Dacor IF48NBOL, EF48DBSS, EF42NBSS, IF48DBOL, EF48NBSS User Manual

Use and Care Manual

42 Inch and 48 Inch

Built-in Refrigerators

For Use With Models:

EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS

IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL

Part No. 103674 Rev. D/W10159566

Style Varies

Model EF42DBSS Shown

Table of Contents

Important Safety Instructions ............................................1

Important Information .....................................................2

Model Identification .......................................................2

Before Use ....................................................................3

Refrigerator Operation .............................................. 3-12

Care and Cleaning ................................................. 13-14

Troubleshooting ...................................................... 15-17

Product Data Sheets .....................................................18

Warranty and Service ..................................................19

Notes ......................................................................... 20

© 2008 Dacor, all rights reserved

Important Safety Instructions

You

can be killed or seriously injured if you don't

follow

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Proper Disposal of Your Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous,
even if they sit out for “just a few days.” If you are getting rid of
your old refrigerator, please follow the instructions below to help
prevent accidents.

Before you throw away your old refrigerator or freezer:

Take off the doors. 

Leave the shelves in place so children may not easily climb 
inside.

1

Important Information

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this use and care manual for

future reference. This guide provides proper use and maintenance
information. Keep this guide and the sales receipt and/or

cancelled check in a safe place for future reference. Proof of
original purchase date is needed for warranty service.

IMPORTANT: If you receive a damaged product, immediately

contact your dealer or builder. Do not install or use a damaged
appliance.

If you have any questions, call:

Dacor Customer Service Team

1-800-793-0093 (U.S.A. and Canada)
Monday — Friday 6:00

Web site: www.Dacor.com

a m to 5:00 p m Pacific Time

Model Identification

Have complete model and serial number identification of your
refrigerator ready. These numbers are found on a serial number
label, located on the right side of the refrigerator liner. Record
these numbers on this page for easy access.

Model Number ________________________________________

Serial Number ________________________________________

Date of Purchase______________________________________

For service and warranty information, see page 19.

Since Dacor constantly improves the quality and performance of
our products, we may need to make changes to the appliance
without revising this manual.

EF42DBSS and EF48DBSS:

42” and 48” dispenser models

with all stainless steel finish

EF42NBSS and EF48NBSS:

42” and 48” non-dispensing

models with all stainless steel

finish

IF42DBOL and IF48DBOL:

42” and 48” dispenser models

designed for installation of

custom panels and handles

IF42NBOL and IF48NBOL:

42” and 48” non-dispensing

models designed for

installation of custom panels

and handles

2

Before Use

A. Top grille
B. Cabinet side trim

B BA

A. Power switch

A

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,
fire, or electrical shock.

WARNING

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

Remove the Packaging

If the ice storage bin is located on the door, remove the 
temporary shield from underneath the ice storage bin. See Ice
Maker and Storage Bin.

Remove tape and glue residue from surfaces before turning on 
the refrigerator. Rub a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable 
fluids or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see Important Safety Instructions on page 1.

Dispose of/recycle all packaging materials. 

Refrigerator Operation

Turning the Main Power Switch On/Off

Clean Before Using

After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions in
Care and Cleaning.

Important information to know about glass shelves and
covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter into
many small, pebble-size pieces. This is normal. Glass shelves
and covers are heavy. Use special care when removing them to
avoid impact from dropping.

Removing the Top Grille

Grasp both ends of the top grille.1.

Push the top grille straight up, then pull straight out. Lay the 2.
grille on a soft surface.

If you need to turn the power to your refrigerator on or off,
you must remove the top grille assembly to access the power
switch. Turn the power to the refrigerator off when cleaning your
refrigerator or changing light bulbs.

Replacing the Top Grille

Insert the top grille hooks (located on the back of the top grille) 1.
into the slots on the side trim.

Pull the grille down slightly to lock into place.2.

To Turn the Main Power Switch On or Off:

Remove the top grille.1.

Press the main power switch to the 2. ON or OFF position.

Replace the top grille.3.

IMPORTANT: Be sure the main
power switch is set to the On
position after cleaning refrigerator or
changing light bulbs.

3

Refrigerator Operation

Ice maker cover

Ice Maker

Water Supply Requirements

Read all directions before you begin.

IMPORTANT:

When your refrigerator was installed, the water connection 
from the water source should have been connected to your
refrigerator. If your refrigerator is not connected to a water
source, see Connect the Water Supply in the installation
instructions. If you have any questions about your water
connection, see the Troubleshooting section or call a licensed,
qualified plumber.

If you turn the refrigerator on before the water line is 
connected, turn the ice maker OFF. See Ice Maker and
Storage Bin on page 8.

All installations must meet local plumbing code requirements. 

Water Pressure

A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, see
Troubleshooting or call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of

a reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and 827
kPa).

If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 psi (276 kPa).

If the water pressure to the reverse osmosis system is less than
40 psi (276 kPa):

Check to see whether the sediment filter in the reverse 
osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill 
after heavy usage.

If your refrigerator has a water filter, it may further reduce 
the water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See Replacing the
Water Filter on page 14.

If you have questions about your water pressure, call a licensed,
qualified plumber.

Water System Preparation

Please read before using the water system.

Immediately after installation, follow the steps below to make
sure that the water system is properly cleaned.

Open the freezer door and turn off the ice maker. 1.

For non-dispensing models, lift the ice maker cover, then lift up
the wire shutoff arm as shown below.

For dispensing models, move the switch to the OFF (right)
setting as shown. The ON/OFF switch is located on the top
right side of the freezer compartment. See below.

NOTE: If your model has a base grille filter system, make sure
the base grille filter is properly installed and the cap is in the
horizontal position.

Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.

Use a sturdy container to depress the water dispenser bar 2.
until the water begins to flow. Flush the water system by
dispensing and discarding 6 qt (5.7 L) of water. Cleaning the
system will take approximately 3 to 4 minutes and will help
clear air from the line. Additional flushing may be required in
some households.

NOTE: As air is cleared from the system, water may spurt out
of the dispenser.

Open the freezer door and turn on the ice maker. For 3.
non-dispensing models, lower the wire shutoff arm. For
dispensing models, move the switch to the ON (left) position.

Allow 24 hours to produce the first batch of ice. 

Discard the first three batches of ice produced. 

Depending on your model, you may want to select the 
maximum ice feature to increase the production of ice.

4

Refrigerator Operation

Normal Operating Sounds

Your new refrigerator may make sounds that your old one
didn’t make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, such as the floor, walls and cabinets, can make the
sounds seem louder. The following describes the kinds of sounds
and what may be making them.

If your refrigerator is equipped with an ice maker, you will hear 
a buzzing sound when the water valve opens to fill the ice
maker for each cycle.

Your refrigerator is designed to run more efficiently to keep 
your food items at the desired temperatures and to minimize
energy usage. The high efficiency compressor and fans may
cause your refrigerator to run longer than your old one. You
may also hear a pulsating or high-pitched sound from the
compressor or fans adjusting to optimize performance.

You may hear the evaporator fan motor circulating air through 
the refrigerator and freezer compartments. The fan speed may
increase as you open the doors or add warm food.

Rattling noises may come from the flow of refrigerant, the 
water line or items stored on top of the refrigerator.

Water dripping on the defrost heater during a defrost cycle 
may cause a sizzling sound.

As each cycle ends, you may hear a gurgling sound due to the 
refrigerant flowing in your refrigerator.

Contraction and expansion of the inside walls may cause a 
popping noise.

You may hear air being forced over the condenser by the 
condenser fan.

You may hear water running into the drain pan during the 
defrost cycle.

Setting the Controls

The control panel is located inside the refrigerator compartment
on the ceiling.

IMPORTANT:

The refrigerator control adjusts the refrigerator compartment 
temperature. The freezer control adjusts the freezer
compartment temperature.

Wait 24 hours after you turn on the refrigerator before you put 
food into it. If you add food before the refrigerator has cooled
completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer controls to a
lower (colder) setting will not cool the compartments any
faster.

If the temperature is too warm or too cold in the refrigerator 
or freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.

The preset settings should be correct for normal household 
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.

The actual temperature may differ from the display when a 
door is open for an extended period of time.

NOTE: The factory recommended settings are 0°F (-18°C) for the
freezer and 37°F (3°C) for the refrigerator.

Turning the Refrigerator On or Off

Press and hold the  POWER ON-OFF key for 2 seconds.
When the refrigerator comes on, the freezer and refrigerator
temperature displays will light.

Ensuring Proper Air Circulation

In order to ensure proper temperatures, you need to permit
airflow between the two sections. Cold air enters the bottom of
the freezer section and moves up. It then enters the refrigerator
section through the top vent. Air then returns to the freezer as
shown.

Do not block any airflow vents. If the vents are blocked, airflow
will be obstructed and temperature and moisture problems may
occur.

IMPORTANT: Because air
circulates between both sections,
any odors formed in one section
will transfer to the other. You
must thoroughly clean both
sections to eliminate odors. To
avoid odor transfer and drying
out of food, wrap or cover foods
tightly.

To turn the refrigerator off, press and hold the  POWER
ON-OFF key for 2 seconds. The freezer and refrigerator
temperature displays will go dark when the refrigerator is off.

NOTE:

After the refrigerator is turned on, the Over Temperature Audio 
Alarm and indicator light will activate every 1½ hours until the
refrigerator and freezer temperatures are below 48°F (9°C)
and 15°F (-9°C), respectively, or until the alarm is turned off.
To turn off the audio alarm and indicator light, see Master
Alarm Reset on page 7.

Over Temperature

Indicator Light

The  Power ON-OFF key on the control panel shuts down the
cooling system, fans and compressors as well as the control
panel lights. To turn the power off completely, use the main
power switch located behind the top grille. See page 3.

5

Refrigerator Operation

Setting the Controls (continued)

Setting the Temperature Scale

The indicator light, next to the C° button, is lit when the 
temperature scale for the freezer and refrigerator displays is
set to Celsius. To change the displays to Celsius (or back to
Fahrenheit), press the C° button.

Celsius Indicator Light

Adjusting the Temperature Setting

NOTE: Wait at least 24 hours between adjustments. Re-check the
temperatures before other adjustments are made.

To adjust the temperature setting:

Press the refrigerator or freezer  UP () or DOWN () key
until the desired temperature is reached.

NOTE: The adjustable temperature range for the freezer is -5°F
to 6°F (-21°C to -14°C). The adjustable temperature range for the
refrigerator is 34°F to 46°F (1°C to 8°C).

Use the table below for guidance if you need to change the
temperature.

CONDITION/

REASON:

REFRIGERATOR too cold
Not set correctly for conditions

REFRIGERATOR too warm
High use or room very warm

FREEZER too cold
Not set correctly for conditions

FREEZER too warm/too little ice.
High use or heavy ice use

TEMPERATURE

ADJUSTMENT:

REFRIGERATOR Control 1°
higher

REFRIGERATOR Control 1° lower

FREEZER Control 1° higher

FREEZER Control 1° lower

Water Filter Monitor

Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.

The water filter monitor will help you know when it is time to
change your filter. To change the filter, see the Replacing the
Water Filter on page 14.

DISPLAY READING: STATUS:

99 percent New filter installed

10 percent Order replacement filter

0 percent or flow decreases Replace filter

A new water filter should display
a reading of 99%. The reading in
the display will decrease as the
filter life is used. When the display
reads 10%, it is time to order
a replacement water filter. It is
recommended that you replace the
filter when the filter display changes
to 0% OR when water flow to
your water dispenser or ice maker
decreases noticeably. See Replacing the Water Filter on page 14.

After replacing the water filter, press RESET and hold for 2
seconds to change the water filter display to 99 percent.

Max Cool

The Max Cool feature assists with periods of heavy ice usage, full
grocery loads or temporarily warm room temperatures.

Press the MAX COOL key to turn on the Max Cool feature.
The Max Cool indicator light will remain on for 24 hours unless
manually turned off.

NOTE: The refrigerator temperature display will remain at 34°F
(1°C) and the freezer temperature display will remain at -5°F
(-21°C) while the Max Cool feature is on. After 24 hours, the
refrigerator will automatically return to the previous temperature
settings.

Max Cool

Indicator Light

6

Refrigerator Operation

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

WARNING

Holiday Mode

The Holiday Mode feature is designed for the traveler or for
those whose religious observances require turning off the lights
and ice maker. When you select this feature, the ice maker will
be disabled and the interior lights will turn off. The temperature
settings remain unchanged. On some models, the Holiday Mode
feature doesn’t disable the ice and water dispenser. For these
models the lock button can be used to disable the ice and water
functions, but depressing the ice or water lever will still turn on
the dispenser light. For most efficient refrigerator operation, it
is recommended to exit the Holiday Mode when it is no longer
required.

Press the  HOLIDAY key to turn on the Holiday mode feature.
This feature will remain on until you press the HOLIDAY key
again.

Holiday Mode

Indicator Light

NOTE: If the Max Cool feature is selected prior to turning

on the Holiday mode, the temperature settings will remain
at 34°F (1°C) and -5°F (-21°C) for the refrigerator and
freezer compartments, until the Max Cool feature time (24
hours) is up. The refrigerator will then return to the previous
temperature settings chosen prior to turning on the Max Cool
feature, but the lights and ice maker will remain off until the
Holiday mode key is pressed again.

Alarms

Door Open

The Door Open indicator light will flash, an
alarm will sound and the interior lights will turn
off when a door has been open for longer than
10 minutes. When the door is closed, the audio alarm will reset
and turn off, but the Door Open indicator light will continue to flash
until the temperature is equal to or below 45°F (7°C) and 15°F
(-9°C) for the refrigerator and freezer compartments, respectively.

NOTE: To deactivate the audio alarm and indicator light, see
Master Alarm Reset.

Call Service

If the Call Service indicator light is flashing,
call for service. See the Warranty and Service
section for information.

NOTE: To deactivate the audio alarm and indicator light, see
Master Alarm Reset below.

Master Alarm Reset

Pressing the OVER TEMPERATURE RESET
key will shut off the audio alarm, but this
does not affect the indicator light the first time
OVER TEMPERATURE RESET is pressed.
The indicator light will shut off once OVER
TEMPERATURE RESET is pressed the
second time. The audio alarm will not sound
again for the current condition that caused
the alarm until a new condition occurs or until
a master alarm reset is performed.

A master alarm reset can be performed by pressing the POWER
ON-OFF key twice or by turning the power to the refrigerator
off and on again. See Turning the Main Power Switch On/Off
on page 3. The indicator light will reactivate after the OVER
TEMPERATURE RESET key is pressed if the condition that
caused the alarm is still present. See Over Temperature, Door
Open or Call Service above.

Over Temperature

The Over Temperature feature is designed to let you know when
either the refrigerator temperature rises above 48°F (9°C) or
the freezer temperature rises above 15°F (-9°C) for longer than
1½ hours. The audio alarm will shut off automatically when the
temperature returns to normal, but the indicator light will continue
to flash to let you know that an over temperature condition has
occurred.

If the over temperature condition is still present when an Over
Temperature Reset is performed, the indicator light will continue
to reactivate every 1½ hours until refrigerator and freezer
temperatures are below 48°F (9°C) and 15°F (-9°C), respectively.

IMPORTANT: If the Over Temperature Alarm activates, your
food may spoil. See the Power Interruption section on page 12.
Minimize door openings
until temperatures return
to normal.

NOTE: To deactivate the
audio alarm and indicator
light, see Master Alarm
Reset.

Over Temperature

Indicator Light

Water and Ice Dispensers

(Dispensing Models Only)

Depending on your model, you may have one or more of the
following options: the ability to select either crushed or cubed ice,
a special light that turns on when you use the dispenser, or a lock
option to avoid unintentional dispensing.

7

Refrigerator Operation

Ice maker cover

Water and Ice Dispensers

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer. When
the dispenser lever is pressed:

A trap door opens in a chute between the dispenser and the 
ice bin. Ice moves from the bin and falls through the chute.

When you release the dispenser lever, the trap door closes 
and the ice dispensing stops. The dispensing system will not
operate when the freezer door is open.

Some models dispense both cubed and
crushed ice. Before dispensing ice, select
which type of ice you prefer. The key
controls are designed for easy use and
cleaning.

For crushed ice, cubes are crushed before
they are dispensed. This may cause a slight
delay when dispensing crushed ice. Noise from the ice crusher is
normal, and pieces of ice may vary in size. When changing from
crushed to cubed, a few ounces of crushed ice will be dispensed
along with the first cubes.

To Dispense Ice:

If the ice storage bin is 1.
located on the door, remove
the temporary shield from
underneath the ice storage
bin. See Ice Maker and
Storage Bin.

Press button for the desired 2.
type of ice.

Press a sturdy glass against the ice dispenser lever. Hold 3.
the glass close to the dispenser opening so ice does not fall
outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the
lever in order to activate the ice dispenser. Pressing hard will
not make the ice dispense faster or in greater quantities.

Remove the glass to stop dispensing.4.

NOTE: The first few batches of ice may have an off-flavor from
new plumbing and parts. Throw the ice away. Also, take large
amounts of ice from the ice bin, not through the dispenser.

The Water Dispenser

If you did not flush the water
system when the refrigerator was
first installed, press the water
dispenser bar with a sturdy glass
or jar until you draw and discard
6 qt (5.7 L) or approximately 3
to 4 minutes of water after water
begins dispensing. It will take 2 to
3 minutes for the water to begin
dispensing. The water you draw and discard cleans the system
and helps clear air from the lines. Allow several hours for the
refrigerator to cool down and chill water.

IMPORTANT: Depending on your model, the small removable tray
at the bottom of the dispenser is designed to catch small spills
and allow for easy cleaning. There is no drain in the tray. The tray
can be removed from the dispenser and carried to the sink to be
emptied or cleaned.

To Dispense Water:

Press a sturdy glass against 1.
the water dispenser lever.

Remove the glass to stop 2.
dispensing.

NOTE: Water may have an
off-flavor if you do not use the
dispenser periodically. Dispense
enough water every week to
maintain a fresh supply.

Dispenser Light

The dispenser area has a light. It can be
turned on manually by pressing the ON key
(touch pad or rocker switch).

Whenever you use the dispenser, the lever
will automatically turn the light on also.

NOTE: See page 13 for information on
changing the dispenser light bulb.

Dispenser Lock

The dispenser can be turned off for easy
cleaning or to avoid unintentional dispensing
by small children and pets.

NOTE: The lock feature does not shut off
power to the refrigerator, to the ice maker, or
to the dispenser light. It simply deactivates
the dispenser levers.

To turn off the dispenser, press the  LOCK key. The indicator
will appear above the LOCK key and the ice and water
dispensers will not work.

To unlock the dispenser, press the  UNLOCK key until the
indicator appears. Then continue to dispense ice or water as
usual.

Ice Maker and Storage Bin

Non-Dispensing Models

To Turn the Ice Maker On or Off:

The On/Off switch for the ice maker is a wire shutoff arm located
on the side of the ice maker.

To turn the ice maker on, lift the ice maker cover, then lower 1.
the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice
is made, the ice cubes will fill the ice storage bin and the
ice cubes will raise the wire shutoff arm to the off (arm up)
position.

To manually turn the ice maker off, lift the wire shutoff arm to 2.
the off (arm up) position and listen for the click to make sure
the ice maker will not continue to operate.

8

Refrigerator Operation

A

B

A. Ice maker cover
B. Ice bin

Ice Maker

To Remove and Replace the Ice Bin (non-dispensing
models):

Flip up the ice maker cover.1.

Lift the wire shutoff arm so it clicks into the off (up) position. 2.
Ice can still be dispensed, but no more can be made.

Lift up the front of the storage bin and pull the ice bin forward.3.

Replace the bin by pushing it in all the way or the dispenser 4.
will not work. Push the wire shutoff arm down to the on
position to restart ice production. Make sure the door is closed
tightly.

Dispensing Models

To Turn the Ice Maker On/Off:

The On/Off switch is located on the top right side of the freezer 1.
compartment.

To turn the ice maker on, slide the control to the 2. ON (left)
position.

NOTE: Your ice maker has an automatic shutoff. The ice
maker sensors will automatically stop ice production, but the
control will remain in the ON (left) position.

To manually turn the ice maker off, slide the control to the 3. OFF
(right) position.

To Remove and Replace the Ice Storage Bin
(dispensing models):

Hold the base of the storage bin (located on the back of the 1.
freezer door) with both hands and press the release button to
lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to
the OFF (right) position when removing the storage bin. The
sensor cover (“flipper door”) on the left wall of the freezer
stops the ice maker from producing ice if the door is open or
the storage bin is removed.

Replace the storage bin on the door and push down to make 2.
sure it is securely in place.

Clean the Ice Storage Bin

Empty the ice container. Use warm water to melt the ice if 1.
necessary.

NOTE: Do not use anything sharp to break up the ice in the
bin or bucket. This can cause damage to the ice container and
the dispenser mechanism.

Wash ice bin with a mild detergent, rinse well and dry 2.
thoroughly. Do not use harsh or abrasive cleaners or solvents.

IMPORTANT:

Allow 24 hours to produce the first batch of ice. Allow 3 days 
to completely fill ice container. Discard the first three batches
of ice produced to avoid impurities that may be flushed out of
the system.

The quality of your ice will be only as good as the quality of 
the water supplied to your ice maker.

Avoid connecting the ice maker to a softened water supply. 

Water softener chemicals (such as salt) can damage parts of 
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.

It is normal for the ice cubes to be attached at the corners. 

They will break apart easily. 

For non-dispensing models, do not force the ice maker wire 
shutoff arm up or down.

Do not store anything on top of the ice maker or in the ice 
storage bin/bucket.

9

Refrigerator Operation

A. Ingredient care center

B. Crispers

B

A

Refrigerator Storage

Important information to know about glass shelves and
covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter into
many small, pebble-size pieces. This is normal. Glass shelves
and covers are heavy. Use special care when removing them to
avoid impact from dropping.

The shelves and compartments in your refrigerator are adjustable
and/or removable to meet your individual storage needs and to
make them easier to clean.

Storing similar food items together in your refrigerator and
adjusting the shelves compartments to fit different heights of
items will make finding the exact item you want easier. It will also
reduce the amount of time the refrigerator door is open, and help
save energy.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

Remove the shelf/frame by tilting it up at the front and lifting it 1.
out of the shelf supports. Pull the shelf straight out.

Replace the shelf/frame by guiding the rear shelf hooks into 2.
the shelf supports. Tilt the front of the shelf up until the rear
shelf hooks drop into the shelf supports.

Lower the front of the shelf and check to make sure that the 3.
shelf is securely in position.

Remove and Replace the Ingredient Care Center Cover:

Remove food from ingredient care center cover. Pull drawer 1.
out about 4” (10.16 cm). Reach under the glass shelf with both
hands and lift gently upward until back of shelf is free. Tilt shelf
at an angle and remove shelf from refrigerator being careful
not to bump the glass.

Replace the cover by holding the glass shelf firmly with both 2.
hands, tilt the shelf at an angle and position it above the
support rails. Place shelf gently on support rails on side wall.

Crispers and Covers

To remove and replace the crispers:

Slide the crisper drawer straight out to the stop. Lift the front 1.
of the drawer with one hand while supporting the bottom of the
drawer with your other hand and slide the drawer out the rest
of the way.

To replace the crisper drawer, place the drawer onto slides 2.
and push the drawer back until securely in position.

Carefully test the crisper drawer to make sure it has been 3.
replaced properly.

Ingredient Care Center)

The control for the ingredient care center (see location in diagram
at right) adjusts the storage temperature of the ingredient care
center pan. Cold air flows into the pan through the air duct
between the freezer and the refrigerator. Setting the controls
allows more or less cold air through the air duct.

To Adjust the Ingredient
Care Center:

Choose a setting based on the 1.
item to be stored in the pan.

Push the button that 2.
corresponds to that setting.

The indicator light for that 3.
setting will illuminate to verify
that the pan is ready to be
loaded.

To clean the crisper covers:

To clean the top crisper cover, remove the ingredient care center
located above it.

To clean the bottom crisper cover, first remove the top crisper
drawer.

10

Refrigerator Operation

Door Utility Bin

The utility bin can be placed in any position on the refrigerator
door.

To remove and replace the utility bin:

Remove the utility bin by grasping both ends and lifting 1.
compartment up and out.

Replace the bin by sliding it in above the desired support and 2.
pushing it down until it stops.

Gallon Door Bin

The adjustable gallon door bin can hold gallon size containers.

To install the gallon door bin:

NOTE: The gallon door bin can only be placed on the lower

support.

Position the gallon door bin above lowest door adjustment slot.1.

Push down to secure it.2.

Adjust other bins, as necessary to allow for milk or beverage 3.
container height.

Fresh Food Storage Information

The fresh food compartment of a refrigerator should be kept 
between 34°-40°F (1°-4°C) with an optimum temperature of
37°F (3°C).

Avoid overcrowding the refrigerator shelves. This reduces 
the circulation of air around the food and results in uneven
cooling.

Fruits and Vegetables

Storage in the crisper drawers traps humidity to help preserve 
the fruit and vegetable quality for longer time periods.

Sort fruits and vegetables before storage and use bruised or 
soft items first. Discard those showing signs of decay.

Always wrap odorous foods such as onions and cabbage so 
the odor does not transfer to other foods.

While vegetables need a certain amount of humidity to remain 
fresh, too much humidity can shorten storage times (especially
leafy vegetables). Drain vegetables well before storing.

Wait to wash fresh produce until right before use. 

Meat and Cheese

Raw meat and poultry should be wrapped securely so leakage 
and contamination of other foods or surfaces does not occur.

Occasionally mold will develop on the surface of hard cheeses 
(Swiss, Cheddar, Parmesan). In the interest of safety, discard
cheese that is moldy.

Dairy Food

Most dairy foods such as milk, yogurt, sour cream and cottage 
cheese have freshness dates on their cartons for appropriate
length of storage. Store these foods in the original carton and
refrigerate immediately after purchasing and after each use.

Standard Door Bins

The adjustable standard door bins can hold 2-liter bottles.

To remove and replace the door bins:

Remove the bin by lifting it up and pulling it out.1.

Replace the bin by sliding it in above the desired support and 2.
pushing it down until it stops.

Freezer Storage

Freezer Shelf

To remove and replace the shelf:

Remove the shelf by lifting it up and pulling it straight out.1.

Replace the shelf by putting it over the supports and lowering 2.
it into place.

11

Refrigerator Operation

Freezer Baskets

The freezer baskets can be used to store bags of frozen fruits and
vegetables that may slide off freezer shelves.

To remove and replace a freezer basket:

Pull the basket straight out to the stop.1.

Lift the front of the basket and slide it out the rest of the way.2.

Replace the basket by positioning it on the side wall guide 3.
rails. Lift the basket front slightly while pushing it past the
guide rail stops and slide basket in the rest of the way.

Frozen Food Storage Information

The freezer compartment of a refrigerator should be kept at 
approximately 0°F (-18°C).

A freezer operates more efficiently when it is at least two-thirds 
full.

Packaging Foods for Freezing

To minimize dehydration and quality deterioration use 
aluminum foil, freezer wrap, freezer bags or airtight containers.
Force as much air out of the packages as possible and be
sure they are tightly sealed. Trapped air can cause the food to
dry out, change color and develop an off-flavor (freezer burn).

Wrap fresh meats and poultry with suitable freezer wrap prior 
to freezing.

Do not refreeze meat that has completely thawed. 

Loading the Freezer

Avoid adding too much warm food to the freezer at one time. 
This overloads the freezer, slows the rate of freezing and can
raise the temperature of frozen foods.

Leave space between the packages so cold air can circulate 
freely, allowing food to freeze as quickly as possible.

Avoid storing hard-to-freeze foods such as ice cream and 
orange juice on the freezer door shelves. These foods are
best stored in the freezer interior where the temperature varies
less with door openings.

Power Interruptions

If the power will be out for 24 hours or less, keep the door or
doors closed to help food stay cold and frozen.

If the power will be out for more than 24 hours, do one of the
following:

Remove all frozen food and store it in a frozen food locker. 

Place 2 lbs (907 g) of dry ice in the freezer for every cubic foot 
(28 L) of freezer space. This will keep the food frozen for 2 to
4 days.

If neither a food locker nor dry ice is available, consume or 
can perishable food at once.

IMPORTANT: A full freezer stays cold longer than a partially filled
one. A freezer full of meat stays cold longer than a freezer full of
baked goods. If you see that food contains ice crystals, it may be
refrozen, although the quality and flavor may be affected. If the
condition of the food is poor, dispose of it.

Vacation Care

Your refrigerator is equipped with the Holiday mode, which is
designed for the traveler who wishes to turn off the lights and
ice maker. By selecting this feature, the temperature settings
remain unchanged, the ice maker will be disabled and the interior
lights will turn off. For most efficient refrigerator operation, it is
recommended to exit the Holiday mode when it is no longer
required.

If You Choose to Leave the Refrigerator On While
You’re Away:

Use up any perishables and freeze other items.1.

Press the 2. HOLIDAY key.

If your refrigerator has an automatic ice maker, 3.
shut off water supply to the ice maker.

Empty the ice bin.4.

When you return from vacation, press the 5.

HOLIDAY key to return to normal operation.

If You Choose to Turn the Refrigerator Off Before You
Leave:

Remove all food from the refrigerator.1.

If your refrigerator has an automatic ice maker:2.

Turn off the water supply to the ice maker at least one day 
ahead of time.

When the last load of ice drops, raise the wire shutoff arm 
to the OFF (up) position.

3. Turn the power off. See Turning the Refrigerator
On or Off on page 5.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both
doors to prop them open far enough for air to get
in. This stops odor and mold from building up.

12

Care and Cleaning

A. Dispenser Light

A

B. Light shield

B

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Cleaning

Important information to know about glass shelves and
covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter into
many small, pebble-size pieces. This is normal. Glass shelves
and covers are heavy. Use special care when removing them to
avoid impact from dropping.

Both the refrigerator and freezer sections defrost automatically.
However, clean both compartments about once a month to avoid
build-up of odors. Wipe up spills immediately.

To Clean Your Refrigerator:

Remove the top grille and turn off the main power switch. See 1.
Turning the Main Power Switch On/Off on page 3.

Remove all removable parts from inside, such as shelves, 2.
crispers, etc.

Hand wash, rinse, and dry removable parts and interior 3.
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.

Do not use abrasive or harsh cleaners such as window 
sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior and
door liners or gaskets. Do not use paper towels, scouring
pads or other harsh cleaning tools. These items can scratch
or cause damage.

To help remove odors, you can wash interior walls with a 
mixture of warm water and baking soda (2 tbs to 1 qt [26 g
to 0.95 L] of water).

Wash stainless steel and painted metal exteriors with a clean 4.
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners, or cleaners containing
chlorine. Dry thoroughly with a soft cloth. For additional
protection against damage to painted metal exteriors, apply
appliance wax (or auto paste wax) with a clean, soft cloth. Do
not wax plastic parts.

NOTE: To keep you stainless steel surfaces looking like new
and to remove minor scuffs or marks, you may use Dacor
Stainless Steel Cleaner. Use it according to the directions on
the bottle.

IMPORTANT: This cleaner is for stainless steel parts only!
Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If accidental contact does
occur, clean the plastic part with a sponge and mild detergent
in warm water. Dry thoroughly with a soft cloth.

Clean the condenser coils located behind the top grille 5.
ventilation panel regularly. Coils may need to be cleaned as
often as every other month. This may help save energy. Use
a vacuum cleaner with an extended attachment to clean the
condenser coils when they are dusty or dirty.

Turn the main power switch on and replace the top grille.6.

Changing the Light Bulbs

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure
to replace the bulb with one of the same size and shape. The
dispenser light requires a heavy duty 10-watt bulb. All other lights
require a 40-watt maximum appliance bulb. Replacement bulbs
are available from your Dacor dealer or appliance store.

Remove the top grille and turn off the main power switch. See 1.
Turning the Main Power Switch On/Off on page 3.

Remove light shield when applicable as shown.2.

NOTE: To clean a light shield, wash it with warm water and a
liquid detergent. Rinse and dry the shield well.

Remove light bulb and replace with one of the same size, 3.
shape and wattage.

Replace light shield when applicable as shown.4.

Turn the main power switch on and replace the top grille.5.

Dispenser Light (dispensing
models only)

Reach through the dispenser area
to remove and replace light bulb.

Refrigerator Control Panel Lights

Use a ¼” hex nut-driver to remove and replace the light shield.

Freezer and Crisper Lights

Remove the light shield by grasping the top and bottom and 
squeezing in toward the center. Once the hooks on the shield
are free from the freezer or crisper
lining, remove the shield.

Replace the light shield by 
squeezing the top and bottom
toward the center and inserting the
hooks into the slotted holes.

13

Care and Cleaning

WATER FILTER

CERTIFICATIONS

Replacing the Water Filter

Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.

Locate the water filter cap in the front base grille. Rotate the 1.
cap counterclockwise to a vertical position and pull the cap
and filter cartridge out through the base grille.

NOTE: There will be water in the filter. Some spilling may
occur.

Remove the cap by sliding it off the end of the used filter. The 2.
cap will slide to the left or right.

IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.

Flushing the Water System After Replacing Filter

Use a sturdy container to depress the water dispenser bar until
the water begins to flow. Flush the water system by dispensing
and discarding 6 qt (5.7 L) of water. Cleaning the system will take
approximately 3 to 4 minutes and will help clear air from the line.
Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of
the dispenser.

Take the new water filter out of its packaging and remove the 3.
protective cover from the O-rings. Discard the protective cover.

Slide the cap (removed in Step 2) onto the new filter. See 4.
illustration in Step 2.

With cap in the vertical position, push the new water filter into 5.
the base grille until it stops. Rotate the cap clockwise to a
horizontal position. Flush the water system. See Flushing the
Water System After Replacing Filter.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter. Your water will
not be filtered.

Remove the water filter.1.

Slide the cap off the end of the filter.2.

With the cap in the vertical position, insert the cap into the 3.
base grille until it stops.

IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.

Rotate the cap to a horizontal position. The cap might not be 4.
even with the base grille.

14

Troubleshooting

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,
fire, or electrical shock.

WARNING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Refrigerator will not operate

Is the power supply cord unplugged? Plug into a 
grounded 3 prong outlet.

Has a household fuse or circuit breaker tripped? Replace 
the fuse or reset the circuit breaker.

Is the refrigerator or freezer control turned to the OFF 
position? See Setting the Controls on page 5.

Is the refrigerator defrosting? Re-check to see if the 
refrigerator is operating in 30 minutes. Your refrigerator
will regularly run an automatic defrost cycle.

Temperature is too warm

Are the air vents blocked in either compartment? Blocked 
air vents obstruct cold air movement between the
compartments. Remove any objects from in front of the air
vents. See Ensuring Proper Air Circulation on page 5.

Are the door(s) opened often? The refrigerator will warm 
when this occurs. Keep the refrigerator cool by getting all
items out at one time, keeping food organized, and closing
the door as soon as possible.

Has a large amount of food just been added to the 
refrigerator or freezer? Adding a large amount of food
warms the refrigerator. It can take several hours for the
refrigerator to return to the normal temperature.

Are the controls set correctly for the surrounding 
conditions? See Setting the Controls on page 5.

Is the refrigerator not cooling? Turn the unit  OFF then ON
again to reset. See Setting the Controls on page 5. If the
problem is not corrected, call for service.

The lights do not work

Is a light bulb loose in the socket or burned out? See 
Changing the Light Bulbs on page 13.

Has the door been open more than 10 minutes? When 
the door is held open for more than 10 minutes, the Door
Open indicator light will flash and the interior lights will
shut off. See Door Open on page 7.

Is the refrigerator in Holiday mode? See Holiday Mode on 
page 7.

The refrigerator seems to make too much
noise

The sounds may be normal for your refrigerator. See 
Normal Operating Sounds on page 5.

The motor seems to run too much

Is the room temperature hotter than normal? The motor 
will run longer under warm conditions. At normal room
temperatures, expect your motor to run about 80% of the
time. Under warmer conditions, it will run even more.

Has a large amount of food just been added to the 
refrigerator? Adding a large amount of food warms the
refrigerator. The motor normally will run longer to cool the
refrigerator back down.

Are the doors opened often? If so, the motor will run 
longer. Conserve energy by getting all items out at one
time, keeping food organized, and closing the door as
soon as possible.

Are the controls not set correctly for the surrounding 
conditions? See Setting the Controls on page 5.

Are the doors not closed completely? Close the doors 
firmly. If they do not close completely, see The doors will
not close completely in this section.

Are the condenser coils dirty? This obstructs air transfer 
and makes the motor work harder. Clean the condenser
coils. Refer to the Care and Cleaning section.

Are the door gaskets not sealed all the way around? 
Contact a technician or other qualified person.

NOTE: Your new refrigerator will run longer than your old 
one due to its high-efficiency motor.

There is interior moisture buildup

Are the air vents blocked in the refrigerator? Remove any 
objects from in front of the air vents. See Ensuring Proper
Air Circulation on page 5.

Are the door(s) opened often? Avoid humidity buildup by 
getting all items out at one time, keeping food organized,
and closing the door as soon as possible.

Is the room humid? It is normal for moisture to build up 
inside the refrigerator when the room air is humid.

Is the food packaged correctly? Check that all food is 
securely wrapped. Wipe off damp food containers before
placing in the refrigerator.

Are the controls set correctly for the surrounding 
conditions? See Setting the Controls on page 5.

Was a self-defrost cycle completed? It is normal for 
droplets to form after the refrigerator self-defrosts.

Off-taste, odor or gray color in the ice

Are the plumbing connections new, causing discolored or 
off-flavored ice? Discard the first few batches of ice.

Have the ice cubes been stored too long? Throw old ice 
away and make a new supply.

Does the freezer and ice bin need to be cleaned? See the 
Care and Cleaning section or Ice Maker and Storage Bin
on page 8.

15

Troubleshooting

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

WARNING

Has food in the freezer or refrigerator been wrapped 
properly? Use airtight, moisture-proof packaging to avoid
odor transfer from stored food.

Does the water contain minerals (such as sulfur)? A filter 
may need to be installed to remove the minerals.

Is there a water filter installed on the refrigerator? Gray or 
dark discoloration in ice indicates that the water filtration
system needs additional flushing. Run additional water
through the water dispenser to flush the water filtration
system more thoroughly (at least 6 qt. [5.7 L] or 3 to 4
minutes initially). Discard discolored ice.

The ice maker is not producing ice or not
enough ice

Has the ice maker just been installed? The ice bin holds 
14 to 17 lbs (6.4 to 7.7 kg) of ice. The ice bin can take
three to four days to completely fill, if no ice is used.

Is the freezer temperature cold enough to produce ice? 
Wait 24 hours after ice maker hookup for ice production.
See Setting the Controls on page 5.

Is the ice maker wire shutoff arm in the off (arm up) 
position (on non-dispensing models)? Lower the wire
shutoff arm to the on (arm down) position. See Ice Maker
and Storage Bin in the operation section.

Is the ice maker switch in the OFF (right) position (on 
dispensing models)? Move ice maker switch to the
ON (left) position. See Ice Maker and Storage Bin in the
operation section.

Is the water line shutoff valve to the refrigerator turned 
on? Turn on the water valve. See Connect Water Supply in
the installation instructions.

Does the ice maker mold have water in it or has no ice 
been produced? Make sure your refrigerator has been
connected to a water supply and the supply shutoff valve
is turned on. See Connect Water Supply in the installation
instructions.

Is an ice cube jammed in the ice maker ejector arm? For 
models with an interior ice bin, remove the ice from the
ejector arm with a plastic utensil. For models with an ice
bin located on the freezer door, access the ice maker by
depressing the ice sensor door on the upper left side of
the freezer interior. While depressing the sensor door, lift
the ice maker service door and remove the ice from the
ejector with a plastic utensil. See Ice Maker and Storage
Bin in the operation section.

Has a large amount of ice just been removed? Allow three 
to four days for an empty ice bin to completely fill, if no
ice is used.

Are the controls set correctly? See  Setting the Controls on
page 5.

Is there a water filter installed on the refrigerator? The 
filter may be clogged or installed incorrectly. Check the
filter installation instructions to ensure that the filter
was installed correctly and is not clogged. If installation
or clogging is not a problem, call a qualified service
technician.

NOTE: If not due to any of the above, there may be a 
problem with the water line. Call for service.

The ice dispenser will not operate properly

If the ice storage bin is located on the door, remove the 
temporary shield from underneath the ice storage bin. See
Ice Maker and Storage Bin on page 8.

Is the freezer door closed completely? Push the door 
firmly shut. If it will not shut all the way, see The doors will
not close completely in this section.

Is the ice bin installed correctly? For models with an 
interior ice bin, push the ice bin in all the way. If the
ice bin does not go in all the way, it may not be put in
straight. Pull it out and try again. For models with an ice
bin located on the freezer door, the bin should sit level. To
remove the bin, press the release button on the right side
of the bin and lift straight up.

Replace the bin in the door making sure it is properly 
aligned and snapped securely into place. See Ice Maker
and Storage Bin on page 8.

Has the wrong ice been added to the bin? Use only cubes 
produced by the current ice maker. If other cubes have
been added, remove all cubes and check to see that none
have become stuck in the delivery chute.

Has the ice frozen in the ice bin? Shake the ice bin to 
separate cubes. If cubes do not separate, empty bin and
wait 24 hours for ice to restock.

Has the ice melted around the auger (metal spiral) in 
the ice bin? Dump the ice cubes and clean the ice bin
completely. Allow 24 hours for the ice maker to restock.
Do not try to remove the melted ice with a sharp object.
You could damage the ice bin.

Is ice stuck in the delivery chute? Clear the ice from the 
delivery chute with a plastic utensil. Do not use anything
sharp to remove the ice. You could cause damage.

Is the ice dispenser stalling while dispensing “crushed” 
ice? Stop dispensing ice. Change the ice button from
“crushed” to “cubed.” Depress the ice dispenser arm
using a sturdy glass. If cubed ice dispenses correctly,
depress the button for “crushed” ice and begin dispensing
again. See Water and Ice Dispensers on page 8.

Is there ice in the bin? See  The ice maker is not producing
ice earlier in this section.

Has the dispenser arm been held in too long? Release 
dispenser arm. Ice will stop dispensing when the arm is
held in too long. Wait three minutes for dispenser motor to
reset before using again. It is best to take large amounts
of ice directly from the ice bin, not through the dispenser.

16

Troubleshooting

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

WARNING

The ice storage bin is difficult to remove

Is the ice storage bin difficult to remove (on some 
models)? For models with an ice storage bin located on
the freezer door, select “cubed” ice. Using a sturdy glass,
quickly depress and release the ice dispenser lever. Open
the freezer door, depress the release button on the ice
storage bin and lift upward. See Ice Maker and Storage Bin
on page 8.

The water dispenser will not operate properly

Has the water system not filled? The water system needs 
to be filled the first time it is used. Use a sturdy container
to depress the water dispenser bar until the water begins
to flow. Flush the water system by dispensing and
discarding 6 qt (5.7 L) of water. Cleaning the system will
take approximately 3 to 4 minutes and will help clear air
from the line. Additional flushing may be required in some
households. See Water and Ice Dispensers on page 8.

Is the water shutoff valve not turned on or the water line 
connected at the source? Make sure the water shutoff
valve is turned on and the water source is connected
to the refrigerator. See Connect Water Supply in the
installation instructions.

Is the water shutoff valve clogged or incorrectly installed? 
See Connect Water Supply in the installation instructions.
If clogging or installation is not a problem, call for service
or contact a plumber.

Is there a kink in the home water source line? If you find 
or suspect a kink in the water line, call for service.

Is there a water filter installed on the refrigerator? The 
filter may be clogged or incorrectly installed. First, check
the filter installation instructions to ensure that the filter
was installed correctly and is not clogged. If installation or
clogging is not a problem, call for service.

Water is leaking from the dispenser

Glass not being held under the dispenser long enough? 
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.

Is there a water filter installed on the refrigerator? The 
water filtration system may have air in the lines, causing
water to drip. Additional flushing may help clear air from
the lines. Normal dispenser use should flush air from the
lines within 24 to 72 hours.

Water flow from the dispenser decreases
noticeably

Is there a water filter installed on the refrigerator? The 
filter may be full or incorrectly installed. Remove the water
filter cartridge. See Replacing the Water Filter on page

14. Operate the dispenser. If the water flow increases
noticeably, replace the filter.



The doors will not close completely

Are food packages blocking the door open? Rearrange 
containers so that they fit more tightly and take up less
space.

Is the ice bin out of position? For models with an interior 
ice bin, push the ice bin in all the way. If the ice bin does
not go in all the way, it may not be put in straight. Pull it
out and try again. For models with an ice bin located on
the freezer door, the bin should sit level. To remove the
bin, press the release button on the right side of the bin
and lift straight up. Replace the bin in the door making
sure it is properly aligned and snapped securely into
place. See Ice Maker and Storage Bin on page 8.

Are the pans, shelves, bins, or baskets out of position? 
Put the crisper cover and all pans, shelves, bins, and
baskets back into their correct positions. See Crisper and
Covers on page 10.

Does the refrigerator wobble or seem unstable? Level the 
refrigerator. See Adjust Doors and Level Refrigerator in the
installation instructions.

The doors are difficult to open

Are the gaskets dirty or sticky? Clean gaskets according 
to the directions in the Care and Cleaning section.

The dispenser water is not cool enough

Has the refrigerator been newly installed? Allow 24 hours 
for the refrigerator to cool completely.

Has a large amount of water been recently dispensed? 
Allow 24 hours for the water to cool completely.

Has water not been recently dispensed? The first glass of 
water may not be cool. Discard the first glass of water.

The divider between the two compartments is warm. 
The warmth is probably due to normal operation of the
automatic exterior moisture control. If still concerned, call
for service.

17

Product Data Sheets

Base Grille Water Filtration System (Water Filter)

Model WF-LC400V/LC400V Capacity 400 Gallons (1514 Liters)

Tested and certified by NSF International against ANSI/NSF Standard 42 for
the reduction of Chlorine Taste and Odor, Particulate Class I*; and against
ANSI/NSF Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene,
Toxaphene, p-dichlorobenzene, 2, 4-D, Cysts, Turbidity and Asbestos.

This system has been tested according to ANSI/NSF 42/53 for the reduction of the substances listed below. The concentration of the
indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water
leaving the system, as specified in ANSI/NSF 42/53.

Substance Reduction
Aesthetic Effects

Chlorine Taste/Odor
Particulate Class 1*

Contaminant
Reduction

Lead: @ pH 6.5
Lead: @ pH 8.5

Mercury: @ pH 6.5
Mercury: @ pH 8.5

Benzene 0.005 mg/L 0.0162 mg/L 0.015 ± 10% 0.0005 mg/L 0.001 mg/L 96.3% 96.3%

p-dichlorobenzene 0.075 mg/L 0.220 mg/L 0.225 ± 10% 0.0005 mg/L 0.0005 mg/L 99.7% 99.7%

Toxaphene 0.003 mg/L 0.014 mg/L 0.015 ± 10% 0.0014 mg/L 0.001 mg/L 90% 92.96%

Atrazine 0.003 mg/L 0.0086 mg/L 0.009 mg/L ± 10% 0.0005 mg/L 0.0005 mg/L 94.25% 94.25%

2, 4-D 0.07 mg/L 0.197 mg/L 0.210 ± 10% 0.058 mg/L 0.0137 mg/L 70.6% 93.06%

Asbestos 99% 26 x 107 107 to 108 fibers/L†† 0.18 x 107 mg/L 0.18 x 107 mg/L 99.93% 99.93%

Cysts‡
Turbidity

NSF Reduction
Requirements

≥50%
≥85%

NSF Reduction
Requirements

0.01mg/L

0.01mg/L

0.002 mg/L

0.002 mg/L

99.95%

0.5 NTU

Average
Influent

2.1 mg/L
5,366,667/mL

Average
Influent

0.152 mg/L†

0.143 mg/L†

0.0061 mg/L

0.0057 mg/L

111,000/mL

11.00 NTU

Influent Challenge
Concentration

2.0 mg/L ± 10%
At least 10,000
particles/mL

Influent Challenge
Concentration

0.15 mg/L ± 10%

0.15 mg/L ± 10%

0.006 mg/L ± 10%

0.0058 mg/L ± 10%

50,000/L min.
11 ± 1 NTU

Maximum
Effluent

0.06 mg/L
4,100/mL**

Maximum
Effluent

0.001 mg/L

0.001 mg/L

0.0004 mg/L

0.0008 mg/L

1 mg/L

0.40 NTU

Average
Effluent

0.05 mg/L
2,300/mL

Average
Effluent

0.001 mg/L

0.001 mg/L

0.0003 mg/L

0.00051 mg/L

1 mg/L

0.35 NTU

Minimum %
Reduction

97.1%

99.3%

Minimum %
Reduction

99.34%

99.30%

93.5%

85.8%

99.99%

96.4%

Average %
Reduction

97.6%

99.9%

Average %
Reduction

99.34%

99.30%

96.7%

91.2%

99.99%

96.8%

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 63°F
(17.2°C).

It is essential that operational, maintenance, and filter 
replacement requirements be carried out for the product to
perform as advertised.

Model WF-LC400V  The filter monitor system measures the
amount of water that passes through the filter and alerts you
to replace the filter. When 90% of the filter’s rated life is used,
the filter indicator light changes from green to yellow. When

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 30 - 120 psi (207 - 827 kPa)

Water Temperature 33° - 100°F (0.6° - 37.8°C)

Service Flow Rate 0.5 GPM (1.89 L/min.) @ 60 psi.

100% of the filter’s rated life is used, the filter indicator light
changes from yellow to red, and it is recommended that you
replace the filter.

The product is for cold water use only. 

 Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used
on disinfected waters that may contain filterable cysts.

* Class I particle size: >0.5 to <1 um
** Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
† These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.
†† Fibers greater than 10 um in length
‡ Based on the use of Cryptosporidium parvum oocysts
® NSF is a registered trademark of NSF International.

18

Warranty and Service

Product Maintenance

Do not perform any maintenance other than that instructed in the
Care and Cleaning section of this manual. A qualified service
technician should perform all other service.

Getting Help

Before you obtain service, please review the Troubleshooting
section of this manual. If you have performed the checks in the
Troubleshooting section and the problem has not yet been
remedied, please visit our web site or contact the Dacor Customer
Service Team for a listing of Dacor authorized service agents.
Before requesting service, become familiar with the warranty
terms and conditions on this page.

Contact us through our web site at:

www.Dacor.com

Dacor Customer Service Team:

Tel: [phone]
Fax: [phone]
Business Hours: 6:00 a.m. - 5:00 p.m. Pacific Time

You may also write us at:

Dacor Customer Service Team
1440 Bridge Gate Drive
Diamond Bar, CA 91765

At Dacor, we believe that our quality of service equals that of
our product. Should your experience with our service network
or product be different, please contact our Customer Service
Team and share your encounter with us. We will do our utmost to
resolve the situation for you and deliver on our Dacor promise. If
you need anything clarified, just let us know.

What is Covered

CERTIFICATE OF WARRANTIES DACOR REFRIGERATORS

WITHIN THE FIFTY STATES OF THE U.S.A., THE DISTRICT OF
COLUMBIA AND CANADA*:

TWO YEAR LIMITED WARRANTY

For two years from the date of purchase, when this major
appliance is operated and maintained according to instructions
attached to or furnished with the product, Dacor will pay for
factory specified parts and repair labor to correct defects in
materials or workmanship. Service must be provided by a Dacor
designated service company.

LIMITED WARRANTY

Major Refrigeration Components

In the third through sixth years from the date of purchase, when
this major appliance is operated and maintained according to
instructions attached to or furnished with the product, Dacor will
pay for factory specified parts and repair labor costs to correct
defects in materials or workmanship in the sealed refrigeration
system. These parts are: compressor, evaporator, condenser,
dryer, and connecting tubing. Service must be provided by a
Dacor designated service company.

In the seventh through twelfth years from date of purchase, when
this major appliance is operated and maintained according to
instructions attached to or furnished with the product, Dacor will
pay for factory specified parts to correct defects in materials or
workmanship in the sealed refrigeration system. These parts are:
compressor, evaporator, condenser, dryer, and connecting tubing.

LIMITED WARRANTY

Water Filter, if equipped

30 day limited warranty on water filter. For 30 days from the date
of purchase, when this filter is operated and maintained according
to instructions attached to or furnished with the product, Dacor
will pay for replacement parts to correct defects in materials and
workmanship.

NOTE

The full warranty and the limited warranties apply when
the refrigerator is located in the United States or Canada.
Refrigerators located elsewhere are covered by the limited
warranties only including parts that fail during the first year.

CANADIAN RESIDENTS

The above warranties only cover an appliance installed in Canada
that has been certified or listed by appropriate test agencies
for compliance to a National Standard of Canada unless the
appliance was brought into Canada due to transfer of residence
from the United States to Canada.

LIMITATIONS OF LIABILITY

The warrantor shall not be liable for any incidental or
consequential damages, including food loss. Some states do not
allow the exclusion or limitation of consequential damages, so the
above limitation or exclusion may not apply to you.

What is Not Covered

Conditions and damages resulting from any of the following:1.

Improper installation, delivery, or maintenance. 

Any repair, modification, alteration, or adjustment not 
authorized by the manufacturer or an authorized servicer.

Misuse, abuse, accidents, or unreasonable use. 

Incorrect electric current, voltage, or supply. 

Improper setting of any control. 

Warranties are void if the original serial numbers have been 2.
removed, altered or cannot be readily determined.

Light bulbs.3.

Products purchased for commercial or industrial use.4.

The cost of service or service call to:5.

Correct installation errors. 

Instruct the user on the proper use of the product. 

Transport the appliance to the servicer. 

Consequential or incidental damages sustained by any person 6.
as a result of any breach of these warranties. Some states
do not allow the exclusion or limitation of consequential or
incidental damages, so the above exclusion may not apply.

19

Notes

20

Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: [phone] ● FAX: [phone] ● www.Dacor.com