Cybex 360A User Manual

Cybex Arc Trainer 360A

Owner’s Manual

Model Number: 360A

USER WEIGHT LIMITATION: 300lbs (135 kg)

SERIAL NUMBER (found on frame):

P/N LT-20894-4 Rev B

PS-MU-R360A-01

www.cybexinternational.com 2

For future service or related questions:

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your Home Arc
Trainer.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Precautions:

WARNING: Failure to Read and Follow the following Precautions could result in Serious Injury! To reduce the risk of
burns, fire, electric shock, or injury to persons, read the following important precautions and information before operating
the Home Arc Trainer. It is the responsibility of the owner to ensure that all users of this Home Arc Trainer are adequately
informed of all warnings and precautions.

SAFETY PRECAUTIONS

• Use the Home Arc Trainer only as described in this manual.

• Place on a level surface, with 6 feet (2 m) of clearance behind it. Do not place the Home Arc Trainer on any surface that

blocks air openings. To protect the floor or carpet from damage, place a mat under the Home Arc Trainer.

• When choosing a location for the Home Arc Trainer make sure that the location and position permit access to a plug.

• Keep the Home Arc Trainer indoors, away from moisture and dust. Do not put the Home Arc Trainer in a garage or

covered patio, or near water.

• Do not operate the Home Arc Trainer where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the Home Arc Trainer at all times.

• The Home Arc Trainer should not be used by persons weighing more than 300 lbs (135 kgs)

• Never allow more than one person on the Home Arc Trainer at a time. Wear appropriate exercise clothing when using the

Home Arc Trainer. Do not wear loose clothing that could become caught in the Home Arc Trainer. Athletic support clothes
are recommended for both men and women. Always wear athletic shoes. Never use the Home Arc Trainer with bare feet,
wearing only stockings, or in sandals.

• When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same
circuit.

• Obtain a medical exam before beginning any exercise program.

• Stop exercising if you feel faint, dizzy or experience pain.

• Always examine your Home Arc Trainer before using to ensure all parts are in working order.

• Allow the foot plates to fully stop before dismounting.

• Never insert any object or body parts into any opening.

• Follow the safety information in regards to plugging in your Home Arc Trainer.

• Keep the power cord away from the incline wheels and do not run the power cord underneath your Home Arc Trainer. Do

not operate the Home Arc Trainer with a damaged or frayed power cord.

• Always unplug the Home Arc Trainer before cleaning and/or servicing. Service to your Home Arc Trainer should only be
performed by an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to
follow these instructions will void the Home Arc Trainer warranty.

• Never leave the Home Arc Trainer unattended while it is running.

• The equipment is for Home Use Only. Use of the Home Arc Trainer in a commercial, hotel, or other setting than an

individual home will void all warranties and could cause injury.

www.cybexinternational.com 3

W

arning decal part number PS-DC-D350A-08

Carefully read and understand the following before using the unit:
Note: to replace any worn or damaged decals do one of the following : visit

www.cybexinternational.com to shop for parts online, fax your order to 508-533-5183 or contact Cybex

Customer Service at 800-766-3211. if you live outside of the USA, call 508-533-4300.

Warning decals indicate a potentially hazardous situation, which, which, if not avoided, could result in death or
Serious injury. The warning decals are shown below.

Warning Decals

www.cybexinternational.com 4

Warning Decals

Warning decal part number
FS-DC-D350-07

www.cybexinternational.com 5

Warning Decals

Warning decal part number
PS-DC-D350A-11

www.cybexinternational.com 6

Caution decals indicate a potentially hazardous situation, which, if not avoided, may result in minor or
Moderate injury. The caution decals are shown below.

Caution Decals

Caution decal part number
PS-DC-D350A-06

www.cybexinternational.com 7

Continental Europe

North America

Australia

/

New Zealand

United Kingdom

/

Ireland

Power Requirements:

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A RISK OF AN ELECTRIC
SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE PROVIDER IF YOU ARE IN DOUBT AS TO WHETHER THE
UNIT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT. IF THE PLUG WILL NOT
FIT THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

The Home Arc Trainer can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes,
surges and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the
possibility of damage, always use a surge protector (not included) with your unit.

This Home Arc Trainer must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for
electric current, should the Home Arc Trainer malfunction. This unit comes with an electrical cord having an equipment-grounding
conductor and a grounding plug.

POWER REQUIREMENTS

This Home Arc Trainer is for use on a nominal 115 VAC +/- 5%, 50/60 Hz and 15 amps; or 230
VAC +/- 10%, 50/60 Hz and 10 amps.

Product Spec:

Product dimensions : L70.7 x W28.5 x H62.3 INCH
Product weight: 300 LBS (135KGS).
Power required : 110VAC or 220VAC

NOTE: Before plugging the power cord into an electrical outlet, verify that
the voltage requirements for your area match the voltage of the unit that
you received.

CEE 7 / 7
16A / 230V / 50Hz

AS/NZS 3122
10A / 230V / 50Hz

BS 1363
13A / 230V / 50Hz

NEMA5-15
15A / 120V / 60Hz

www.cybexinternational.com 8

Open the boxes:

As you open each box, take inventory of all items contained inside the box. Use the “Content Checklist” and “Hardware Comparison
Chart” located on the following pages to assist you in taking inventory of each box. If you are missing any parts or have any
assembly questions call your local Cybex Retailer or Cybex Customer Service 1-888-462-9239.

Gather your tools:

Before starting the assembly, gather all the necessary tools you need to assemble the unit properly.

Clear your work area:

Make sure that your work area is free and clear from all objects that may cause injury during assembly. After the unit is fully
assembled, allow enough clearance for safe access and operation.

Invite a friend:

For assembly steps that require heavy lifting, use a minimum of two people to lift, move and assemble this unit.

User Weight Limitation:

Do not use this unit if you weigh more than 300 lbs (135 kg). This is the rated maximum user weight. Serious injury may

occur if the user’s weight exceeds 300 lbs (135 kg).

Care and maintenance:

1. The safety level of the Home Arc Trainer can be maintained only if it is examined regularly for damage and wear.

2. Replace defective components immediately and stop the use of the equipment until it is repaired.

3. Always be careful when mounting or dismounting the equipment. Use the handles to steady yourself before starting your

4. Always check your Home Arc Trainer for any worn parts or torn or damaged labels. If any parts are broken or labels missing,

Cleaning Your Home Arc Trainer:

After each use:

As Needed:

PREASSEMBLY

workout. Dismount from the equipment only after you have come to a complete stop.

please call Cybex Customer Service.

1. Wipe up any liquid spills immediately.

2. Use a cloth to wipe up any remaining perspiration from the handles and painted surfaces.

1. Clean your unit using a spray a mild cleaning agent, such as a water and dish soap solution, on a clean cloth first and then
wipe the unit with a damp cloth. NOTE: Do not spray cleaning solution directly on the unit. Direct spraying could cause
damage to the electronics and may void the warranty.

2. Vacuum any dust or dirt that might accumulate under or around the unit.

www.cybexinternational.com 9

Carton contents:

For your convenience, we have identified the contents of the shipping carton. Please check to make sure you have all of the
components before assembly. This chart is provided to help you identify the components used in the assembly of this product.

No. Description Qty.

Box A

Box B 1

CONTENTS CHECKLIST

Computer set 1

513

Adjustable foot stand M8

321

Handlebar bottom bushing

351

Handlebar front end-upper

352

Handlebar front end-bottom

353

Water bottle cover-outer left

354

Water bottle cover-inner left

355

Water bottle cover-outer right

356

Water bottle cover-inner right

362

Water bottler insert

360

Console mount cover-front

361

Console mount cover-back

521

Power cord

625 Chest belt 1

A

Hardware kit

Box C 1

358

Foot pedal cover-left

359

Foot pedal cover-right

363

Pedal soft cushion

2

2

1

513

321

351

A BOX

352

1

1

1

353

354

355

356

1

1

2

2

521

625

362

360

361

2

1

A

1

B BOX

1

1

358

359

2

363

C BOX

www.cybexinternational.com 10

Hardware chart:

For your convenience, we have identified the hardware used in the assembly of this product. This chart is provided to help you
identify those items that may be unfamiliar to you.

No. Description Qty.

501

502 Button head cap screw M6x16

HARDWARE COMPARISON CHART

Flat hex head bolt M8x16

4

2

514

503

504

505

506

507

508

509

510

511

512

514

515

516

517

Button head hex bolt M6x12

Allen Head Cap Bolt M8x25

M8X25 Bolt

M10x70 Bolt

Crank bushing 35X35 mm

M4x19 Screw

M10 Nylon Nut

φ16 x 6 x T2 washer

φ32 x 8 x T2.0 washer

Φ18 x12XT3.5 washer

Φ18x 10XT2.0 washer

Self tapping screw M4X12

φ16x8xT2 Curve Washer

M8 Spring washer

A Phillips Head Wrench

B M5 Allen wrench

C M4 Allen wrench

D 17mm Spanner

E 19mm Spanner

2

2

2

8

4

2

2

4

2

2

8

4

4

4

1

1

1

1

1

501

505

510

D

502

506

511

512

503

507

515

BA

E

504

508

516 517

C

F

509

F 6mm Allen Wrench

1

MILLIMETERS

www.cybexinternational.com 11

PARTS LIST

Description Qty.

Order No.

101

Main frame

Front linkage-left

105

Front linkage-right

106

Moving Linkage-left

109

Moving Linkage -right

110

116

Console support bracket

A01 Fly wheel set

A02

Left handlebar set

A03

Right handlebar set

Back linkage-left

A04

Back linkage-right

A05

A06

Rear support leg

A07

Arm linkage

Foot support tube assembly-right

A08

Foot support tube assembly-left

A09

Water bottle cover-left

A10

Water bottle cover-right

A11

Power switch set

A12

1

1

1

1

1

1

1

1

1

1

1

2

2

1

1

1 360A-A10

1 360A-A11

1 360A-A12

360A-101

360A-105

360A-106

360A-109

360A-110

360A-116

360A-A01

360A-A02

360A-A03

360A-A04

360A-A05

360A-A06

360A-A07

360A-A08

360A-A09

A13 Console insert 1 360A-A13

202

Bearing 6804

205

Bearing 2205

206

Bearing 6001

208

Bearing 6205

209

Bearing BL-6206

Tolerance ring AN28-(ID28xT8)

210

Tolerance ring AN32-(ID32xT7)

211

Tolerance ring AN52-(ID52xT18)

214

Front linkage bushing 35x14.7--ID15

216

Drive linkage bushing 45x22.36—ID25.05

217

221

Moving wheel

Drive linkage axel 45x56.1-(25x34.5)-M8

223

Front linkage axel 35x39.2-(15x24.5)-M6

224

Oval tube cap

225

Plastic cover insert

230

Console cover-upper

302

4 360A-202

4 360A-205

4 360A-206

2 360A-208

2 360A-209

4 360A-210

4 360A-211

4 360A-214

2 360A-216

2 360A-217

2 360A-221

2 360A-223

2 360A-224

2 360A-225

12 360A-230

1 360A-302

www.cybexinternational.com 12

303

304

305

306

307

309

310

311

313

314

316

317

318

320

321

323

351

352

357

358

359

360
363

402

407

409

411

422

423

427

432

433

434

435

437

441

447

448

451

452

454

455

463

468

PARTS LIST

Description Qty. Order No.

Console cover-bottom

Console tray-upper

Console tray-bottom

Main cover-left

Main cover-right

Incline motor cover-left

Incline motor cover-right

Pulley cover

Rear support leg bottom cover-inner

Rear support leg bottom cover-outer

Back linkage end cap

Drive linkage rear axel cover

Front linkage axel cover

Back linkage bushing ring

Handlebar bottom bushing

Moving wheel cover
Handlebar front end-upper

Handlebar front end-bottom

Foot pedal cover-upper

Foot pedal cover-left

Foot pedal cover-right

Console mount cover-front

Pedal soft cushion

Flat hex head bolt M8x16

Button head cap screw M5x10

Button head cap screw M6x16

Button head cap screw M10x50
Button head M5x35

Button head M5x45

Nylon nut M10
Arm linkage axel

Back linkage axel

Foot support axel

Phillips head M4x15

Phillips head M4x15

R clip
Washer 30x8xT2.0

Washer 24x8xT2.0

Washer 20x6xT3.0

Bushing 12x8x6

Phillips head M4x25

Sleeve

Bearing Spacer

Washer 30x8xT3.0

1 360A-303

1 360A-304

1 360A-305

1 360A-306

1 360A-307

1 360A-309

1 360A-310

2 360A-311

2 360A-313

2 360A-314

2 360A-316

2 360A-317

2 360A-318

2 360A-320

2 360A-321

2 360A-323

1 360A-351

1 360A-352

2 360A-357

1 360A-358

1 360A-359

2 360A-360
2

8 360A-402

4 360A-407

6 360A-409

2 360A-411

4 360A-422

2 360A-423

2 360A-427

2 360A-432

2 360A-433

2 360A-434

20 360A-435

20 360A-437

4 360A-441

4 360A-447

2 360A-448

2 360A-451

2 360A-452

1 360A-454

2 360A-455

2 360A-463

2 360A-468

360A-363

501

502

503

504

505

506

507

508

509

510

511

512

513

514

515

516

517

521

610

615

621

A02 Left handlebar set

103

321

207

213

501

510

A03

104

321

207

213

501

510

A04 Back linkage-left

107

312

PARTS LIST

Description Qty. Order No.

Flat hex head bolt M8x16

Button head cap screw M6x16

M8X25 Bolt

Bolt M12x70

Crank bushing 35x35

Allen head screw M6x12

Allen head screw M4x19

Nylon nut M10

Washer 16x6xT2

Washer 30x8xT2.0

Washer 18x12xT3.5

Washer 18x10xT3.0

Adjustable foot stand M8

Allen head screw M4x12

16x8xT2 Curve Washer

M8 Spring washer

Allen Head Cap Bolt M8x25

Phillips Hand Wrench

A

M5 Allen wrench

B

M4 Allen wrench

C

17mm Spanner

D

19mm Spanner

E

Power code
12Pin power wire-upper

4P hand pulse signal wire-upper

Heart rate grommet

Left handlebar frame

Handlebar bottom bushing ring

Bearing 6005

Tolerance ring AN47-(ID47xT12)

Flat hex head bolt M8x16

Washer 30x8xT2.0

Right handlebar set

Right handlebar frame

Handlebar bottom bushing ring

Bearing 6005

Tolerance ring AN47-(ID47xT12)

Flat hex head bolt M8x16

Washer 30x8xT2.0

Back linkage-left

Foot support tube axel cover

www.cybexinternational.com 13

4 360A-501

2 360A-502

2

2 360A-504

2 360A-505

8 360A-506

4 360A-507

2 360A-508

2 360A-509

4 360A-510

2 360A-511

2 360A-512

2 360A-513

8 360A-514

4 360A-515

4 360A-516

4

1 360A-A

1 360A-B

1 360A-C

1 360A-D

1 360A-E

1 360A-521

1 360A-610

1 360A-615

2 360A-621

1

1 360A-321

2 360A-207

2 360A-213

1 360A-501

1 360A-510

1

1 360A-321

2 360A-207

2 360A-213

1 360A-501

1 360A-510

1 360A-107

1

360A-503

360A-517

360A-103

360A-104

360A-312

A05 Back linkage-right

108

312

A06 Rear support leg

111

324

A07 Arm linkage

113

206

210

361

439

502

509

A08 Foot support tube assembly-right

114

203

207

212

213

315

319

402

435

440

447

A09 Foot support tube assembly-left

115

203

207

212

213

315

319

402

435

440

447

PARTS LIST

Description Qty. Order No.

Back linkage-right

Foot support tube axel cover

Rear support leg
Rear support leg stand

Arm linkage

Bearing 6001

Tolerance ring AN28-(ID28xT8)

Console mount cover-back

R clip

Button head cap screw M6x16

Washer 20x6xT1.5

Foot support tube assembly-right

Bearing 2202

Bearing 6005

Tolerance ring AN35-(ID35xT14)

Tolerance ring AN47-(ID47xT12)

Front linkage top axel cover

Front linkage bushing ring

Flat hex head bolt M8x16

Phillips head M4x15

R clip

Washer 30x8xT2.0

Foot support tube assembly-left

Bearing 2202

Bearing 6005

Tolerance ring AN35-(ID35xT14)

Tolerance ring AN47-(ID47xT12)

Front linkage top axel cover

Front linkage bushing ring

Flat hex head bolt M8x16

Phillips head M4x15

R clip

Washer 30x8xT2.0

www.cybexinternational.com 14

1

1

1

1 360A-324

1 360A-113

1 360A-206

1 360A-210

1 360A-361

1 360A-439

1 360A-502

1 360A-509

1 360A-114

1 360A-203

2 360A-207

1 360A-212

2 360A-213

1 360A-315

1 360A-319

1 360A-402

1 360A-435

1 360A-440

1 360A-447

1 360A-115

1 360A-203

2 360A-207

1 360A-212

2 360A-213

1 360A-315

1 360A-319

1 360A-402

1 360A-435

1 360A-440

1 360A-447

360A-108

360A-312

360A-111

www.cybexinternational.com 15

A10

353

354

230

506

507

362

A11

355

356

230

506

507

362

A12

233

308

408

421

424

601

602

603

A13 Console insert

301

436

608

609

A14 Bearing Support Tube 2

PARTS LIST

Description Qty. Order No.

Water bottle cover-left

Water bottle cover-outer left

Water bottle cover-inner left

Plastic cover insert

Allen head screw M4x15

Allen head screw M4x19
Water bottler insert

Water bottle cover-right

Water bottle cover-outer right

Water bottle cover-inner right

Plastic cover insert

Allen head screw M4x15

Allen head screw M4x19
Water bottler insert

Power switch set

Power switch bracket

Power input set

Button head cap screw M5x25

Button head M3x6

Nut M5

Power insert set

Fuse

Power switch

Console insert with PC board

Phillips head M3x12
Computer overlay-upper

Computer overlay-bottom

1 360A-353

1 360A-354

3 360A-230

4 360A-506

1 360A-507

1 360A-362

1 360A-355

1 360A-356

3 360A-230

4 360A-506

1 360A-507

1 360A-362

1 360A-233

1 360A-308

2 360A-408

2 360A-421

2 360A-424

1 360A-601

1 360A-602

1 360A-603

1 360A-301

8 360A-436

1 360A-608

1 360A-609

360A-A14

www.cybexinternational.com 16

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

501

452

360

510

441

205

214

516

515

A06

517

214

205

441

510

360

452

501

798,32

A06

517

516

515

A07

435

313

314

435

313

A02

314

A07

435

A03

www.cybexinternational.com 17

402

447

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

PARTS DIAGRAM

447

433

455

209

402

A11

357

A10

402

208

422

223

317

110

217

A05

447

363

214

205

441

320

359

432

437

468

402

506

A08

202

106

224

225

323

411

101

512

512

206

511

504

210

211

211

463

216

508

A14

448

210

402

202

423

318

621

409

451

513

427

221

206

318

423

210

A14

202

105

216

451

323

225

411

206

504

511

210

432

211

463

211

621

224

358

109

437

402

506

A09

357

402

447

209

455

433

363

320

441

205

214

217

468

422

317

208

A06

223

www.cybexinternational.com 18

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

PARTS DIAGRAM

407

230

437

311

435

435

435

307

A12

309

A01

230

437

310

306

454

437

407

311

435

437

www.cybexinternational.com 19

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

409

116

303

A13

230

302

437

304

305

437

507

503

352

230

610

351

615

www.cybexinternational.com 20

ASSEMBLY

STEP 1:

Open box, remove the three (3) accessories boxes positioned between the foot pedals and set aside. Remove arms
and set aside. Remove the zip tie which tightens the frame on the wooden rack and remove the wooden rack.
Determine location of use for the 360A Home Arc Trainer and lift main frame (101) out. Note: It is recommended
that two people lift the main frame out of the box. Remove all other packing material from the frame. Lift the back
end up as shown.

101

www.cybexinternational.com 21

517

516

STEP 2:

With back end elevated, insert Left Rear Support Leg (A06) and Right Rear Support Leg (A06) into the frame and
secure with M8x25 Allen Head Cap Bolt (517), Spring washer (516) and Washer (515) on each side as shown.

ASSEMBLY

516

515

517

515

A06

www.cybexinternational.com 22

STEP 3:

Attach the Left Pedal Swing Arm (106) and Right Pedal Swing Arm (105) with the pivoting bracket on the main frame
as shown and secure with M12x70 shoulder bolt (504), 18x12xT3.5 washer (511), 18x12xT3 washer (512) and M12
Nylon Nut (508) on each side. Important Note: The shoulder bolt must be inserted into the pivoting bracket
completely, no gap should exist between the shoulder bolt head and the pivoting bracket. See Figure below.

ASSEMBLY

504

511

512

508

512

511

504

105

106

www.cybexinternational.com 23

STEP 4:

Place the Pedal soft cushion (363) on the Pedal (358,359 ) and place the Pedal on the Pedal Arm and secure the
Pedal with 4-M6x12 Screws ( 506 ) from the bottom of pedal as shown .

ASSEMBLY

363

359

A09

506

A08

506

359

358

www.cybexinternational.com 24

STEP 5:

Place spacers on the right and left side of the handlebar shaft (321). Line up the Left Handlebar (A02) lower pivot
housing with the shaft on the main frame and the shaft on the Left Handlebar with the Linkage (113), then push both
pivot joints in at the same time. Secure the handlebar with Flat hex head bolt M8x16 (501) and Washer 30x8xT2.0
(510) on the lower pivot joint. Secure the handle bar to the Linkage (113) with the Button head cap screw M6x16
(502), Cap (361) and Washer 16x6xT2 (509). Repeat the same procedure for the right hand side.

ASSEMBLY

www.cybexinternational.com 25

STEP 6:

Rotate the Left Crank to the lowest position as shown below. Important Note: Failure to rotate the crank arm to
the proper position will not allow the unit to be assembled properly. Place the Crank Bushing (505) on the Left

Crank Shaft (434) and then mount the Left Crank-Pedal Link Bar (110) on the left crank shaft, attach the washer (510)
and Cap (360) on and secure with M8x16 Flat Allen head bolt (501) as shown. Repeat the same procedure on the
right hand side.

ASSEMBLY

www.cybexinternational.com 26

503

STEP 7:

With a person holding the console, connect the 12 Pin Upper Cable (610) with the 12 Pin Lower Cable (611). Connect
the 4 Pin Upper Hand Pulse Cable (615) and 4 Pin Lower Hand Pulse Cable (616), Insert the extra length of cables
into the Console Assembly and insert the 12 pin connector into the hole on Front Tower then place the Console
Assembly onto the Front Tower as shown. Ensure tight and proper connection between the cables. Important Note:

The half-round hole on the Console Assembly bottom bracket must match with the pins welded on the Front Tower
before tightening the Console Assembly with the Front Tower. Secure the Console Assembly with 2 M8x25 Bolts

(503). Insert 6 pieces Nylon Pin (230) into the Front Tower Cover (351 ), mount the Front Tower Cover (351) and Rear
Tower Cover ( 352) together to cover the connection at the main frame as shown then secure them with 2 4x19 Flat
Head Philip screws (507) as shown. NOTE: When tightening the console to the main frame, Do Not tighten one side

all the way down before the other side. Tighten each side down equally small amounts at a time.

ASSEMBLY

116

503

352 116

615

616

610

611

507

351

616

610

615

611

www.cybexinternational.com 27

STEP 8:

Insert 3 pieces Nylon Pin (230) into the Left/Outer Frame Join Cover (356 ), mount the Left/Outer and Left/Inner
Frame Join Cover (355 ) to cover the left hand side frame joint and secure them with 4 -4x15 taper screws (514) and
2 -4x19 Flat Head Philip screws (507). See Figure below. Repeat the same procedure for the right hand side frame
joint.

ASSEMBLY

362

101

514

355

230

230

356

514

507

354

230

362

230

353

514

www.cybexinternational.com 28

STEP 9:

Lift the front end and attach the Level Adjustment (513) underneath the front stabilizer tube. Level the Home Arc
Trainer so it does not move or rock. All assembly steps are now completed. Plug unit into a dedicated wall outlet.

NOTE: The Home Arc Trainer should be plugged into a dedicated line or circuit.

ASSEMBLY

101

513

www.cybexinternational.com 29

COMPUTER OPERATION

CM-EC-M350A-2

CM-EC-M360A-01

CM-EC-M350A-21

CM-EC-M360A-02

www.cybexinternational.com 30

COMPUTER OPERATION

M

A

B

C
D
E

F G H I J K L

SCAN

INCLINE UP C

INCLINE DOWN E

STRIDES/min K

ADJUSTMENT BUTTON-UP O

ADJUSTMENT BUTTON-DOWN Q

RESISTANCE UP S

RESISTANCE DOWN U

CALORIES G

METs I

ENTER M

A

CM-EC-M350A-2

CM-EC-M360A-01

CM-EC-M350A-21

CM-EC-M360A-02

B CHOOSE PROGRAM Buttons

D PAUSE/END

F DISTANCE

H CAL/hr

J DISTANCE CLIMBED

L HEART RATE

N TIME

P LEVEL

R WEIGHT

T QUICK START

N
O
P

Q
R

S

T
U

Buttons:

Program Buttons:

P12 – Hill Interval program.

Data Display Control buttons:

COMPUTER OPERATION

Manual: Program button. Press to select P1 manual adjustment program.

Calories: Program button. Press to select P2 target calories burns program.

Random: Program button. Press to select P3 Random workout program.

Fitness: Program button. Press to select 3 Fitness programs :

P4 – Weight Loss program.
P5 – Cardio Program.
P6 – Endurance Program.

Hills: Program button. Press to select 3 Hills programs :

P7 – Hill Program
P8 – Valleys Program
P9 – Ramps Program.

Interval: Program button. Press to select 3 Interval programs :

P10 – Interval 2 to 1 program.
P11 – Interval 1 to 1 program.

Scan: Press to display all workout data revolving on the center LED display window during the workout.
Functions activate when Scan LED lights on. When each data showing on the center LED window, the
corresponds button LED will be on at the same time.

Dist.: Press to deactivate other data display functions and show accumulated workout distance on center
LED display window during the workout. Function activates when Dist. LED lights on.

Cal.: Press to deactivate other data display functions and show accumulated calories burns on center LED
display window during the workout. Function activates when Cal. LED lights on.

Cal/Hr.: Press to deactivate other data display function and shows the average calories burns per hour on
center LED display window during the workout. Function activates when Cal/Hr. LED lights on.

Distance Climbed: Press to deactivate other data display functions and shows current climbed distance on
center LED display window during the workout. Function activates when Distance Climbed LED lights on.

Strides per Minute: Press to deactivate other data display function and shows the workout speed by
Strides per minute on center LED display window during the workout. Function activate when Strides per
Minute LED lights on.

www.cybexinternational.com 31

www.cybexinternational.com 32

COMPUTER OPERATION

Heart Rate: Press to deactivate other data display functions and show the workout heart rate on the center

LED display window during the workout. Function activates when Heart Rate LED lights on.

Enter: Press to confirm the input workout Time, Level and user Weight during workout program set up

procedure.

Up Arrow: Press to increase the workout Time, Level and User Weight during workout program set up

procedure.

Down Arrow: Press to decrease the workout Time, Level and User Weight during workout program set up

procedure.

Time: Press to select workout time and adjustment.

Level: Press to select workout level and adjustment.

Weight: Press to select user weight and adjustment.

Quick Start: Press to activate the Quick Start program.

Resistance +: Press to increase the resistance level during the workout.

Resistance -: Press to reduce the resistance level during the workout.

Pause / End: Press to pause or end the program during workout. Press once to pause the program, press

twice to enter the Dormant State.

www.cybexinternational.com 33

OPERATING INSTRUCTIONS:

Dormant State: Connect the power cord, turn on the power switch located at front end, LED dot matrix display shows

Cybex logo for 3 seconds and then enters the Dormant State. Before stepping on the pedal or pressing any program
buttons including the Quick Start button, the unit will stay in the Dormant State. All LED windows are off except the
LED dot matrix display which shows the blinking heart sign and 6 program buttons LED indication lights on and off in
rotation. While on the Dormant State, you can press the Quick Start button to start the workout, or press any program
button to start configuring the program or directly stepping the pedal for 20 seconds to start the workout. If pressing
any other buttons, a beep will be sounded and the LED dot matrix display will show an arrow sign to point the program
button’s direction.

Program State: While on the Dormant or Active State, press one of the 6 program buttons then press the Enter
button. The Home Arc Trainer will be entered into the Program State. Follow the program set up instructions to
complete the program configuration and start the workout. User must press the Enter button after completing the
program set up in order to store all the data into the console for the workout. Failure to press the Enter button will
result in all the set up data being lost and the Home Arc Trainer not entering the Active State. If the Start button is
pressed without pressing the Enter button first, the Home Arc Trainer will perform the Quick Start function at the
default user weight of 150 lb ( 68 kgs ) and default workout time of 20 minutes.

Active State: While on the Dormant State, press Quick Start or begin stepping on the pedals for 20 seconds. The
Home Arc Trainer will be entered into the Active State. Or press any of the program buttons, complete the program
setup procedure and start the workout and the Home Arc Trainer will be also entered the Active State. The Active
State will be ended when the Pause/End button is pressed during the workout or the preset workout time is up.

Review State: After completing the Active State, the display will be entered into the Review State for the user to
review the workout result. The review state period lasts for 20 seconds. After 20 seconds, the Home Arc Trainer will
be entered into the Dormant State automatically.

Quick Start: While in Dormant State, press Quick Start button to start the workout. The time display will count up and
the user weight is based on the default setting of 150 lb (68 KGS).

Program Set Up and Operating:

Manual: While in the Dormant State, press the Manual button. The center LED window will show “P1”. Press the

Enter button (If the Enter button is not pressed within 10 seconds, this procedure will be skipped to the next step, user

weight set up), and the center LED window will then show the default user weight “150” (LB) while the LED dot matrix window
shows “LBS”. Press the Up or Down Arrow buttons to set up user weight and then press Enter (If the Enter button is not pressed
within 10 seconds, this procedure will be skipped to the next step workout time, set up), and the center LED window shows default
workout time “20”(Minutes) and the LED dot matrix window shows “MIN”. Press the Up or Down Arrow buttons to set up the target
workout time then press the Enter button to start the workout. The center LED window starts counting down 3 seconds then starts
the manual program. Time counts down from the set workout time to 0:00. During the workout, the user can press the Incline + and
Incline – buttons to adjust the incline level from 0 to 10 and press Resistance + and Resistance – buttons to adjust the resistance
level from 1 to 20.

COMPUTER OPERATION

Incline +: Press to increase the incline level during the workout..

Incline -: Press to decrease the incline level during the workout.

www.cybexinternational.com 34

Calorie: While on the Dormant State, press the Calories button. The center LED window shows “P2”. Press the Enter button and

the center LED window then shows “0” while the LED dot matrix window shows “CAL”. Press the Up or Down Arrow buttons to set
up the target calories from 20 up to 9999. Then press Enter and the center LED window then shows the default user weight “150”
(LB) while the LED dot matrix window shows “LBS”. Press the Up or Down Arrow buttons to set up user weight. Then press Enter
and the center LED window starts to count down 3 seconds before beginning the Calories program. Time counts up from 0:00 and
Calories counts up to the set up target calories. During the workout, the user can press the Incline + and Incline – button to adjust
the incline level from 0 to 10. Press the Resistance + and Resistance – buttons to adjust the resistance level from 1 to 20.

Random: While on the Dormant State, press the Random button. The center LED window shows “P3”. Press the Enter button (If
the Enter button is not pressed within 10 seconds, this procedure will be skipped to the next step, user weight set up) and the
center LED window then shows the default user weight “150” (LB). The LED dot matrix window shows “LBS”. Press the Up or
Down Arrow buttons to set up user weight. Then press Enter (If the Enter button is not pressed within 10 seconds, this procedure
will be skipped to the next step, workout time set up) and the center LED window shows default workout time “20”(Minutes). The
LED dot matrix window shows “MIN”. Press the Up or Down Arrow buttons to set up target workout time and then press the Enter
button. The center LED window shows workout level “1” and the LED dot matrix window shows “LVL”. Press the Up and Down
Arrow buttons to select the workout level from 1 to 10 and then press the Enter button to start the workout. The center LED window
starts the count down for 3 seconds and then starts the Random program. Time counts down from set up workout time to 0:00.
During the workout, the user can press the Incline + and Incline – buttons to overwrite the preset profile and adjust the incline level
from 0 to 10. Press Resistance + and Resistance – buttons during the workout to overwrite the preset profile and adjust the
resistance level from 1 to 20. The overwrite will only last for one segment of workout and then the next segment will return to the
original preset profile.

Fitness Programs: While on the Dormant State, press Fitness button. The center LED window shows “P4”. Press the Enter
button to select P4 and start the user weight set up. Or press the Up or Down Arrow buttons to select among P4 to P6. Then press
the Enter button to start the user weight set up (If the Enter button is not pressed within 10 seconds, this procedure will be skipped
to the next step, user weight set up) and the center LED window then shows the default user weight “150” (LB) while the LED dot
matrix window shows “LBS”. Press the Up or Down Arrow buttons to set up user weight then press Enter (If the Enter button is not
pressed within 10 seconds, this procedure will be skipped to the next step, workout time set up) and the center LED window shows
default workout time “20”(Minutes) while the LED dot matrix window shows “MIN”. Press the Up or Down Arrow buttons to set up
the target workout time and then press the Enter button. The center LED window shows workout level “1” and the LED dot matrix
window shows “LVL”. Press the Up and Down Arrow buttons to select the workout level from 1 to 10 and then press the Enter
button to start the workout. The center LED window starts count down 3 seconds before starting the selected Fitness program.
Time counts down from set up workout time to 0:00. During the workout, the user can press the Incline + and Incline – buttons to
overwrite the preset profile and adjust the incline level from 0 to 10. Press the Resistance + and Resistance – buttons during the
workout to overwrite the preset profile and adjust the resistance level from 1 to 20. The overwrite will only last for one segment of
workout and then the next segment will return to the original preset profile. (If the Enter button is not pressed within 10 seconds,
this procedure will be skipped to the next step, user weight set up) and the center LED window then shows the default user weight
“150” (LB) while the LED dot matrix window shows “LBS”. Press the Up or Down Arrow buttons to set up user weight and then
press Enter (If the Enter button is not pressed within 10 seconds, this procedure will be skipped to the next step, workout time set
up) and the center LED window shows default workout time “20”(Minutes) while the LED dot matrix window shows “MIN”.
Press the Up or Down Arrow buttons to set up the target workout time and then press the Enter button. The center LED window
shows workout level “1” and the LED dot matrix window shows “LVL”. Press the Up and Down Arrow buttons to select the workout
level from 1 to 10 and then press the Enter button to start the workout. The center LED window will count down 3 seconds before
the selected Fitness program begins. Time counts down from set up workout time to 0:00. During the workout, the user can press
Incline + and Incline – buttons to overwrite the preset profile and adjust the incline level from 0 to 10. Press the Resistance + and
Resistance – buttons to overwrite the preset profile and adjust the resistance level from 1 to 20. The overwrite will only last for one
segment of workout and then the next segment will return to the original preset profile.

COMPUTER OPERATION

www.cybexinternational.com 35

COMPUTER OPERATION

P-4 Weight Loss

The Weight Loss program is designed for low to medium intensity training that the user can sustain for an extended period of time.
It builds from a low intensity baseline to include segments of higher incline and resistance as well as segments that use higher
resistance at the base incline. The constant variety provides for periods of higher energy expenditure and training effect with less
fatigue, allowing the user to exercise for longer periods of time.

Weight Loss

:30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30

Level

Resistance

10 1 2 3 4 5 5 9 9 9 9 5 5 9 9 5 5 4 3 2 1

9 1 2 3 4 5 5 8 8 8 8 5 5 8 8 5 5 4 3 2 1

8 1 2 3 4 5 5 7 7 7 7 5 5 7 7 5 5 4 3 2 1

7 1 1 2 3 5 5 8 8 8 8 5 5 8 8 5 5 3 2 1 1

6 1 1 2 3 5 5 7 7 7 7 5 5 7 7 5 5 3 2 1 1

5 1 1 2 3 5 5 6 6 6 6 5 5 6 6 5 5 3 2 1 1

4 1 1 1 2 3 3 5 5 5 5 3 3 5 5 3 3 2 1 2 2

3 1 1 1 2 3 3 4 4 4 4 3 3 4 4 3 3 2 1 2 2

2 1 1 1 1 1 1 3 3 3 3 1 1 3 3 1 1 1 1 1 1

1 1 1 1 1 1 1 2 2 2 2 1 1 2 2 1 1 1 1 1 1

Warm Up Program Segments Cool Down

Incline 1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4

10 4 4 4 4 4 4 6 6 6 6 4 4 4 4 4 4 4 4 4 4

9 4 4 4 4 4 4 6 6 6 6 4 4 4 4 4 4 4 4 4 4

8 3 3 3 3 3 3 6 6 6 6 3 3 3 3 3 3 3 3 3 3

7 3 3 3 3 3 3 4 4 4 4 3 3 3 3 3 3 3 3 3 3

6 3 3 3 3 3 3 4 4 4 4 3 3 3 3 3 3 3 3 3 3

5 3 3 3 3 3 3 4 4 4 4 3 3 3 3 3 3 3 3 3 3

4 2 2 2 2 2 2 3 3 3 3 2 2 2 2 2 2 2 2 2 2

3 2 2 2 2 2 2 3 3 3 3 2 2 2 2 2 2 2 2 2 2

2 2 2 2 2 2 2 3 3 3 3 2 2 2 2 2 2 2 2 2 2

1 2 2 2 2 2 2 3 3 3 3 2 2 2 2 2 2 2 2 2 2

Warm Up Program Segments Cool Down

1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4

Time

www.cybexinternational.com 36

COMPUTER OPERATION

P-5 Cardio

The Cardio program is designed for experienced users that desire a high intensity cardiovascular training experience. The 2-minute
work interval with high resistance ensures that the aerobic energy system is completely taxed, while the subsequent 2-minute
recovery interval enables a repeat at the higher work rate. Additionally, a higher incline level is used during the recovery interval to
discourage blood pooling ensuring more complete recovery.

CARDIO TIME

Resistance

Level

10 6 7 9 11 16 16 16 16 12 12 12 12 11 9 7 6

9 5 7 9 11 15 15 15 15 11 11 11 11 11 9 7 5
8 5 6 8 9 14 14 14 14 10 10 10 10 9 8 6 5
7 4 5 7 8 13 13 13 13 9 9 9 9 8 7 5 4
6 3 4 6 7 12 12 12 12 8 8 8 8 7 6 4 3
5 3 4 5 6 11 11 11 11 7 7 7 7 6 5 4 3
4 2 3 4 5 10 10 10 10 6 6 6 6 5 4 3 2
3 1 2 3 4 9 9 9 9 6 6 6 6 4 3 2 1
2 1 1 2 3 8 8 8 8 5 5 5 5 3 2 1 1
1 1 1 1 2 7 7 7 7 4 4 4 4 2 1 1 1

Warm Up Program Segments Cool Down

Incline

10 3 4 5 6 5 5 5 5 8 8 8 8 6 5 4 3

9 3 3 4 5 5 5 5 5 8 8 8 8 5 4 3 3
8 3 3 4 4 5 5 5 5 7 7 7 7 4 4 3 3
7 3 3 4 4 4 4 4 4 7 7 7 7 4 4 3 3
6 3 3 3 4 4 4 4 4 6 6 6 6 4 3 3 3
5 3 3 3 3 4 4 4 4 6 6 6 6 3 3 3 3
4 2 2 2 3 3 3 3 3 5 5 5 5 3 2 2 2
3 2 2 2 3 3 3 3 3 5 5 5 5 3 2 2 2
2 2 2 2 2 2 2 2 2 4 4 4 4 2 2 2 2
1 2 2 2 2 2 2 2 2 4 4 4 4 2 2 2 2

:30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30

Warm Up Program Segments Cool Down

1 2 3 4 1 2 3 4 5 6 7 8 1 2 3 4

1 2 3 4 1 2 3 4 5 6 7 8 1 2 3 4

www.cybexinternational.com 37

P-6 Endurance

The Endurance program challenges the cardiovascular system in a manner that adjusts the overall intensity to accommodate for
fatigue but maintains a similar perceived exertion throughout the workout. The core program is 16 minutes in length. After warm-up
the intensity is increased over the next four minutes. Peak intensity is maintained for the next two minutes and then gradually
tapers off during the following ten minutes.

COMPUTER OPERATION

Endurance

:30 :30 :30 :30 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 :30 :30 :30 :30

Level Warm Up Program Segments Cool Down

Resistance 1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4

10 4 6 8 10 12 16 16 20 20 20 18 18 18 16 16 16 14 14 14 12 10 8 6 4

9 4 6 8 9 11 15 15 19 19 19 17 17 17 15 15 15 13 13 13 11 9 8 6 4
8 4 6 7 8 10 14 14 18 18 18 16 16 16 14 14 14 12 12 12 10 8 7 6 4

7 3 5 7 7 9 13 13 17 17 17 15 15 15 13 13 13 11 11 11 9 7 7 5 3
6 3 5 6 7 8 12 12 16 16 16 14 14 14 12 12 12 10 10 10 8 7 6 5 3

5 3 5 6 6 7 11 11 15 15 15 13 13 13 11 11 11 9 9 9 7 6 6 5 3
4 2 4 5 6 6 10 10 14 14 14 12 12 12 10 10 10 8 8 8 6 6 5 4 2

3 2 4 5 5 5 9 9 13 13 13 11 11 11 9 9 9 7 7 7 5 5 5 4 2
2 2 3 4 5 4 8 8 12 12 12 10 10 10 8 8 8 6 6 6 4 5 4 3 2

1 2 2 3 3 3 7 7 11 11 11 9 9 9 7 7 7 5 5 5 3 3 3 2 2

Warm Up Program Segments Cool Down

Incline 1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4

10 3 4 5 6 8 10 10 10 10 10 10 10 10 10 10 10 9 9 9 8 6 5 4 3

9 3 3 4 5 7 9 9 10 10 10 9 9 9 9 9 9 8 8 8 7 5 4 3 3

8 3 3 4 4 7 9 9 9 9 9 9 9 9 9 9 9 8 8 8 7 4 4 3 3
7 3 3 4 4 6 8 8 9 9 9 8 8 8 8 8 8 7 7 7 6 4 4 3 3

6 3 3 3 4 6 8 8 8 8 8 8 8 8 8 8 8 7 7 7 6 4 3 3 3

5 3 3 3 3 5 7 7 8 8 8 7 7 7 7 7 7 6 6 6 5 3 3 3 3

4 2 2 2 3 5 7 7 7 7 7 7 7 7 7 7 7 6 6 6 5 3 2 2 2

3 2 2 2 3 4 6 6 7 7 7 6 6 6 6 6 6 5 5 5 4 3 2 2 2
2 2 2 2 2 4 6 6 6 6 6 6 6 6 6 6 6 5 5 5 4 2 2 2 2

1 2 2 2 2 3 5 5 6 6 6 5 5 5 5 5 5 4 4 4 3 2 2 2 2

Hills Programs : While on the Dormant State, press Hills button. The center LED window shows “P7”. Press the Enter button to
select P7 and start the user weight set up. Or press the Up or Down Arrow buttons to select among P7 to P9.Then press Enter
button to start the user weight set up (If the Enter button is not pressed within 10 seconds, this procedure will be skipped to the
next step, user weight set up) and the center LED window then shows the default user weight “150” (LB) while the LED dot matrix
window shows “LBS”. Press the Up or Down Arrow buttons to set up user weight and then press Enter (If the Enter button is not
pressed within 10 seconds, this procedure will be skipped to the next step, workout time set up) and the center LED window shows
default workout time “20”(Minutes) while the LED dot matrix window shows “MIN”. Press the Up or Down Arrow buttons to set up
the target workout time and then press the Enter button. The center LED window shows workout level “1” and the LED dot matrix
window shows “LVL”. Press the Up and Down Arrow buttons to select the workout level from 1 to 10 and then press the Enter
button to start the workout. The center LED window will count down 3 seconds before the selected Fitness program begins. Time
counts down from set up workout time to 0:00. During the workout, the user can press Incline + and Incline – buttons to overwrite
the preset profile and adjust the incline level from 0 to 10. Press the Resistance + and Resistance – buttons to overwrite the
preset profile and adjust the resistance level from 1 to 20. The overwrite will only last for one segment of workout and then the next
segment will return to the original preset profile.

TIME

www.cybexinternational.com 38

P-7 Hills

The Hills program uses a 3 ½ minute core in which the incline and resistance both increase over the first 2 ½ minutes, followed by
a one-minute reduction in incline and resistance. The reduced workload simulates reaching the top of the hill. The climb is then
repeated.

COMPUTER OPERATION

Hills TIME

Level

Resistance 1 2 3 4 1 2 3 4 5 6 7 1 2 3 4

10 4 6 8 10 12 14 16 18 20 12 12 10 8 6 4

9 4 6 8 9 11 13 15 17 19 11 11 9 8 6 4
8 4 6 7 8 10 12 14 16 18 10 10 8 7 6 4
7 3 5 7 7 9 11 13 15 17 9 9 7 7 5 3

6 3 5 6 7 8 10 12 14 16 8 8 7 6 5 3
5 3 5 6 6 7 9 11 13 15 7 7 6 6 5 3

4 2 4 5 6 6 8 10 12 14 6 6 6 5 4 2
3 2 4 5 5 5 7 9 11 13 5 5 5 5 4 2

2 2 3 4 5 4 6 8 10 12 4 4 5 4 3 2
1 2 2 3 3 3 5 7 9 11 3 3 3 3 2 2

Warm Up Program Segments Cool Down

Incline 1 2 3 4 1 2 3 4 5 6 7 1 2 3 4

10 3 4 5 6 8 9 10 10 10 5 5 6 5 4 3

9 3 3 4 5 7 8 9 9 10 5 5 5 4 3 3
8 3 3 4 4 7 8 9 9 9 5 5 4 4 3 3
7 3 3 4 4 6 7 8 8 9 5 5 4 4 3 3
6 3 3 3 4 6 7 8 8 8 5 5 4 3 3 3

5 3 3 3 3 5 6 7 7 8 5 5 3 3 3 3
4 2 2 2 3 5 6 7 7 7 5 5 3 2 2 2

3 2 2 2 3 4 5 6 6 7 5 5 3 2 2 2
2 2 2 2 2 4 5 6 6 6 5 5 2 2 2 2

1 2 2 2 2 3 4 5 5 6 5 5 2 2 2 2

:30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30

Warm Up Program Segments Cool Down

www.cybexinternational.com 39

P-8 Valleys

The Valleys program provides a contrasting mix of incline and resistance. The program uses a five minute core during which the
resistance is increased and the incline is reduced over the first three minutes, followed by a reduction in resistance and an
increased incline until the valley repeats itself. This program is designed specifically to contrast the Ramps and Hills programs for
added training variety.

COMPUTER OPERATION

Valleys TIME

Level

Resistance 1 2 3 4 1 2 3 4 5 6 7 8 9 10 1 2 3 4

10 4 5 6 8 11 11 16 16 20 20 16 16 11 11 8 6 5 4

9 4 5 6 7 10 10 14 14 18 18 14 14 10 10 7 6 5 4

8 4 5 6 7 9 9 12 12 16 16 12 12 9 9 7 6 5 4

7 3 4 5 7 8 8 10 10 14 14 10 10 8 8 7 5 4 3

6 3 4 5 6 7 7 9 9 12 12 9 9 7 7 6 5 4 3

5 2 3 4 4 6 6 8 8 10 10 8 8 6 6 4 4 3 2

4 2 2 3 3 5 5 6 6 8 8 6 6 5 5 3 3 2 2

3 1 2 2 3 4 4 5 5 6 6 5 5 4 4 3 2 2 1

2 1 1 2 2 3 3 3 3 4 4 3 3 3 3 2 2 1 1

1 1 1 2 2 2 2 3 3 3 3 3 3 2 2 2 2 1 1

Warm Up Program Segments Cool Down

Incline

10 3 4 5 5 10 10 5 5 1 1 5 5 10 10 5 5 4 3

9 3 4 5 5 10 10 4 4 1 1 4 4 10 10 5 5 4 3

8 3 4 4 4 9 9 4 4 1 1 4 4 9 9 4 4 4 3

7 3 3 4 4 9 9 4 4 1 1 4 4 9 9 4 4 3 3

6 3 3 4 4 8 8 3 3 1 1 3 3 8 8 4 4 3 3

5 3 3 4 4 7 7 3 3 1 1 3 3 7 7 4 4 3 3

4 3 3 4 4 6 6 3 3 1 1 3 3 6 6 4 4 3 3

3 3 3 4 4 5 5 2 2 1 1 2 2 5 5 4 4 3 3

2 3 3 4 4 4 4 2 2 1 1 2 2 4 4 4 4 3 3

1 3 3 4 4 3 3 2 2 1 1 2 2 3 3 4 4 3 3

:30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30

Warm Up Program Segments Cool Down

1 2 3 4 1 2 3 4 5 6 7 8 9 10 1 2 3 4

www.cybexinternational.com 40

P-9 Ramps

The Ramps program is similar to the Hills program but uses a more linear ramp of both incline and resistance from segment to
segment. Ramps is comprised of a 3 ½ minute core during which the incline and resistance both increase over the first 2 ½
minutes, followed by a one-minute reduction of both incline and resistance. The reduction in incline and resistance provides a
working rest period before the ramp is repeated.

COMPUTER OPERATION

RAMPS TIME

Resistance

Level

10 4 6 8 10 12 14 16 18 20 12 12 10 8 6 4

9 4 6 8 9 11 13 15 17 19 11 11 9 8 6 4

8 4 6 7 8 10 12 14 16 18 10 10 8 7 6 4

7 3 5 7 7 9 11 13 15 17 9 9 7 7 5 3

6 3 5 6 7 8 10 12 14 16 8 8 7 6 5 3

5 3 5 6 6 7 9 11 13 15 7 7 6 6 5 3

4 2 4 5 6 6 8 10 12 14 6 6 6 5 4 2

3 2 4 5 5 5 7 9 11 13 5 5 5 5 4 2

2 2 3 4 5 4 6 8 10 12 4 4 5 4 3 2

1 2 2 3 3 3 5 7 9 11 3 3 3 3 2 2

Warm Up Program Segments Cool Down

Incline

10 3 4 5 6 8 8 9 10 10 5 5 6 5 4 3

9 3 3 4 5 7 8 8 9 10 5 5 5 4 3 3

8 3 3 4 4 7 7 8 9 9 5 5 4 4 3 3

7 3 3 4 4 6 7 7 8 9 5 5 4 4 3 3

6 3 3 3 4 6 6 7 8 8 5 5 4 3 3 3

5 3 3 3 3 5 6 6 7 8 5 5 3 3 3 3

4 2 2 2 3 5 5 6 7 7 5 5 3 2 2 2

3 2 2 2 3 4 5 5 6 7 5 5 3 2 2 2

2 2 2 2 2 4 4 5 6 6 5 5 2 2 2 2

1 2 2 2 2 3 4 4 5 6 5 5 2 2 2 2

:30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30

Warm Up Program Segments Cool Down

1 2 3 4 1 2 3 4 5 6 7 1 2 3 4

1 2 3 4 1 2 3 4 5 6 7 1 2 3 4

www.cybexinternational.com 41

Interval Programs: While on the Dormant State, press Interval button. The center LED window shows “P10”. Press the Enter

button to select P10 and start the user weight set up. Or press the Up or Down Arrow buttons to select among P10 to P12. Then
press the Enter button to start the user weight set up (If Enter button is not pressed within 10 seconds, this procedure will be
skipped to the next step, user weight set up) and the center LED window then shows the default user weight “150” (LB) while the
LED dot matrix window shows “LBS”. Press the Up or Down Arrow buttons to set up user weight then press Enter (If the Enter
button is not pressed within 10 seconds, this procedure will be skipped to the next step, workout time set up) and the center LED
window shows default workout time “20”(Minutes) while the LED dot matrix window shows “MIN”. Press the Up or Down Arrow
buttons to set up the target workout time then press the Enter button. The center LED window shows workout level “1” and the
LED dot matrix window shows “LVL”. Press the Up and Down Arrow buttons to select the workout level from 1 to 10 then press the
Enter button to start the workout. The center LED window will count down 3 seconds before start the selected Fitness program
begins. Time counts down from set up workout time to 0:00. During the workout, the user can press Incline + and Incline – buttons
to overwrite the preset profile and adjust the incline level from 0 to 10. Press Resistance + and Resistance – buttons to overwrite
the preset profile and adjust the resistance level from 1 to 20. The overwrite will only last for one segment of workout and then the
next segment will return to the original preset profile.

COMPUTER OPERATION

P-10 Interval 1

This program introduces the user to higher intensity training. The program employs a fixed incline with variable resistance, applied
in repeated work-rest intervals. Each work segment lasts 30 seconds while each rest segment lasts 60 seconds. The resistance of
the rest segments is 60 to 65% of the work segments. Interval training develops both the aerobic and anaerobic energy systems.
During the high intensity segments the anaerobic energy system is used. During the low intensity segments the aerobic energy
system works to repay the “oxygen debt” incurred during the high intensity segments. The repetition of the high intensity segments
forces the body to adapt to higher demands thereby helping the user to develop enhanced performance capabilities.

Interval 1:1 TIME

Level Warm Up Program Segments Cool Down

Resistance

10 4 6 7 8 20 20 10 10 8 7 6 4

9 3 5 6 7 19 19 10 10 7 6 5 3
8 3 4 5 6 18 18 9 9 6 5 4 3
7 2 4 5 6 17 17 9 9 6 5 4 2
6 2 4 5 6 16 16 8 8 6 5 4 2
5 2 3 4 5 14 14 8 8 5 4 3 2
4 3 4 4 5 12 12 7 7 5 4 4 3
3 2 2 3 4 10 10 7 7 4 3 2 2
2 1 2 3 4 8 8 6 6 4 3 2 1
1 1 2 3 3 6 6 6 6 3 3 2 1

Warm Up Program Segments Cool Down

Incline

10 2 2 3 4 5 5 5 5 4 3 2 2

9 2 2 3 4 5 5 5 5 4 3 2 2
8 2 2 3 3 4 4 4 4 3 3 2 2
7 2 2 3 3 4 4 4 4 3 3 2 2
6 2 2 3 3 4 4 4 4 3 3 2 2
5 2 2 2 3 3 3 3 3 3 2 2 2
4 2 2 2 2 3 3 3 3 2 2 2 2
3 2 2 2 2 3 3 3 3 2 2 2 2
2 2 2 2 2 2 2 2 2 2 2 2 2
1 2 2 2 2 2 2 2 2 2 2 2 2

:30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30

1 2 3 4 1 2 3 4 1 2 3 4

1 2 3 4 1 2 3 4 1 2 3 4

www.cybexinternational.com 42

P-11 Interval 2

This program is designed for those who desire a higher intensity interval training program. It uses a fixed incline with variable
resistance applied in a repeating 1:1 work to rest ratio. Each work and rest segment lasts 60 seconds. The resistance of the rest
segments is approximately 55 to 65% of the work segments. Interval training is designed to tax both the aerobic and anaerobic
energy systems. During the high intensity segments the anaerobic energy system is used. During the low intensity segments the
aerobic energy system works to repay the “oxygen debt” incurred during the high intensity segments In Interval 2 the extended work
segment creates a greater “oxygen debt” than Interval 1 putting greater demand on both energy systems, forcing even greater
adaptation to the imposed demands.

COMPUTER OPERATION

Interval 2:1 TIME

Level

Resistance 1 2 3 4 1 2 3 1 2 3 4

10 7 9 11 13 14 9 9 8 7 6 4

9 7 8 10 12 13 8 8 7 6 5 3
8 6 8 10 11 12 7 7 6 5 4 3
7 6 7 9 10 11 6 6 6 5 4 2
6 5 7 8 9 10 6 6 6 5 4 2
5 5 6 7 8 9 5 5 5 4 3 2
4 4 5 6 7 8 5 5 5 4 3 2
3 4 5 6 6 7 4 4 4 3 2 2
2 3 4 5 6 6 4 4 4 3 2 1
1 2 3 4 4 5 3 3 3 3 2 1

Warm Up Program Segments

Incline

10 2 2 3 4 5 5 5 4 3 2 2

9 2 2 3 4 5 5 5 4 3 2 2
8 2 2 3 3 4 4 4 3 3 2 2
7 2 2 3 3 4 4 4 3 3 2 2
6 2 2 3 3 4 4 4 3 3 2 2
5 2 2 2 3 3 3 3 3 2 2 2
4 2 2 2 2 3 3 3 2 2 2 2
3 2 2 2 2 3 3 3 2 2 2 2
2 2 2 2 2 2 2 2 2 2 2 2
1 2 2 2 2 2 2 2 2 2 2 2

:30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30

Warm Up Program Segments

Cool Down

Cool Down

1 2 3 4 1 2 3 1 2 3 4

www.cybexinternational.com 43

P-12 Hill Interval

The Hills program is designed to give the user the experience of hiking in hilly terrain. This program uses intervals of moderate
resistance and incline to simulate relatively flat areas and intervals of substantially greater incline and resistance to simulate
steeper grades. The two-minute work segments offer a more prolonged interval challenge, while the equal rest period allows for
adequate recuperation.

COMPUTER OPERATION

Hills TIME

:30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30 :30

Level

Resistance 1 2 3 4 1 2 3 4 5 6 7 8 1 2 3 4

10 4 5 6 7 8 8 8 8 12 12 12 12 7 6 5 4

9 4 5 6 7 8 8 8 8 10 10 10 10 7 6 5 4
8 3 4 5 6 7 7 7 7 9 9 9 9 6 5 4 3
7 3 4 5 6 7 7 7 7 8 8 8 8 6 5 4 3
6 3 3 4 5 6 6 6 6 7 7 7 7 5 4 3 3
5 3 3 4 5 6 6 6 6 5 5 5 5 5 4 3 3
4 2 2 3 4 5 5 5 5 6 6 6 6 4 3 2 2
3 2 2 3 4 5 5 5 5 5 5 5 5 4 3 2 2
2 2 2 2 3 4 4 4 4 4 4 4 4 3 2 2 2
1 2 2 2 2 3 3 3 3 3 3 3 3 2 2 2 2

Warm Up Program Segments Cool Down

Incline 1 2 3 4 1 2 3 4 5 6 7 8 1 2 3 4

10 3 4 5 6 6 6 6 6 10 10 10 10 6 5 4 3

9 3 3 4 5 5 5 5 5 10 10 10 10 5 4 3 3
8 3 3 4 5 5 5 5 5 9 9 9 9 5 4 3 3
7 3 3 3 4 4 4 4 4 9 9 9 9 4 3 3 3
6 3 3 3 4 4 4 4 4 8 8 8 8 4 3 3 3
5 3 3 3 3 3 3 3 3 8 8 8 8 3 3 3 3
4 3 3 3 3 3 3 3 3 7 7 7 7 3 3 3 3
3 2 2 3 3 3 3 3 3 7 7 7 7 3 3 2 2
2 2 2 3 3 3 3 3 3 6 6 6 6 3 3 2 2
1 2 2 3 3 3 3 3 3 6 6 6 6 3 3 2 2

Warm Up Program Segments Cool Down

www.cybexinternational.com 44

Warning:

Before using this product, please consult your personal physician for a complete physical examination. Frequent and strenuous
exercise should be approved by your doctor first. If any discomfort should result from your use of this product, stop exercising and
consult your doctor. Proper usage of this product is essential. Please read your manual carefully before exercising.

Please keep all children away from the equipment during use and when equipment is unattended.

Always wear appropriate clothing, including athletic shoes, when exercising. Do not wear loose clothing that could become caught
during exercising.

Make sure that all bolts and nuts are tightened prior to. Periodic maintenance is required on all exercise equipment to keep it in
good condition. Check for loose bolts and hardware before each use.

Before beginning:

How you begin your exercise program depends on your physical condition. If you have been inactive for several years, or are
severely overweight, you must start slowly and increase your time gradually, a few minutes per week.

Initially you may be able to exercise only for a few minutes in your target zone. However, your aerobic fitness will improve over the
next six to eight weeks. Don’t be discouraged if it takes longer. It’s important to work at your own pace. Ultimately, you’ll be able
to exercise continuously for 30 minutes. And the better your aerobic fitness, the harder you will have to work to stay in your target
zone. But remember these essentials:

IMPORTANT STEPS

• Contact your physician before starting a workout or training program. Have your doctor review your training and diet
programs to advise you of a workout routine you should adopt.

• Begin your training program slowly with realistic goals that have been set by you and your doctor.

• Supplement your program with some type of aerobic exercise such as walking, jogging, swimming, dancing and/or

bicycling. Monitor your pulse frequently. If you do not have an electronic heart rate monitor, have your physician show
you the proper way to manually check your pulse by using your wrist or neck. Establish your target heart rate based on
your age and condition.

• Drink plenty of fluids during the course of your routine. You must replace the water content lost from excessive exercising
to avoid dehydration. Avoid drinking large amounts of cold liquids. Fluids should be at room temperature when
consumed.

www.cybexinternational.com 45

Finding your pulse:

To make sure your heart is beating in its target zone, you’ll need to know how to monitor your heart rate. The easiest way is to feel
the pulse in the carotid artery on the left side of your neck, in the notch between the windpipe and the large neck muscles. When
you detect your pulse, use as little pressure as possible while you are counting beats. Too much pressure on your carotid artery will
result in abnormally low heart rates. Count the number of beats in ten seconds, and then multiply that number by six. This gives
you the number of beats per minute.

How fast should your heart beat during aerobic exercise? Fast enough to reach and stay in its “target zone,” a range of beats per
minute that is largely determined by your age and physical condition. To determine your target zone, consult the chart we have
provided.

TARGET HEART RATE

200

FIND YOUR TARGET HEART RATE

180

160

140

120

100

80

YOUR HEART RATE in beats per minute

YOUR AGE in years

20 25 30 35 40 45 50 55 60 65 70

Aerobic exercise:

Is any sustained activity that sends oxygen to your muscles via your heart and lungs. It will improve the fitness of your lungs and
heart: your body’s most important muscle. Aerobic fitness is promoted by any activity that uses your large muscle groups - arms,
legs or buttocks, for example. Your heart beats quickly and you breathe deeply. An aerobic exercise should be part of your entire
exercise routine.

ADVANCED: Sports, athletic conditioning or interval training

FITNESS: Optimal training, aerobic or cardiovascular

HEALTH: Beginner, low intensity with long duration produces fat burning

www.cybexinternational.com 46

Targeted muscle groups:

The exercise routine that is performed on this product will develop primarily lower body muscle groups. These muscle groups are
shown in gray color on the chart below.

MUSCLE CHART

MUSCLE GROUPS

A Deltoid muscles Gastrocnemius muscles

B Pectoral muscles Trapezius muscles

C Bicep muscle Tricep muscles

D Abdominal muscles Latissimus muscles

E Writs flexor muscles Gluteus muscles

F Quadricep muscles Hamstring muscles

G

H

I

J

K

L

www.cybexinternational.com 47

Warm up and cool down:

A successful exercise program consists of a warm-up, aerobic exercise, and a cool-down. Do the entire program at least two and
preferably three times a week, resting for a day between workouts. After several months, you can increase your workouts to four or
five times per week.
Warming up is an important part of your workout, and should begin every session. It prepares your body for more strenuous
exercise by heating up and stretching out your muscles, increasing your circulation and pulse rate, and delivering more oxygen to
your muscles. At the end of your workout, repeat these exercises to reduce sore muscle problems. We suggest the following
warm-up and cool-down exercises:

Toe Touch:

Slowly bend forward from
your waist, letting your back
and shoulders relax as you
stretch toward your toes.
Reach down as far as you
can and hold for 15 counts.

STRETCHING ROUTINE

Shoulder Lift:

Lift your right shoulder up
toward your ear for one
count. Then lift your left
shoulder up for one count as
you lower your right
shoulder.

Inner Thigh Stretch:

Sit with the soles of your feet
together with your knees
pointing outward. Pull your
feet as close into your groin
as possible. Gently push
your knees towards the floor.
Hold for 15 counts.

Side Stretch:

Open your arms to the side
and continue lifting them until
they are over your head.
Reach your right arm as far
upward toward the ceiling as
you can for one count. Feel
the stretch up your right side.
Repeat this action with your
left arm.

Head Roll:

Rotate your head to the right
for one count, feeling the
stretch up the left side of your
neck. Next, rotate your head
back for one count, stretching
your chin to the ceiling and
letting your mouth open.
Rotate your head to the left
for one count, and finally,
drop your head to your chest
for one count.

Hamstring Stretch:

Sit with your right leg
extended. Rest the sole of
your left foot against your
right inner thigh. Stretch
toward your toe as far as
possible. Hold for 15 counts.
Relax and then repeat with
left leg extended.

Calf-Achilles Stretch:

Lean against a wall with your
left leg in front of the right
and your arms forward. Keep
your right leg straight and the
left foot on the floor; then
bend the left leg and lean
forward by moving your hips
toward the wall. Hold, and
then repeat on the other side
for 15 counts.

www.cybexinternational.com 48

Troubleshooting

NOTE: Do not touch any internal electric wires. Contact Cybex Customer Service for a list of certified Cybex Service Technicians

in your area.

Home Arc Trainer will not start:

1. Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a properly grounded outlet and
the surge protector is turned on (refer to the Power Requirements section in this manual).

2. Check the circuit breaker reset switch located on the front of the Home Arc Trainer. Turn the power off, wait 5 minutes then
press the rest switch.

3. Check the house electrical breaker box and the circuit breaker for the room the Home Arc Trainer is located in. If it has tripped,
reset or have an electrician replace the breaker in home.

4. Have an electrician check for inadequate voltage at the outlet.

Home Arc Trainer looses power during use:

1. Check the circuit breaker reset switch located on the front of the Home Arc Trainer. Turn the power off, wait 5 minutes then
press the rest switch.

2. Check the house electrical breaker box and the circuit breaker for the room the Home Arc Trainer is located in. If it has tripped,
reset or have an electrician replace the breaker in home.

Contacting Customer Service:

Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time.

For customers living in the USA, contact Cybex Customer Service at 888-462-9239.

For customers living outside he USA, contact Cybex Customer Service at 508-533-4300 or fax [phone].

Order parts and find information on the web at for by e-mail at [e-mail].

TROUBLESHOOTING

Copyright 2008 Greenmaster Industrial Corp. All rights reserved.