooking tasks expected of a home
appliance as outlined in the literature accompanying it. This
range is not intended for commercial use.
• DO NOT TOUCH THE SURFACES OF THE OVEN[S] OR
COOKTOP DURING OR IMMEDIATELY AFTER USE.
• To avoid the possibility of fire, never leave this appliance
unattended when the cooktop is in use.
• Do not climb on any part of the appliance.
• Do not leave children or pets alone or unattended in the
area around the range. Do not allow children to play with
the controls, pull on the handle(s), or touch other parts of
the range.
• Do not store items of interest to children on top of or
above the range. Children could be burned or injured while
climbing on the appliance.
• Do not attempt to use this appliance in the event of a power
failure.
WARNING
• Clean the cooktop thoroughly before operating it for the first
time.
• Keep flammable items, such as paper, cardboard, plastic
and cloth away from the burners and other hot surfaces.
Do not place such items in the oven(s). Do not allow pot
holders to touch hot surfaces or gas burners.
• Do not wear loose or hanging apparel while using the
range. Do not allow clothing to come into contact with the
interior of the oven(s) or the cooktop and surrounding areas
during and immediately after use.
• To avoid a fire hazard, do not hang flammable or heat
sensitive objects over the range. If the range is near a
window, do not use long curtains as window treatment.
The curtains could blow over the cooktop and create a fire
hazard.
• Do not use the oven(s) for storage.
• Do not touch the outside surfaces of the range during the
self-clean cycle. They will be hot. Venting from the oven
may cause the cooktop and backguard to become hot.
• Make sure that all the cooktop parts are dry before lighting
a burner.
• Turn the knobs to the “OFF” position prior to removing them
from the valve stems.
• The cooktop should never be operated without the knobs
and trim rings in place.
• For your safety, do not use the oven to cook without the
convection filter(s) installed. When the filter is not installed,
the spinning fan blades at the back of the oven are
exposed.
• Do not line the oven(s) with aluminum foil or other
materials. These items can melt or burn up during selfcleaning and cause permanent damage to the appliance.
• Non-stick coatings, when heated, can be harmful to birds.
Remove birds to a separate, well-ventilated room during
cooking.
• IMPORTANT - This appliance is equipped with a threeprong grounding plug for your protection against possible
electric shock hazards. Plug it only into a dedicated,
grounded three-prong electrical outlet. It is the responsibility
of the customer to make sure the proper type of outlet is
installed. Do not under any circumstances:
◊ Cut or remove the third (ground) prong from the power
cord.
◊ Use an adapter plug.
◊ Use an extension
cord.
◊ Use a power cord that
is frayed or damaged.
◊ Connect to an
electrical outlet with a
ground fault interrupter
(GFI).
2
Planning the Installation
B
A
WARNING
• IMPORTANT: Observe all governing codes and ordinances
during planning and installation. Contact your local building
department for further information.
• To prevent an electric shock hazard, the power supply
must meet the specifications stated below. It is the owner’s
responsibility to make sure that the electrical service meets
electrical requirements and that the electrical outlet has
been properly installed by a licensed electrician.
The appliance installation must be electrically grounded in
accordance with local codes or, in the absence of local codes,
with the National Electrical Code, ANSI/ NFPA 70:
Electrical Requirements
• The range is supplied with a factory installed, 6 foot long,
power cord with a three-prong grounding plug. It is connected
to the chassis at the rear of the range. It must be connected
to a dedicated, grounded three-prong electrical outlet.
• The correct voltage, frequency and amperage must be
supplied to the appliance from a separate, grounded, circuit
that is protected by a properly sized circuit breaker or time
delay fuse.
Total
Model Circuit Required
RNRP36G
RNRP48G
*These specifications for reference only. Refer to the rating label
for exact specifications (see below for location).
120 Vac, 60 Hz, 15 Amp.
120 Vac, 60 Hz, 15 Amp.
Connected
Load*
120 Vac 60 Hz,
5.0 Amp.
120 Vac 60 Hz,
8.0 Amp.
Gas Supply Requirements
• The installation of this appliance must conform with local
codes or, in the absence of local codes, with the National
Fuel Gas Code, ANSI Z223.1/NFPA 54.
• Be certain that the appliance being installed is correct for
the gas service provided (natural gas or LP gas). Also, if
operating the range at an altitude above 4000 ft. (1219 m)
make sure it is equipped for high altitude operation. Refer
to the range rating label and the table on the inside cover to
determine the correct model.
• See the table below for gas supply pressure requirements.
• The range comes from the factory with the regulator
installed. Use only the installed regulator. The regulator inlet
accommodates a 3/4” gas line. The range ships with a 1/2” to
3/4” adapter connected to the regulator.
GAS SUPPLY PRESSURE REQUIREMENTS*
Gas Type
Natural Gas 5” Water Column 6” Water Column
Liquid Propane (LP) 10” Water Column 11” Water Column
* The gas supply pressure for testing the regulator setting shall
be at least 1 inch water column (249 Pa) above the specified
manifold pressure.
** Maximum gas supply pressure for all models: 1/2 psi.
The ratings above are for reference only. Refer to the rating label
for exact specifications (see below left for location).
Minimum
Manifold Pressure
Minimum Gas
Supply Pressure**
View rating label through slot on
top of kick panel through opening
between door and range
Specifications Label Location
Gas
Inlet
GAS - ELECTRICAL ACCESS DIMENSIONS
Model A B
RNRP36G
RNRP48G
13 1/16” to 14 3/8”
(33.2 to 36.5 cm)
13 1/16” to 14 3/8”
(33.2 to 36.5 cm)
7 5/16”
(18.6 cm)
4 1/4”
(10.8 cm)
Power
cord
3
Planning the Installation
48” (121.9 cm)
Front of open door
Front of handle
Front edge of bull nose
Front panel
Rear of front panel/oven door
28 1/2” (72.4 cm)
(91.9 cm)
36 3/16”
(95.3 cm)
37 1/2”
26 7/8” (68.3 cm)
26” (66.0 cm)
24” (61.0 cm)
1 1/4”
(3.2 cm)
to
1 1/16” (2.7 cm) to cooking
surface (top of grates) from
top of trim
Finished side
panel
X
24” (61.0 cm)
Cabinet face
lines up with
back of control
panel
Product Dimensions
Product tolerances: ±1/16” (±1.6 mm)
*
* The backguard is
available in two heights;
3 inches (standard) and 9
inches (optional).
Width: RNRP36G - 35 7/8” (91.1 cm)
RNRP48G - 47 7/8” (121.6 cm)
4
View of Range Installed
(Side View)
Planning the Installation
Cabinet Layout
• All maximum and minimum dimensions and clearances
shown in the diagrams below must be maintained for safe
operation.
• Check the location where the range is to be installed. It
should be placed away from drafts that may be caused by
doors, windows and heating and air conditioning outlets.
• To reduce the risk of fire or personal injury from reaching over
a hot appliance, avoid cabinet installations directly above the
range. If cabinet storage is to be provided, the risk can be
reduced by installing a range hood that projects horizontally a
minimum of 5 inches beyond the bottom of the cabinets.
• The range may be installed flush to the rear wall. Dacor
strongly recommends installing a non-combustible material
on the rear wall above the range and up to the vent hood or
installation of a backguard. It is not necessary to install noncombustible materials behind the range below the countertop
height. Any openings in the wall behind the appliance or in
the floor underneath it must be sealed.
CUTOUT DIMENSIONS
Range Model F G H
RNRP36G
RNRP48G
42” (106.7 cm)*
36” (91.4 cm)**
54” (137.2 cm)*
48” (121.9 cm)**
* Recommended ** Minimum
36”
(91.4 cm)**
48”
(121.9 cm)**
33 1/2”
(84.8 cm)
43 1/2”
(110.2 cm)
Gas and Electrical Service
• The shaded area shown below denotes the location of the
gas inlet and the electrical outlet. This is the recommended
location. For replacement purposes, the location of the
existing utilities may be utilized provided they do not interfere
with the sides or rear of the range. Check local building codes
for permissible gas valve locations.
• An external manual shut-off valve must be installed between
the gas inlet and the range for the purpose of turning on or
shutting off gas to the appliance.
The installation must allow for the following:
• Access to the gas shut-off valve when the unit is installed.
• Access to the electrical outlet, when the range is in place.
• The gas supply piping and shut-off valve, and the electrical
outlet must be located so they do not interfere with the range
when it is installed.
• The electrical outlet and gas shut off valve must be located
so that the range can be pulled out for service while the
appliance remains connected.
Minimum Clearances
13” (33.0 cm)
5
max.
30” (76.2 cm)
15” (38.1 cm)
4, 5
min.
Note 2
37 1/2”
(95.3 cm)
max.
F
Non-combustible
surface along back wall
recommended
1
min.
Grate
level
Cutout tolerances: +1/16” (+1.6 mm), -0
unless otherwise stated
G
Suggested
location of
3
utilities
1
Vertical from range grate level to combustible overhead
surface; if installing an overhead vent hood, also check
hood specifications for minimum required clearances.
2
Cabinet/countertop depth is at discretion of customer but
cabinet face MUST NOT protrude further than rear of front
panel, see product dimensions.
3
Consult local code for exact location requirements.
4
Vertical from grate level to combustible surface.
5
This specification does not apply for cabinets more
than a horizontal distance of 10” (25.4 cm) from the
edge of the range.
10” (25.4 cm) min.
to combustible side
walls above the range
(both sides)
5
Installation Instructions
Preparing for Installation
WARNING
• If the gas or electric service provided does not meet the
product specifications, do not proceed with the installation.
Call the dealer, the gas supplier or a licensed electrician.
• Before installing the range, you must locate and secure the
anti-tip bracket to the floor.
IMPORTANT: Within the Commonwealth of Massachusetts, this
appliance must be installed by a licensed plumber or gas fitter.
Unpacking the Range
Unpack the parts box and verify that all required components
have been provided. If any item is missing or damaged, please
contact your dealer immediately. Do not install a damaged or
incomplete appliance.
Parts List
- 3 Grates
- 8 Standard burner caps
(4 brass, 4 porcelain)*
- 4 Standard burner rings
- 4 SimmerSear burner caps
(2 brass, 2 porcelain)*
- 2 SimmerSear burner rings
- 2 SimmerSear burner heads
- 2 GlideRack™ oven racks
- 1 Standard rack
- 2 GlideRack™ 18” wide oven
racks (RNRP48G only)
- 1 18” wide standard oven rack
(RNRP48G only)
*The range is supplied with two different types of burner caps
(brass and porcelain) to suit the customer’s preference. Please
note that the brass burner caps change color over time as the
result of heat.
- Knobs (4 Standard cooktop,
2 cooktop MAX GRIDDLE,
1 oven for RNRP36G,
2 oven for RNRP48G)
- Anti-tip bracket with screws
and anchors
- Griddle
- Wok ring
- Stainless steel cleaner
- Literature kit
- Broiler pan/grill
Install the Anti-Tip Bracket and Foot
Locate the anti-tip bracket included in the parts box.
There are two ways to mount the anti-tip bracket:
• Floor mounting (preferred method)
• Wall mounting (alternate method). Use this method if floor
mounting is not suitable. If the front panel of range (excluding
bull nose) is further than 27” (68.6 cm) from the back wall or if
the flooring is too thick (see Installing the Anti-Tip Bracket
on the Wall), the wall mounting method may not be used and
the floor mounting method must be suitable.
Installing the Anti-Tip Bracket on the Floor
WARNING
To perform its intended function, the anti-tip bracket must be
attached as instructed to the concrete slab or wood sub-floor
below any floor coverings (including cement board) on top. Do
not attach the anti-tip bracket directly to floor coverings such as
ceramic/asphalt tile or linoleum.
Anti-tip
bracket
Floor
covering
Screws attached to
Sub-floor
sub-floor below floor
covering
Concrete anchors shown, do
not use for wood sub-floor
Installing a 9 Inch Backguard (Optional)
Install the optional 9 inch backguard before making the range
gas and electrical connections. Install it according the installation
instructions included with the backguard kit.
Approved backguard kits:
Model Description
APB36D9 9 inch high backguard for range model RNRP36G
APB48D9 9 inch high backguard for range model RNRP48G
6
Four (4) plastic anchors are provided along with three sizes (4
each) of #8 or #12 Phillips head screws for attaching the antitip bracket to the floor. Use both the anchors and four (4) of the
screws when attaching the bracket to a concrete sub-floor. Do not
use the provided anchors when attaching to a wood sub-floor.
Installation Instructions
Installing the Anti-Tip Bracket on the Floor
(cont.)
1. Determine the location of the range center line and front
panel for the range’s final position based on the Product
Dimensions on page 5 and the actual cabinet/cutout
dimensions used for the installation.
2. Determine the required position of the anti-tip bracket, based
on the diagram below. Mark the four (4) mounting hole
locations on the floor with a pencil.
3. Determine the screw size required. The minimum full thread
depth (portion of screw threaded into wood/slab) for wood is
3/8” (1 cm) and 5/8” (1.6 cm) for concrete. See SCREW SIZE
TABLE to select the correct screw size.
Attaching the bracket to a concrete floor:
• Drill four (4) 3/8” diameter countersink holes through any
existing floor covering down to the concrete slab below.
• Drill the 4 holes for the anchors 1 1/4” (3.2 cm) deep into the
concrete slab using a 3/16” masonry bit. This hole length is
longer than the anchor, but is required for proper installation.
Clear the holes of dust and any other material. Tap each
anchor into the hole until the anchor top is flush with the top
of the concrete slab. Position the anti-tip bracket holes over
the anchor holes. Insert the screws through the 4 holes in
the base of the bracket and thread them into the anchors. Be
sure the screw threads fully engage the anchor body. Tighten
the screws into place.
Attaching the bracket to a wood floor:
• If there is ceramic, asphalt or other hard floor covering over
the wood below, drill (4) countersink holes to allow access to
the wood below for drilling pilot holes.
• Drill four (4) pilot holes into the wood floor using a drill bit
(1/16” dia. for #8 screws, 1/8” dia. for #12 screws). Position
the anti-tip bracket holes over the holes in the floor. Insert the
screws into the wood and tighten into place.
#8 x 1”
#8 x 1 1/4” or
#12 x 1 3/4
screw,
4 places
(see text)
Anchor, 4 places:
use for concrete
floor only
TOP VIEW
Range
center line
Range front
panel*
C
L
A
ANTI-TIP BRACKET PLACEMENT
Dimension RNRP36G RNRP48G
A 10 7/8” (27.6 cm) 1 1/2” (3.8 cm)
B 22 1/2” (57.2 cm) 22 1/2” (57.2 cm)
* Excludes bull nose (see page 4)
B
SCREW SIZE TABLE
Sub-Floor Type/Floor
Covering Thickness
Concrete or wood sub-
floor, no floor covering over
top
Concrete or wood sub-
floor, floor covering up to
1/4” thick
Concrete or wood subfloor, floor covering over
1/4” and up to 1/2” thick
Wood sub-floor, floor
covering over 1/2” and up
to 1 3/16” thick
Concrete under floor
covering over 1/2” thick
Wood sub-floor, floor
covering over 1 3/16” thick
* Included with range
** Determine required depth based on information in step 3 and
purchase from local hardware store.
Must be purchased separately **
Must be purchased separately **
Screw Size
#8 x 1 *
#8 x 1 *
#8 x 1 1/4 *
#12 x 1 3/4 *
7
Installation Instructions
Installing the Anti-Tip Bracket on the Wall
1. Determine the suitability of wall mounting the anti-tip bracket.
To use the wall mount option, the range front panel (excluding
the bull nose) must not be more than 27” (68.6 cm) from the
wall and the bracket screws must be able to thread into the
base plate inside the wall behind. The notches on the sides
of the bracket indicated the minimum required height of the
base plate inside the wall and that any floor covering is not
too thick for proper screw thread engagement.
Drywall
Anti-tip
bracket
Notch
Wall
Base
plate
2. To install the bracket, place it against the wall in the mounting
location. Using a drill with a 1/8” diameter drill bit, drill four
(4) 1 5/8” deep pilot holes perpendicular to the screw seating
surfaces shown below. Attach the bracket to the wall as
shown with the four (4) included #12 x 1 3/4 screws.
This hole lines up with
#12 x 1 3/4”
screw, 4 places
Back wall
Range
center line
bracket center line
To determine if the base plate is high enough:
◊ Determine the location of the range center line and front
panel when the range is in its final position based on the
product dimensions on page 5 and the actual cabinet/
cutout dimensions used for the installation.
◊ Determine and mark the required position of the anti-tip
bracket, based on the diagram above. Push the bracket
up against the wall in the mounting location.
◊ Using a pencil, make a dot next to the notches on both
sides of the bracket. Determine if the base plate is as
high at the notches by drilling test holes into the wall at
both dots with a 1/16” drill bit. Drill just deep enough to
see if the bit contacts the base plate. If the bit contacts
the base plate the location will support wall installation of
the anti-tip bracket. If you do not contact the base plate,
the wall mounting method may not be used and the floor
mounting method must be suitable, or the wall must be
modified so that the base plate is above the notches.
Bracket
center line
C
L
C
L
C
Range front
panel*
Top View - Location of Wall Mounted Anti-Tip
Bracket
ANTI-TIP BRACKET PLACEMENT
Dimension RNRP36G RNRP48G
C 11 7/8” (30.2 cm) 2 1/2” (6.4 cm)
* Excludes bull nose (see page 4)
8
Installation Instructions
Removing the Oven Door
WARNING
• Do not attempt to disengage the hinge catches with the
door(s) removed from the range. The hinge springs could
release causing personal injury.
• Do not lift or carry the oven door(s) by the handle.
NOTE: When installing a backguard, always install it before sliding
the range into place. See page 6.
To make the range easier to move, remove the door(s) to reduce
weight.
1. Open the door to its fully opened position.
2. Use a pair of needle nose pliers and a flat blade screwdriver
to rotate the catch over the retaining arm on each hinge.
Catch
Retaining arm
3. Lift the oven door to about a 15° angle from the vertical
position.
4. Hold the door with both hands just below the handle and pull
it away from the oven while continuing to lift.
Gas Connection
WARNING
• Make sure the gas supply valve is off and that the power
cord to the range is disconnected prior to connecting the
gas line.
• Do not apply excessive pressure when tightening gas
connections and fittings.
• Do not use Teflon tape or plumber’s putty on gas flex line
connections.
• For LP installations, the LP gas tank must have its own
high pressure regulator. This is in addition to the pressure
regulator provided with the range.
• The maximum gas supply pressure to the regulator must
never exceed 1/2 pound per square inch (psi) or 3.5 kPa.
• The range and shut-off valve must be disconnected from the
gas supply piping during any pressure testing exceeding 1/2
psi (3.5 kPa).
• The range must be isolated from the gas supply piping by
closing the shut-off valve during any pressure testing at or
below 1/2 psi (3.5 kPa).
• Check all gas lines for leaks as instructed to avoid a fire or
explosion hazard. Do not use a flame to check for leaks.
NOTE: The gas pressure regulator is pre-set at the factory for the
type of gas intended for use with the appliance. To verify that the
appliance is compatible with the type of gas available, check the
range rating label (see inside cover for location). Ranges intended
for use with LP gas will have “LP” as a part of the model number.
Consult your dealer if the range is not compatible with the type of
gas supplied.
Before sliding the range into the cabinet:
1. Make sure the gas supply valve is in the off position and that
power to the range is off.
2. Connect a flexible gas supply line to the gas shut-off valve
previously installed on the stub out. The gas line needs to be
long enough to allow the range to be pulled out for service.
3. Slide the gas line up through the access holes in the chassis
and up to the regulator. Move the wires around inside the
access holes to prevent them from catching on the gas line
as you push it up.
4. Connect the gas line to the regulator.
5. Turn all cooktop control valves to the “OFF” position. Turn on
the gas supply.
6. Check all lines and
connections for
leaks using a soap
and water solution.
7. After verifying that
there are no gas
leaks, turn off the
gas supply valve
connected to the
range to the off
position.
Regulator
connection
Door Gripping Points
9
Installation Instructions
Final Installation
1. Peel the protective plastic coating off of the range, including
the door.
2. Measure from the floor to the countertop. Adjust the leveling
legs as required to position the trim around the cooktop even
with or above the countertop.
3. Locate the anti-tip foot on the back of the range and lower
(turn) it until it is 1/16” (2 mm) off the floor.
Rear leg
Back of range
1 1/4” *
up
* Distance to floor:
4 1/16” to 5 5/16”
4. Carefully slide the range into position into the cutout. The
anti-tip foot should engage the anti-tip bracket. Using a
flashlight look underneath the range and verify that the
bracket covers the anti-tip foot.
down
Anti-Tip Foot
(location varies)
Re-installing the Oven Door(s)
WARNING
To avoid personal injury or damage to the door from it falling off
its hinges:
• Make sure that the notch on the bottom of each hinge rests
on top of the lower lip of each hinge receptacle before
attempting to open the oven door.
• Rotate the hinge locks toward the front of the range
immediately after installation of the door.
1. Grasp the oven door on opposite sides and hold it at a 15°
angle from the front of the oven. Slide the hinges into the
hinge openings, resting the bottom of the hinge arms on the
hinge receptacles. Continue to hold the door at a 15° angle
with one hand while pushing in on each of the bottom corners
of the door. Push until the notch on the bottom of each hinge
slips over the lower lip of each hinge receptacle.
2. Lower the door to the fully opened position.
3. Rotate both hinge locks toward the oven.
4. Slowly and carefully open and close the door completely to
ensure that it is properly installed.
5. Remove any packaging from inside the oven(s).
Anti-tip foot
5. Use a level to make sure that the range does not tilt front to
back or side to side. Re-adjust the legs to level and change
the height if necessary.
10
Anti-tip
bracket
Notch on bottom
of hinge
Lower lip of
hinge receptacle
Door Installation
BROIL500 °400 °300 °200 °WARM CLEAN
Installation Instructions
Installing the Burner Knobs
WARNING
Installing the range knobs in the wrong position may result
in damage to the griddle included with the range. The knobs
for the center burners are marked with the maximum griddle
settings.
NOTE: When installing the knobs, align the “D” shaped opening
on the back of the knob with the end of the valve shaft. Carefully
push the knob on until it stops.
There are three (3) different types of knobs supplied with the
range. The oven knob(s), has/have the word BROIL on them. The
knobs for the middle burners have the words “MAX GRIDDLE” on
them.
1. Put the oven knob(s) A on the oven valve shaft(s) as shown.
Oven Knobs A
C
C
B
A
B
C
C
2. Put the knobs with the words “MAX GRIDDLE” on them B
onto the center burner valve shafts as shown.
Icons on Center Burner Knobs B
3. Put the remaining knobs C on the outer valve shafts as
shown.
Icons on Outer Burner Knobs C
C
C
B
RNRP36G Knob Placement
A
A
B
C
C
RNRP48G Knob Placement
11
Installation Instructions
Cooktop Assembly
WARNING
Never attempt to operate the range’s cooktop with any of the
burner rings, burner caps or grates removed.
• Remove the burner rings, burner caps and grates from their
shipping packages.
• Install the burners as shown. Either type (color) of the
supplied burner caps may be used. When installing the
burner components, twist each piece back and forth slightly
until it drops completely into place. The burners will not
operate properly unless all of the burner pieces are properly
seated.
• Gently set the grates on top of the spill tray. Put the legs of
each grate inside the corresponding dimples.
Ridge on
bottom of
burner cap
SimmerSear
burner
Spill tray
Standard
burner
STEP 3: Install burner
cap. Ridge on cap must
surround top of ring.
STEP 2: Install
burner ring. Line up
ring tabs with head
slots.
STEP 1: Install
burner head. Put
locating tab in
keyed hole.
Burner ring
Burner head
STEP 3: Install burner
caps. Ridge on cap must
surround top of ring.
STEP 2: Turn ring until it
drops into place.
STEP 1: Put burner
ring on top of head.
Ridge on
bottom of
burner cap
Burner
ring
Keyed
hole
SimmerSear Burner Installation
12
Burner base
Burner
head
Standard Burner Installation
Installation Instructions
Verifying Proper Operation
Before operating the range, read the accompanying use and
care manual completely. It contains Important safety, service and
warranty information.
1. Before beginning the test procedure, ensure that all cooktop
control valves are in the OFF position, and all burner rings,
burner caps, and grates are properly positioned on the
cooktop frame.
2. Turn on the gas supply at the shut-off valve.
3. Connect the power cord to the electrical outlet. When the
range is first connected, the oven indicator light flashes on
and off for about 10 seconds while the range’s circuitry starts
up. Wait for the light to stop flashing before going to step 4.
4. Test one of the burners by pushing the knob in and turning
it counterclockwise to the HIGH position. It may take up to
four seconds for ignition to occur, at which time the ignitor will
stop sparking. If ignition does not occur within four seconds,
turn off the knob, wait for at least five minutes to allow any
gas to dissipate, then repeat the ignition test. After ignition,
rotate the control knob counterclockwise from HIGH to LOW
to adjust the flame height progressively. When the range is
installed properly, the flame will
be steady and quiet. It will also
have a sharp, blue inner cone that
will vary in length proportional to
the burner size. Dacor’s Smart
Flame™ feature reduces the flame
under the grate fingers to increase
grate life. If the range is equipped
for use with LP gas, the ends of
the flame may be yellow at the
tips, which is normal.
5. Turn the control knob to the OFF position.
6. Repeat the ignition test for all remaining burners.
After testing all the cooktop burners, turn them off.
7. Open the oven door(s). Test the oven light(s) by
turning on the light switch(s) on the control panel.
8. Turn on the convection fan switch(s). You should hear the
convection fan, located behind the screen at the back of the
oven, come on.
9. With the oven door open, turn the oven control knob to the
400 degree position. Both the knob itself and the oven ON
indicator light next to the knob should illuminate. Within 60
seconds you should hear the bake burner ignite below the
oven floor. It should begin to give off heat.
10. Turn the oven control knob to the BROIL position. The bake
burner should turn off. Both the oven control knob and the
oven ON indicator light should be illuminated.
11. Within 60 seconds the IR burner on the ceiling of the oven
should ignite and begin to give off heat.
12. Turn the oven knob to the “OFF” position. On model
RNRP48G, test both ovens.
If the range does not operate properly, follow these
troubleshooting steps:
1. Verify that power and gas are supplied to the range.
2. Check the electrical connections and gas supply to ensure
that the installation has been completed correctly.
Normal Flame
OFF Icon
3. Repeat the burner ignition test and/or oven test.
4. If the appliance still does not work, contact Dacor Distinctive
Service at (800) 793-0093 ex. 2822. Do not attempt to repair
the appliance yourself. Have the model and serial numbers
available when you call. See inside cover for location.
Dacor is not responsible for the cost of correcting problems
caused by a faulty installation.
Removing the Range for Service
1. Turn the gas supply valve to the off position.
2. Disconnect the power cord from the electrical outlet.
3. Pull the range out from the wall
Reinstalling the Range After
Service
1. Push the range into operating position, making sure the antitip bracket is engaged (see page 10).
2. Connect the power cord to the electrical outlet.
3. Turn the gas supply valve to the on position.
Installation Checklist
WARNING
• To ensure a safe and proper installation, the following
checklist should be completed by the installer to ensure
that no part of the installation has been overlooked.
• Proper installation is the responsibility of the homeowner.
The importance of proper installation of your Dacor range
cannot be overemphasized.
□ Has the plastic coating been peeled off the outside of the
range? Have all packaging materials been removed from
inside the oven?
□ Are all leveling legs extended down to make contact with the
floor? Is the unit level? See page 10.
□ Is the range secured in place with the provided anti-tip
bracket and foot according to these instructions? See pages
6 and 10.
□ Has the gas supply inlet pressure been measured to ensure
that it does not exceed the maximums stated in these
instructions. See page 3.
□ Is the range connected to the gas supply according to these
instructions and in accordance with all applicable codes? Did
the installer check the gas supply for leaks?
□ Is the oven door properly installed according to these
instructions? See page 10.
□ Have the burner knobs been installed in the proper locations?
See page 11.
□ Are the burners assembled and grates properly installed
according to these instructions? See page 12.
□ Has proper operation been verified? Has the warranty
been activated on-line or the warranty card been filled out
completely and mailed?
13
Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.com
Loading...