Dacor DR30GIFS User Manual 2
Document # PGCI-028
Rear wall or
countertop edge
countertop opening
29 1/4” (74.3 cm)
30” (76.2 cm)
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
overhang to width of
cabinets
3/8” (9.5 mm) min.
countertop overhang
3”
(7.6 cm)
10” min. (25.4 cm)
to any combustibles
above counter both sides
Countertop overhang
1 5/8” (4.1 cm) max.
24 1/8”
(61.3 cm)
raised vent opening
27 1/2” (69.9 cm)
COMBINATION INSTALLATIONS
Revised 10/07/13 Page 1/1
DR30GI[F]S Range with ERV3015
PLANNING
Raised Vent
RAISED VENT (SELF-RIMMING) INSTALLATION CUTOUT OPTIONS (MODELS DR30GIS AND DR30GIFS ONLY)
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
For all installations with a raised vent:
Countertop height: 34 3/4” (88.3 cm) min.
Countertop thickness: 1 5/8” (4.1 cm) max.
NOTE: For all raised vent installations, use only Dacor raised vent model
ERV3015. This configuration is not compatible with cabinet blower model
CABP3.
10” min. (25.4 cm)
to any combustibles
above counter both sides
36 7/8” (93.7 cm) max.
Rear wall or
countertop edge
3/8” (9.5 mm) min.
countertop overhang
27 1/2” (69.9 cm)
raised vent opening
29 1/4” (74.3 cm)
countertop opening
30” (76.2 cm)
cabinet opening
1
20 5/8”
(52.4 cm)
3”
(7.6 cm)
below countertop
Cabinet face
below countertop
Notch countertop
overhang to width of
cabinets
Countertop overhang
1 5/8” (4.1 cm) max.
PARTIAL SIDE PANELS INSTALLED (TOP VIEW)
24” - 24 1/4” CABINET DEPTH
2, 3
10” min. (25.4 cm)
to any combustibles
above counter both sides
3/8” (9.5 mm) min.
countertop overhang
Rear wall or
countertop edge
3” (7.6 cm)
Wall
Stiffener
ERV3015
raised vent
IMPORTANT: If optional side panels are not installed cabinet
3/8” min. (1.0 cm) flat countertop
overhang required behind cutout
29 1/2” (74.9 cm)
Back of
DR30GI[F]S
range
Shown with partial
side panel installed
3/8” min. (1.0 cm)
space behind raised vent
chassis to clear stiffener
face must be flush with back of control panel.
SIDE VIEW - DR30GI[F]S RANGE AND
ERV3015 RAISED VENT
control panel
Cabinet face
GUIDE
Countertop
25 3/4”
(65.4 cm)
max.
Countertop
1
To create a “built-in look” on the front of the cabinet, this dimension may be changed to 29 1/4” (74.3 cm). Width notches remains 30”.
2
For 24 to 24 1/4 inch deep cabinets, the side panels and control panel will protrude from the cabinet face a total of 5 5/8 inches.
3
Revision A ranges only: Raised vent trim piece and 3 1/2 inch side panels (Dacor PN ADTK30GSR24) must be installed to cover the
front of the raised vent chassis in back and range chassis on sides.
4
Revision A ranges only: Optional raised vent trim piece (Dacor PN ADTK30GSR) must be installed to cover the front of the raised
vent chassis in back.
front
24 1/4” - 27 1/2” CABINET DEPTH
PARTIAL SIDE PANELS INSTALLED (TOP VIEW)
All specications subject to change without notice.
27 1/2” (69.9 cm)
raised vent opening
29 1/4” (74.3 cm)
countertop opening
30” (76.2 cm)
cabinet opening
below countertop
Notch countertop
overhang to width of
cabinets
Cabinet face
below countertop
1 1
20 7/8”
20 5/8”
(52.4 cm)
(53.0 cm)
to
24 1/8”
(61.3 cm)
4
CUSTOM CABINET 27 1/2” OR DEEPER,
PARTIAL SIDE PANELS REMOVED (TOP VIEW)
4
Phone: (800) 793-0093www.dacor.com
Loading...