Cybex 750T Treadmill
Product Number 751T
Owner’s Manual
Cardiovascular Systems
Part Number LT-20406-4 J
www.cybexinternational.com
Cybex 750T Treadmill
Product Number 751T
Owner’s Manual
Cardiovascular Systems
Part Number LT-20406-4 J
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. Safety Sentry™ is a registered trademark of Cybex
International, Inc. Polar® is a registered trademark of Polar Electro Inc.
DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual. We reserve the
right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any
person of such revisions or changes.
© 2010, Cybex International, Inc. All rights reserved. Printed in United States of America.
10 Trotter Drive Medway, MA 02053 • 888-462-9239 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • techhelp@cybexintl.com • LT-20406-4 J • September 2010
Cybex 750T Treadmill Owner’s Manual
Table of Contents
Front Pages
About this Manual . . . . . . . . . . . . . . . . . . iii
FCC Compliance Information . . . . . . . . . . iii
1 Safety
Important Voltage Information . . . . . . . 1-1
Grounding Instructions . . . . . . . . . . . . . 1-1
Important Safety Instructions . . . . . . . . 1-2
Warning Decals . . . . . . . . . . . . . . . . . . 1-4
Caution Decals . . . . . . . . . . . . . . . . . . . 1-6
Emergency Stop Key (e-stop) . . . . . . . 1-6
CSAFE Ports. . . . . . . . . . . . . . . . . . . . . 1-7
2 Assembly and Setup
Warnings/Cautions . . . . . . . . . . . . . . . . 2-1
Choosing and Preparing a Site . . . . . . 2-1
Electrical Power Requirements . . . . . . 2-2
Assembling the Treadmill . . . . . . . . . . . 2-2
Testing the Treadmill Operation . . . . . 2-10
Seup . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
3 Operation
Terms and Symbols Used . . . . . . . . . . 3-1
Quick Operation Guide. . . . . . . . . . . . . 3-2
Detailed Operation Guide . . . . . . . . . . . 3-2
Stopping the Treadmill . . . . . . . . . . . . . 3-5
Immobilization Method . . . . . . . . . . 3-5
Emergency Dismount . . . . . . . . . . . 3-5
Emergency Stop . . . . . . . . . . . . . . . 3-5
Safety Sentry™. . . . . . . . . . . . . . . . . . . 3-5
Control During Operation . . . . . . . . . . . 3-6
Data Readouts . . . . . . . . . . . . . . . . . . . 3-6
Displaying Heart Rate. . . . . . . . . . . . . . 3-7
Heart Rate Zone . . . . . . . . . . . . . . . . . . 3-8
Meaning of % Grade . . . . . . . . . . . . . . 3-8
Preprogrammed Workouts . . . . . . . . . . 3-9
Custom Programs . . . . . . . . . . . . . . . . 3-9
Alarm . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Audio Visual (AV) Key Pad – Optional 3-11
Statistics . . . . . . . . . . . . . . . . . . . . . . . 3-12
4 Preventive Maintenance
Warnings/Cautions . . . . . . . . . . . . . . . . 4-1
Regular Maintenance Activities . . . . . . 4-1
Cleaning Your Treadmill . . . . . . . . . . . . 4-1
Running Belt Maintenance . . . . . . . . . . 4-3
Other Preventive Maintenance . . . . . . . 4-5
Service Schedule . . . . . . . . . . . . . . . . . 4-6
5 Customer Service
Contacting Service . . . . . . . . . . . . . . . . 5-1
Serial Number and Voltage . . . . . . . . . 5-1
Return Material Authorization (RMA) . . 5-2
Damaged Parts. . . . . . . . . . . . . . . . . . . 5-2
Ordering Parts . . . . . . . . . . . . . . . . . . . 5-3
Appendix A - Technical Specifications . . A-1
Page i
Cybex 750T Treadmill Owner’s Manual
Page ii
Cybex 750T Treadmill Owner’s Manual
About This Manual
An Owner’s Manual is shipped with each unit. To purchase additional copies of this manual or any other
Cybex manual, please do one of the following:
• fax your order to 508-533-5183
• contact Cybex Customer Service at 888-462-9239
• or contact Cybex Customer Service at 508-533-4300
To contact Cybex with comments about this manual you may send email to techhelp@cybexintl.com.
FCC Compliance Information
WARNING: Changes or modifi cations to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception (which
can be determined by turning the equipment off and on) the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver is •
connected.
Consult the dealer or an experienced radio TV technician for help.•
Page iii
Cybex 750T Treadmill Owner’s Manual
Page iv
Cybex 750T Treadmill Owner’s Manual
1 - Safety
IMPORTANT: Read all instructions and warnings before using the treadmill.
Important Voltage Information
Before plugging the power cord into an electrical outlet, verify that the voltage requirements for the site
match the voltage of the treadmill that has been received. The power requirements for the Cybex 750T
Treadmill include a grounded, dedicated circuit, rated for one of the following:
100 VAC, 50/60 Hz, 20A•
115 VAC, 60 Hz, 20A•
220 VAC, 60 Hz, 15A•
230 VAC, 50 Hz, 15A•
230 VAC, 50 Hz, 13A, UK•
See the serial number decal for the exact voltage requirements of the treadmill.
WARNING: Do not attempt to use this unit with a voltage adapter. Do not attempt to use this unit
with an extension cord.
WARNING: Do not plug more than one unit into a single circuit.
Grounding Instructions
This treadmill must be grounded. If it should malfunction or break down, grounding provides a path of
least resistance for electric current to reduce the risk of electric shock. This product is equipped with a
cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
DANGER: Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualifi ed electrician or service provider if there is doubt as
to whether the treadmill is properly grounded. Seek a qualifi ed electrician to perform
any modifi cations to the cord or plug. Cybex is not responsible for injuries or damages
as a result of cord or plug modifi cation.
This treadmill is for use on a
grounded, dedicated circuit. Make
sure that the treadmill is connected
to an outlet having the same
confi guration as the plug. Do not
use a ground plug adapter to adapt
the power cord to a non-grounded
outlet.
115 VAC Euro Plug 220 VAC UK Danish
NEMA 5-20 CEE 7/7 NEMA 6-15 230 VAC IEC320
Safety
Page 1-1
Cybex 750T Treadmill Owner’s Manual
Important Safety Instructions
(Save These Instructions)
DANGER: To reduce the risk of electric shock, always unplug this treadmill from the electrical
outlet immediately after using it and before cleaning it.
WARNING: Serious injury could occur if these precautions are not observed. To reduce the risk
of burns, fi res, electric shock, or injury:
User Safety Precautions
Obtain a medical exam before beginning any exercise program. •
WARNING: Heart rate monitoring systems may be inaccurate. Over exercise may result in serious
injury or death. If you feel faint stop exercising immediately.
Stop exercising if you feel faint, dizzy, or experience pain and consult your physician. •
Obtain instruction before using.•
Read and understand the Owner’s Manual and all warnings posted on the unit before using. •
Read and understand emergency stop procedures.•
DO NOT • wear loose or dangling clothing while using the treadmill.
Keep all body parts, towels, water bottles and the like free and clear of moving parts. •
Place your feet on the two top steps when starting or stopping the treadmill. •
Use the treadmill handrails for support and to maintain balance.•
Keep children away from the treadmill. Teenagers and disabled persons must be supervised while •
using.
DO NOT • use the unit if you exceed 400 lbs. (181 kg). This is the rated maximum user weight.
Report any malfunctions, damage or repairs to the facility.•
Replace any warning labels if damaged, worn or illegible.•
Stop and place the treadmill at 0 degrees incline (level) after each use.•
Disconnect power before servicing.•
Facility Safety Precautions
Instruct all users on how to clip the e-stop clip onto their clothing and carefully test it prior to using the •
treadmill.
Instruct all users to use caution when mounting and dismounting the treadmill.•
Use a dedicated line when operating the treadmill. • NOTE: A dedicated line requires one circuit breaker
per unit.
Connect the treadmill to a properly grounded outlet only.•
DO NOT• operate electrically powered treadmills in damp or wet locations.
Safety
Page 1-2
Cybex 750T Treadmill Owner’s Manual
Keep the running belt clean and dry at all times.•
DO NOT • leave the treadmill unattended when plugged in and running. NOTE: Before leaving the
treadmill unattended, always wait until the treadmill comes to a complete stop and is level. Then, turn
all controls to the STOP or OFF position and remove the plug from the outlet. Remove the e-stop key
from the treadmill.
Immobilize the treadmill (when not in use) by removing the e-stop key.•
Inspect the treadmill for worn or loose components before each use. Do not use until worn or damaged •
parts are replaced.
Maintain and replace worn parts regularly. Refer to “Preventive Maintenance” section of Owner’s •
Manual.
DO NOT• operate the treadmill if: (1) the cord is damaged; (2) the treadmill is not working properly or
(3) if the treadmill has been dropped or damaged. Seek service from a qualifi ed technician.
DO NOT • place the cord near heated surfaces or sharp edges.
DO NOT • use the treadmill outdoors.
DO NOT • operate the treadmill around or where aerosol (spray) or where oxygen products are being
used.
Read and understand the Owner’s Manual completely before using the treadmill.•
Ensure all users wear proper footwear on or around all Cybex equipment.•
Set up and operate the treadmill on a solid, level surface. Do not operate in recessed areas or on •
plush carpet.
Provide the following clearances: 19.7 inches (0.5 m) at each side, 79 inches (2.0 m) at the back and •
enough room for safe access and passage at the front of the treadmill. Be sure your treadmill is clear
of walls, equipment and other hard surfaces.
DO NOT• attempt repairs, electrical or mechanical. Seek qualifi ed repair personnel when servicing. If
you live in the USA, contact Cybex Customer Service at 888-462-9239. If you live outside the USA,
contact Cybex Customer Service at 508-533-4300.
Use Cybex factory parts when replacing parts on the treadmill.•
DO NOT • modify the treadmill in any way.
DO NOT • use attachments unless recommended for the treadmill by Cybex.
Ensure all User and Facility Safety Precautions are observed.•
Safety
Page 1-3
Cybex 750T Treadmill Owner’s Manual
Carefully read and understand the following before using the 750T treadmill:•
Warning Decals•
Caution Decals•
To replace any worn or damaged decals do one of the following: Visit www.cybexinternational.com
to shop for parts online, fax orders to 508-533-5183 or contact Cybex Customer Service at 888-462-9239.
If you are located outside of the USA, call 508-533-4300. For location or part number of labels, see the
parts list and exploded-view diagram. This information can be found in the Service chapter in this manual
or on the Cybex web site at www.cybexinternational.com.
Warning Decals
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or
serious injury. The warning decals used on the Cybex 750T are shown below.
DE-20735-4
Warning
Safety
Page 1-4
Cybex 750T Treadmill Owner’s Manual
DE-20427
Warning Motor
Cover
Safety
Page 1-5
Cybex 750T Treadmill Owner’s Manual
Caution Decals
Caution decals indicate a potentially hazardous situation, which if not avoided, may result in minor or
moderate injury. There are no caution decals used on this unit. However, there are caution statements
listed in Chapters 2 and 5 of this manual. See Chapters 2 and 5.
Emergency Stop Key (e-stop)
The e-stop key functions as an emergency stop. In an emergency situation, the e-stop key disengages
from the console and the treadmill will come to a stop. Before using the treadmill, clip the e-stop key as
described below.
1. Compress the spring and clip the e-stop clamp to your clothing.
Ensure the clip engages enough clothing so it does not fall off in an
emergency situation. See Figure 1. NOTE: Be sure the string is free
of knots and has enough slack for you to workout comfortably with the
e-stop key in place.
2. Without falling off the treadmill, carefully step backward until the
e-stop pulls out of the console. See Figure 2. NOTE: If the e-stop clip
falls off your clothing then the test has failed. Reclip the e-stop clip to
your clothing and repeat this step.
3. Replace the e-stop key. See Figure 2.
4. The treadmill is now ready to be used. NOTE: Ensure the the e-stop
clip is secured to your clothing at all times during use.
Clothing
Clip
Figure 1
Figure 2
5. After use, remove the e-stop key from the treadmill.
NOTE: The e-stop key can be removed to help prevent unauthorized use. Refer to the Stopping the
Treadmill section in the Operation chapter for more information about the e-stop key.
Safety
Page 1-6
Cybex 750T Treadmill Owner’s Manual
NOTE: When not in use store the e-stop clip on the storage tab located on the lower cover. See Figure 3.
Lower
Cover
Storage
Tab
Figure 3
E-Stop
Clip
CSAFE Ports
The 750T Treadmill has two CSAFE ports, one in the console for CSAFE devices that need access
there, and one under the base of the unit for running a network connection.
NOTE: The CSAFE standard defines a communication protocol and low-voltage DC power source
specific to the Fitness Equipment Industry. These RJ-45 phone jacks are provided for use ONLY
within the CSAFE protocol. For more information on the CSAFE standard, visit
www.fitlinxx.com/csafe. Not every connection carries both the communication and power
capability.
NOTE: The console CSAFE port inside the console contains the full implementation, with both network
communications and a standard CSAFE voltage (minimum 8.0 VDC) power source. The base
CSAFE port is accessible under the base of the treadmill and is for network communications
only and does not contain the DC power source. See Figures 4 and 5.
CSAFE Port
(Lower Socket)
Figure 4
Console CSAFE Port Location
Safety
Page 1-7
Base CSAFE Port Location
CSAFE
Port
Bottom View
Cybex 750T Treadmill Owner’s Manual
Figure 5
Safety
Page 1-8
Cybex 750T Treadmill Owner’s Manual
2 - Assembly and Setup
Warnings/Cautions
All warnings and cautions listed in this chapter are as follows:
WARNING: Use extreme caution when assembling the treadmill. Failure to do so could result in
injury.
WARNING: During this procedure STAY OFF THE RUNNING BELT! Stand with your feet on the two
steps.
CAUTION: A minimum of two people are required to lift, move and assemble this treadmill.
Always use proper lifting methods when moving heavy items.
Choosing and Preparing a Site
Before assembling the treadmill a suitable site must selected and have the proper electrical outlet power
available for optimum operation and safety. See the Electrical Power Requirements section (located on
the next page) for direction in locating the treadmill’s voltage requirements.
The area selected for the treadmill should be well lit and well ventilated. Locate the treadmill on a
structurally sound and level surface (do not place in recessed areas or on plush carpet) a few feet away
from walls and other equipment. Each side of the treadmill should have a 19.7” (0.5 m) minimum space.
Behind the treadmill should be 79” (2.0 m) minimum of space. Allow enough clearance for safe access
and passage during use of the machine. If the treadmill is to be located above the fi rst fl oor, place it near
or above major support beams. If the area has a heavy, plush carpet, the airfl ow around the base of the
machine may be restricted or the carpeting may interfere with the moving parts. To protect the carpeting
and the machinery, place a 3/4” (1.9 cm) thick wood base under the treadmill.
Do not install the treadmill in an area of high humidity, such as in the vicinity of a steam room, sauna,
indoor pool, or outdoors. Exposure to extensive water vapor, chlorine, and/or bromine could adversely
affect the electronics as well as other parts of the machine.
Assembly
and
Setup
Page 2-1
Cybex 750T Treadmill Owner’s Manual
Electrical Power Requirements
The power requirements for this treadmill are a grounded, dedicated circuit rated for one of the following:
100 VAC, 50/60 Hz, 20A•
115 VAC, 60 Hz, 20A•
220 VAC, 60 Hz, 15A•
230 VAC, 50 Hz, 15A•
230 VAC, 50 Hz, 13A, UK•
Contact a qualifi ed electrician to ensure the power supply complies with local building codes.
Do not use a ground plug adapter to adapt the 3-prong power cord plug to a non-grounded electrical
outlet. Do not use an extension cord.
Assembling the Treadmill
WARNING: Use extreme caution when assembling the treadmill. Failure to do so could result in
injury.
CAUTION: A minimum of two people are required to assemble this treadmill.
Tools Required
1/2” Socket wrench with a 4” extension•
1/2” Box end wrench, 12 point•
9/16” Socket wrench with a 4” extension•
Phillips screwdriver•
NOTE: The words “left” and “right” denote the treadmill user’s orientation.
1. Read and understand all instructions thoroughly before assembling the treadmill.
NOTE: Each step number in the assembly instructions tells you what you will be doing. The lettered
steps following each step number describe the procedure required. Do not continue with step 2
until you have carefully read all of the assembly instructions.
2. Verify you have received the correct package.
Read the sticker on the outside of the box and verify that the model number, color and voltage are A.
what you ordered. NOTE: During step 3 and 5 you will verify that the contents of the box match
the sticker.
3. Unpack and verify the contents of the boxes.
Lift up and remove the cardboard sleeve that surrounds the treadmill. A.
Verify the following items are present. Check off ( B. ) each item as you fi nd it. See Figure 1. If any
of the parts are missing contact Cybex Customer Service.
Assembly
and
Setup
Page 2-2
Loading...