Page 1
DR30ES, DR30EFS, DR30EIS, DR30EIFS
1” (2.5 cm)
Front of open door
Front of handle/knobs
Front panel
Rear of front panel
Backguard thickness
3” (7.6 cm)
backguard*
External handle
shown, some models
have integral handle
(see inside cover)
6” (15.2 cm)
backguard*
*
See table for compatibility
Product width:
29 15/16” (76.0 cm)
35”
(88.9 cm)
to
37”
(94.0 cm)
9” (22.9 cm)
Backguard*
A
B
C
D
DR30EI[F]S:
3/8” (9.5 mm)
DR30E[F]S:
Full stainless
steel side panels
DR30EI[F]S:
3” (7.6 cm)
partial stainless
steel side panels
(removable)
Document # PG05-008
Product Dimensions
All tolerances ±1/16” (±1.6 mm) unless otherwise noted.
Distinctive
™
Electric Ranges
Revised 10/30/12 Page 1/4
30” Wide
PLANNING
GUIDE
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
Part Number Description Compatibility
ADRB30E03 3 Inch Optional on all models
All specications subject to change without notice.
Models DR30EIS and DR30EIFS come equipped from the factory with flat stainless trim piece in place
of a backguard. A backguard may be purchased as an optional accessory.
The trim on models DR30ES and DR30EFS are not compatible with a raised vent.
Models DR30EIS and DR30EIFS are compatible with Dacor raised vent models ERV3015. Use only
theses specified raised vent models.
ADRB30E06 6 Inch
ADRB30E09 9 Inch Optional on all models
OVERALL DEPTH DIMENSIONS - SIDE VIEW
AVAILABLE BACKGUARDS
Standard on models DR30ES, DR30EFS
Optional on models DR30EIS, DR30EIFS
Dimension
A 46 1/8” (117.2 cm) 46” (116.8 cm)
B 27 3/4” (70.5 cm) 27 5/8” (70.2 cm)
C 25 3/8” (64.5 cm) 25 1/4” (64.1 cm)
D 23 1/4” (64.1 cm) 23 1/8” (58.7 cm)
DR30ES
DR30EIS
Phone: (800) 793-0093www.dacor.com
DR30EFS
DR30EIFS
Page 2
Document # PG05-008
DR30ES, DR30EFS, DR30EIS, DR30EIFS
Revised 10/30/12 Page 2/4
Distinctive 30” Wide
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
B
13” (33.0 cm)
4
max.
18” (45.7 cm)
min.
Note 2
4
Non-combustible
surface along
back wall
recommended
Note 1
A
Electric Ranges
Top of
finished
counter
Note 5
Suggested
location of
3
utilities
PLANNING
GUIDE
■ Failure to meet or exceed the maximum and
minimum dimensions/clearances stated may result
in a fire hazard.
■ The shaded area shown denotes the location of
the electrical junction box/receptacle. This is the
suggested location. For replacement purposes, the
location of the existing electrical supply may be
utilized provided that it does not interfere with the
sides or rear of the range.
■ Access to the remote circuit breaker panel/fuse box,
with the range in place and operating, must also be
allowed for in the installation.
■ The electrical junction box/receptacle must be
located so that it does not interfere with the range
when it is installed and under operation. In addition,
the junction box/receptacle must be located so
the range can be removed for service and remain
connected to power.
■ To eliminate the risk of burns or fire by reaching
over heated surface units, cabinet storage space
located above surface units should be avoided. If
cabinet storage space is to be provided directly
above the range, the risk of personal injury may be
reduced by installing a range hood.
■ In all instances, installation of a range hood is highly
recommended. The hood should project horizontally
a minimum of five (5) inches beyond the face of
the cabinets. See the range hood specifications for
minimum clearances.
■ The range may be installed flush to the rear wall.
See diagram and notes for rear wall surface
requirements. It is not necessary to install noncombustible materials behind the range below the
countertop height.
■ Any openings in the wall behind the appliance or in
the floor underneath it must be sealed.
C
FREESTANDING INSTALLATION CABINET CUTOUT DIMENSIONS - MODELS DR30ES, DR30EFS, DR30EIS AND DR30EIFS
1
30” (76.2 cm) min. vertical clearance from top of range grates to bottom of uncovered wood or metal cabinet. 24” (61 cm) min. clearance if bottom of wood
or metal cabinets are protected by not less than 1/4“ (0.6 cm) flame retardant millboard covered with no less than No. 28 MSG sheet steel 0.015” (0.04
cm) stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper. 30” (76.2 cm) min. clearance between top of range grates and bottom of
unprotected wood or metal cabinet. If installing range hood, check the hood specifications for minimum required clearances.
2
Cabinet/countertop depth is at discretion of customer but cabinet face SHALL NOT protrude further than rear of front panel. See Product Dimensions.
3
Consult local code and following pages for requirements.
4
This specification not applicable for cabinets more than a horizontal distance of 10” (25.4 cm) from edge of range.
5
10” (25.4 cm) min. to combustible sidewalls above range (both sides).
All specications subject to change without notice.
A* B
30 1/16” min.
(76.4 cm)
* See the cutout dimensions on following page for self-rimming installations.
36” (91.4 cm) recommended
30” (76.2 cm) min.
C
37” (94.0 cm)
max.
Phone: (800) 793-0093www.dacor.com
Page 3
Document # PG05-008
Rear wall or
countertop edge
countertop opening
29 1/4” (74.3 cm)
30 1/16” (76.2 cm)
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
to width of cabinets
3/8” min. (9.5 mm)
countertop overhang
10” min. (25.4 cm)
to any combustibles
above counter both sides
19 7/8”
(50.5 cm)
to
22 7/8”
(58.1 cm)
19 7/8”
(50.5 cm)
24 1/2”
(62.2 cm)
max.
Countertop front
Rear wall or
countertop edge
countertop opening
29 1/4” (74.3 cm)
30 1/16” (76.2 cm)*
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
to width of cabinets
3/8” min. (9.5 mm)
countertop overhang
10” min. (25.4 cm)
to any combustibles
above counter both sides
22 7/8”
(58.1 cm)
24 1/2”
(62.2 cm)
max.
Countertop front
DR30ES, DR30EFS, DR30EIS, DR30EIFS
Revised 10/30/12 Page 3/4
Distinctive 30” Wide
Electric Ranges
Electrical Specifications
ELECTRICAL REQUIREMENTS
Electrical Circuit
Required
240 Vac 60 Hz, 4 wire*,
50 Amp.
*Two 120 Vac hot (L1 and L2), one neutral (N1) and one ground.
**This information above is for reference only. If the above data
does not agree with the product data label, use the data on the
product data label.
IMPORTANT: Freestanding ranges equipped for use in Canada
come pre-wired with a 4 wire appliance cord and NEMA 14-50P
plug. Do not modify the factory wiring. The plug is designed to
plug directly into a NEMA 14-50R electrical receptacle installed
by a licensed electrician according to the above specifications.
Total Connected
Load**
11.94kW (49.75 Amp.)
12” (30.5 cm)
2 1/2”
(6.4 cm)
10” (25.4 cm)
3 1/2”
(8.9 cm)
PLANNING
GUIDE
10” (25.4 cm)
1” (2.5 cm)
NEMA 14-50P PLUG NEMA 14-50R RECEPTACLE
Self-Rimming Installation Cutout Options (Models DR30EIS and DR30EIFS Only)
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.
Countertop thickness: 1 5/8” (4.1 cm) max.
UTILITY CLEARANCE BEHIND RANGE
TOP VIEW - SLIDE-IN, SELF-RIMMING INSTALLATION, 3”
All specications subject to change without notice.
SIDE PANELS INSTALLED
* To create a “built-in look” on the front of the cabinet, this dimension may be changed to
29 1/4” (74.3 cm), with the width at the notches remaining 30 1/16”. This configuration is
only for models DR30EIS and DR30EIFS with side panels behind door removed.
TOP VIEW - SLIDE-IN, SELF-RIMMING INSTALLATION, 3”
SIDE PANELS REMOVED
Phone: (800) 793-0093www.dacor.com
Page 4
Document # PG05-008
DR30ES, DR30EFS, DR30EIS, DR30EIFS
Revised 10/30/12 Page 4/4
Distinctive 30” Wide
Electric Ranges
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
■ Only models DR30EIS and DR30EIFS may be installed with a raised
vent. Use only Dacor raised vent model ERV3015.
■ A self-rimming countertop configuration is required for raised vent
installation. On installations with a raised vent, when sliding the range
into position, it will stop when the rear of the control panel or side
panels contact the notches toward the front of the countertop.
■ The self-rimming installation of the DR30DI range and ERV3015
raised vent create a “built-in” look where the range trim overlaps the
countertop on both sides and the raised vent overlaps the countertop
in back.
10” min. (25.4 cm)
to any combustibles
above counter both sides
24 3/8”
(61.9 cm)
max.
Countertop front
raised vent opening
countertop opening
to width of cabinets
Rear wall or
countertop edge
27 1/2” (69.9 cm)
29 1/4” (74.3 cm)
30 1/16” (76.2 cm)
cabinet opening
below countertop
Notch countertop
Cabinet face
below countertop
3/8” min. (1.0 cm)
countertop overhang
19 3/4”
19 3/4”
(50.2 cm)
(50.2 cm)
22 3/4”
(57.8 cm)
Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.
Countertop thickness: 1 5/8” (4.1 cm) max.
2 5/8” (6.7 cm)
to
3/8” min. (1.0 cm)
flat countertop
overhang
ERV3015
raised vent
PLANNING
25 9/16” (64.9 cm)
Range trim resting
on countertop
Countertop
3/8” min. (1.0 cm) space
required behind ERV3015
chassis to clear stiffener
DR30EI[F]S range
GUIDE
Cabinet face
Back of
side panel
rests against
cabinet face
3 inch
side panel
TOP VIEW - DOWNDRAFT ERV30[15] WITH SLIDE-IN, SELF-RIMMING INSTALLATION USING
10” min. (25.4 cm)
to any combustibles
above counter both sides
24 3/8”
(61.9 cm)
max.
Countertop front
TOP VIEW - DOWNDRAFT ERV30[15] WITH SLIDE-IN, SELF-RIMMING INSTALLATION USING
Rear wall or
countertop edge
27 1/2” (69.9 cm)
raised vent opening
29 1/4” (74.3 cm)
countertop opening
30 1/16” (76.2 cm)*
cabinet opening
below countertop
Notch countertop
to width of cabinets
Cabinet face
below countertop
3” SIDE PANELS INSTALLED
3/8” min. (1.0 cm)
countertop overhang
2 5/8” (6.7 cm)
22 3/4”
(57.8 cm)
3” SIDE PANELS REMOVED
3/8” min. (1.0 cm)
flat countertop
overhang
ERV3015
raised vent
25 9/16” (64.9 cm)
Range trim resting
on countertop
Countertop
Cabinet face
3/8” min. (1.0 cm) space
required behind ERV3015
chassis to clear stiffener
DR30EI[F]S range
* To create a “built-in look” on the front of the cabinet, this dimension may be changed to 29 1/4” (74.3 cm), with the width at the notches remaining 30
1/16”. This configuration is only for models DR30EIS and DR30EIFS with side panels behind door removed.
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
Loading...