Cyron HTP1506E User Manual [en, es]
21029 ITASCA ST., UNIT C, CHATSWORTH, CALIFORNIA 91311 USA
www.CYRON.com
Multicolor LED Lighting System
Media Highlighter
HTP1506E / HTP2406E
1
Español
page 6
21029 ITASCA ST., UNIT C, CHATSWORTH, CALIFORNIA 91311 USA
www.cyron.com
Multicolor LED Lighting
Media Highlighter
HTP1506E / HTP2406E
Thank you for purchasing CYRON Multicolor LED Lighting System. This system
will bring the latest lighting technology to your home theatre, home décor, cabinets,
and many other areas you choose. Installation of the system is simple and it can be
done by anyone with little or no electrical experience. Nonetheless, some custom
installations may require professional help. Please contact CYRON Technical Support
at 818-772-1900 ext.106 for advice.
General Cautions
To reduce the risk of fire, electric shock, or injury:
Route and secure cords so that they will not be pinched or damaged
To further secure the wires, use only insulated staples or plastic ties
Not intended for recessed installations
Not intended for surface installation inside built-in furnishings
Do not install the entire system in closed compartments smaller than 4 cubic
feet (26”x30”x10”)
To comply with National Electrical Code (NEC) and to prevent fire danger, run
the cords where they are accessible for examination. Cords should be visually
examined periodically and immediately replaced when any damage is noted.
Contents
Please locate all system components. If any of the
components are missing or damaged contact CYRON
before proceeding with installation.
1 x Controller / Hub
6 x Lightbars
1 x Power supply
4 x Mounting brackets
Tapes, Hardware, Wipes
2
Installations
1. LIGHTBAR LOCATIONS NOTE: Depending on
the application, as few as one or as many as six
lightbars may be used. There are many intended uses
and methods of light placement. In most of the cases,
the objective is to place the lightbar so it is not
directly visible, and its projected light is only seen.
This is particularly important if combined colors
such as white are being produced. Feel free to
experiment with light placement and direction of
light projection. There may be more than one good
location.
Television Backlighting: The best location for
television installations is normally behind the TV,
about 1 to 4 inches from the outer edges (left and
right in most cases). Also, vertically center the bars.
See TV backlighting diagram. The exact location may vary depending on the make
and model of the TV.
Cabinets, Shelving, Furniture: Typical locations are: Top or bottom of the cabinets,
behind furniture trimmings, on the shelves, and behind glass covers. Same general
locations work well for most objects. There are many ways to backlight and accent
light. Try various positions to achieve the desired results.
2.
3
CLEANING a Using the wipes provided test a small area to make sure it does
not affect the mounting surfaces. Clean the installation surfaces free of dust/grease to
assure the two-sided tape adheres well.
3. MOUNTING CLIPS Mounting clips can be secured using the two-sided tape or
screws. DO NOT USE SCREWS FOR FASTENING TO ELECTRONIC DEVICES
AND SENSITIVE SURFACES.
CAUTION: Tapes may cause discoloration to some surfaces over time. Remove one
side of the tape liner and apply to the bottom of the clips. Apply pressure for 5 seconds
to assure adhesion. Place clips on the lightbars.
4. LIGHTBAR PLACEMENT Remove the second side of tape liner. Keep the tape
surface clean. Place the bars in the proper location by pressing on the clips for 5
seconds. CAUTION: Never press on the clear lens of bars. Lightbars will get
damaged! Note the direction
of the wires being routed to
the hub.
5. HUB Mount the hub using
screws or tapes. Plug the
lightbar connectors into hub
outlets. The plugs are
polarized and can only be
plugged in one direction.
6. CONTROLLER Use tape
to mount the controller in an
accessible location. Some
painted surfaces may get
damaged upon future removal
of the tape/controller.
7. POWER UP Plug the power supply into an AC outlet. The plug is polarized (one
blade is wider than the other) as a feature to reduce the risk of electric shock. This
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact the factory or a qualified
electrician. Never use with an extension cord unless the plug can be fully inserted.
Do not alter the plug.
8. DC JACK Connect the DC power jack into the controller DC cord.
Operations
Turn the unit on and adjust the light angle by twisting the lightbars within the
brackets. Try several angles to achieve the desired results.
4
Loading...