Cyron RC3A12 Instructions Manual

RC3A12 RF REMOTE, TRI-ZONE

Thank you for choosing Cyron products! At Cyron we
are committed to provide the latest lighting technology
without any compromises. Please read instructions
completely before starting installation.

TOOLS NEEDED:

Wire stripper, Wire cutter, Electrical tape, Connector
Crimper may be used.

INSTRUCTIONS: Follow the wiring diagram below to
install the remote. It is best to make the 12VDC power
connection directly to the battery posts. Remove fuse
from fuse holder during the installation process. Make all
connections securely, following proper electrical
practices. Keep wires away from excess heat and
moving parts. Consult your vehicle owners manual if you
would like to connect to accessory switches. Do not
exceed max current capacity and power rating of vehicle
accessories.

Cyron RC3A12 is able to operate in basic mode (Uni­Zone) or advance mode (Tri-Zone). In the Uni-Zone
mode all the lights work together with a simple on/off
operation. In this mode buttons 2, 3, 4 of the remote are
deactivated.

In the Tri-Zone mode three zones (groups) of LEDs work almost independently. For example in a motorcycle lighting project Zone1 can
be the lights around the motor, Zone2 can be the ground effect lights, and Zone3 can be lights in the wheels. Each controller channel is
dedicated to a zone of lights. In fact, each zone can be any 12VDC LED that draws 3Amp or less.
IMPORTANT: Total controller capacity is 3x 3A or 9A. Do not exceed this rating. Serious damage to controller and wiring will be
caused.

OPERATIONS: Pair Up Remote: The first step is to pair up the remote to the controller. With all wiring completed remove the fuse
from fuse holder. Replace fuse back and within 5 seconds press button 1 three consecutive times. All channels should flash 5 times
confirming the pair up process. If not successful repeat process again.

Operation Modes: The controller presently is either Uni-Zone or Tri-Zone modes. Test by pressing
button 2 to see if any changes in lights take place. If pressing 2 does not change the lights the
remote is in Uni-Zone mode. If the lights do change the remote is in Tri-Zone mode.

Change from Uni-Zone to Tri-Zone:

1. Turn the lights off using Button 1.

2. Press and hold buttons 3 and 4 for one second.

3. Ch2 will flash 5 times to confirm.

Change from Tri-Zone to Uni-Zone:

1. Turn the lights off using Button 1.

2. Press and hold buttons 1 and 2 for one second.

3. Ch1 will flash 5 times to confirm.
A vast array of features are available in Tri-Zone mode. There are 10 light modes, 5 static and 5 dynamic. In Static modes the lights

are on solid without any movement. In Dynamic modes the lights (channels) go through a pre-programmed sequence of patterns which
are appropriately named in the chart below. Speeds of the patterns are adjustable by pressing button 3 to decrease and button 4 to
increase. There are 5 speeds in each Dynamic mode.

Brake light trigger/Aux Wire: This feature will make the accent light system become a safety or deterrent feature. Connecting Aux Wire
to +12VDC will turn on Channel 3 regardless if the controller is on or off. For instance, connect Aux wire to brake lights and every time
brakes are applied the lights of Ch3 can be additional visual signal. NOTE: Consult with your local laws regarding additional driving
lights on vehicles. Another usage can be connecting Aux wire to
output of an alarm system. Ch3 would turn on when alarm is
triggered.

Battery Saver: Controller will cut off the light system if the supply
voltage (vehicle battery) drops too low, preserving the battery for
starting the vehicle. With this feature the lights can be left on without
worrying about a dead battery. This feature does not apply to 24VDC
supply voltage.

Modes in Tri-Zone
(button 2 to change)

Channel
1

Channel
2

Channel
3

1 (Static)

ON

ON

ON

2 (Static)

ON

ON

OFF

3 (Static)

ON

OFF

OFF

4 (Static)

OFF

ON

ON

5 (Static)

OFF

OFF

ON

6 (Dynamic)

SHOW OFF

7 (Dynamic)

BRING IT ON

8 (Dynamic)

HEART BEAT

9 (Dynamic)

KNOCKOUT

10 (Dynamic)

BLIND SHOT

SPECIFICATIONS

Operating Voltage 12-24VDC, 3x3A (9A peak)
Control Processor PWM, Common Anode
Cutoff Voltage 11.35V
Standby Current 16mA
Transmitter Freq 433MHz

WARRANTY

Cyron warrants this product against any defects in materials or workmanship for a period of ONE (1) year from the date of purchase. The warranty covers normal usage as
intended by the factory and does not cover misuse, abuse, accidents, or damages caused due to the acts of God. Proof of purchase is required.
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS PROVIDED UNDER
THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OF
IMPLIED. IN NO EVENT SHALL CYRON, INC. BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS
OF REVENUE OR PROFITS, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE
THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitation on the length of an implied warranty, so the above
limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or from one
jurisdiction to another. Warranty inquiries can be emailed to [e-mail] or mailed to:
CYRON, Inc.
Warranty Claim Dept
21029-C Itasca Street
Chatsworth, CA 91311 USA

Other quality automotive lighting accessories & upgrades available from CYRON

For details please contact your local dealer or visit www.CYRON.com

Part Number Description/Application

CV62C-[color] Convex 6LED Cluster, Chrome finish PAIR
CV62-[color] Convex 6LED Cluster, Black finish PAIR
CV610C-[color] Convex 6LED Cluster, Chrome finish BULK PACK 10pcs
CV610-[color] Convex 6LED Cluster, Black finish BULK PACK 10pcs
FL30-[color] FlexLED super flexible strips, 30LED, 12”
CMF1202 Rigid mount for FlexLED, for ground effect & under bags
CON-TB005 Solder-less Terminal Block, 5 outlet
ABH4K-A6K Headlight LED bulb retrofit kit, H4
AB881-A6K Driving Lamp, LED 880, 881 fitting
RC3A12-REM Spare remote for RC3A12

System diagnostics:

LIGHTS DO NOT TURN ON

Diagnosis

Is the supply voltage connected properly?

Make proper connection to battery terminals

Is the fuse in the fuse holder? Is it the fuse blown?

Check the fuse. Fuse type 5A or 7.5A small blade

Has the remote been paired up with controller?

Take fuse out and plug back in. Within 5 seconds of plugging in press
button "1" on the remote 3 times. All channels should flash 5 times
indicating the remote and controller have been paired. With same
procedure up to two remotes can be learned by the controller. Pairing
up a 3rd remote will erase the first one.

REMOTE NOT FUNCTIONING

Diagnosis

Remote indicator light does not turn on

Check remote battery. Type 27A. Cyron Part# BAT-27A

Remote indicator light stays on

The buttons have been pressed too hard. The silicon rubber buttons
can be put out of alignment if pressed with too much force. Gently rock
the buttons as they are being pressed to set them back in place.