Page 1
Cybex FT-325
Owners Manual and Service Manual
Strength Systems
Part Number 18000-999-4 A
www.cybexintl.com
Page 2
Table of Contents
Safety
Safety .................................... 3
Safety Guidelines And Practices ............... 5
Regular Maintenance Activities ................ 7
Warnings and Cautions ...................... 8
Label Placement............................ 9
Assembly
Machine Specications...................... 10
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Assembly Procedure ....................... 10
Exercise
Intended Use ............................. 16
Instructions ............................... 16
Maintenance
Daily Procedures .......................... 19
Weekly Procedures ........................ 22
Yearly Procedures ......................... 24
Cable Adjustment .......................... 25
Belt Adjustment............................ 26
Environment and Storage.................... 26
Customer Service
Product Registration........................ 27
Contacting Service ......................... 27
Ordering Parts ............................ 27
Return Material Authorization (RMA) ........... 28
Damaged Parts............................ 29
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.
DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the
contents of this manual. We reserve the right to revise this document at any time or to make
changes to the product described within it without notice or obligation to notify any person of such
revisions or changes.
© Copyright 2011, Cybex International, Inc. All rights reserved. Printed in the United States of
America.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexintl.com • techhelp@cybexintl.com • 18000-999-4 A
Page 3
Cybex FT-325 Owner’s Manual
Safety
Safety
Cybex international partners with equipment owners to establish the safest and most effective setup
of Cybex equipment. Cybex International urges each facility owner to carefully follow all safety
precautions. Following theses precautions are the best protection against personal injury or damage
to equipment or facility.
The most important safety precaution is to maximize stability for every piece of equipment. The
equipment should be securely anchored to the oor. It is imperative the oor be level.
Read the Owner’s Manual carefully before assembling, servicing, or using the equipment. In an
institutional environment, it is the facility owner’s responsibility to properly instruct users on the proper
operation of the equipment and to warn them of the potential hazards.
Follow and enforce the User Safety Precautions to protect both the user and the equipment. Keep
children away from selectorized strength equipment. Children must be supervised.
Do not allow anyone, including trainers, to use equipment in a manner other than shown on the
instruction placards located on every machine.
It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper
operation of the equipment and review all labels.
WARNING: Serious injury or death could occur if these safety precautions are not
followed:
User Safety Precautions
• Read all warnings posted on the machine. Warnings are posted on each machine to alert the
user to potential problems. Following warning labels will prevent injury or equipment damage.
• Read and understand warning labels and user manual prior to exercising. Obtain
instruction prior to use. Each machine has instructions posted on the equipment for proper
use.
Use the selectorized and plate loaded machines as shown on placards.• DO NOT modify the
machine.
Never pin the weights in an elevated position. • DO NOT use the machine if found in this
condition. See assistance from oor staff. Weights pinned up have the potential to fall if the user
pulls the pin. Floor staff should lower the weights to prevent potential problems.
Be certain that the weight pin is completely inserted (for selectorized strength equipment that •
employ weight stacks). If the pin is not completely inserted the user may accidentally drop the
weights if the pin falls out.
3
Page 4
Cybex FT-325 Owner’s Manual
Inspect the machine for worn or loose components prior to use. Tighten/replace any loose or worn •
components before to using. Pay close attention to belts, cables, grips or pulleys and their
connections. Always look for potential problems in equipment condition. Loose components should
be tightened to function properly. Replacing worn components maintains the equipment is in the
best condition for regular use.
Never use dumbbells or other means to incrementally increase the weight resistance. Use only •
those means provided by the manufacturer for the equipment. Altering the machine design by
adding additional weight as with dumbbells or other means can injure the user, may damage the
equipment, and will void the warranty.
Set up, anchor, and operate selectorized strength equipment on a solid level surface. • If the oor is
not level the equipment is not stable.
• DO NOT wear loose or dangling clothing or jewelry while using selectorized strength
equipment. Stay clear of all moving components. Loose clothing or dangling jewelry can
become entangled in moving parts, potentially cause severe injury or damage, or ruin the clothing
or jewelry.
Consult a physician prior to commencing an exercise program. If at any time during exercise you •
feel faint, dizzy or experience pain, stop and consult your physician. Users must be
responsible and cautious with the condition of their own health. Consulting a physician before
beginning a program can alert the user to the personal risk if health is an issue.
Use a spotter for Free Weight equipment. • A spotter adds an additional level of safety.
• DO NOT exceed the maximum specied user weight. Too much weight on a machine may
prevent it from proper function. Too much weight on a machine may damage the
machine.
• DO NOT use if equipment appears damaged or inoperable upon inspection. If the machine
appears damaged or inoperable- contact the oor staff.
DO NOT• attempt to x a broken or jammed machine. Notify oor staff. It is the owner’s
responsibility to repair broken or jammed equipment.
• DO NOT use if guards are missing or damaged. Replace all missing or damaged parts to
ensure function and safety. Guards prevent things from interfering with function.
• DO NOT remove any labeling from equipment. Replace any damaged labels. Labels give users
specic information and alerts. Replacing damaged labels ensures users can read the labels for
information provided.
Facility Safety Precautions
• Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
It is the sole responsibility of the user/owner or facility operator to ensure that regular •
maintenance is performed.
To maximize stability, securely anchor each machine to the oor using the anchor holes •
provided in each machine. Each machine must be set up, anchored, and operated on a solid level
surface.
4
Page 5
Cybex FT-325 Owner’s Manual
Do not install equipment on an uneven surface!
DANGER !
Death or serious injury will occur if the
following requirements are not met:
Ensure that all users are properly trained on how to use the equipment.•
Verify there is enough room for safe access and operation of the equipment. Spacing •
requirements for each piece of equipment can be found in the Assembly section of this manual, on
the assembly instructions during setup, and on the cybexintl.com website.
Perform regular maintenance checks on the equipment as detailed in the Maintenance section of •
this manual. Inspect all areas most susceptible to wear, including, (but not limited to) cables,
pulleys, belts, and grips.
Immediately replace worn or damaged components. If unable to immediately replace worn or •
damaged components then remove from service until the repair is made.
Cybex is not able to anchor the equipment due to local building codes.
The owner is responsible for the actual anchoring of equipment.
Consult with a professional contractor.
Use fasteners having a minimum of 500 lbs. tensile capacity -- Cybex
recommends 3/8” grade 2 bolts or better.
If legs/frame does not contact surface, DO NOT pull down with
anchors. Shim any leg or frame not in contact with surface using at
washers.
Use only Cybex supplied components to maintain/repair the equipment.•
Keep a repair log of all maintenance activities.•
Display the Facility Safety Sign so it is visible and prominent.•
Safety Guidelines And Practices
Cybex recommends that all tness equipment be used in a supervised area. It is recommended that
the equipment be located in an access controlled area. Control is the responsibility of the owner. The
extent of control is at the discretion of the owner.
It is the responsibility of the purchaser/user of Cybex products to read and understand the owner’s
manual, and warning labels; as well as instruct all individuals, whether end users or supervising
personnel, on proper usage of the equipment.
5
Page 6
Cybex FT-325 Owner’s Manual
SECURING EQUIPMENT
Do not use machine until it is properly anchored.
The machine has holes in the feet, which allow for ease in anchoring to the oor. All anchoring holes
must be used to maximize stability. Cybex strongly recommends equipment be secured to a solid,
level surface to eliminate rocking, tipping, or falling over due to incorrect usage and misuse.
The solid, level surface should not deviate more than 1/8” over a 10’ distance or as dened and
required by local building and architectural codes.
Anchoring of equipment must be completed by a qualied licensed contractor.
Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when
anchoring the equipment to the oor.
Due to the wide variation of ooring on which machines may be anchored or installed, verify
anchoring method and anchoring fasteners with a qualied and licensed contractor.
A minimum pull out force of 220 lbs/100 kgs is required for each anchor position.
PROPER USAGE
Use machine only as described in the manual. Failing to follow proper instructions may result in injury.
WARNING: Serious injury or death could occur if the following warnings are not
enforced: DO NOT Lean Against or Pull On the framework, weight stack,
or any component, whether machine is at rest or in use. Inappropriate or
improper use may result in injury to users or third parties (bystanders)
STANDARD COMPLIANCE
Cybex products meets applicable ASTM and EN Standards.
6
Page 7
Cybex FT-325 Owner’s Manual
Regular Maintenance Activities
Preventative maintenance activities must be performed to maintain normal and safe operation of your
equipment. Keeping a log sheet of all maintenance actions will assist you in staying current with all
preventative maintenance activities. The preventative maintenance actions are described in detail in
the maintenance section of this manual. Briey, they include:
Daily
Clean upholstery.•
Weekly
Inspect all nuts and bolts for looseness. Tighten as required.•
Inspect all cables and belts for damage or wear. If a cable or belt is worn or damaged, •
immediately discontinue use until cable or belt has been replaced.
Check for worn handles, worn snap links, and worn warning labeling. Replace all worn parts •
immediately.
Inspect for loose or worn grips. Replace all loose or worn grips immediately.•
Inspect weight stacks for proper alignment and operation. Correct all improper alignment and •
operation issues immediately.
Lubricate guide rods using automotive engine oil only.•
Yearly
Replace all cables and belts at least annually.
7
Page 8
Cybex FT-325 Owner’s Manual
MATERIAL:
EXCEPT AS NOTED
GENERAL
TOLERANCES:
REMOVE ALL BURRS
BREAK SHARP EDGES
.005/.010 R
SURFACE FINISH
DIMENSIONS
IN INCHES
WARNING
SERIOUS INJURY
COULD OCCUR IF
THESE PRECAUTIONS
ARE NOT OBSERVED
2. Read and understand warning labels
and user manual prior to exercising.
Obtain instruction prior to use.
1. Obtain a medical exam prior to
beginning an exercise program.
3. Keep body and clothing free from
and clear of all moving parts.
4. Inspect machine prior to use. DO
NOT use if it appears damaged or
inoperable.
5. DO NOT attempt to fix a broken or
jammed machine. Notify floor staff.
6. Use the machine only for the
intended use. DO NOT modify the
machine.
7. Be sure that the weight pin is
completely inserted. Use only the pin
2.25
12 PT ARIAL FONT
R .25
4 PLACES
INSET .06
WHITE
SAFETY ORANGE PMS 152
BLACK TRIANGLE W/ ORANGE
EXCLAMATION POINT, BLACK LETTERS
23 PT ARIAL BOLD FONT
8.00
8.25 PT ARIAL FONT
WHITE BACKGROUND
BLACK LETTERS
Warnings and Cautions
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death
or serious injury.
Caution decals indicate a potentially hazardous situation, which, if not avoided, could result in minor
or moderate injury.
The warning and caution decals are shown on the following page. The diagrams following the decals
show where each decal is located.
A
B
8
Page 9
Label Placement
Cybex FT-325 Owner’s Manual
B
B
B
A
A
Description Part No.
Warning Decal...................4605-381-XA.
Caution Decal....................8500-025-XB.
9
Page 10
Cybex FT-325 Owner’s Manual
Assembly
Machine Specifications
Total Weight and Size:
752 lbs. inches - 58.88 W x 37.20 L x 83.42 H
55 kg cm - 149.55 cm W x 94.49 cm L x 211.89 cm H
Tools Required
9/16” Wrench•
7/32” Allen wrench•
3/4” Socket•
Hammer•
3/16” Pin punch•
Loctite• ® #242®
Two people will be required for this procedure. It is the responsibility of the facility owner/owner of the
equipment to ensure that there is appropriate clearance around each machine to allow for safe use
and passage.
Assembly Procedure
Read and understand all instructions thoroughly before assembling this unit.
Verify parts list shown below.
Qty Part Number Description Diagram
4
1
16010-311
4800-557
Foot pad
Decal (10-150)
1
4800-433
Rope Handle
10
Page 11
Cybex FT-325 Owner’s Manual
Qty Part Number Description Diagram
1 12220-005 Handle Assembly
1 51122 Ankle strap
Placement
If Then
Two people will be required for this procedure
FT-325cantthrough
doorway
Move to desired location.1.
If Then
FT-325cannott
through doorway
Remove the four shipping cones using a 3/4” wrench.2.
Attach foot pads to each foot of frame. 3.
Two people will be required for this procedure
Remove the four shipping cones using a 3/4” wrench.1.
Attach foot pads to each foot of frame2.
Remove back panels from machine. 3.
Verify weight stack pin is disengaged. 4.
11
Page 12
If Then
FT-325cannott
through doorway
Cybex FT-325 Owner’s Manual
Remove spiral pin connecting pulley using a hammer and a 3/16” 5.
pin punch
Spiral
pin
Move pulley and cable connection out of the way. 6.
Remove guide rod caps. Guide rod cap contains a compression 7.
spring that will y if grasp is not released slowly. Slide spring loaded
guide rod cap down guide rod until cap is clear of frame. Slowly
release grasp of guide rod cap and remove.
Remove lifting post.8.
Remove weight plates.9.
Remove plastic insert plug, located at top of machine. 10.
Plastic
Insert
plug
12
Page 13
If Then
FT-325cannott
through doorway
Cybex FT-325 Owner’s Manual
Loosen the two button head socket cap screws (BHSCS) securing 11.
chin up bar to frame using a 7/32” Allen wrench.
BHSCS
Hold thread block in place with ngers and remove the BHSCS. 12.
Thread block
13
Page 14
If Then
FT-325cannott
through doorway
Cybex FT-325 Owner’s Manual
Remove BHSCS and locknuts, remove one side of connector tubes 13.
using a 7/32” Allen wrench and a 9/16 wrench.
Tube
connector
Move machine to desired position.14.
Reattach frame halves and securely tighten the BHSCS.15.
Place two drops of Loctite 242 to each BHSCS and threaded hole 16.
for Chin up bar. Securely tighten BHSCS.
Insert plastic plugs. 17.
Securelyanchormachinetotheoor
Cybex strongly recommends to maximize stability, equipment must be secured to a solid level
surface.
CAUTION: Cybex is not responsible for the actual anchoring of equipment. Consult with
a professional contractor..
WARNING: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8’’ grade 2
bolts or better).
WARNING: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim
any leg or frame not in contact with surface using at washers.
14
Page 15
Cybex FT-325 Owner’s Manual
Install individual weight plates one at at time
Position each weight plate so wide edges of bushings face upward and narrow edges 1.
of bushings face downward.
CORRECT
Wide bushing
edge faces upward
Install lifting post.2.
Cable routing
Position pulley mount parallel to the top weight. 1.
Pull down on pulley mount until cable is tight.2.
Verify cable is still routed through all pulleys.3.
Attach pulley mount to lifting post using a hammer and spiral pin. 4.
WRONG
The narrow bushing edge
must face downward.
Spiral
Lift top weight up and down simulating normal operation (without selecting any resistance).5.
Verify the cable is moving smoothly.6.
Install back panels
Verify proper operation
pin
15
Page 16
Cybex FT-325 Owner’s Manual
Exercise
Intended Use
The intended use of this machine is to aid or improve general physical tness and exercise for
commercial use.
Instructions
Read an understand all instructions and warnings prior to using this machine in the Safety
section of the Owner’s Manual.
Select appropriate resistance.1.
Adjust handles for proper pulley height.2.
Ensure all adjustment knobs are locked into place.3.
CHEST PRESS OVERHEAD PRESS
Motions Developed
Shoulder Flexion, Elbow Extension
Muscles Used
Pectoralis Major
Motions Developed
Shoulder Abduction, Elbow Extension
Muscles Used
Anterior Deltoid, Middle Deltoid
16
Page 17
Cybex FT-325 Owner’s Manual
ROW LAT PULL
Motions Developed
Shoulder Extension, Elbow Flexion
Muscles Used
Lattisimus Dorsi, Teres Major,
Trapezius, Rhomboid, Rear Deltoid
TORSO ROTATION ARM CURL
Motions Developed
Shoulder Adduction, Elbow Flexion
Muscles Used
Lattisimus Dorsi, Teres Major,
Trapezius, Rhomboid
Motions Developed
Spine Rotation
Muscles Used
External Obliques
Motions Developed
Elbow Flexion
Muscles Used
Biceps Brachii, Brachialis,
Brachioradialis
17
Page 18
Cybex FT-325 Owner’s Manual
ARM EXTENSION SQUAT
Motions Developed
Elbow Extension
Muscles Used
Triceps
HIP ABDUCTION HIP ADDUCTION
Motions Developed
Knee Extension
Muscles Used
Quadriceps, Gluteus Maximus,
Hamstrings, Thoracolumbar Fascia
Motions Developed
Hip Abduction
Muscles Used
Piriformis, Tensor Fasciae Latae
Motions Developed
Hip Adduction
Muscles Used
Adductor Magnus, Adductor Longus,
Adductor Brevis, Pectineus
18
Page 19
Cybex FT-325 Owner’s Manual
NOTE: All inspections
and repairs must be
performed by trained
service personnel only.
Use only Cybex replacement
parts when servicing.
Failure to do so could result
in personal injury.
CAUTION
Maintenance
All preventive maintenance activities must be performed on a regular basis. Performing routine
preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex Strength
Systems equipment.
Cybex is not responsible for performing regular inspection and maintenance actions for your
machines. Instruct all personnel in equipment inspection and maintenance actions and also in
accident reporting/recording. Cybex phone representatives are available to answer any questions that
you may have.
All inspections and repairs must be performed by trained service personnel only. Cybex will
void warranty in non-Cybex replacement parts are used.
Daily Procedures
When using strong cleaning agents such as rubbing alcohol or bleach, it is advisable to rst test in an
inconspicuous area. Other cleaning agents may contain harsh or unknown solvents and are subject to
formula changes by the product manufacturer without notice. Should you desire to use other cleaning
agents, carefully try them in an inconspicuous area to determine potential damage to the material.
Never use harsh solvents or cleaners which are intended for industrial applications. To clean stained
or soiled areas, a soft white cloth is recommended. Avoid use of paper towels.
Cleaning products may be harmful/irritating to your skin, eyes, etc. Use protective gloves and eye
protection. Do Not inhale or swallow any cleaning product. Protect surrounding area/clothing from
exposure. Use in well ventilated area. Follow all product manufacturer’s warnings. CYBEX and
its vendors cannot be held responsible for damage or injuries resulting from the use or misuse of
cleaning products.
19
Page 20
Clean Upholstery
Cybex FT-325 Owner’s Manual
If Then
Prepare a solution of 10% household 1.
liquid soap and warm water.
Apply with a soft damp cloth. 2.
Light Soiling
MoreDifcultStains
If necessary, apply a solution of liquid 3.
cleanser with a soft bristle brush.
Dampen a clean soft cloth in water and 4.
wipe residue away.
Prepare a solution of 10% household 1.
bleach (sodium hypochlorite) and 90%
water. Dampen a soft white cloth in the
solution.
Rub gently on the stained area.2.
Dampen a clean soft cloth in water and 3.
rinse area.
If stains are still present, a full strength 4.
household bleach may be used. Allow
bleach to puddle on the affected area or
apply with a bleached-soaked cloth for
approximately 30 minutes. Dampen a
clean soft cloth in water, and rinse area to
remove any remaining bleach
concentration.
Dampen a soft white cloth with rubbing 1.
alcohol.
MoreDifcultStains(AlternativeMethod)
Gently rub stained area.2.
Dampen a clean soft cloth in water and 3.
rinse area.
Apply a light coat of furniture wax for 30 1.
Restoring Luster
seconds.
Lightly rub area using a clean white cloth.2.
Clean Frames
Wipe down all frames using a mild solution of warm water and car wash soap. Be sure to dry
thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these
could scratch or damage the equipment.
20
Page 21
Cybex FT-325 Owner’s Manual
Clean Chrome
Clean chrome tubes, rst using chrome polish and then using a car wax seal. Neutral cleaners with a
pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or chlorine based
cleaners and also cleaners containing abrasives as these could scratch or damage the equipment.
Guidelines for cleaning front panel:
Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing. Follow
up each application with warm water rinse.
DO NOT• use abrasives or high alkaline cleaners.
DO NOT• leave cleaners on for long periods, wash immediately.
DO NOT• apply cleaners in direct sunlight or at elevated temperatures.
DO NOT• use scrapers, squeegees, or razors.
DO NOT• clean with gasoline.
Compatible Cleaners and Detergents:
Formula 409•
Top Job•
Joy•
Palmolive•
Windex with Ammonia D•
To Minimize Fine or Hairline Scratches:
Mild automotive polish applied and removed with a soft clean cloth will help ll scratches.
Suggested Polishes:
Johnson Paste Wax•
Mirror Glaze #10 Plastic Polish (by Mirror Bright Polish Co.)•
Novus Plastics Polish #1, #2 (By Novus Inc.)•
21
Page 22
Cybex FT-325 Owner’s Manual
Weekly Procedures
Inspect All Nuts and Bolts
Tighten all loose nuts and bolts as required.
WARNING: Serious injury or death may result if the following precautions are not
followed. Replace all worn cables and belts.
Inspect cables and belts
Inspect all cables and belts for wear or damage and proper tension. When inspecting cables and
belts, run ngers on the cable or belt, paying particular attention to bends in and attachment points.
The following conditions may indicate a worn cable:
Condition of Cable Diagram
A tear or crack in the cable sheath
that exposes the cable
A kink in the cable
A curled sheath
Necking - A stretched cable sheath
Belts
Condition of Belt 3D View 3D or Side View
Peeling of the belt’s skin.
Wave in belt
22
Page 23
Cybex FT-325 Owner’s Manual
Condition of Belt 3D View 3D or Side View
Belt is necked down (narrow section)
Cracks or splits
One or more strands of kevlar is
hanging out, or if there is a signicant
amount of frayed kevlar.
Replace belt if any
section is over 1/32”
(.03) narrower than the
rest of belt
Examine edge of belt (both sides).
Replace belt if any section is
narrower than the rest.
23
Page 24
Cybex FT-325 Owner’s Manual
CAUTION: Personal injury or property damage may occur if the following conditions
exist. Replace all worn handles immediately. Do not use if less than 1/8” of
material remains to the edge.
Inspect bars and handles for wear, paying particular attention to tab area connection points.
Replace bar if less
than 1/8” of material
remains to the edge.
Attachment
Hole
Inspection Action
Inspect bars and handles for wear, paying
particular attention to tab area connection points.
Inspect snap links for proper latching (indicates
wear).
Inspect all labeling for readability, including
instructional placards, warning and caution
decals.
Inspect all weight stacks for proper alignment
and operation.
Inspect guide rods for lubrication.
Yearly Procedures
Replace all cables and belts annually
Replace all worn handles immediately.
Replace all loose or worn grips immediately.
Replace all worn labeling immediately.
Correct all improper alignment and operation
issues immediately.
Wipe Weight Stack Guide Rods clean over entire
length. Lubricate with a light coat of medium
weight automotive engine oil.
24
Page 25
Cybex FT-325 Owner’s Manual
Cable Adjustment
Tools Required
9/16” Wrench (2)
Four types of cable tension adjustment are used on Cybex Strength Systems:
Cable
Adjustment
Jam Nut
Adjustment
Rod End
Adjustment
Description Diagram
This type of adjustment uses a jam
nut and a tension adjustment nut at
the cable cam end as the primary
adjustment. The other end of the
cable usually contains a roll pin
adjustment.
This type of adjustment uses a
socket head cap screw (SHCS)
securing a cable rod end bearing to
the machine. Primary adjustment
is by turning the rod end bearing.
The other end of the cable usually
contains a roll pin cable adjustment.
Jam
Cable
End
SHCS
Nut
Tension
Adjustment
Nut
Jam Nut
Cable Rod End
Bearing
Nylon
Locknut
Roll Pin
Adjustment
Cam End
Adjustment
This type of adjustment uses a roll
pin and series of holes in the weight
stack top weight connector.
This type of adjustment uses an
adjustment bolt on the pulley
bracket. Loosen nut and rotate cam
bolt to adjust cable.
25
Roll
Pin
Nut
Top Weight
Connector
Cam Bolt
Adjustment
Page 26
Cybex FT-325 Owner’s Manual
Belt Adjustment
Tools Required
7/32” Wrench•
Torque wrench (in/lbs) •
Belt Adjustment Action
Loose Belt Using a 7/32” Allen wrench loose set screws. 3.
Pull belt tight. 4.
Secure belt in place with set screws.5.
Torque set screws to 300-350 in/lbs.6.
Verify that the belt is moving smoothly and is routed straight from 7.
the top pulley bracket to the to weight belt clamp
Environment and Storage
Static Electricity
To reduce static electricity increase the humidity.
Humidity
The unit is designed to function normally in an environment with a relative humidity range of 30% to
75%. The unit can be shipped and stored in an environment with a relative humidity range of
10% to 90%.
Temperature
The unit is designed to function normally in an environment with an ambient temperature range of
50° F (10° C) to 104° F (40° C). The unit can be shipped and stored in an environment with a relative
humidity range of 10% to 90%.
Do not install, use, or store the unit in an area of high humidity, such as near a steam room, sauna,
indoor pool or outdoors. Extensive exposure to water vapor, chlorine and/or bromine could adversely
affect the equipment.
26
Page 27
Cybex FT-325 Owner’s Manual
Customer Service
Product Registration
To register product do the following:
Visit 1. www.cybexintl.com.
Locate Product Registration in the Support section.2.
Fill out form completely.3.
Click the Submit button to register product.4.
Contacting Service
Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard
Time.
For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or
fax 508-533-5183.
Find information on the web at www.cybexintl.com or e-mail at techhelp@cybexintl.com.
Ordering Parts
To order parts online go to www.cybexintl.com. Select Support > Parts / Ordering. In the left
navigation panel, click Parts Diagrams - Current Products. Select from the drop down boxes.
To speak with a customer service representative, call 888-462-9239 (for customers living within the
USA) or 508-533-4300 (for customers outside the USA). You may also contact us through e-mail at
techhelp@cybexintl.com.
27
Page 28
Cybex FT-325 Owner’s Manual
This product may be produced under
one or more of the following patents
5,628,715 5,643,152 5,616,107
5,722,921 5,620,402 6,488,612
6,743,158 7,179,209 7,335,139
7,338,415 7,503,882 D480,773
D481,428 D486,535 D490,127
D490,128 D490,865 D491,237
D491,238 D497,190 6,033,350
7,727,128 7,717,831
1975 24th Ave SW Owatonna,MN. 55060 1-888-462-9239
Made in U.S.A.
MODEL# 8810-90
SERIAL# XXXXXXXXXXXXX
The following information located on the serial number decal will assist our Cybex representatives in
serving you.
Unit Serial Number, Product Name and Model Number•
Part Description and Part Number if you have it. All parts can be found on the web at •
www.cybexintl.com
Shipping Address•
Contact Name•
In addition to your shipping address and contact name, your account number is helpful but not
required. You may also fax orders to 508-533-5183.
Return Material Authorization (RMA)
The Return Material Authorization (RMA) system is used when returning material for placement,
repair or credit. The system assures that returned materials are properly handled and analyzed.
Follow the following procedures carefully.
Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will
request a RMA from Cybex, if applicable. Under no circumstances will defective parts or equipment
be accepted by Cybex without proper RMA and an Automated Return Service (ARS) label.
Call the Customer Service Hot Line listed above for the return of any item that is defective.
Provide the technician with a detailed description of the problem you are having or the defect in the
item you wish to return. Provide the model and serial number of your Cybex equipment.
At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for
evaluation and repair or replacement. The technician will assign you a RMA number and will send
you an ARS label. The ARS label and the RMA numbers must be clearly displayed on the outside
of the package that contains the item(s) to be returned. Include the description of the problem, the
serial number of the equipment and the name and address of the owner in the package along with the
part(s).
28
Page 29
Cybex FT-325 Owner’s Manual
Forward the package through UPS to Cybex.
Attn: Customer Service Department
Cybex International, Inc.
1975 24th Ave SW
Owatonna, MN 55060
Merchandise returned without an RMA number on the outside of the package or shipments sent COD
will not be accepted by the Cybex receiving department.
Damaged Parts
Materials damaged in shipment should not be returned for credit. Shipping damages are the
responsibility of the carrier (UPS, Federal Express, trucking companies, etc.)
Apparent Damage
Upon receipt of your shipment, check all items carefully. Any damage seen with a visual check must
be noted on the freight bill and signed by the carrier’s agent. Failure to do so will result in the carriers
refusal to honor your damage claim. The carrier will provide you with the required forms for ling such
claims.
Concealed Damage
Damage not seen with a visual check upon receipt of a shipment but notices later must be reported
to the carrier as soon as possible. Upon discovery of the damage, a written or phone request to
the carrier asking them to perform an inspection of the materials must be made within ten days of
the delivery date. Keep all shipping containers and packing materials as they will be needed in the
inspection process. The carrier will provide you with an inspection report and the necessary forms for
ling a concealed damage claim. Concealed damage claim is the carrier’s responsibility.
29
Page 30
Page 31
Page 32
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexintl.com • techhelp@cybexintl.com
Loading...