Cyron HTP2406W2 User Manual

21029-C ITASCA ST., CHATSWORTH, CALIFORNIA 91311 USA

www.cyron.com

HTP1506W2/2406W2

Multicolor LED Lighting System

Thank you for purchasing CYRON HTP1506W2/2406W2 LED Lighting
System. This system will bring the latest lighting technology to your home
theatre, home décor, cabinets, and many other areas you choose. Installation of
the system is simple and it can be done by anyone with little or no electrical
experience. Nonetheless, some custom installations may require professional
help. Please contact CYRON Technical Support at 888-297-6660 ext.106 for
advice.

Contents _____

Please locate all system components. If any of
the components are missing or damaged contact
CYRON before proceeding with installation.

1 x Controller
1 x Remote control
6 x Lightbars
1 x Power supply
12 x Mounting brackets
12 x Mounting tapes
Wipes/hardware

General Cautions _____

To reduce the risk of fire, electric shock, or injury:

Route and secure cords so that they will not be pinched or damaged
To further secure the wires, use only insulated staples or plastic ties
Not intended for recessed installations
Not intended for surface installation inside built-in furnishings
Do not install the entire system in closed compartments smaller than

4 cubic feet (26”x30”x10”)

To comply with National Electrical Code (NEC) and to prevent fire

danger, run the cords where they are accessible for examination.
Cords should be visually examined periodically and immediately
replaced when any damage is noted.

Installations _____

1. LIGHTBAR LOCATIONS NOTE: There are many intended uses and
methods of light placement. In most of the cases, the objective is to place the
lightbar so it is not directly visible, but only its projected lights are seen. Feel
free to experiment with light placement and direction of light projection. There
may be more than one good location.

Television Backlighting: The best location for television installations is
normally behind the TV, about 1 to 4 inches from the outer edges (left and right
in most cases). Vertically center the bars. You may use more than one light on
each side. See TV backlighting diagram. The exact location may vary
depending on the make and model of the TV.

Cabinets, Shelving, Furniture: Typical locations are top or bottom of the
cabinets, behind furniture trimmings, on the shelves, and behind glass covers.
Same general locations work well for most other objects. There are many ways
to backlight and accent light. Try various positions to achieve the desired
results.

General Wiring Diagram

with optional HTPR ribbon lights

2. CLEANING: Using the wipes provided test a small area to make sure it
does not affect the mounting surfaces. Clean the installation surfaces free of
dust/grease to assure the two-sided tape adheres well.

3. MOUNTING CLIPS: Mounting clips can be secured using the two-sided
tape or ½ inch screws. DO NOT USE SCREWS FOR FASTENING TO
ELECTRONIC DEVICES AND SENSITIVE SURFACES.
CAUTION: Tapes may cause discoloration to some surfaces over time.
Remove one side of the tape liner and apply to the bottom of the clips. Apply
pressure for 5 seconds to assure adhesion. Place clips on the lightbars.

4. LIGHTBAR PLACEMENT: Remove the second side of tape liner. Keep the
tape surface clean. Place the bars in the proper location by pressing on the clips
for 5 seconds. CAUTION: Never press on the clear lens of bars. Lightbars will
get damaged! Note the direction of the wires being routed to the hub.

5. CONTROLLER: It should preferably be installed out of sight, while
planning for the IR sensor (receiver) to be installed in line of sight. REMOTE
needs to be pointed at the IR sensor for operation. Cautions and Common
practices:

Keep the controller and wires away from extreme heat, liquids, and
moving objects.
Low voltage wires can be routed through walls and cabinets as long
as proper care is taken to avoid damages.

DO NOT modify internal components. Tampering with components
and wiring will void factory warranty.

6. POWER UP Plug the power supply into an AC outlet. The plug is polarized
(one blade is wider than the other) as a feature to reduce the risk of electric
shock. This plug will fit in a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit, contact the factory
or a qualified electrician. Never use with an extension cord unless the plug can
be fully inserted. Do not alter the plug.

7. DC JACK Connect the power supply DC cord to the controller DC input.

8. LIGHTBARS: Plug lightbars in the controller ports. The order is which the
lights get plugged in is not important.

Operations_____

Turn the unit on and adjust the light angle by twisting the light bars within the
brackets. Try several angles to achieve the desired results.

Operation of HTW202 controller is simple. Color buttons on the remote
correlate to the colors displayed. Four different color shows STROBE, STEP,
FADE, and COLOR automatically change light colors and patterns with pre­programmed sequences.

1. The speed of light can be changed using the Up and Down buttons. There
are 5 different speeds available in STROBE, STEP, FADE, and
COLOR modes. Brightness can also be adjusted in 5 steps. This
can only be done when displaying solid colors.

2. There are two buttons under R & G for enabling Soft Mode. First, ensure the
light is off. Press the Off button 5 times (the light should turn on). Next press
the orange button to turn on Soft Mode or the green button to turn off Soft
Mode. Simply turn off the light to save settings.

For Advanced Users Only!

3. Wiring sequences can be altered for products in which the lighting sequence

doesn’t match the remote, (the BRG sequence is selected by default.) First,

ensure the light is off. Next press the off button 5 times (the light should turn
on). Then press Yellow for RGB, Blue for GRB or Pink for BRG (buttons
available on last row). Lastly turn the light off to save.

Optional Settings

Turn LED System ON when an outlet is switched on: Plug the power supply to

a switched power source such as audio receiver’s “Switched Power” or wall

outlet that is controlled by a wall switch. Make sure the outlet is switched on.
Using the POWER button on the controller, make sure the LED System is off.
Press and hold the MODE button for 3 seconds. Now the unit will turn on
automatically every time the outlet is turned on.
LED System remains OFF when an outlet is switched on: In a similar process,
press and hold the PAUSE button for 3 seconds. The system will remain off

every time the outlet is switched on. In this mode, the system can only be
turned on from the controller by pressing the POWER button.

Possibilities _____

The controller is compatible with all Media Highlighter lights. System is
provided with 6 ports for easy connections to Media Highlighter Lightbars. For
the ultimate expandability, the system is equipped with a second output plug
that allows expanding the system with HTPR-RL ribbon lights or adding a
second hub for more Media Highlighter lights.

When expanding system, the power supply must be upgraded to

handle the total power usage of the system.

Specifications _____

Supply voltage range 100-240VAC, 50/60Hz

DC Supply voltage 12VDC
Peak power HTP1506W2=15W, HTP2406W2=27W
Nominal power HTP1506W2=7W, HTP2406W2=13W
Working Temperature -20 to 60ºC
Standby power 0.5W

HTW202 Controller Specifications _____

Supply voltage range 9-24VDC
Current 9A peak via DC jack
6A continuous
Continuous output power 72W @ 12VDC, 140W @ 24VDC
Working Temperature -20 to 60ºC
Common terminal Anode
Standby power 0.5W

Technical Support _____

CYRON’s primary goal is 100% customer satisfaction. You may call our technical

support line or contact us via email 24/7.
[e-mail]
818-772-1900 x106
In order to continually improve our products we welcome all comments about the product
you purchased.
Thank You!

Warranty _____

CYRON warrants this product against any defects in materials or workmanship for a period of ONE (1) year from the
date of purchase. The warranty covers normal usage as intended by the factory and does not cover misuse, abuse,
accidents, or damages caused due to the acts of God. Proof of purchase is required.

ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO
EVENT SHALL CYRON, INC. BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, ACCESSORY
OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR
LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR
IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE
FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.

Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or
limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights that vary from state to state or from one
jurisdiction to another.

Please mail all warranty claims to:
CYRON, Inc.
Warranty Claim Dept
21029-C Itasca Street
Chatsworth, CA 91311 USA

Further warranty inquiries: [e-mail]

Copyright © CYRON Lighting 2012