
Document # PG01-015
RNO, RNOV
Revised 11/25/14 Page 1/3
Renaissance® 27” and 30” Wide
Single Wall Ovens
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
Top of
K
Utility
cutout
C
A
chassis
B
PLANNING
GUIDE
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
F
G
H
D
accompanying installation instructions.
2 3/8”
(6.0 cm)
1 7/8”
(4.8 cm)
Conduit:
60” (152 cm)
Control panel
front
L
E
M
Top of
chassis
long
Control panel
side view
Model
RNO[V]127
21 1/2”
(54.6) cm
RNO[V]130
* To top of chassis notch behind control panel
Epicure
(Order kit #AROVH30S)
Handle Dimensions
ELECTRICAL SPECIFICATIONS
Model
RNO[V]127
RNO[V]130
*** Two 120 Vac hot (L1 and L2), one neutral, one ground
The above specifications are for reference only. See the appliance data
plate for exact specifications.
(A) Overall
Width
26 7/8”
(68.3 cm)
29 7/8”
(75.9 cm)
Dedicated Circuit
Requirements
240 Vac 60 Hz., 4-wire,***
240 Vac 60 Hz., 4-wire,***
(B) Chassis
Width
25 1/2”
(64.8 cm)
28 1/2”
(72.4 cm)
30 Amp.
30 Amp.
Millennia
(C) Overall
Height
27 3/4”
(70.5 cm)
27 3/4”
(70.5 cm)
Flush
Total Connected Load
240 Vac 60 Hz,
19.0 Amp., 4.7 kW
240 Vac 60 Hz,
24.5 Amp., 6.0 kW
(D)* Chassis
Height
27 3/8”
(69.5 cm)
27 3/8”
(69.5 cm)
(E) Control
Panel
Overlay
3/8”
(1.0 cm)
3/8”
(1.0 cm)
(F) Utility
Cutout Width
6 1/2”
(16.5 cm)
* 7/8” (2.2 cm) for models RNO[V]127B, RNO[V]130B, RNO127W and RNO130W
All specications subject to change without notice.
(G) Utility
Cutout Height
5”
(12.7 cm)
(H) Utility
Cutout Depth
7 7/8”
(20.0 cm)
(J) Control
Panel Depth
3/4” *
(1.9 cm)
(K) Chassis
Depth
24”
(61.0 cm)
(L) Control
Panel Notch
Depth
1/2”
(1.3 cm)
(M) Notch
Height
3/4”
(1.9 cm)
Phone: (800) 793-0093www.dacor.com

Document # PG01-015
RNO, RNOV
Revised 11/25/14 Page 2/3
Renaissance 27” and 30” Wide,
Single Wall Oven
Cabinet tolerances: +1/16” (+1.6 mm) -0, unless otherwise stated
36” typ.
(91.4 cm)
N
Recommended
electrical
1” (2.5 cm) min.
location
to bottom of
cabinet door
CUTOUT DIMENSIONS - STANDARD UNDER COUNTER INSTALLATION
1 1/2”
(3.8 cm)
typical counter
PLANNING
GUIDE
1“ (2.5 cm) min. to combustibles
R
P
3/4” (1.9 cm)
support platform
SINGLE WALL OVEN
Minimum interior cabinet depth: 24” (61.0 cm)
1“ (2.5 cm) min.
to combustible floor
Recommended
electrical
location
4” typical toe kick
Model
RNO[V]127
RNO[V]130
R
P
1” (2.5 cm) min.
to top of
cabinet door
4” typical toe kick
CUTOUT DIMENSIONS - STANDARD WALL INSTALLATION
Alternate
electrical
SINGLE WALL OVEN
support platform
location
3/4” (1.9 cm)
31 1/4” (79.4 cm)
recommended
(N) Minimum
Cabinet
Width
27”
(68.6 cm)
30”
(76.2 cm)
(P) Cutout Width
25 5/8” (65.1 cm)
minimum (recommended)
26 1/8” (66.4 cm)
maximum
28 5/8” (72.7 cm)
minimum (recommended)
29 1/8” (74.0 cm)
maximum
(R) Minimum Cutout
Height
27 1/2”
(69.9 cm)
27 1/2”
(69.9 cm)
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com

Document # PG01-015
RNO, RNOV
Revised 11/25/14 Page 3/3
Renaissance 27” and 30” Wide,
Single Wall Oven
CUTOUT DIMENSIONS - FLUSH INSTALLATION
SINGLE WALL OVEN
Cabinet tolerances: +1/16” (+1.6 mm) -0, unless otherwise stated
PLANNING
GUIDE
T
Finished
stops *
TOP VIEW
U
W
V
X
VENTILATION
INSET
3/4” (1.9 cm)
Cabinet
face
1” (2.5 cm) **
** 1 1/8” (2.9 cm) for models
RNO[V]127B, RNO[V]130B,
RNO127W, RNO130W
SIDE VIEW
Model
RNO127[F]S 24 3/4” (62.9 cm) 27” (68.6 cm) 27 7/8” (70.8 cm) 3/4” (1.9 cm) 3/8” (1.0 cm)
RNO130[F]S 24 3/4” (62.9 cm) 30” (76.2 cm) 27 7/8” (70.8 cm) 3/4” (1.9 cm) 3/8” (1.0 cm)
RNO[V]127B, RNO127W 24 7/8” (63.2 cm) 27” (68.6 cm) 27 7/8” (70.8 cm) 7/8” (2.2 cm) 3/8” (1.0 cm)
RNO[V]130B, RNO130W 24 7/8” (63.2 cm) 30” (76.2 cm) 27 7/8” (70.8 cm) 7/8” (2.2 cm) 3/8” (1.0 cm)
* Back of wall oven control panel rests against stops
(T) Minimum
Cabinet Depth
(U) Cutout
Width
(V) Cutout
Height
FRONT VIEW
(W) Stop Depth (X) Stop Width
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com